summaryrefslogtreecommitdiffstats
path: root/dts/Bindings/usb/amlogic,dwc3.txt
diff options
context:
space:
mode:
Diffstat (limited to 'dts/Bindings/usb/amlogic,dwc3.txt')
-rw-r--r--dts/Bindings/usb/amlogic,dwc3.txt88
1 files changed, 88 insertions, 0 deletions
diff --git a/dts/Bindings/usb/amlogic,dwc3.txt b/dts/Bindings/usb/amlogic,dwc3.txt
index 9a8b631..b9f04e6 100644
--- a/dts/Bindings/usb/amlogic,dwc3.txt
+++ b/dts/Bindings/usb/amlogic,dwc3.txt
@@ -40,3 +40,91 @@ Example device nodes:
phy-names = "usb2-phy", "usb3-phy";
};
};
+
+Amlogic Meson G12A DWC3 USB SoC Controller Glue
+
+The Amlogic G12A embeds a DWC3 USB IP Core configured for USB2 and USB3
+in host-only mode, and a DWC2 IP Core configured for USB2 peripheral mode
+only.
+
+A glue connects the DWC3 core to USB2 PHYs and optionnaly to an USB3 PHY.
+
+One of the USB2 PHY can be re-routed in peripheral mode to a DWC2 USB IP.
+
+The DWC3 Glue controls the PHY routing and power, an interrupt line is
+connected to the Glue to serve as OTG ID change detection.
+
+Required properties:
+- compatible: Should be "amlogic,meson-g12a-usb-ctrl"
+- clocks: a handle for the "USB" clock
+- resets: a handle for the shared "USB" reset line
+- reg: The base address and length of the registers
+- interrupts: the interrupt specifier for the OTG detection
+- phys: handle to used PHYs on the system
+ - a <0> phandle can be used if a PHY is not used
+- phy-names: names of the used PHYs on the system :
+ - "usb2-phy0" for USB2 PHY0 if USBHOST_A port is used
+ - "usb2-phy1" for USB2 PHY1 if USBOTG_B port is used
+ - "usb3-phy0" for USB3 PHY if USB3_0 is used
+- dr_mode: should be "host", "peripheral", or "otg" depending on
+ the usage and configuration of the OTG Capable port.
+ - "host" and "peripheral" means a fixed Host or Device only connection
+ - "otg" means the port can be used as both Host or Device and
+ be switched automatically using the OTG ID pin.
+
+Optional properties:
+- vbus-supply: should be a phandle to the regulator controlling the VBUS
+ power supply when used in OTG switchable mode
+
+Required child nodes:
+
+A child node must exist to represent the core DWC3 IP block. The name of
+the node is not important. The content of the node is defined in dwc3.txt.
+
+A child node must exist to represent the core DWC2 IP block. The name of
+the node is not important. The content of the node is defined in dwc2.txt.
+
+PHY documentation is provided in the following places:
+- Documentation/devicetree/bindings/phy/meson-g12a-usb2-phy.txt
+- Documentation/devicetree/bindings/phy/meson-g12a-usb3-pcie-phy.txt
+
+Example device nodes:
+ usb: usb@ffe09000 {
+ compatible = "amlogic,meson-g12a-usb-ctrl";
+ reg = <0x0 0xffe09000 0x0 0xa0>;
+ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ clocks = <&clkc CLKID_USB>;
+ resets = <&reset RESET_USB>;
+
+ dr_mode = "otg";
+
+ phys = <&usb2_phy0>, <&usb2_phy1>,
+ <&usb3_pcie_phy PHY_TYPE_USB3>;
+ phy-names = "usb2-phy0", "usb2-phy1", "usb3-phy0";
+
+ dwc2: usb@ff400000 {
+ compatible = "amlogic,meson-g12a-usb", "snps,dwc2";
+ reg = <0x0 0xff400000 0x0 0x40000>;
+ interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clkc CLKID_USB1_DDR_BRIDGE>;
+ clock-names = "ddr";
+ phys = <&usb2_phy1>;
+ dr_mode = "peripheral";
+ g-rx-fifo-size = <192>;
+ g-np-tx-fifo-size = <128>;
+ g-tx-fifo-size = <128 128 16 16 16>;
+ };
+
+ dwc3: usb@ff500000 {
+ compatible = "snps,dwc3";
+ reg = <0x0 0xff500000 0x0 0x100000>;
+ interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+ dr_mode = "host";
+ snps,dis_u2_susphy_quirk;
+ snps,quirk-frame-length-adjustment;
+ };
+ };