summaryrefslogtreecommitdiffstats
path: root/dts/Bindings/sound
diff options
context:
space:
mode:
Diffstat (limited to 'dts/Bindings/sound')
-rw-r--r--dts/Bindings/sound/axentia,tse850-pcm5142.txt88
-rw-r--r--dts/Bindings/sound/cs35l34.txt64
-rw-r--r--dts/Bindings/sound/cs42l42.txt110
-rw-r--r--dts/Bindings/sound/davinci-mcbsp.txt2
-rw-r--r--dts/Bindings/sound/qcom,apq8016-sbc.txt5
-rw-r--r--dts/Bindings/sound/qcom,msm8916-wcd-analog.txt85
-rw-r--r--dts/Bindings/sound/qcom,msm8916-wcd-digital.txt20
-rw-r--r--dts/Bindings/sound/rt5514.txt3
-rw-r--r--dts/Bindings/sound/rt5663.txt6
-rwxr-xr-xdts/Bindings/sound/rt5665.txt68
-rw-r--r--dts/Bindings/sound/samsung,tm2-audio.txt38
-rw-r--r--dts/Bindings/sound/sun4i-codec.txt65
-rw-r--r--dts/Bindings/sound/sun8i-codec-analog.txt16
-rw-r--r--dts/Bindings/sound/tlv320aic31xx.txt1
-rw-r--r--dts/Bindings/sound/wm8580.txt4
15 files changed, 564 insertions, 11 deletions
diff --git a/dts/Bindings/sound/axentia,tse850-pcm5142.txt b/dts/Bindings/sound/axentia,tse850-pcm5142.txt
new file mode 100644
index 0000000000..5b9b38f578
--- /dev/null
+++ b/dts/Bindings/sound/axentia,tse850-pcm5142.txt
@@ -0,0 +1,88 @@
+Devicetree bindings for the Axentia TSE-850 audio complex
+
+Required properties:
+ - compatible: "axentia,tse850-pcm5142"
+ - axentia,ssc-controller: The phandle of the atmel SSC controller used as
+ cpu dai.
+ - axentia,audio-codec: The phandle of the PCM5142 codec.
+ - axentia,add-gpios: gpio specifier that controls the mixer.
+ - axentia,loop1-gpios: gpio specifier that controls loop relays on channel 1.
+ - axentia,loop2-gpios: gpio specifier that controls loop relays on channel 2.
+ - axentia,ana-supply: Regulator that supplies the output amplifier. Must
+ support voltages in the 2V - 20V range, in 1V steps.
+
+The schematics explaining the gpios are as follows:
+
+ loop1 relays
+ IN1 +---o +------------+ o---+ OUT1
+ \ /
+ + +
+ | / |
+ +--o +--. |
+ | add | |
+ | V |
+ | .---. |
+ DAC +----------->|Sum|---+
+ | '---' |
+ | |
+ + +
+
+ IN2 +---o--+------------+--o---+ OUT2
+ loop2 relays
+
+The 'loop1' gpio pin controlls two relays, which are either in loop position,
+meaning that input and output are directly connected, or they are in mixer
+position, meaning that the signal is passed through the 'Sum' mixer. Similarly
+for 'loop2'.
+
+In the above, the 'loop1' relays are inactive, thus feeding IN1 to the mixer
+(if 'add' is active) and feeding the mixer output to OUT1. The 'loop2' relays
+are active, short-cutting the TSE-850 from channel 2. IN1, IN2, OUT1 and OUT2
+are TSE-850 connectors and DAC is the PCB name of the (filtered) output from
+the PCM5142 codec.
