diff options
Diffstat (limited to 'dts/Bindings/ufs')
| -rw-r--r-- | dts/Bindings/ufs/ufs-hisi.txt | 41 | ||||
| -rw-r--r-- | dts/Bindings/ufs/ufshcd-pltfrm.txt | 10 |
2 files changed, 48 insertions, 3 deletions
diff --git a/dts/Bindings/ufs/ufs-hisi.txt b/dts/Bindings/ufs/ufs-hisi.txt new file mode 100644 index 0000000000..a48c448173 --- /dev/null +++ b/dts/Bindings/ufs/ufs-hisi.txt @@ -0,0 +1,41 @@ +* Hisilicon Universal Flash Storage (UFS) Host Controller + +UFS nodes are defined to describe on-chip UFS hardware macro. +Each UFS Host Controller should have its own node. + +Required properties: +- compatible : compatible list, contains one of the following - + "hisilicon,hi3660-ufs", "jedec,ufs-1.1" for hisi ufs + host controller present on Hi36xx chipset. +- reg : should contain UFS register address space & UFS SYS CTRL register address, +- interrupt-parent : interrupt device +- interrupts : interrupt number +- clocks : List of phandle and clock specifier pairs +- clock-names : List of clock input name strings sorted in the same + order as the clocks property. "ref_clk", "phy_clk" is optional +- freq-table-hz : Array of <min max> operating frequencies stored in the same + order as the clocks property. If this property is not + defined or a value in the array is "0" then it is assumed + that the frequency is set by the parent clock or a + fixed rate clock source. +- resets : describe reset node register +- reset-names : reset node register, the "rst" corresponds to reset the whole UFS IP. + +Example: + + ufs: ufs@ff3b0000 { + compatible = "hisilicon,hi3660-ufs", "jedec,ufs-1.1"; + /* 0: HCI standard */ + /* 1: UFS SYS CTRL */ + reg = <0x0 0xff3b0000 0x0 0x1000>, + <0x0 0xff3b1000 0x0 0x1000>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 278 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&crg_ctrl HI3660_CLK_GATE_UFSIO_REF>, + <&crg_ctrl HI3660_CLK_GATE_UFSPHY_CFG>; + clock-names = "ref_clk", "phy_clk"; + freq-table-hz = <0 0>, <0 0>; + /* offset: 0x84; bit: 12 */ + resets = <&crg_rst 0x84 12>; + reset-names = "rst"; + }; diff --git a/dts/Bindings/ufs/ufshcd-pltfrm.txt b/dts/Bindings/ufs/ufshcd-pltfrm.txt index c39dfef76a..2df00524bd 100644 --- a/dts/Bindings/ufs/ufshcd-pltfrm.txt +++ b/dts/Bindings/ufs/ufshcd-pltfrm.txt @@ -41,6 +41,8 @@ Optional properties: -lanes-per-direction : number of lanes available per direction - either 1 or 2. Note that it is assume same number of lanes is used both directions at once. If not specified, default is 2 lanes per direction. +- resets : reset node register +- reset-names : describe reset node register, the "rst" corresponds to reset the whole UFS IP. Note: If above properties are not defined it can be assumed that the supply regulators or clocks are always on. @@ -61,9 +63,11 @@ Example: vccq-max-microamp = 200000; vccq2-max-microamp = 200000; - clocks = <&core 0>, <&ref 0>, <&iface 0>; - clock-names = "core_clk", "ref_clk", "iface_clk"; - freq-table-hz = <100000000 200000000>, <0 0>, <0 0>; + clocks = <&core 0>, <&ref 0>, <&phy 0>, <&iface 0>; + clock-names = "core_clk", "ref_clk", "phy_clk", "iface_clk"; + freq-table-hz = <100000000 200000000>, <0 0>, <0 0>, <0 0>; + resets = <&reset 0 1>; + reset-names = "rst"; phys = <&ufsphy1>; phy-names = "ufsphy"; }; |