diff options
Diffstat (limited to 'dts/Bindings/soc/qcom/rpmh-rsc.txt')
| -rw-r--r-- | dts/Bindings/soc/qcom/rpmh-rsc.txt | 137 |
1 files changed, 0 insertions, 137 deletions
diff --git a/dts/Bindings/soc/qcom/rpmh-rsc.txt b/dts/Bindings/soc/qcom/rpmh-rsc.txt deleted file mode 100644 index 9b86d1eff2..0000000000 --- a/dts/Bindings/soc/qcom/rpmh-rsc.txt +++ /dev/null @@ -1,137 +0,0 @@ -RPMH RSC: ------------- - -Resource Power Manager Hardened (RPMH) is the mechanism for communicating with -the hardened resource accelerators on Qualcomm SoCs. Requests to the resources -can be written to the Trigger Command Set (TCS) registers and using a (addr, -val) pair and triggered. Messages in the TCS are then sent in sequence over an -internal bus. - -The hardware block (Direct Resource Voter or DRV) is a part of the h/w entity -(Resource State Coordinator a.k.a RSC) that can handle multiple sleep and -active/wake resource requests. Multiple such DRVs can exist in a SoC and can -be written to from Linux. The structure of each DRV follows the same template -with a few variations that are captured by the properties here. - -A TCS may be triggered from Linux or triggered by the F/W after all the CPUs -have powered off to facilitate idle power saving. TCS could be classified as - - - ACTIVE /* Triggered by Linux */ - SLEEP /* Triggered by F/W */ - WAKE /* Triggered by F/W */ - CONTROL /* Triggered by F/W */ - -The order in which they are described in the DT, should match the hardware -configuration. - -Requests can be made for the state of a resource, when the subsystem is active -or idle. When all subsystems like Modem, GPU, CPU are idle, the resource state -will be an aggregate of the sleep votes from each of those subsystems. Clients -may request a sleep value for their shared resources in addition to the active -mode requests. - -Properties: - -- compatible: - Usage: required - Value type: <string> - Definition: Should be "qcom,rpmh-rsc". - -- reg: - Usage: required - Value type: <prop-encoded-array> - Definition: The first register specifies the base address of the - DRV(s). The number of DRVs in the dependent on the RSC. - The tcs-offset specifies the start address of the - TCS in the DRVs. - -- reg-names: - Usage: required - Value type: <string> - Definition: Maps the register specified in the reg property. Must be - "drv-0", "drv-1", "drv-2" etc and "tcs-offset". The - -- interrupts: - Usage: required - Value type: <prop-encoded-interrupt> - Definition: The interrupt that trips when a message complete/response - is received for this DRV from the accelerators. - -- qcom,drv-id: - Usage: required - Value type: <u32> - Definition: The id of the DRV in the RSC block that will be used by - this controller. - -- qcom,tcs-config: - Usage: required - Value type: <prop-encoded-array> - Definition: The tuple defining the configuration of TCS. - Must have 2 cells which describe each TCS type. - <type number_of_tcs>. - The order of the TCS must match the hardware - configuration. - - Cell #1 (TCS Type): TCS types to be specified - - ACTIVE_TCS - SLEEP_TCS - WAKE_TCS - CONTROL_TCS - - Cell #2 (Number of TCS): <u32> - -- label: - Usage: optional - Value type: <string> - Definition: Name for the RSC. The name would be used in trace logs. - -Drivers that want to use the RSC to communicate with RPMH must specify their -bindings as child nodes of the RSC controllers they wish to communicate with. - -Example 1: - -For a TCS whose RSC base address is is 0x179C0000 and is at a DRV id of 2, the -register offsets for DRV2 start at 0D00, the register calculations are like -this - -DRV0: 0x179C0000 -DRV2: 0x179C0000 + 0x10000 = 0x179D0000 -DRV2: 0x179C0000 + 0x10000 * 2 = 0x179E0000 -TCS-OFFSET: 0xD00 - - apps_rsc: rsc@179c0000 { - label = "apps_rsc"; - compatible = "qcom,rpmh-rsc"; - reg = <0x179c0000 0x10000>, - <0x179d0000 0x10000>, - <0x179e0000 0x10000>; - reg-names = "drv-0", "drv-1", "drv-2"; - interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; - qcom,tcs-offset = <0xd00>; - qcom,drv-id = <2>; - qcom,tcs-config = <ACTIVE_TCS 2>, - <SLEEP_TCS 3>, - <WAKE_TCS 3>, - <CONTROL_TCS 1>; - }; - -Example 2: - -For a TCS whose RSC base address is 0xAF20000 and is at DRV id of 0, the -register offsets for DRV0 start at 01C00, the register calculations are like -this - -DRV0: 0xAF20000 -TCS-OFFSET: 0x1C00 - - disp_rsc: rsc@af20000 { - label = "disp_rsc"; - compatible = "qcom,rpmh-rsc"; - reg = <0xaf20000 0x10000>; - reg-names = "drv-0"; - interrupts = <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>; - qcom,tcs-offset = <0x1c00>; - qcom,drv-id = <0>; - qcom,tcs-config = <ACTIVE_TCS 0>, - <SLEEP_TCS 1>, - <WAKE_TCS 1>, - <CONTROL_TCS 0>; - }; |