+
+Example:
+
+ &i2c {
+ codec: pcm5142@4c {
+ compatible = "ti,pcm5142";
+
+ reg = <0x4c>;
+
+ AVDD-supply = <&reg_3v3>;
+ DVDD-supply = <&reg_3v3>;
+ CPVDD-supply = <&reg_3v3>;
+
+ clocks = <&sck>;
+
+ pll-in = <3>;
+ pll-out = <6>;
+ };
+ };
+
+ ana: ana-reg {
+ compatible = "pwm-regulator";
+
+ regulator-name = "ANA";
+
+ pwms = <&pwm0 2 1000 PWM_POLARITY_INVERTED>;
+ pwm-dutycycle-unit = <1000>;
+ pwm-dutycycle-range = <100 1000>;
+
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <20000000>;
+ regulator-ramp-delay = <1000>;
+ };
+
+ sound {
+ compatible = "axentia,tse850-pcm5142";
+
+ axentia,ssc-controller = <&ssc0>;
+ axentia,audio-codec = <&codec>;
+
+ axentia,add-gpios = <&pioA 8 GPIO_ACTIVE_LOW>;
+ axentia,loop1-gpios = <&pioA 10 GPIO_ACTIVE_LOW>;
+ axentia,loop2-gpios = <&pioA 11 GPIO_ACTIVE_LOW>;
+
+ axentia,ana-supply = <&ana>;
+ };
diff --git a/dts/Bindings/sound/cs35l34.txt b/dts/Bindings/sound/cs35l34.txt
new file mode 100644
index 0000000000..b218ead2e6
--- /dev/null
+++ b/dts/Bindings/sound/cs35l34.txt
@@ -0,0 +1,64 @@
+CS35L34 Speaker Amplifier
+
+Required properties:
+
+ - compatible : "cirrus,cs35l34"
+
+ - reg : the I2C address of the device for I2C.
+
+ - VA-supply, VP-supply : power supplies for the device,
+ as covered in
+ Documentation/devicetree/bindings/regulator/regulator.txt.
+
+ - cirrus,boost-vtge-millivolt : Boost Voltage Value. Configures the boost
+ converter's output voltage in mV. The range is from VP to 8V with
+ increments of 100mV.
+
+ - cirrus,boost-nanohenry: Inductor value for boost converter. The value is
+ in nH and they can be values of 1000nH, 1100nH, 1200nH, 1500nH, and 2200nH.
+
+Optional properties:
+
+ - reset-gpios: GPIO used to reset the amplifier.
+
+ - interrupt-parent : Specifies the phandle of the interrupt controller to
+ which the IRQs from CS35L34 are delivered to.
+ - interrupts : IRQ line info CS35L34.
+ (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+ for further information relating to interrupt properties)
+
+ - cirrus,boost-peak-milliamp : Boost converter peak current limit in mA. The
+ range starts at 1200mA and goes to a maximum of 3840mA with increments of
+ 80mA. The default value is 2480mA.
+
+ - cirrus,i2s-sdinloc : ADSP SDIN I2S channel location. Indicates whether the
+ received mono data is in the left or right portion of the I2S frame
+ according to the AD0 pin or directly via this configuration.
+ 0x0 (Default) = Selected by AD0 input (if AD0 = LOW, use left channel),
+ 0x2 = Left,
+ 0x1 = Selected by the inversion of the AD0 input (if AD0 = LOW, use right
+ channel),
+ 0x3 = Right.
+
+ - cirrus,gain-zc-disable: Boolean property. If set, the gain change will take
+ effect without waiting for a zero cross.
+
+ - cirrus,tdm-rising-edge: Boolean property. If set, data is on the rising edge of
+ SCLK. Otherwise, data is on the falling edge of SCLK.
+
+
+Example:
+
+cs35l34: cs35l34@40 {
+ compatible = "cirrus,cs35l34";
+ reg = <0x40>;
+
+ interrupt-parent = <&gpio8>;
+ interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+
+ reset-gpios = <&gpio 10 0>;
+
+ cirrus,boost-vtge-milltvolt = <8000>; /* 8V */
+ cirrus,boost-ind-nanohenry = <1000>; /* 1uH */
+ cirrus,boost-peak-milliamp = <3000>; /* 3A */
+};
diff --git a/dts/Bindings/sound/cs42l42.txt b/dts/Bindings/sound/cs42l42.txt
new file mode 100644
index 0000000000..9a2c5e2423
--- /dev/null
+++ b/dts/Bindings/sound/cs42l42.txt
@@ -0,0 +1,110 @@
+CS42L42 audio CODEC
+
+Required properties:
+
+ - compatible : "cirrus,cs42l42"
+
+ - reg : the I2C address of the device for I2C.
