diff options
Diffstat (limited to 'dts/Bindings/sound/cirrus,cs35l41.yaml')
| -rw-r--r-- | dts/Bindings/sound/cirrus,cs35l41.yaml | 209 |
1 files changed, 209 insertions, 0 deletions
diff --git a/dts/Bindings/sound/cirrus,cs35l41.yaml b/dts/Bindings/sound/cirrus,cs35l41.yaml new file mode 100644 index 0000000000..14dea1feef --- /dev/null +++ b/dts/Bindings/sound/cirrus,cs35l41.yaml @@ -0,0 +1,209 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sound/cirrus,cs35l41.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Cirrus Logic CS35L41 Speaker Amplifier + +maintainers: + - david.rhodes@cirrus.com + +description: | + CS35L41 is a boosted mono Class D amplifier with DSP + speaker protection and equalization + +properties: + compatible: + enum: + - cirrus,cs35l40 + - cirrus,cs35l41 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + '#sound-dai-cells': + description: + The first cell indicating the audio interface. + const: 1 + + reset-gpios: + maxItems: 1 + + VA-supply: + description: voltage regulator phandle for the VA supply + + VP-supply: + description: voltage regulator phandle for the VP supply + + cirrus,boost-peak-milliamp: + description: + Boost-converter peak current limit in mA. + Configures the peak current by monitoring the current through the boost FET. + Range starts at 1600 mA and goes to a maximum of 4500 mA with increments + of 50 mA. See section 4.3.6 of the datasheet for details. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1600 + maximum: 4500 + default: 4500 + + cirrus,boost-ind-nanohenry: + description: + Boost inductor value, expressed in nH. Valid + values include 1000, 1200, 1500 and 2200. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1000 + maximum: 2200 + + cirrus,boost-cap-microfarad: + description: + Total equivalent boost capacitance on the VBST + and VAMP pins, derated at 11 volts DC. The value must be rounded to the + nearest integer and expressed in uF. + $ref: /schemas/types.yaml#/definitions/uint32 + + cirrus,asp-sdout-hiz: + description: + Audio serial port SDOUT Hi-Z control. Sets the Hi-Z + configuration for SDOUT pin of amplifier. + 0 = Logic 0 during unused slots, and while all transmit channels disabled + 1 = Hi-Z during unused slots but logic 0 while all transmit channels disabled + 2 = (Default) Logic 0 during unused slots, but Hi-Z while all transmit channels disabled + 3 = Hi-Z during unused slots and while all transmit channels disabled + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 3 + default: 2 + + cirrus,boost-type: + description: + Configures the type of Boost being used. + Internal boost requires boost-peak-milliamp, boost-ind-nanohenry and + boost-cap-microfarad. + External Boost must have GPIO1 as GPIO output. GPIO1 will be set high to + enable boost voltage. + Shared boost allows two amplifiers to share a single boost circuit by + communicating on the MDSYNC bus. The active amplifier controls the boost + circuit using combined data from both amplifiers. GPIO1 should be + configured for Sync when shared boost is used. Shared boost is not + compatible with External boost. Active amplifier requires + boost-peak-milliamp, boost-ind-nanohenry and boost-cap-microfarad. + 0 = Internal Boost + 1 = External Boost + 2 = Shared Boost Active + 3 = Shared Boost Passive + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 3 + + cirrus,gpio1-polarity-invert: + description: + Boolean which specifies whether the GPIO1 + level is inverted. If this property is not present the level is not inverted. + type: boolean + + cirrus,gpio1-output-enable: + description: + Boolean which specifies whether the GPIO1 pin + is configured as an output. If this property is not present the + pin will be configured as an input. + type: boolean + + cirrus,gpio1-src-select: + description: + Configures the function of the GPIO1 pin. + Note that the options are different from the GPIO2 pin + 0 = High Impedance (Default) + 1 = GPIO + 2 = Sync + 3 = MCLK input + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 3 + + cirrus,gpio2-polarity-invert: + description: + Boolean which specifies whether the GPIO2 + level is inverted. If this property is not present the level is not inverted. + type: boolean + + cirrus,gpio2-output-enable: + description: + Boolean which specifies whether the GPIO2 pin + is configured as an output. If this property is not present the + pin will be configured as an input. + type: boolean + + cirrus,gpio2-src-select: + description: + Configures the function of the GPIO2 pin. + Note that the options are different from the GPIO1 pin. + 0 = High Impedance (Default) + 1 = GPIO + 2 = Open Drain INTB + 3 = MCLK input + 4 = Push-pull INTB (active low) + 5 = Push-pull INT (active high) + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 5 + +required: + - compatible + - reg + - "#sound-dai-cells" + +allOf: + - $ref: dai-common.yaml# + - if: + properties: + cirrus,boost-type: + const: 0 + then: + required: + - cirrus,boost-peak-milliamp + - cirrus,boost-ind-nanohenry + - cirrus,boost-cap-microfarad + else: + if: + properties: + cirrus,boost-type: + const: 1 + then: + required: + - cirrus,gpio1-output-enable + - cirrus,gpio1-src-select + properties: + cirrus,boost-peak-milliamp: false + cirrus,boost-ind-nanohenry: false + cirrus,boost-cap-microfarad: false + cirrus,gpio1-src-select: + enum: [1] + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + spi { + #address-cells = <1>; + #size-cells = <0>; + + cs35l41: speaker-amp@2 { + #sound-dai-cells = <1>; + compatible = "cirrus,cs35l41"; + reg = <2>; + VA-supply = <&dummy_vreg>; + VP-supply = <&dummy_vreg>; + reset-gpios = <&gpio 110 GPIO_ACTIVE_HIGH>; + + cirrus,boost-type = <0>; + cirrus,boost-peak-milliamp = <4500>; + cirrus,boost-ind-nanohenry = <1000>; + cirrus,boost-cap-microfarad = <15>; + }; + }; |