diff options
Diffstat (limited to 'dts/Bindings/regulator/rohm,bd71847-regulator.yaml')
| -rw-r--r-- | dts/Bindings/regulator/rohm,bd71847-regulator.yaml | 156 |
1 files changed, 156 insertions, 0 deletions
diff --git a/dts/Bindings/regulator/rohm,bd71847-regulator.yaml b/dts/Bindings/regulator/rohm,bd71847-regulator.yaml new file mode 100644 index 0000000000..7ba4ccf723 --- /dev/null +++ b/dts/Bindings/regulator/rohm,bd71847-regulator.yaml @@ -0,0 +1,156 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/rohm,bd71847-regulator.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ROHM BD71847 and BD71850 Power Management Integrated Circuit regulators + +maintainers: + - Matti Vaittinen <mazziesaccount@gmail.com> + +description: | + List of regulators provided by this controller. BD71847 regulators node + should be sub node of the BD71847 MFD node. See BD71847 MFD bindings at + Documentation/devicetree/bindings/mfd/rohm,bd71847-pmic.yaml + Regulator nodes should be named to BUCK_<number> and LDO_<number>. The + definition for each of these nodes is defined using the standard + binding for regulators at + Documentation/devicetree/bindings/regulator/regulator.txt. + Note that if BD71847 starts at RUN state you probably want to use + regulator-boot-on at least for BUCK5. LDO6 is supplied by it and it must + not be disabled by driver at startup. If BUCK5 is disabled at startup the + voltage monitoring for LDO5/LDO6 can cause PMIC to reset. + +# The valid names for BD71847 regulator nodes are: +# BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6 +# LDO1, LDO2, LDO3, LDO4, LDO5, LDO6 + +patternProperties: + "^LDO[1-6]$": + type: object + $ref: regulator.yaml# + description: + Properties for single LDO regulator. + + properties: + regulator-name: + pattern: "^ldo[1-6]$" + description: + should be "ldo1", ..., "ldo6" + + unevaluatedProperties: false + + "^BUCK[1-6]$": + type: object + $ref: regulator.yaml# + description: + Properties for single BUCK regulator. + + properties: + regulator-name: + pattern: "^buck[1-6]$" + description: + should be "buck1", ..., "buck6" + + rohm,dvs-run-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 1300000 + description: + PMIC default "RUN" state voltage in uV. See below table for + bucks which support this. 0 means disabled. + + rohm,dvs-idle-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 1300000 + description: + PMIC default "IDLE" state voltage in uV. See below table for + bucks which support this. 0 means disabled. + + rohm,dvs-suspend-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 1300000 + description: + PMIC default "SUSPEND" state voltage in uV. See below table for + bucks which support this. 0 means disabled. + + # Supported default DVS states: + # + # BD71847: + # buck | dvs-run-voltage | dvs-idle-voltage | dvs-suspend-voltage + # ---------------------------------------------------------------- + # 1 | supported | supported | supported + # ---------------------------------------------------------------- + # 2 | supported | supported | not supported + # ---------------------------------------------------------------- + # rest | not supported | not supported | not supported + + # BD718(47/50) power outputs can either be controlled by the PMIC internal + # hardware state machine or by software. If you need regulators to be + # turned ON/OFF for example based on PMIC_STBY_REQ line (which toggles + # PMIC HW state machine) - then you should set this property. + # Tradeoff is that then SW can't control the ON/OFF state for this + # regulator (other than invoking a PMIC state change). + rohm,no-regulator-enable-control: + description: | + Enable/Disable control of this regulator must be left to the + PMIC hardware state machine. + type: boolean + + # Setups where regulator (especially the buck8) output voltage is scaled + # by adding external connection where some other regulator output is + # connected to feedback-pin (over suitable resistors) is getting popular + # amongst users of BD71837. (This allows for example scaling down the + # buck8 voltages to suit lover GPU voltages for projects where buck8 is + # (ab)used to supply power for GPU. + # + # So we allow describing this external connection from DT and scale the + # voltages accordingly. This is what the connection should look like: + # + # |---------------| + # | buck 8 |-------+----->Vout + # | | | + # |---------------| | + # | | + # | | + # +-------+--R2----+ + # | + # R1 + # | + # V FB-pull-up + # + # Here the buck output is sifted according to formula: + # + # Vout_o = Vo - (Vpu - Vo)*R2/R1 + # Linear_step = step_orig*(R1+R2)/R1 + # + # where: + # Vout_o is adjusted voltage output at vsel reg value 0 + # Vo is original voltage output at vsel reg value 0 + # Vpu is the pull-up voltage V FB-pull-up in the picture + # R1 and R2 are resistor values. + + rohm,fb-pull-up-microvolt: + description: + Feedback-pin has pull-up connection to adjust voltage range. This is + the used pull-up voltage before R1. + + rohm,feedback-pull-up-r1-ohms: + description: + Feedback-pin has pull-up connection to adjust voltage range. This is + the used R1 resistor. + + rohm,feedback-pull-up-r2-ohms: + description: + Feedback-pin has pull-up connection to adjust voltage range. This is + the used R2 resistor. + + required: + - regulator-name + + unevaluatedProperties: false + +additionalProperties: false |