+
+ - VP-supply, VCP-supply, VD_FILT-supply, VL-supply, VA-supply :
+ power supplies for the device, as covered in
+ Documentation/devicetree/bindings/regulator/regulator.txt.
+
+Optional properties:
+
+ - reset-gpios : a GPIO spec for the reset pin. If specified, it will be
+ deasserted before communication to the codec starts.
+
+ - interrupt-parent : Specifies the phandle of the interrupt controller to
+ which the IRQs from CS42L42 are delivered to.
+
+ - interrupts : IRQ line info CS42L42.
+ (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+ for further information relating to interrupt properties)
+
+ - cirrus,ts-inv : Boolean property. For jacks that invert the tip sense
+ polarity. Normal jacks will short tip sense pin to HS1 when headphones are
+ plugged in and leave tip sense floating when not plugged in. Inverting jacks
+ short tip sense when unplugged and float when plugged in.
+
+ 0 = (Default) Non-inverted
+ 1 = Inverted
+
+ - cirrus,ts-dbnc-rise : Debounce the rising edge of TIP_SENSE_PLUG. With no
+ debounce, the tip sense pin might be noisy on a plug event.
+
+ 0 - 0ms,
+ 1 - 125ms,
+ 2 - 250ms,
+ 3 - 500ms,
+ 4 - 750ms,
+ 5 - (Default) 1s,
+ 6 - 1.25s,
+ 7 - 1.5s,
+
+ - cirrus,ts-dbnc-fall : Debounce the falling edge of TIP_SENSE_UNPLUG.
+ With no debounce, the tip sense pin might be noisy on an unplug event.
+
+ 0 - 0ms,
+ 1 - 125ms,
+ 2 - 250ms,
+ 3 - 500ms,
+ 4 - 750ms,
+ 5 - (Default) 1s,
+ 6 - 1.25s,
+ 7 - 1.5s,
+
+ - cirrus,btn-det-init-dbnce : This sets how long the driver sleeps after
+ enabling button detection interrupts. After auto-detection and before
+ servicing button interrupts, the HS bias needs time to settle. If you
+ don't wait, there is possibility for erroneous button interrupt.
+
+ 0ms - 200ms,
+ Default = 100ms
+
+ - cirrus,btn-det-event-dbnce : This sets how long the driver delays after
+ receiving a button press interrupt. With level detect interrupts, you want
+ to wait a small amount of time to make sure the button press is making a
+ clean connection with the bias resistors.
+
+ 0ms - 20ms,
+ Default = 10ms
+
+ - cirrus,bias-lvls : For a level-detect headset button scheme, each button
+ will bias the mic pin to a certain voltage. To determine which button was
+ pressed, the driver will compare this biased voltage to sequential,
+ decreasing voltages and will stop when a comparator is tripped,
+ indicating a comparator voltage < bias voltage. This value represents a
+ percentage of the internally generated HS bias voltage. For different
+ hardware setups, a designer might want to tweak this. This is an array of
+ descending values for the comparator voltage.
