diff options
Diffstat (limited to 'dts/Bindings/staging')
| -rw-r--r-- | dts/Bindings/staging/imx-drm/fsl-imx-drm.txt | 83 | ||||
| -rw-r--r-- | dts/Bindings/staging/imx-drm/hdmi.txt | 58 | ||||
| -rw-r--r-- | dts/Bindings/staging/imx-drm/ldb.txt | 122 |
3 files changed, 0 insertions, 263 deletions
diff --git a/dts/Bindings/staging/imx-drm/fsl-imx-drm.txt b/dts/Bindings/staging/imx-drm/fsl-imx-drm.txt deleted file mode 100644 index e75f0e549f..0000000000 --- a/dts/Bindings/staging/imx-drm/fsl-imx-drm.txt +++ /dev/null @@ -1,83 +0,0 @@ -Freescale i.MX DRM master device -================================ - -The freescale i.MX DRM master device is a virtual device needed to list all -IPU or other display interface nodes that comprise the graphics subsystem. - -Required properties: -- compatible: Should be "fsl,imx-display-subsystem" -- ports: Should contain a list of phandles pointing to display interface ports - of IPU devices - -example: - -display-subsystem { - compatible = "fsl,display-subsystem"; - ports = <&ipu_di0>; -}; - - -Freescale i.MX IPUv3 -==================== - -Required properties: -- compatible: Should be "fsl,<chip>-ipu" -- reg: should be register base and length as documented in the - datasheet -- interrupts: Should contain sync interrupt and error interrupt, - in this order. -- resets: phandle pointing to the system reset controller and - reset line index, see reset/fsl,imx-src.txt for details -Optional properties: -- port@[0-3]: Port nodes with endpoint definitions as defined in - Documentation/devicetree/bindings/media/video-interfaces.txt. - Ports 0 and 1 should correspond to CSI0 and CSI1, - ports 2 and 3 should correspond to DI0 and DI1, respectively. - -example: - -ipu: ipu@18000000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,imx53-ipu"; - reg = <0x18000000 0x080000000>; - interrupts = <11 10>; - resets = <&src 2>; - - ipu_di0: port@2 { - reg = <2>; - - ipu_di0_disp0: endpoint { - remote-endpoint = <&display_in>; - }; - }; -}; - -Parallel display support -======================== - -Required properties: -- compatible: Should be "fsl,imx-parallel-display" -Optional properties: -- interface_pix_fmt: How this display is connected to the - display interface. Currently supported types: "rgb24", "rgb565", "bgr666" - and "lvds666". -- edid: verbatim EDID data block describing attached display. -- ddc: phandle describing the i2c bus handling the display data - channel -- port: A port node with endpoint definitions as defined in - Documentation/devicetree/bindings/media/video-interfaces.txt. - -example: - -display@di0 { - compatible = "fsl,imx-parallel-display"; - edid = [edid-data]; - interface-pix-fmt = "rgb24"; - - port { - display_in: endpoint { - remote-endpoint = <&ipu_di0_disp0>; - }; - }; -}; diff --git a/dts/Bindings/staging/imx-drm/hdmi.txt b/dts/Bindings/staging/imx-drm/hdmi.txt deleted file mode 100644 index 1b756cf9af..0000000000 --- a/dts/Bindings/staging/imx-drm/hdmi.txt +++ /dev/null @@ -1,58 +0,0 @@ -Device-Tree bindings for HDMI Transmitter - -HDMI Transmitter -================ - -The HDMI Transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP -with accompanying PHY IP. - -Required properties: - - #address-cells : should be <1> - - #size-cells : should be <0> - - compatible : should be "fsl,imx6q-hdmi" or "fsl,imx6dl-hdmi". - - gpr : should be <&gpr>. - The phandle points to the iomuxc-gpr region containing the HDMI - multiplexer control register. - - clocks, clock-names : phandles to the HDMI iahb and isrf clocks, as described - in Documentation/devicetree/bindings/clock/clock-bindings.txt and - Documentation/devicetree/bindings/clock/imx6q-clock.txt. - - port@[0-4]: Up to four port nodes with endpoint definitions as defined in - Documentation/devicetree/bindings/media/video-interfaces.txt, - corresponding to the four inputs to the HDMI multiplexer. - -Optional properties: - - ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing - -example: - - gpr: iomuxc-gpr@020e0000 { - /* ... */ - }; - - hdmi: hdmi@0120000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,imx6q-hdmi"; - reg = <0x00120000 