summaryrefslogtreecommitdiffstats
path: root/dts/Bindings/regulator
diff options
context:
space:
mode:
Diffstat (limited to 'dts/Bindings/regulator')
-rw-r--r--dts/Bindings/regulator/act8865-regulator.txt4
-rw-r--r--dts/Bindings/regulator/max77802.txt35
-rw-r--r--dts/Bindings/regulator/regulator.txt22
-rw-r--r--dts/Bindings/regulator/sky81452-regulator.txt10
4 files changed, 67 insertions, 4 deletions
diff --git a/dts/Bindings/regulator/act8865-regulator.txt b/dts/Bindings/regulator/act8865-regulator.txt
index 865614b34..dad635807 100644
--- a/dts/Bindings/regulator/act8865-regulator.txt
+++ b/dts/Bindings/regulator/act8865-regulator.txt
@@ -5,6 +5,10 @@ Required properties:
- compatible: "active-semi,act8846" or "active-semi,act8865"
- reg: I2C slave address
+Optional properties:
+- system-power-controller: Telling whether or not this pmic is controlling
+ the system power. See Documentation/devicetree/bindings/power/power-controller.txt .
+
Any standard regulator properties can be used to configure the single regulator.
The valid names for regulators are:
diff --git a/dts/Bindings/regulator/max77802.txt b/dts/Bindings/regulator/max77802.txt
index 5aeaffc0f..79e547644 100644
--- a/dts/Bindings/regulator/max77802.txt
+++ b/dts/Bindings/regulator/max77802.txt
@@ -25,6 +25,29 @@ with their hardware counterparts as follow. The valid names are:
example: LDO1, LDO2, LDO35.
-BUCKn : for BUCKs, where n can lie in range 1 to 10.
example: BUCK1, BUCK5, BUCK10.
+
+The max77802 regulator supports two different operating modes: Normal and Low
+Power Mode. Some regulators support the modes to be changed at startup or by
+the consumers during normal operation while others only support to change the
+mode during system suspend. The standard regulator suspend states binding can
+be used to configure the regulator operating mode.
+
+The regulators that support the standard "regulator-initial-mode" property,
+changing their mode during normal operation are: LDOs 1, 3, 20 and 21.
+
+The possible values for "regulator-initial-mode" and "regulator-mode" are:
+ 1: Normal regulator voltage output mode.
+ 3: Low Power which reduces the quiescent current down to only 1uA
+
+The list of valid modes are defined in the dt-bindings/clock/maxim,max77802.h
+header and can be included by device tree source files.
+
+The standard "regulator-mode" property can only be used for regulators that
+support changing their mode to Low Power Mode during suspend. These regulators
+are: BUCKs 2-4 and LDOs 1-35. Also, it only takes effect if the regulator has
+been enabled for the given suspend state using "regulator-on-in-suspend" and
+has not been disabled for that state using "regulator-off-in-suspend".
+
Example:
max77802@09 {
@@ -36,11 +59,23 @@ Example:
#size-cells = <0>;
regulators {
+ ldo1_reg: LDO1 {
+ regulator-name = "vdd_1v0";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-initial-mode = <MAX77802_OPMODE_LP>;
+ };
+
ldo11_reg: LDO11 {
regulator-name = "vdd_ldo11";
regulator-min-microvolt = <1900000>;
regulator-max-microvolt = <1900000>;
regulator-always-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-mode = <MAX77802_OPMODE_LP>;
+ };
};
buck1_reg: BUCK1 {
diff --git a/dts/Bindings/regulator/regulator.txt b/dts/Bindings/regulator/regulator.txt
index 86074334e..abb26b58c 100644
--- a/dts/Bindings/regulator/regulator.txt
+++ b/dts/Bindings/regulator/regulator.txt
@@ -19,6 +19,24 @@ Optional properties:
design requires. This property describes the total system ramp time
required due to the combination of internal ramping of the regulator itself,
and board design issues such as trace capacitance and load on the supply.
+- regulator-state-mem sub-root node for Suspend-to-RAM mode
+ : suspend to memory, the device goes to sleep, but all data stored in memory,
+ only some external interrupt can wake the device.
+- regulator-state-disk sub-root node for Suspend-to-DISK mode
+ : suspend to disk, this state operates similarly to Suspend-to-RAM,
+ but includes a final step of writing memory contents to disk.
+- regulator-state-[mem/disk] node has following common properties:
+ - regulator-on-in-suspend: regulator should be on in suspend state.
+ - regulator-off-in-suspend: regulator should be off in suspend state.
+ - regulator-suspend-microvolt: regulator should be set to this voltage
+ in suspend.
+ - regulator-mode: operating mode in the given suspend state.
+ The set of possible operating modes depends on the capabilities of
+ every hardware so the valid modes are documented on each regulator
+ device tree binding document.
+- regulator-initial-mode: initial operating mode. The set of possible operating
+ modes depends on the capabilities of every hardware so each device binding
+ documentation explains which values the regulator supports.
Deprecated properties:
- regulator-compatible: If a regulator chip contains multiple
@@ -34,6 +52,10 @@ Example:
regulator-max-microvolt = <2500000>;
regulator-always-on;
vin-supply = <&vin>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
};
Regulator Consumers:
diff --git a/dts/Bindings/regulator/sky81452-regulator.txt b/dts/Bindings/regulator/sky81452-regulator.txt
index 882455e9b..f9acbc1f3 100644
--- a/dts/Bindings/regulator/sky81452-regulator.txt
+++ b/dts/Bindings/regulator/sky81452-regulator.txt
@@ -1,6 +1,7 @@
SKY81452 voltage regulator
Required properties:
+- regulator node named lout.
- any required generic properties defined in regulator.txt
Optional properties:
@@ -9,8 +10,9 @@ Optional properties:
Example:
regulator {
- /* generic regulator properties */
- regulator-name = "touch_en";
- regulator-min-microvolt = <4500000>;
- regulator-max-microvolt = <8000000>;
+ lout {
+ regulator-name = "sky81452-lout";
+ regulator-min-microvolt = <4500000>;
+ regulator-max-microvolt = <8000000>;
+ };
};