+
+ Array of 4 values
+ Each 0-63
+ < x1 x2 x3 x4 >
+ Default = < 15 8 4 1>
+
+
+Example:
+
+cs42l42: cs42l42@48 {
+ compatible = "cirrus,cs42l42";
+ reg = <0x48>;
+ VA-supply = <&dummy_vreg>;
+ VP-supply = <&dummy_vreg>;
+ VCP-supply = <&dummy_vreg>;
+ VD_FILT-supply = <&dummy_vreg>;
+ VL-supply = <&dummy_vreg>;
+
+ reset-gpios = <&axi_gpio_0 1 0>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <55 8>
+
+ cirrus,ts-inv = <0x00>;
+ cirrus,ts-dbnc-rise = <0x05>;
+ cirrus,ts-dbnc-fall = <0x00>;
+ cirrus,btn-det-init-dbnce = <100>;
+ cirrus,btn-det-event-dbnce = <10>;
+ cirrus,bias-lvls = <0x0F 0x08 0x04 0x01>;
+ cirrus,hs-bias-ramp-rate = <0x02>;
+}; \ No newline at end of file
diff --git a/dts/Bindings/sound/davinci-mcbsp.txt b/dts/Bindings/sound/davinci-mcbsp.txt
index 55b53e1fd7..e0b6165c9c 100644
--- a/dts/Bindings/sound/davinci-mcbsp.txt
+++ b/dts/Bindings/sound/davinci-mcbsp.txt
@@ -43,7 +43,7 @@ mcbsp0: mcbsp@1d10000 {
<0x00310000 0x1000>;
reg-names = "mpu", "dat";
interrupts = <97 98>;
- interrupts-names = "rx", "tx";
+ interrupt-names = "rx", "tx";
dmas = <&edma0 3 1
&edma0 2 1>;
dma-names = "tx", "rx";
diff --git a/dts/Bindings/sound/qcom,apq8016-sbc.txt b/dts/Bindings/sound/qcom,apq8016-sbc.txt
index d9d8635ff9..6a4aadc4ce 100644
--- a/dts/Bindings/sound/qcom,apq8016-sbc.txt
+++ b/dts/Bindings/sound/qcom,apq8016-sbc.txt
@@ -44,8 +44,7 @@ Required dai-link subnodes:
Required CPU/CODEC subnodes properties:
-link-name : Name of the dai link.
--sound-dai : phandle and port of CPU/CODEC
--capture-dai : phandle and port of CPU/CODEC
+-sound-dai : phandle/s and port of CPU/CODEC
Example:
@@ -73,7 +72,7 @@ sound: sound {
sound-dai = <&lpass MI2S_PRIMARY>;
};
codec {
- sound-dai = <&wcd_codec 0>;
+ sound-dai = <&lpass_codec 0>, <&wcd_codec 0>;
};
};
diff --git a/dts/Bindings/sound/qcom,msm8916-wcd-analog.txt b/dts/Bindings/sound/qcom,msm8916-wcd-analog.txt
new file mode 100644
index 0000000000..ccb401cfef
--- /dev/null
+++ b/dts/Bindings/sound/qcom,msm8916-wcd-analog.txt
@@ -0,0 +1,85 @@
+msm8916 analog audio CODEC
+
+Bindings for codec Analog IP which is integrated in pmic pm8916,
+
+## Bindings for codec core on pmic:
+
+Required properties
+ - compatible = "qcom,pm8916-wcd-analog-codec";
+ - reg: represents the slave base address provided to the peripheral.
+ - interrupt-parent : The parent interrupt controller.
+ - interrupts: List of interrupts in given SPMI peripheral.
+ - interrupt-names: Names specified to above list of interrupts in same
+ order. List of supported interrupt names are:
+ "cdc_spk_cnp_int" - Speaker click and pop interrupt.
+ "cdc_spk_clip_int" - Speaker clip interrupt.
+ "cdc_spk_ocp_int" - Speaker over current protect interrupt.
+ "mbhc_ins_rem_det1" - jack insert removal detect interrupt 1.
+ "mbhc_but_rel_det" - button release interrupt.
+ "mbhc_but_press_det" - button press event
+ "mbhc_ins_rem_det" - jack insert removal detect interrupt.
+ "mbhc_switch_int" - multi button headset interrupt.
+ "cdc_ear_ocp_int" - Earphone over current protect interrupt.
+ "cdc_hphr_ocp_int" - Headphone R over current protect interrupt.
+ "cdc_hphl_ocp_det" - Headphone L over current protect interrupt.
