diff options
Diffstat (limited to 'dts/Bindings/sound/wm8994.txt')
-rw-r--r-- | dts/Bindings/sound/wm8994.txt | 83 |
1 files changed, 0 insertions, 83 deletions
diff --git a/dts/Bindings/sound/wm8994.txt b/dts/Bindings/sound/wm8994.txt deleted file mode 100644 index 68cccc4653..0000000000 --- a/dts/Bindings/sound/wm8994.txt +++ /dev/null @@ -1,83 +0,0 @@ -WM1811/WM8994/WM8958 audio CODEC - -These devices support both I2C and SPI (configured with pin strapping -on the board). - -Required properties: - - - compatible : One of "wlf,wm1811", "wlf,wm8994" or "wlf,wm8958". - - - reg : the I2C address of the device for I2C, the chip select - number for SPI. - - - gpio-controller : Indicates this device is a GPIO controller. - - #gpio-cells : Must be 2. The first cell is the pin number and the - second cell is used to specify optional parameters (currently unused). - - - AVDD2-supply, DBVDD1-supply, DBVDD2-supply, DBVDD3-supply, CPVDD-supply, - SPKVDD1-supply, SPKVDD2-supply : power supplies for the device, as covered - in Documentation/devicetree/bindings/regulator/regulator.txt - -Optional properties: - - - interrupts : The interrupt line the IRQ signal for the device is - connected to. This is optional, if it is not connected then none - of the interrupt related properties should be specified. - - interrupt-controller : These devices contain interrupt controllers - and may provide interrupt services to other devices if they have an - interrupt line connected. - - #interrupt-cells: the number of cells to describe an IRQ, this should be 2. - The first cell is the IRQ number. - The second cell is the flags, encoded as the trigger masks from - Documentation/devicetree/bindings/interrupt-controller/interrupts.txt - - - clocks : A list of up to two phandle and clock specifier pairs - - clock-names : A list of clock names sorted in the same order as clocks. - Valid clock names are "MCLK1" and "MCLK2". - - - wlf,gpio-cfg : A list of GPIO configuration register values. If absent, - no configuration of these registers is performed. If any value is - over 0xffff then the register will be left as default. If present 11 - values must be supplied. - - - wlf,micbias-cfg : Two MICBIAS register values for WM1811 or - WM8958. If absent the register defaults will be used. - - - wlf,ldo1ena : GPIO specifier for control of LDO1ENA input to device. - - wlf,ldo2ena : GPIO specifier for control of LDO2ENA input to device. - - - wlf,lineout1-se : If present LINEOUT1 is in single ended mode. - - wlf,lineout2-se : If present LINEOUT2 is in single ended mode. - - - wlf,lineout1-feedback : If present LINEOUT1 has common mode feedback - connected. - - wlf,lineout2-feedback : If present LINEOUT2 has common mode feedback - connected. - - - wlf,ldoena-always-driven : If present LDOENA is always driven. - - - wlf,spkmode-pu : If present enable the internal pull-up resistor on - the SPKMODE pin. - - - wlf,csnaddr-pd : If present enable the internal pull-down resistor on - the CS/ADDR pin. - -Example: - -wm8994: codec@1a { - compatible = "wlf,wm8994"; - reg = <0x1a>; - - gpio-controller; - #gpio-cells = <2>; - - lineout1-se; - - AVDD2-supply = <®ulator>; - CPVDD-supply = <®ulator>; - DBVDD1-supply = <®ulator>; - DBVDD2-supply = <®ulator>; - DBVDD3-supply = <®ulator>; - SPKVDD1-supply = <®ulator>; - SPKVDD2-supply = <®ulator>; -}; |