diff options
Diffstat (limited to 'dts/Bindings/sound/cirrus,cs42l42.yaml')
| -rw-r--r-- | dts/Bindings/sound/cirrus,cs42l42.yaml | 225 |
1 files changed, 225 insertions, 0 deletions
diff --git a/dts/Bindings/sound/cirrus,cs42l42.yaml b/dts/Bindings/sound/cirrus,cs42l42.yaml new file mode 100644 index 0000000000..31800f70e9 --- /dev/null +++ b/dts/Bindings/sound/cirrus,cs42l42.yaml @@ -0,0 +1,225 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sound/cirrus,cs42l42.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Cirrus Logic CS42L42 audio CODEC + +maintainers: + - patches@opensource.cirrus.com + +description: + The CS42L42 is a low-power audio codec designed for portable applications. + It provides a high-dynamic range, stereo DAC for audio playback and a mono + high-dynamic-range ADC for audio capture. There is an integrated headset + detection block. + +properties: + compatible: + enum: + - cirrus,cs42l42 + + reg: + description: + The I2C address of the CS42L42. + maxItems: 1 + + VP-supply: + description: + VP power supply. + + VCP-supply: + description: + Charge pump power supply. + + VD_FILT-supply: + description: + FILT+ power supply. + + VL-supply: + description: + Logic power supply. + + VA-supply: + description: + Analog power supply. + + reset-gpios: + description: + This pin will be asserted and then deasserted to reset the + CS42L42 before communication starts. + maxItems: 1 + + interrupts: + description: + Interrupt for CS42L42 IRQ line. + maxItems: 1 + + cirrus,ts-inv: + description: | + Sets the behaviour of the jack plug detect switch. + + 0 - (Default) Shorted to tip when unplugged, open when plugged. + This is "inverted tip sense (ITS)" in the datasheet. + + 1 - Open when unplugged, shorted to tip when plugged. + This is "normal tip sense (TS)" in the datasheet. + + The CS42L42_TS_INV_* defines are available for this. + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 1 + + cirrus,ts-dbnc-rise: + description: | + Debounce the rising edge of TIP_SENSE_PLUG. With no + debounce, the tip sense pin might be noisy on a plug event. + + 0 - 0ms + 1 - 125ms + 2 - 250ms + 3 - 500ms + 4 - 750ms + 5 - 1s (Default) + 6 - 1.25s + 7 - 1.5s + + The CS42L42_TS_DBNCE_* defines are available for this. + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 7 + + cirrus,ts-dbnc-fall: + description: | + Debounce the falling edge of TIP_SENSE_UNPLUG. With no + debounce, the tip sense pin might be noisy on an unplug event. + + 0 - 0ms + 1 - 125ms + 2 - 250ms + 3 - 500ms + 4 - 750ms + 5 - 1s (Default) + 6 - 1.25s + 7 - 1.5s + + The CS42L42_TS_DBNCE_* defines are available for this. + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 7 + + cirrus,btn-det-init-dbnce: + description: | + This sets how long to wait after enabling button detection + interrupts before servicing button interrupts, to allow the + HS bias time to settle. Value is in milliseconds. + There may be erroneous button interrupts if this debounce time + is too short. + + 0ms - 200ms, + Default = 100ms + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 200 + + cirrus,btn-det-event-dbnce: + description: | + This sets how long to wait after receiving a button press + interrupt before processing it. Allows time for the button + press to make a clean connection with the bias resistors. + Value is in milliseconds. + + 0ms - 20ms, + Default = 10ms + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 20 + + cirrus,bias-lvls: + description: | + For a level-detect headset button scheme, each button will bias + the mic pin to a certain voltage. To determine which button was + pressed, the voltage is compared to sequential, decreasing + voltages, until the compared voltage < bias voltage. + For different hardware setups, a designer might want to tweak this. + This is an array of descending values for the comparator voltage, + given as percent of the HSBIAS voltage. + + Array of 4 values, each 0-63 + < x1 x2 x3 x4 > + Default = < 15 8 4 1 > + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 4 + maxItems: 4 + items: + minimum: 0 + maximum: 63 + + cirrus,hs-bias-ramp-rate: + description: | + If present this sets the rate that the HS bias should rise and fall. + The actual rise and fall times depend on external hardware (the + datasheet gives several rise and fall time examples). + + 0 - Fast rise time; slow, load-dependent fall time + 1 - Fast + 2 - Slow (default) + 3 - Slowest + + The CS42L42_HSBIAS_RAMP_* defines are available for this. + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 3 + + cirrus,hs-bias-sense-disable: + description: | + If present the HSBIAS sense is disabled. Configures HSBIAS output + current sense through the external 2.21-k resistor. HSBIAS_SENSE + is a hardware feature to reduce the potential pop noise when the + headset plug is removed slowly. But on some platforms ESD voltage + will affect it causing plug detection to fail, especially with CTIA + headset type. For different hardware setups, a designer might want + to tweak default behavior. + type: boolean + +required: + - compatible + - reg + - VP-supply + - VCP-supply + - VD_FILT-supply + - VL-supply + - VA-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/sound/cs42l42.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + cs42l42: cs42l42@48 { + compatible = "cirrus,cs42l42"; + reg = <0x48>; + VA-supply = <&dummy_vreg>; + VP-supply = <&dummy_vreg>; + VCP-supply = <&dummy_vreg>; + VD_FILT-supply = <&dummy_vreg>; + VL-supply = <&dummy_vreg>; + + reset-gpios = <&axi_gpio_0 1 0>; + interrupt-parent = <&gpio0>; + interrupts = <55 8>; + + cirrus,ts-inv = <CS42L42_TS_INV_DIS>; + cirrus,ts-dbnc-rise = <CS42L42_TS_DBNCE_1000>; + cirrus,ts-dbnc-fall = <CS42L42_TS_DBNCE_0>; + cirrus,btn-det-init-dbnce = <100>; + cirrus,btn-det-event-dbnce = <10>; + cirrus,bias-lvls = <0x0F 0x08 0x04 0x01>; + cirrus,hs-bias-ramp-rate = <CS42L42_HSBIAS_RAMP_SLOW>; + }; + }; |