+ "cdc_ear_cnp_int" - earphone cnp interrupt.
+ "cdc_hphr_cnp_int" - hphr click and pop interrupt.
+ "cdc_hphl_cnp_int" - hphl click and pop interrupt.
+
+ - clocks: Handle to mclk.
+ - clock-names: should be "mclk"
+ - vdd-cdc-io-supply: phandle to VDD_CDC_IO regulator DT node.
+ - vdd-cdc-tx-rx-cx-supply: phandle to VDD_CDC_TX/RX/CX regulator DT node.
+ - vdd-micbias-supply: phandle of VDD_MICBIAS supply's regulator DT node.
+
+Optional Properties:
+- qcom,micbias1-ext-cap: boolean, present if micbias1 has external capacitor
+ connected.
+- qcom,micbias2-ext-cap: boolean, present if micbias2 has external capacitor
+ connected.
+
+Example:
+
+spmi_bus {
+ ...
+ audio-codec@f000{
+ compatible = "qcom,pm8916-wcd-analog-codec";
+ reg = <0xf000 0x200>;
+ reg-names = "pmic-codec-core";
+ clocks = <&gcc GCC_CODEC_DIGCODEC_CLK>;
+ clock-names = "mclk";
+ interrupt-parent = <&spmi_bus>;
+ interrupts = <0x1 0xf0 0x0 IRQ_TYPE_NONE>,
+ <0x1 0xf0 0x1 IRQ_TYPE_NONE>,
+ <0x1 0xf0 0x2 IRQ_TYPE_NONE>,
+ <0x1 0xf0 0x3 IRQ_TYPE_NONE>,
+ <0x1 0xf0 0x4 IRQ_TYPE_NONE>,
+ <0x1 0xf0 0x5 IRQ_TYPE_NONE>,
+ <0x1 0xf0 0x6 IRQ_TYPE_NONE>,
+ <0x1 0xf0 0x7 IRQ_TYPE_NONE>,
+ <0x1 0xf1 0x0 IRQ_TYPE_NONE>,
+ <0x1 0xf1 0x1 IRQ_TYPE_NONE>,
+ <0x1 0xf1 0x2 IRQ_TYPE_NONE>,
+ <0x1 0xf1 0x3 IRQ_TYPE_NONE>,
+ <0x1 0xf1 0x4 IRQ_TYPE_NONE>,
+ <0x1 0xf1 0x5 IRQ_TYPE_NONE>;
+ interrupt-names = "cdc_spk_cnp_int",
+ "cdc_spk_clip_int",
+ "cdc_spk_ocp_int",
+ "mbhc_ins_rem_det1",
+ "mbhc_but_rel_det",
+ "mbhc_but_press_det",
+ "mbhc_ins_rem_det",
+ "mbhc_switch_int",
+ "cdc_ear_ocp_int",
+ "cdc_hphr_ocp_int",
+ "cdc_hphl_ocp_det",
+ "cdc_ear_cnp_int",
+ "cdc_hphr_cnp_int",
+ "cdc_hphl_cnp_int";
+ VDD-CDC-IO-supply = <&pm8916_l5>;
+ VDD-CDC-TX-RX-CX-supply = <&pm8916_l5>;
+ VDD-MICBIAS-supply = <&pm8916_l13>;
+ #sound-dai-cells = <1>;
+ };
+};
diff --git a/dts/Bindings/sound/qcom,msm8916-wcd-digital.txt b/dts/Bindings/sound/qcom,msm8916-wcd-digital.txt
new file mode 100644
index 0000000000..1c8e4cb251
--- /dev/null
+++ b/dts/Bindings/sound/qcom,msm8916-wcd-digital.txt
@@ -0,0 +1,20 @@
+msm8916 digital audio CODEC
+
+## Bindings for codec core in lpass:
+
+Required properties
+ - compatible = "qcom,msm8916-wcd-digital-codec";
+ - reg: address space for lpass codec.