0x9000>; - interrupts = <0 115 0x04>; - gpr = <&gpr>; - clocks = <&clks 123>, <&clks 124>; - clock-names = "iahb", "isfr"; - ddc-i2c-bus = <&i2c2>; - - port@0 { - reg = <0>; - - hdmi_mux_0: endpoint { - remote-endpoint = <&ipu1_di0_hdmi>; - }; - }; - - port@1 { - reg = <1>; - - hdmi_mux_1: endpoint { - remote-endpoint = <&ipu1_di1_hdmi>; - }; - }; - }; diff --git a/dts/Bindings/staging/imx-drm/ldb.txt b/dts/Bindings/staging/imx-drm/ldb.txt deleted file mode 100644 index 443bcb6134..0000000000 --- a/dts/Bindings/staging/imx-drm/ldb.txt +++ /dev/null @@ -1,122 +0,0 @@ -Device-Tree bindings for LVDS Display Bridge (ldb) - -LVDS Display Bridge -=================== - -The LVDS Display Bridge device tree node contains up to two lvds-channel -nodes describing each of the two LVDS encoder channels of the bridge. - -Required properties: - - #address-cells : should be <1> - - #size-cells : should be <0> - - compatible : should be "fsl,imx53-ldb" or "fsl,imx6q-ldb". - Both LDB versions are similar, but i.MX6 has an additional - multiplexer in the front to select any of the four IPU display - interfaces as input for each LVDS channel. - - gpr : should be <&gpr> on i.MX53 and i.MX6q. - The phandle points to the iomuxc-gpr region containing the LVDS - control register. -- clocks, clock-names : phandles to the LDB divider and selector clocks and to - the display interface selector clocks, as described in - Documentation/devicetree/bindings/clock/clock-bindings.txt - The following clocks are expected on i.MX53: - "di0_pll" - LDB LVDS channel 0 mux - "di1_pll" - LDB LVDS channel 1 mux - "di0" - LDB LVDS channel 0 gate - "di1" - LDB LVDS channel 1 gate - "di0_sel" - IPU1 DI0 mux - "di1_sel" - IPU1 DI1 mux - On i.MX6q the following additional clocks are needed: - "di2_sel" - IPU2 DI0 mux - "di3_sel" - IPU2 DI1 mux - The needed clock numbers for each are documented in - Documentation/devicetree/bindings/clock/imx5-clock.txt, and in - Documentation/devicetree/bindings/clock/imx6q-clock.txt. - -Optional properties: - - pinctrl-names : should be "default" on i.MX53, not used on i.MX6q - - pinctrl-0 : a phandle pointing to LVDS pin settings on i.MX53, - not used on i.MX6q - - fsl,dual-channel : boolean. if it exists, only LVDS channel 0 should - be configured - one input will be distributed on both outputs in dual - channel mode - -LVDS Channel -============ - -Each LVDS Channel has to contain a display-timings node that describes the -video timings for the connected LVDS display. For detailed information, also -have a look at Documentation/devicetree/bindings/video/display-timing.txt. - -Required properties: - - reg : should be <0> or <1> - - fsl,data-mapping : should be "spwg" or "jeida" - This describes how the color bits are laid out in the - serialized LVDS signal. - - fsl,data-width : should be <18> or <24> - - port: A port node with endpoint definitions as defined in - Documentation/devicetree/bindings/media/video-interfaces.txt. - On i.MX5, the internal two-input-multiplexer is used. - Due to hardware limitations, only one port (port@[0,1]) - can be used for each channel (lvds-channel@[0,1], respectively) - On i.MX6, there should be four ports (port@[0-3]) that correspond - to the four LVDS multiplexer inputs. - -example: - -gpr: iomuxc-gpr@53fa8000 { - /* ... */ -}; - -ldb: ldb@53fa8008 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,imx53-ldb"; - gpr = <&gpr>; - clocks = <&clks 122>, <&clks 120>, - <&clks 115>, <&clks 116>, - <&clks 123>, <&clks 85>; - clock-names = "di0_pll", "di1_pll", - "di0_sel", "di1_sel", - "di0", "di1"; - - lvds-channel@0 { - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - fsl,data-mapping = "spwg"; - fsl,data-width = <24>; - - display-timings { - /* ... */ - }; - - port@0 { - reg = <0>; - - lvds0_in: endpoint { - remote-endpoint = <&ipu_di0_lvds0>; - }; - }; - }; - - lvds-channel@1 { - #address-cells = <1>; - #size-cells = <0>; - reg = <1>; - fsl,data-mapping = "spwg"; - fsl,data-width = <24>; - - display-timings { - /* ... */ - }; - - port@1 { - reg = <1>; - - lvds1_in: endpoint { - remote-endpoint = <&ipu_di1_lvds1>; - }; - }; - }; -}; |