diff options
Diffstat (limited to 'dts/Bindings/regulator/nxp,pca9450-regulator.yaml')
| -rw-r--r-- | dts/Bindings/regulator/nxp,pca9450-regulator.yaml | 195 |
1 files changed, 195 insertions, 0 deletions
diff --git a/dts/Bindings/regulator/nxp,pca9450-regulator.yaml b/dts/Bindings/regulator/nxp,pca9450-regulator.yaml new file mode 100644 index 0000000000..3d469b8e97 --- /dev/null +++ b/dts/Bindings/regulator/nxp,pca9450-regulator.yaml @@ -0,0 +1,195 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/nxp,pca9450-regulator.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NXP PCA9450A/B/C Power Management Integrated Circuit regulators + +maintainers: + - Robin Gong <yibin.gong@nxp.com> + +description: | + Regulator nodes should be named to BUCK_<number> and LDO_<number>. The + definition for each of these nodes is defined using the standard + binding for regulators at + Documentation/devicetree/bindings/regulator/regulator.txt. + Datasheet is available at + https://www.nxp.com/docs/en/data-sheet/PCA9450DS.pdf + +# The valid names for PCA9450 regulator nodes are: +# BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6, +# LDO1, LDO2, LDO3, LDO4, LDO5 +# Note: Buck3 removed on PCA9450B and connect with Buck1 on PCA9450C. + +properties: + compatible: + enum: + - nxp,pca9450a + - nxp,pca9450b + - nxp,pca9450c + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + regulators: + type: object + description: | + list of regulators provided by this controller + + patternProperties: + "^LDO[1-5]$": + type: object + $ref: regulator.yaml# + description: + Properties for single LDO regulator. + + unevaluatedProperties: false + + "^BUCK[1-6]$": + type: object + $ref: regulator.yaml# + description: + Properties for single BUCK regulator. + + properties: + nxp,dvs-run-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 600000 + maximum: 2187500 + description: + PMIC default "RUN" state voltage in uV. Only Buck1~3 have such + dvs(dynamic voltage scaling) property. + + nxp,dvs-standby-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 600000 + maximum: 2187500 + description: + PMIC default "STANDBY" state voltage in uV. Only Buck1~3 have such + dvs(dynamic voltage scaling) property. + + unevaluatedProperties: false + + additionalProperties: false + + sd-vsel-gpios: + description: GPIO that is used to switch LDO5 between being configured by + LDO5CTRL_L or LDO5CTRL_H register. Use this if the SD_VSEL signal is + connected to a host GPIO. + + nxp,i2c-lt-enable: + type: boolean + description: + Indicates that the I2C Level Translator is used. + + nxp,wdog_b-warm-reset: + type: boolean + description: + When WDOG_B signal is asserted a warm reset will be done instead of cold + reset. + +required: + - compatible + - reg + - interrupts + - regulators + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + pmic: pmic@25 { + compatible = "nxp,pca9450b"; + reg = <0x25>; + pinctrl-0 = <&pinctrl_pmic>; + interrupt-parent = <&gpio1>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; + + regulators { + buck1: BUCK1 { + regulator-name = "BUCK1"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <2187500>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <3125>; + }; + buck2: BUCK2 { + regulator-name = "BUCK2"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <2187500>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <3125>; + nxp,dvs-run-voltage = <950000>; + nxp,dvs-standby-voltage = <850000>; + }; + buck4: BUCK4 { + regulator-name = "BUCK4"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <3400000>; + regulator-boot-on; + regulator-always-on; + }; + buck5: BUCK5 { + regulator-name = "BUCK5"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <3400000>; + regulator-boot-on; + regulator-always-on; + }; + buck6: BUCK6 { + regulator-name = "BUCK6"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <3400000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1: LDO1 { + regulator-name = "LDO1"; + regulator-min-microvolt = <1600000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + ldo2: LDO2 { + regulator-name = "LDO2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1150000>; + regulator-boot-on; + regulator-always-on; + }; + ldo3: LDO3 { + regulator-name = "LDO3"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + ldo4: LDO4 { + regulator-name = "LDO4"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + ldo5: LDO5 { + regulator-name = "LDO5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; + }; |