+ - clocks: Handle to mclk and ahbclk
+ - clock-names: should be "mclk", "ahbix-clk".
+
+Example:
+
+audio-codec@771c000{
+ compatible = "qcom,msm8916-wcd-digital-codec";
+ reg = <0x0771c000 0x400>;
+ clocks = <&gcc GCC_ULTAUDIO_AHBFABRIC_IXFABRIC_CLK>,
+ <&gcc GCC_CODEC_DIGCODEC_CLK>;
+ clock-names = "ahbix-clk", "mclk";
+ #sound-dai-cells = <1>;
+};
diff --git a/dts/Bindings/sound/rt5514.txt b/dts/Bindings/sound/rt5514.txt
index 9cabfc18cb..929ca6756b 100644
--- a/dts/Bindings/sound/rt5514.txt
+++ b/dts/Bindings/sound/rt5514.txt
@@ -13,6 +13,9 @@ Optional properties:
- clocks: The phandle of the master clock to the CODEC
- clock-names: Should be "mclk"
+- realtek,dmic-init-delay-ms
+ Set the DMIC initial delay (ms) to wait it ready.
+
Pins on the device (for linking into audio routes) for RT5514:
* DMIC1L
diff --git a/dts/Bindings/sound/rt5663.txt b/dts/Bindings/sound/rt5663.txt
index 7d3c974c6e..70eaeaed2b 100644
--- a/dts/Bindings/sound/rt5663.txt
+++ b/dts/Bindings/sound/rt5663.txt
@@ -1,10 +1,10 @@
-RT5663/RT5668 audio CODEC
+RT5663 audio CODEC
This device supports I2C only.
Required properties:
-- compatible : One of "realtek,rt5663" or "realtek,rt5668".
+- compatible : "realtek,rt5663".
- reg : The I2C address of the device.
@@ -12,7 +12,7 @@ Required properties:
Optional properties:
-Pins on the device (for linking into audio routes) for RT5663/RT5668:
+Pins on the device (for linking into audio routes) for RT5663:
* IN1P
* IN1N
diff --git a/dts/Bindings/sound/rt5665.txt b/dts/Bindings/sound/rt5665.txt
new file mode 100755
index 0000000000..419c892196
--- /dev/null
+++ b/dts/Bindings/sound/rt5665.txt
@@ -0,0 +1,68 @@
+RT5665/RT5666/RT5668 audio CODEC
+
+This device supports I2C only.
+
+Required properties:
+
+- compatible : One of "realtek,rt5665", "realtek,rt5666" or "realtek,rt5668".
+
+- reg : The I2C address of the device.
+
+- interrupts : The CODEC's interrupt output.
+
+Optional properties:
+
+- realtek,in1-differential
+- realtek,in2-differential
+- realtek,in3-differential
+- realtek,in4-differential
+ Boolean. Indicate MIC1/2/3/4 input are differential, rather than single-ended.
+
+- realtek,dmic1-data-pin
+ 0: dmic1 is not used
+ 1: using GPIO4 pin as dmic1 data pin
+ 2: using IN2N pin as dmic2 data pin
+
+- realtek,dmic2-data-pin
+ 0: dmic2 is not used
+ 1: using GPIO5 pin as dmic2 data pin
+ 2: using IN2P pin as dmic2 data pin
+
+- realtek,jd-src
+ 0: No JD is used
+ 1: using JD1 as JD source
+
+- realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin.
