diff options
Diffstat (limited to 'dts/Bindings/power/supply')
-rw-r--r-- | dts/Bindings/power/supply/act8945a-charger.txt | 2 | ||||
-rw-r--r-- | dts/Bindings/power/supply/bq24257.txt | 2 | ||||
-rw-r--r-- | dts/Bindings/power/supply/lp8727_charger.txt | 1 | ||||
-rw-r--r-- | dts/Bindings/power/supply/maxim,ds2760.txt | 26 | ||||
-rw-r--r-- | dts/Bindings/power/supply/maxim,max14656.txt | 1 | ||||
-rw-r--r-- | dts/Bindings/power/supply/rt9455_charger.txt | 2 | ||||
-rw-r--r-- | dts/Bindings/power/supply/sbs_sbs-battery.txt | 12 | ||||
-rw-r--r-- | dts/Bindings/power/supply/sbs_sbs-charger.txt | 2 |
8 files changed, 34 insertions, 14 deletions
diff --git a/dts/Bindings/power/supply/act8945a-charger.txt b/dts/Bindings/power/supply/act8945a-charger.txt index b86ecada4f..c7dfb7cecf 100644 --- a/dts/Bindings/power/supply/act8945a-charger.txt +++ b/dts/Bindings/power/supply/act8945a-charger.txt @@ -9,8 +9,6 @@ Required properties: - interrupts: <a b> where a is the interrupt number and b is a field that represents an encoding of the sense and level information for the interrupt. - - interrupt-parent: the phandle for the interrupt controller that - services interrupts for this device. Optional properties: - active-semi,input-voltage-threshold-microvolt: unit: mV; diff --git a/dts/Bindings/power/supply/bq24257.txt b/dts/Bindings/power/supply/bq24257.txt index d693702c9c..f8f5a1685b 100644 --- a/dts/Bindings/power/supply/bq24257.txt +++ b/dts/Bindings/power/supply/bq24257.txt @@ -6,8 +6,6 @@ Required properties: * "ti,bq24251" * "ti,bq24257" - reg: integer, i2c address of the device. -- interrupt-parent: Should be the phandle for the interrupt controller. Use in - conjunction with "interrupts". - interrupts: Interrupt mapping for GPIO IRQ (configure for both edges). Use in conjunction with "interrupt-parent". - ti,battery-regulation-voltage: integer, maximum charging voltage in uV. diff --git a/dts/Bindings/power/supply/lp8727_charger.txt b/dts/Bindings/power/supply/lp8727_charger.txt index 2246bc5c87..0355a4b68f 100644 --- a/dts/Bindings/power/supply/lp8727_charger.txt +++ b/dts/Bindings/power/supply/lp8727_charger.txt @@ -5,7 +5,6 @@ Required properties: - reg: I2C slave address 27h Optional properties: -- interrupt-parent: interrupt controller node (see interrupt binding[0]) - interrupts: interrupt specifier (see interrupt binding[0]) - debounce-ms: interrupt debounce time. (u32) diff --git a/dts/Bindings/power/supply/maxim,ds2760.txt b/dts/Bindings/power/supply/maxim,ds2760.txt new file mode 100644 index 0000000000..55967a0bee --- /dev/null +++ b/dts/Bindings/power/supply/maxim,ds2760.txt @@ -0,0 +1,26 @@ +Devicetree bindings for Maxim DS2760 +==================================== + +The ds2760 is a w1 slave device and must hence have its sub-node in DT +under a w1 bus master node. + +The device exposes a power supply, so the details described in +Documentation/devicetree/bindings/power/supply/power_supply.txt apply. + +Required properties: +- compatible: must be "maxim,ds2760" + +Optional properties: +- power-supplies: Refers to one or more power supplies connected to + this battery. +- maxim,pmod-enabled: This boolean property enables the DS2760 to enter + sleep mode when the DQ line goes low for greater + than 2 seconds and leave sleep Mode when the DQ + line goes high. +- maxim,cache-time-ms: Time im milliseconds to cache the data for. When + this time expires, the values are read again from + the hardware. Defaults to 1000. +- rated-capacity-microamp-hours: + The rated capacity of the battery, in mAh. + If not specified, the value stored in the + non-volatile chip memory is used. diff --git a/dts/Bindings/power/supply/maxim,max14656.txt b/dts/Bindings/power/supply/maxim,max14656.txt index d6e8dfd0a5..f956247d49 100644 --- a/dts/Bindings/power/supply/maxim,max14656.txt +++ b/dts/Bindings/power/supply/maxim,max14656.txt @@ -3,7 +3,6 @@ Maxim MAX14656 / AL32 USB Charger Detector Required properties : - compatible : "maxim,max14656"; - reg: i2c slave address -- interrupt-parent: the phandle for the interrupt controller - interrupts: interrupt line Example: diff --git a/dts/Bindings/power/supply/rt9455_charger.txt b/dts/Bindings/power/supply/rt9455_charger.txt index 5d9ad5cf2c..1e6107c757 100644 --- a/dts/Bindings/power/supply/rt9455_charger.txt +++ b/dts/Bindings/power/supply/rt9455_charger.txt @@ -4,8 +4,6 @@ Required properties: - compatible: it should contain one of the following: "richtek,rt9455". - reg: integer, i2c address of the device. -- interrupt-parent: the phandle for the interrupt controller that - services interrupts for this device. - interrupts: interrupt mapping for GPIO IRQ, it should be configured with IRQ_TYPE_LEVEL_LOW flag. - richtek,output-charge-current: integer, output current from the charger to the diff --git a/dts/Bindings/power/supply/sbs_sbs-battery.txt b/dts/Bindings/power/supply/sbs_sbs-battery.txt index c40e8926fa..4e78e51018 100644 --- a/dts/Bindings/power/supply/sbs_sbs-battery.txt +++ b/dts/Bindings/power/supply/sbs_sbs-battery.txt @@ -2,7 +2,11 @@ SBS sbs-battery ~~~~~~~~~~ Required properties : - - compatible : "sbs,sbs-battery" + - compatible: "<vendor>,<part-number>", "sbs,sbs-battery" as fallback. The + part number compatible string might be used in order to take care of + vendor specific registers. + Known <vendor>,<part-number>: + ti,bq20z75 Optional properties : - sbs,i2c-retry-count : The number of times to retry i2c transactions on i2c @@ -14,9 +18,9 @@ Optional properties : Example: - bq20z75@b { - compatible = "sbs,sbs-battery"; - reg = < 0xb >; + battery@b { + compatible = "ti,bq20z75", "sbs,sbs-battery"; + reg = <0xb>; sbs,i2c-retry-count = <2>; sbs,poll-retry-count = <10>; sbs,battery-detect-gpios = <&gpio-controller 122 1>; diff --git a/dts/Bindings/power/supply/sbs_sbs-charger.txt b/dts/Bindings/power/supply/sbs_sbs-charger.txt index a3719623a9..84e74151ee 100644 --- a/dts/Bindings/power/supply/sbs_sbs-charger.txt +++ b/dts/Bindings/power/supply/sbs_sbs-charger.txt @@ -7,8 +7,6 @@ Required properties: specific registers. Optional properties: -- interrupt-parent: Should be the phandle for the interrupt controller. Use in - conjunction with "interrupts". - interrupts: Interrupt mapping for GPIO IRQ. Use in conjunction with "interrupt-parent". If an interrupt is not provided the driver will switch automatically to polling. |