diff options
Diffstat (limited to 'dts/Bindings/staging')
| -rw-r--r-- | dts/Bindings/staging/iio/adc/lpc32xx-adc.txt | 16 | ||||
| -rw-r--r-- | dts/Bindings/staging/iio/adc/mxs-lradc.txt | 47 | ||||
| -rw-r--r-- | dts/Bindings/staging/iio/adc/spear-adc.txt | 26 | ||||
| -rw-r--r-- | dts/Bindings/staging/imx-drm/fsl-imx-drm.txt | 82 | ||||
| -rw-r--r-- | dts/Bindings/staging/imx-drm/hdmi.txt | 58 | ||||
| -rw-r--r-- | dts/Bindings/staging/imx-drm/ldb.txt | 111 | ||||
| -rw-r--r-- | dts/Bindings/staging/xillybus.txt | 20 |
7 files changed, 360 insertions, 0 deletions
diff --git a/dts/Bindings/staging/iio/adc/lpc32xx-adc.txt b/dts/Bindings/staging/iio/adc/lpc32xx-adc.txt new file mode 100644 index 0000000000..b3629d3a9a --- /dev/null +++ b/dts/Bindings/staging/iio/adc/lpc32xx-adc.txt @@ -0,0 +1,16 @@ +* NXP LPC32xx SoC ADC controller + +Required properties: +- compatible: must be "nxp,lpc3220-adc" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: The ADC interrupt + +Example: + + adc@40048000 { + compatible = "nxp,lpc3220-adc"; + reg = <0x40048000 0x1000>; + interrupt-parent = <&mic>; + interrupts = <39 0>; + }; diff --git a/dts/Bindings/staging/iio/adc/mxs-lradc.txt b/dts/Bindings/staging/iio/adc/mxs-lradc.txt new file mode 100644 index 0000000000..ee05dc3906 --- /dev/null +++ b/dts/Bindings/staging/iio/adc/mxs-lradc.txt @@ -0,0 +1,47 @@ +* Freescale i.MX28 LRADC device driver + +Required properties: +- compatible: Should be "fsl,imx23-lradc" for i.MX23 SoC and "fsl,imx28-lradc" + for i.MX28 SoC +- reg: Address and length of the register set for the device +- interrupts: Should contain the LRADC interrupts + +Optional properties: +- fsl,lradc-touchscreen-wires: Number of wires used to connect the touchscreen + to LRADC. Valid value is either 4 or 5. If this + property is not present, then the touchscreen is + disabled. 5 wires is valid for i.MX28 SoC only. +- fsl,ave-ctrl: number of samples per direction to calculate an average value. + Allowed value is 1 ... 31, default is 4 +- fsl,ave-delay: delay between consecutive samples. Allowed value is + 1 ... 2047. It is used if 'fsl,ave-ctrl' > 1, counts at + 2 kHz and its default is 2 (= 1 ms) +- fsl,settling: delay between plate switch to next sample. Allowed value is + 1 ... 2047. It counts at 2 kHz and its default is + 10 (= 5 ms) + +Example for i.MX23 SoC: + + lradc@80050000 { + compatible = "fsl,imx23-lradc"; + reg = <0x80050000 0x2000>; + interrupts = <36 37 38 39 40 41 42 43 44>; + status = "okay"; + fsl,lradc-touchscreen-wires = <4>; + fsl,ave-ctrl = <4>; + fsl,ave-delay = <2>; + fsl,settling = <10>; + }; + +Example for i.MX28 SoC: + + lradc@80050000 { + compatible = "fsl,imx28-lradc"; + reg = <0x80050000 0x2000>; + interrupts = <10 14 15 16 17 18 19 20 21 22 23 24 25>; + status = "okay"; + fsl,lradc-touchscreen-wires = <5>; + fsl,ave-ctrl = <4>; + fsl,ave-delay = <2>; + fsl,settling = <10>; + }; diff --git a/dts/Bindings/staging/iio/adc/spear-adc.txt b/dts/Bindings/staging/iio/adc/spear-adc.txt new file mode 100644 index 0000000000..02ea23a63f --- /dev/null +++ b/dts/Bindings/staging/iio/adc/spear-adc.txt @@ -0,0 +1,26 @@ +* ST SPEAr ADC device driver + +Required properties: +- compatible: Should be "st,spear600-adc" +- reg: Address and length of the register set for the device +- interrupt-parent: Should be the phandle for the interrupt controller + that services interrupts for this device +- interrupts: Should contain the ADC interrupt +- sampling-frequency: Default sampling frequency + +Optional properties: +- vref-external: External voltage reference in milli-volts. If omitted + the internal voltage reference will be used. +- average-samples: Number of samples to generate an average value. If + omitted, single data conversion will be used. + +Examples: + + adc: adc@d8200000 { + compatible = "st,spear600-adc"; + reg = <0xd8200000 0x1000>; + interrupt-parent = <&vic1>; + interrupts = <6>; + sampling-frequency = <5000000>; + vref-external = <2500>; /* 2.5V VRef */ + }; diff --git a/dts/Bindings/staging/imx-drm/fsl-imx-drm.txt b/dts/Bindings/staging/imx-drm/fsl-imx-drm.txt