+
+Pins on the device (for linking into audio routes) for RT5659/RT5658:
+
+ * DMIC L1
+ * DMIC R1
+ * DMIC L2
+ * DMIC R2
+ * IN1P
+ * IN1N
+ * IN2P
+ * IN2N
+ * IN3P
+ * IN3N
+ * IN4P
+ * IN4N
+ * HPOL
+ * HPOR
+ * LOUTL
+ * LOUTR
+ * MONOOUT
+ * PDML
+ * PDMR
+
+Example:
+
+rt5659 {
+ compatible = "realtek,rt5665";
+ reg = <0x1b>;
+ interrupt-parent = <&gpio>;
+ interrupts = <TEGRA_GPIO(W, 3) GPIO_ACTIVE_HIGH>;
+ realtek,ldo1-en-gpios =
+ <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>;
+};
diff --git a/dts/Bindings/sound/samsung,tm2-audio.txt b/dts/Bindings/sound/samsung,tm2-audio.txt
new file mode 100644
index 0000000000..94442e5673
--- /dev/null
+++ b/dts/Bindings/sound/samsung,tm2-audio.txt
@@ -0,0 +1,38 @@
+Samsung Exynos5433 TM2(E) audio complex with WM5110 codec
+
+Required properties:
+
+ - compatible : "samsung,tm2-audio"
+ - model : the user-visible name of this sound complex
+ - audio-codec : the phandle of the wm5110 audio codec node,
+ as described in ../mfd/arizona.txt
+ - i2s-controller : the phandle of the I2S controller
+ - audio-amplifier : the phandle of the MAX98504 amplifier
+ - samsung,audio-routing : a list of the connections between audio components;
+ each entry is a pair of strings, the first being the
+ connection's sink, the second being the connection's
+ source; valid names for sources and sinks are the
+ WM5110's and MAX98504's pins and the jacks on the
+ board: HP, SPK, Main Mic, Sub Mic, Third Mic,
+ Headset Mic
+ - mic-bias-gpios : GPIO pin that enables the Main Mic bias regulator
+
+
+Example:
+
+sound {
+ compatible = "samsung,tm2-audio";
+ audio-codec = <&wm5110>;
+ i2s-controller = <&i2s0>;
+ audio-amplifier = <&max98504>;
+ mic-bias-gpios = <&gpr3 2 0>;
+ model = "wm5110";
+ samsung,audio-routing =
+ "HP", "HPOUT1L",
+ "HP", "HPOUT1R",
+ "SPK", "SPKOUT",
+ "SPKOUT", "HPOUT2L",
+ "SPKOUT", "HPOUT2R",
+ "Main Mic", "MICBIAS2",
+ "IN1R", "Main Mic";
+};
diff --git a/dts/Bindings/sound/sun4i-codec.txt b/dts/Bindings/sound/sun4i-codec.txt
index 0dce690f78..3033bd8aab 100644
--- a/dts/Bindings/sound/sun4i-codec.txt
+++ b/dts/Bindings/sound/sun4i-codec.txt
@@ -1,8 +1,12 @@
* Allwinner A10 Codec
Required properties:
-- compatible: must be either "allwinner,sun4i-a10-codec" or
- "allwinner,sun7i-a20-codec"
+- compatible: must be one of the following compatibles:
+ - "allwinner,sun4i-a10-codec"
+ - "allwinner,sun6i-a31-codec"
+ - "allwinner,sun7i-a20-codec"
+ - "allwinner,sun8i-a23-codec"
+ - "allwinner,sun8i-h3-codec"
- reg: must contain the registers location and length
- interrupts: must contain the codec interrupt
- dmas: DMA channels for tx and rx dma. See the DMA client binding,
@@ -17,6 +21,43 @@ Required properties:
Optional properties:
- allwinner,pa-gpios: gpio to enable external amplifier
+Required properties for the following compatibles:
+ - "allwinner,sun6i-a31-codec"
+ - "allwinner,sun8i-a23-codec"
+ - "allwinner,sun8i-h3-codec"
+- resets: phandle to the reset control for this device
+- allwinner,audio-routing: A list of the connections between audio components.
