diff options
Diffstat (limited to 'dts/Bindings/spi')
| -rw-r--r-- | dts/Bindings/spi/fsl-spi.txt | 8 | ||||
| -rw-r--r-- | dts/Bindings/spi/nuvoton,npcm-pspi.txt | 12 | ||||
| -rw-r--r-- | dts/Bindings/spi/spi-stm32.txt | 62 | ||||
| -rw-r--r-- | dts/Bindings/spi/spi_atmel.txt | 2 | ||||
| -rw-r--r-- | dts/Bindings/spi/st,stm32-spi.yaml | 105 |
5 files changed, 112 insertions, 77 deletions
diff --git a/dts/Bindings/spi/fsl-spi.txt b/dts/Bindings/spi/fsl-spi.txt index 411375eac5..0654380eb7 100644 --- a/dts/Bindings/spi/fsl-spi.txt +++ b/dts/Bindings/spi/fsl-spi.txt @@ -15,13 +15,13 @@ Required properties: - clock-frequency : input clock frequency to non FSL_SOC cores Optional properties: -- gpios : specifies the gpio pins to be used for chipselects. +- cs-gpios : specifies the gpio pins to be used for chipselects. The gpios will be referred to as reg = <index> in the SPI child nodes. If unspecified, a single SPI device without a chip select can be used. - fsl,spisel_boot : for the MPC8306 and MPC8309, specifies that the SPISEL_BOOT signal is used as chip select for a slave device. Use reg = <number of gpios> in the corresponding child node, i.e. 0 if - the gpios property is not present. + the cs-gpios property is not present. Example: spi@4c0 { @@ -31,8 +31,8 @@ Example: interrupts = <82 0>; interrupt-parent = <700>; mode = "cpu"; - gpios = <&gpio 18 1 // device reg=<0> - &gpio 19 1>; // device reg=<1> + cs-gpios = <&gpio 18 1 // device reg=<0> + &gpio 19 1>; // device reg=<1> }; diff --git a/dts/Bindings/spi/nuvoton,npcm-pspi.txt b/dts/Bindings/spi/nuvoton,npcm-pspi.txt index 1fd9a4406a..b98203ca65 100644 --- a/dts/Bindings/spi/nuvoton,npcm-pspi.txt +++ b/dts/Bindings/spi/nuvoton,npcm-pspi.txt @@ -12,6 +12,7 @@ Required properties: - clock-names: Should be "clk_apb5". - pinctrl-names : a pinctrl state named "default" must be defined. - pinctrl-0 : phandle referencing pin configuration of the device. + - resets : phandle to the reset control for this device. - cs-gpios: Specifies the gpio pins to be used for chipselects. See: Documentation/devicetree/bindings/spi/spi-bus.txt @@ -19,16 +20,6 @@ Optional properties: - clock-frequency : Input clock frequency to the PSPI block in Hz. Default is 25000000 Hz. -Aliases: -- All the SPI controller nodes should be represented in the aliases node using - the following format 'spi{n}' withe the correct numbered in "aliases" node. - -Example: - -aliases { - spi0 = &spi0; -}; - spi0: spi@f0200000 { compatible = "nuvoton,npcm750-pspi"; reg = <0xf0200000 0x1000>; @@ -39,5 +30,6 @@ spi0: spi@f0200000 { interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clk NPCM7XX_CLK_APB5>; clock-names = "clk_apb5"; + resets = <&rstc NPCM7XX_RESET_IPSRST2 NPCM7XX_RESET_PSPI1> cs-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>; }; diff --git a/dts/Bindings/spi/spi-stm32.txt b/dts/Bindings/spi/spi-stm32.txt deleted file mode 100644 index d82755c63e..0000000000 --- a/dts/Bindings/spi/spi-stm32.txt +++ /dev/null @@ -1,62 +0,0 @@ -STMicroelectronics STM32 SPI Controller - -The STM32 SPI controller is used to communicate with external devices using -the Serial Peripheral Interface. It supports full-duplex, half-duplex and -simplex synchronous serial communication with external devices. It supports -from 4 to 32-bit data size. Although it can be configured as master or slave, -only master is supported by the driver. - -Required properties: -- compatible: Should be one of: - "st,stm32h7-spi" - "st,stm32f4-spi" -- reg: Offset and length of the device's register set. -- interrupts: Must contain the interrupt id. -- clocks: Must contain an entry for spiclk (which feeds the internal clock - generator). -- #address-cells: Number of cells required to define a chip select address. -- #size-cells: Should be zero. - -Optional properties: -- resets: Must contain the phandle to the reset controller. -- A pinctrl state named "default" may be defined to set pins in mode of - operation for SPI transfer. -- dmas: DMA specifiers for tx and rx dma. DMA