new file mode 100644 index 0000000000..3be5ce7a96 --- /dev/null +++ b/dts/Bindings/staging/imx-drm/fsl-imx-drm.txt @@ -0,0 +1,82 @@ +Freescale i.MX DRM master device +================================ + +The freescale i.MX DRM master device is a virtual device needed to list all +IPU or other display interface nodes that comprise the graphics subsystem. + +Required properties: +- compatible: Should be "fsl,imx-display-subsystem" +- ports: Should contain a list of phandles pointing to display interface ports + of IPU devices + +example: + +display-subsystem { + compatible = "fsl,display-subsystem"; + ports = <&ipu_di0>; +}; + + +Freescale i.MX IPUv3 +==================== + +Required properties: +- compatible: Should be "fsl,<chip>-ipu" +- reg: should be register base and length as documented in the + datasheet +- interrupts: Should contain sync interrupt and error interrupt, + in this order. +- resets: phandle pointing to the system reset controller and + reset line index, see reset/fsl,imx-src.txt for details +Optional properties: +- port@[0-3]: Port nodes with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. + Ports 0 and 1 should correspond to CSI0 and CSI1, + ports 2 and 3 should correspond to DI0 and DI1, respectively. + +example: + +ipu: ipu@18000000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx53-ipu"; + reg = <0x18000000 0x080000000>; + interrupts = <11 10>; + resets = <&src 2>; + + ipu_di0: port@2 { + reg = <2>; + + ipu_di0_disp0: endpoint { + remote-endpoint = <&display_in>; + }; + }; +}; + +Parallel display support +======================== + +Required properties: +- compatible: Should be "fsl,imx-parallel-display" +Optional properties: +- interface_pix_fmt: How this display is connected to the + display interface. Currently supported types: "rgb24", "rgb565", "bgr666" +- edid: verbatim EDID data block describing attached display. +- ddc: phandle describing the i2c bus handling the display data + channel +- port: A port node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. + +example: + +display@di0 { + compatible = "fsl,imx-parallel-display"; + edid = [edid-data]; + interface-pix-fmt = "rgb24"; + + port { + display_in: endpoint { + remote-endpoint = <&ipu_di0_disp0>; + }; + }; +}; diff --git a/dts/Bindings/staging/imx-drm/hdmi.txt b/dts/Bindings/staging/imx-drm/hdmi.txt new file mode 100644 index 0000000000..1b756cf9af --- /dev/null +++ b/dts/Bindings/staging/imx-drm/hdmi.txt @@ -0,0 +1,58 @@ +Device-Tree bindings for HDMI Transmitter + +HDMI Transmitter +================ + +The HDMI Transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP +with accompanying PHY IP. + +Required properties: + - #address-cells : should be <1> + - #size-cells : should be <0> + - compatible : should be "fsl,imx6q-hdmi" or "fsl,imx6dl-hdmi". + - gpr : should be <&gpr>. + The phandle points to the iomuxc-gpr region containing the HDMI + multiplexer control register. + - clocks, clock-names : phandles to the HDMI iahb and isrf clocks, as described + in Documentation/devicetree/bindings/clock/clock-bindings.txt and + Documentation/devicetree/bindings/clock/imx6q-clock.txt. + - port@[0-4]: Up to four port nodes with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt, + corresponding to the four inputs to the HDMI multiplexer. + +Optional properties: + - ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing + +example: + + gpr: iomuxc-gpr@020e0000 { + /* ... */ + }; + + hdmi: hdmi@0120000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx6q-hdmi"; + reg = <0x00120000 0x9000>; + interrupts = <0 115 0x04>; + gpr = <&gpr>; + clocks = <&clks 123>, <&clks 124>; + clock-names = "iahb", "isfr"; + ddc-i2c-bus = <&i2c2>; + + port@0 { + reg = <0>; + + hdmi_mux_0: endpoint { + remote-endpoint = <&ipu1_di0_hdmi>; + }; + }; + + port@1 { + reg = <1>; + + hdmi_mux_1: endpoint { + remote-endpoint = <&ipu1_di1_hdmi>; + }; + }; + }; diff --git a/dts/Bindings/staging/imx-drm/ldb.txt b/dts/Bindings/staging/imx-drm/ldb.txt new file mode 100644 index 0000000000..578a1fca36 --- /dev/null +++ b/dts/Bindings/staging/imx-drm/ldb.txt @@ -0,0 +1,111 @@ +Device-Tree bindings for LVDS Display Bridge (ldb) + +LVDS Display Bridge +=================== + +The LVDS Display Bridge device tree node contains up to two lvds-channel +nodes describing each of the two LVDS encoder channels of the bridge. + +Required properties: + - #address-cells : should be <1> + - #size-cells : should be <0> + - compatible : should be "fsl,imx53-ldb" or "fsl,imx6q-ldb". + Both LDB versions are similar, but i.MX6 has an additional + multiplexer in the front to select any of the four IPU display + interfaces as input for each LVDS channel. + - gpr : should be <&gpr> on i.MX53 and i.MX6q. + The phandle points to the iomuxc-gpr region containing the LVDS + control register. +- clocks, clock-names : phandles to the LDB divider and selector clocks and to + the display interface selector clocks, as described in + Documentation/devicetree/bindings/clock/clock-bindings.txt + The following clocks are expected on i.MX53: + "di0_pll" - LDB LVDS channel 0 mux + "di1_pll" - LDB LVDS channel 1 mux + "di0" - LDB LVDS channel 0 gate + "di1" - LDB LVDS channel 1 gate + "di0_sel" - IPU1 DI0 mux + "di1_sel" - IPU1 DI1 mux + On i.MX6q the following additional clocks are needed: + "di2_sel" - IPU2 DI0 mux + "di3_sel" - IPU2 DI1 mux + The needed clock numbers for each are documented in + Documentation/devicetree/bindings/clock/imx5-clock.txt, and in + Documentation/devicetree/bindings/clock/imx6q-clock.txt. + +Optional properties: + - pinctrl-names : should be "default" on i.MX53, not used on i.MX6q + - pinctrl-0 : a phandle pointing to LVDS pin settings on i.MX53, + not used on i.MX6q + - fsl,dual-channel : boolean. if it exists, only LVDS channel 0 should + be configured - one input will be distributed on both outputs in dual + channel mode + +LVDS Channel +============ + +Each LVDS Channel has to contain a display-timings node that describes the +video timings for the connected LVDS display. For detailed information, also +have a look at Documentation/devicetree/bindings/video/display-timing.txt. + +Required properties: + - reg : should be <0> or <1> + - fsl,data-mapping : should be "spwg" or "jeida" + This describes how the color bits are laid out in the + serialized LVDS signal. + - fsl,data-width : should be <18> or <24> + - port: A port node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. + On i.MX6, there should be four ports (port@[0-3]) that correspond + to the four LVDS multiplexer inputs. + +example: + +gpr: iomuxc-gpr@53fa8000 { + /* ... */ +}; + +ldb: ldb@53fa8008 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx53-ldb"; + gpr = <&gpr>; + clocks = <&clks 122>, <&clks 120>, + <&clks 115>, <&clks 116>, + <&clks 123>, <&clks 85>; + clock-names = "di0_pll", "di1_pll", + "di0_sel", "di1_sel", + "di0", "di1"; + + lvds-channel@0 { + reg = <0>; + fsl,data-mapping = "spwg"; + fsl,data-width = <24>; + + display-timings { + /* ... */ + }; + + port { + lvds0_in: endpoint { + remote-endpoint = <&ipu_di0_lvds0>; + }; + }; + }; + + lvds-channel@1 { + reg = <1>; + fsl,data-mapping = "spwg"; + fsl,data-width = <24>; + + display-timings { + /* ... */ + }; + + port { + lvds1_in: endpoint { + remote-endpoint = <&ipu_di1_lvds1>; + }; + }; + }; +}; diff --git a/dts/Bindings/staging/xillybus.txt b/dts/Bindings/staging/xillybus.txt new file mode 100644 index 0000000000..9e316dc2e4 --- /dev/null +++ b/dts/Bindings/staging/xillybus.txt @@ -0,0 +1,20 @@ +* Xillybus driver for generic FPGA interface + +Required properties: +- compatible: Should be "xillybus,xillybus-1.00.a" +- reg: Address and length of the register set for the device +- interrupts: Contains one interrupt node, typically consisting of three cells. +- interrupt-parent: the phandle for the interrupt controller that + services interrupts for this device. + +Optional properties: +- dma-coherent: Present if DMA operations are coherent + +Example: + + xillybus@ff200400 { + compatible = "xillybus,xillybus-1.00.a"; + reg = < 0xff200400 0x00000080 >; + interrupts = < 0 40 1 >; + interrupt-parent = <&intc>; + } ; |