summaryrefslogtreecommitdiffstats
path: root/dts/Bindings/sound/nau8825.txt
diff options
context:
space:
mode:
Diffstat (limited to 'dts/Bindings/sound/nau8825.txt')
-rw-r--r--dts/Bindings/sound/nau8825.txt105
1 files changed, 0 insertions, 105 deletions
diff --git a/dts/Bindings/sound/nau8825.txt b/dts/Bindings/sound/nau8825.txt
deleted file mode 100644
index d16d96839b..0000000000
--- a/dts/Bindings/sound/nau8825.txt
+++ /dev/null
@@ -1,105 +0,0 @@
-Nuvoton NAU8825 audio codec
-
-This device supports I2C only.
-
-Required properties:
- - compatible : Must be "nuvoton,nau8825"
-
- - reg : the I2C address of the device. This is either 0x1a (CSB=0) or 0x1b (CSB=1).
-
-Optional properties:
- - nuvoton,jkdet-enable: Enable jack detection via JKDET pin.
- - nuvoton,jkdet-pull-enable: Enable JKDET pin pull. If set - pin pull enabled,
- otherwise pin in high impedance state.
- - nuvoton,jkdet-pull-up: Pull-up JKDET pin. If set then JKDET pin is pull up, otherwise pull down.
- - nuvoton,jkdet-polarity: JKDET pin polarity. 0 - active high, 1 - active low.
-
- - nuvoton,vref-impedance: VREF Impedance selection
- 0 - Open
- 1 - 25 kOhm
- 2 - 125 kOhm
- 3 - 2.5 kOhm
-
- - nuvoton,micbias-voltage: Micbias voltage level.
- 0 - VDDA
- 1 - VDDA
- 2 - VDDA * 1.1
- 3 - VDDA * 1.2
- 4 - VDDA * 1.3
- 5 - VDDA * 1.4
- 6 - VDDA * 1.53
- 7 - VDDA * 1.53
-
- - nuvoton,sar-threshold-num: Number of buttons supported
- - nuvoton,sar-threshold: Impedance threshold for each button. Array that contains up to 8 buttons configuration. SAR value is calculated as
- SAR = 255 * MICBIAS / SAR_VOLTAGE * R / (2000 + R)
- where MICBIAS is configured by 'nuvoton,micbias-voltage', SAR_VOLTAGE is configured by 'nuvoton,sar-voltage', R - button impedance.
- Refer datasheet section 10.2 for more information about threshold calculation.
-
- - nuvoton,sar-hysteresis: Button impedance measurement hysteresis.
-
- - nuvoton,sar-voltage: Reference voltage for button impedance measurement.
- 0 - VDDA
- 1 - VDDA
- 2 - VDDA * 1.1
- 3 - VDDA * 1.2
- 4 - VDDA * 1.3
- 5 - VDDA * 1.4
- 6 - VDDA * 1.53
- 7 - VDDA * 1.53
-
- - nuvoton,sar-compare-time: SAR compare time
- 0 - 500 ns
- 1 - 1 us
- 2 - 2 us
- 3 - 4 us
-
- - nuvoton,sar-sampling-time: SAR sampling time
- 0 - 2 us
- 1 - 4 us
- 2 - 8 us
- 3 - 16 us
-
- - nuvoton,short-key-debounce: Button short key press debounce time.
- 0 - 30 ms
- 1 - 50 ms
- 2 - 100 ms
- 3 - 30 ms
-
- - nuvoton,jack-insert-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms
- - nuvoton,jack-eject-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms
-
- - nuvoton,crosstalk-enable: make crosstalk function enable if set.
-
- - clocks: list of phandle and clock specifier pairs according to common clock bindings for the
- clocks described in clock-names
- - clock-names: should include "mclk" for the MCLK master clock
-
-Example:
-
- headset: nau8825@1a {
- compatible = "nuvoton,nau8825";
- reg = <0x1a>;
- interrupt-parent = <&gpio>;
- interrupts = <TEGRA_GPIO(E, 6) IRQ_TYPE_LEVEL_LOW>;
- nuvoton,jkdet-enable;
- nuvoton,jkdet-pull-enable;
- nuvoton,jkdet-pull-up;
- nuvoton,jkdet-polarity = <GPIO_ACTIVE_LOW>;
- nuvoton,vref-impedance = <2>;
- nuvoton,micbias-voltage = <6>;
- // Setup 4 buttons impedance according to Android specification
- nuvoton,sar-threshold-num = <4>;
- nuvoton,sar-threshold = <0xc 0x1e 0x38 0x60>;
- nuvoton,sar-hysteresis = <1>;
- nuvoton,sar-voltage = <0>;
- nuvoton,sar-compare-time = <0>;
- nuvoton,sar-sampling-time = <0>;
- nuvoton,short-key-debounce = <2>;
- nuvoton,jack-insert-debounce = <7>;
- nuvoton,jack-eject-debounce = <7>;
- nuvoton,crosstalk-enable;
-
- clock-names = "mclk";
- clocks = <&tegra_car TEGRA210_CLK_CLK_OUT_2>;
- };