+ Each entry is a pair of strings, the first being the
+ connection's sink, the second being the connection's
+ source. Valid names include:
+
+ Audio pins on the SoC:
+ "HP"
+ "HPCOM"
+ "LINEIN"
+ "LINEOUT" (not on sun8i-a23)
+ "MIC1"
+ "MIC2"
+ "MIC3" (sun6i-a31 only)
+
+ Microphone biases from the SoC:
+ "HBIAS"
+ "MBIAS"
+
+ Board connectors:
+ "Headphone"
+ "Headset Mic"
+ "Line In"
+ "Line Out"
+ "Mic"
+ "Speaker"
+
+Required properties for the following compatibles:
+ - "allwinner,sun8i-a23-codec"
+ - "allwinner,sun8i-h3-codec"
+- allwinner,codec-analog-controls: A phandle to the codec analog controls
+ block in the PRCM.
+
Example:
codec: codec@01c22c00 {
#sound-dai-cells = <0>;
@@ -28,3 +69,23 @@ codec: codec@01c22c00 {
dmas = <&dma 0 19>, <&dma 0 19>;
dma-names = "rx", "tx";
};
+
+codec: codec@01c22c00 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun6i-a31-codec";
+ reg = <0x01c22c00 0x98>;
+ interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_APB1_CODEC>, <&ccu CLK_CODEC>;
+ clock-names = "apb", "codec";
+ resets = <&ccu RST_APB1_CODEC>;
+ dmas = <&dma 15>, <&dma 15>;
+ dma-names = "rx", "tx";
+ allwinner,audio-routing =
+ "Headphone", "HP",
+ "Speaker", "LINEOUT",
+ "LINEIN", "Line In",
+ "MIC1", "MBIAS",
+ "MIC1", "Mic",
+ "MIC2", "HBIAS",
+ "MIC2", "Headset Mic";
+};
diff --git a/dts/Bindings/sound/sun8i-codec-analog.txt b/dts/Bindings/sound/sun8i-codec-analog.txt
new file mode 100644
index 0000000000..779b735781
--- /dev/null
+++ b/dts/Bindings/sound/sun8i-codec-analog.txt
@@ -0,0 +1,16 @@
+* Allwinner Codec Analog Controls
+
+Required properties:
+- compatible: must be one of the following compatibles:
+ - "allwinner,sun8i-a23-codec-analog"
+ - "allwinner,sun8i-h3-codec-analog"
+
+Required properties if not a sub-node of the PRCM node:
+- reg: must contain the registers location and length
+
+Example:
+prcm: prcm@01f01400 {
+ codec_analog: codec-analog {
+ compatible = "allwinner,sun8i-a23-codec-analog";
+ };
+};
diff --git a/dts/Bindings/sound/tlv320aic31xx.txt b/dts/Bindings/sound/tlv320aic31xx.txt
index 9340d2ddcc..6fbba562ea 100644
--- a/dts/Bindings/sound/tlv320aic31xx.txt
+++ b/dts/Bindings/sound/tlv320aic31xx.txt
@@ -12,6 +12,7 @@ Required properties:
"ti,tlv320aic3120" - TLV320AIC3120 (mono speaker amp, MiniDSP)
"ti,tlv320aic3111" - TLV320AIC3111 (stereo speaker amp, MiniDSP)
"ti,tlv320dac3100" - TLV320DAC3100 (no ADC, mono speaker amp, no MiniDSP)
+ "ti,tlv320dac3101" - TLV320DAC3101 (no ADC, stereo speaker amp, no MiniDSP)
- reg - <int> - I2C slave address
- HPVDD-supply, SPRVDD-supply, SPLVDD-supply, AVDD-supply, IOVDD-supply,
diff --git a/dts/Bindings/sound/wm8580.txt b/dts/Bindings/sound/wm8580.txt
index 7d9821f348..78fce9b149 100644
--- a/dts/Bindings/sound/wm8580.txt
+++ b/dts/Bindings/sound/wm8580.txt
@@ -1,10 +1,10 @@
-WM8580 audio CODEC
+WM8580 and WM8581 audio CODEC
This device supports I2C only.
Required properties:
- - compatible : "wlf,wm8580"
+ - compatible : "wlf,wm8580", "wlf,wm8581"
- reg : the I2C address of the device.
generated by cgit v1.2.3 (git 2.39.1) at 2024-04-18 10:39:27 +0000