diff options
Diffstat (limited to 'dts/Bindings/sound/cirrus,cs35l41.yaml')
-rw-r--r-- | dts/Bindings/sound/cirrus,cs35l41.yaml | 92 |
1 files changed, 72 insertions, 20 deletions
diff --git a/dts/Bindings/sound/cirrus,cs35l41.yaml b/dts/Bindings/sound/cirrus,cs35l41.yaml index 3235702ce4..14dea1feef 100644 --- a/dts/Bindings/sound/cirrus,cs35l41.yaml +++ b/dts/Bindings/sound/cirrus,cs35l41.yaml @@ -22,6 +22,9 @@ properties: reg: maxItems: 1 + interrupts: + maxItems: 1 + '#sound-dai-cells': description: The first cell indicating the audio interface. @@ -42,7 +45,7 @@ properties: Configures the peak current by monitoring the current through the boost FET. Range starts at 1600 mA and goes to a maximum of 4500 mA with increments of 50 mA. See section 4.3.6 of the datasheet for details. - $ref: "/schemas/types.yaml#/definitions/uint32" + $ref: /schemas/types.yaml#/definitions/uint32 minimum: 1600 maximum: 4500 default: 4500 @@ -51,7 +54,7 @@ properties: description: Boost inductor value, expressed in nH. Valid values include 1000, 1200, 1500 and 2200. - $ref: "/schemas/types.yaml#/definitions/uint32" + $ref: /schemas/types.yaml#/definitions/uint32 minimum: 1000 maximum: 2200 @@ -60,7 +63,7 @@ properties: Total equivalent boost capacitance on the VBST and VAMP pins, derated at 11 volts DC. The value must be rounded to the nearest integer and expressed in uF. - $ref: "/schemas/types.yaml#/definitions/uint32" + $ref: /schemas/types.yaml#/definitions/uint32 cirrus,asp-sdout-hiz: description: @@ -70,11 +73,32 @@ properties: 1 = Hi-Z during unused slots but logic 0 while all transmit channels disabled 2 = (Default) Logic 0 during unused slots, but Hi-Z while all transmit channels disabled 3 = Hi-Z during unused slots and while all transmit channels disabled - $ref: "/schemas/types.yaml#/definitions/uint32" + $ref: /schemas/types.yaml#/definitions/uint32 minimum: 0 maximum: 3 default: 2 + cirrus,boost-type: + description: + Configures the type of Boost being used. + Internal boost requires boost-peak-milliamp, boost-ind-nanohenry and + boost-cap-microfarad. + External Boost must have GPIO1 as GPIO output. GPIO1 will be set high to + enable boost voltage. + Shared boost allows two amplifiers to share a single boost circuit by + communicating on the MDSYNC bus. The active amplifier controls the boost + circuit using combined data from both amplifiers. GPIO1 should be + configured for Sync when shared boost is used. Shared boost is not + compatible with External boost. Active amplifier requires + boost-peak-milliamp, boost-ind-nanohenry and boost-cap-microfarad. + 0 = Internal Boost + 1 = External Boost + 2 = Shared Boost Active + 3 = Shared Boost Passive + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 3 + cirrus,gpio1-polarity-invert: description: Boolean which specifies whether the GPIO1 @@ -96,7 +120,7 @@ properties: 1 = GPIO 2 = Sync 3 = MCLK input - $ref: "/schemas/types.yaml#/definitions/uint32" + $ref: /schemas/types.yaml#/definitions/uint32 minimum: 0 maximum: 3 @@ -123,7 +147,7 @@ properties: 3 = MCLK input 4 = Push-pull INTB (active low) 5 = Push-pull INT (active high) - $ref: "/schemas/types.yaml#/definitions/uint32" + $ref: /schemas/types.yaml#/definitions/uint32 minimum: 0 maximum: 5 @@ -131,27 +155,55 @@ required: - compatible - reg - "#sound-dai-cells" - - cirrus,boost-peak-milliamp - - cirrus,boost-ind-nanohenry - - cirrus,boost-cap-microfarad -additionalProperties: false +allOf: + - $ref: dai-common.yaml# + - if: + properties: + cirrus,boost-type: + const: 0 + then: + required: + - cirrus,boost-peak-milliamp + - cirrus,boost-ind-nanohenry + - cirrus,boost-cap-microfarad + else: + if: + properties: + cirrus,boost-type: + const: 1 + then: + required: + - cirrus,gpio1-output-enable + - cirrus,gpio1-src-select + properties: + cirrus,boost-peak-milliamp: false + cirrus,boost-ind-nanohenry: false + cirrus,boost-cap-microfarad: false + cirrus,gpio1-src-select: + enum: [1] + +unevaluatedProperties: false examples: - | + #include <dt-bindings/gpio/gpio.h> + spi { #address-cells = <1>; #size-cells = <0>; - cs35l41: cs35l41@2 { - #sound-dai-cells = <1>; - compatible = "cirrus,cs35l41"; - reg = <2>; - VA-supply = <&dummy_vreg>; - VP-supply = <&dummy_vreg>; - reset-gpios = <&gpio 110 0>; - cirrus,boost-peak-milliamp = <4500>; - cirrus,boost-ind-nanohenry = <1000>; - cirrus,boost-cap-microfarad = <15>; + cs35l41: speaker-amp@2 { + #sound-dai-cells = <1>; + compatible = "cirrus,cs35l41"; + reg = <2>; + VA-supply = <&dummy_vreg>; + VP-supply = <&dummy_vreg>; + reset-gpios = <&gpio 110 GPIO_ACTIVE_HIGH>; + + cirrus,boost-type = <0>; + cirrus,boost-peak-milliamp = <4500>; + cirrus,boost-ind-nanohenry = <1000>; + cirrus,boost-cap-microfarad = <15>; }; }; |