fifo mode must be used. See the - STM32 DMA bindings, Documentation/devicetree/bindings/dma/stm32-dma.txt. -- dma-names: DMA request names should include "tx" and "rx" if present. -- cs-gpios: list of GPIO chip selects. See the SPI bus bindings, - Documentation/devicetree/bindings/spi/spi-bus.txt - - -Child nodes represent devices on the SPI bus - See ../spi/spi-bus.txt - -Optional properties: -- st,spi-midi-ns: Only for STM32H7, (Master Inter-Data Idleness) minimum time - delay in nanoseconds inserted between two consecutive data - frames. - - -Example: - spi2: spi@40003800 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "st,stm32h7-spi"; - reg = <0x40003800 0x400>; - interrupts = <36>; - clocks = <&rcc SPI2_CK>; - resets = <&rcc 1166>; - dmas = <&dmamux1 0 39 0x400 0x01>, - <&dmamux1 1 40 0x400 0x01>; - dma-names = "rx", "tx"; - pinctrl-0 = <&spi2_pins_b>; - pinctrl-names = "default"; - cs-gpios = <&gpioa 11 0>; - - aardvark@0 { - compatible = "totalphase,aardvark"; - reg = <0>; - spi-max-frequency = <4000000>; - st,spi-midi-ns = <4000>; - }; - }; diff --git a/dts/Bindings/spi/spi_atmel.txt b/dts/Bindings/spi/spi_atmel.txt index f99c733d75..5bb4a8f1df 100644 --- a/dts/Bindings/spi/spi_atmel.txt +++ b/dts/Bindings/spi/spi_atmel.txt @@ -1,7 +1,7 @@ Atmel SPI device Required properties: -- compatible : should be "atmel,at91rm9200-spi". +- compatible : should be "atmel,at91rm9200-spi" or "microchip,sam9x60-spi". - reg: Address and length of the register set for the device - interrupts: Should contain spi interrupt - cs-gpios: chipselects (optional for SPI controller version >= 2 with the diff --git a/dts/Bindings/spi/st,stm32-spi.yaml b/dts/Bindings/spi/st,stm32-spi.yaml new file mode 100644 index 0000000000..f0d979664f --- /dev/null +++ b/dts/Bindings/spi/st,stm32-spi.yaml @@ -0,0 +1,105 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/spi/st,stm32-spi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STMicroelectronics STM32 SPI Controller bindings + +description: | + The STM32 SPI controller is used to communicate with external devices using + the Serial Peripheral Interface. It supports full-duplex, half-duplex and + simplex synchronous serial communication with external devices. It supports + from 4 to 32-bit data size. + +maintainers: + - Erwan Leray <erwan.leray@st.com> + - Fabrice Gasnier <fabrice.gasnier@st.com> + +allOf: + - $ref: "spi-controller.yaml#" + - if: + properties: + compatible: + contains: + const: st,stm32f4-spi + + then: + properties: + st,spi-midi-ns: false + +properties: + compatible: + enum: + - st,stm32f4-spi + - st,stm32h7-spi + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + interrupts: + maxItems: 1 + + resets: + maxItems: 1 + + dmas: + description: | + DMA specifiers for tx and rx dma. DMA fifo mode must be used. See + the STM32 DMA bindings Documentation/devicetree/bindings/dma/stm32-dma.txt. + items: + - description: rx DMA channel + - description: tx DMA channel + + dma-names: + items: + - const: rx + - const: tx + +patternProperties: + "^[a-zA-Z][a-zA-Z0-9,+\\-._]{0,63}@[0-9a-f]+$": + type: object + # SPI slave nodes must be children of the SPI master node and can + # contain the following properties. + properties: + st,spi-midi-ns: + description: | + Only for STM32H7, (Master Inter-Data Idleness) minimum time + delay in nanoseconds inserted between two consecutive data frames. + +required: + - compatible + - reg + - clocks + - interrupts + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/stm32mp1-clks.h> + #include <dt-bindings/reset/stm32mp1-resets.h> + spi@4000b000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32h7-spi"; + reg = <0x4000b000 0x400>; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc SPI2_K>; + resets = <&rcc SPI2_R>; + dmas = <&dmamux1 0 39 0x400 0x05>, + <&dmamux1 1 40 0x400 0x05>; + dma-names = "rx", "tx"; + cs-gpios = <&gpioa 11 0>; + + aardvark@0 { + compatible = "totalphase,aardvark"; + reg = <0>; + spi-max-frequency = <4000000>; + st,spi-midi-ns = <4000>; + }; + }; + +... |