1 files changed, 0 insertions, 104 deletions
diff --git a/dts/Bindings/usb/qcom,dwc3.txt b/dts/Bindings/usb/qcom,dwc3.txt
deleted file mode 100644
index cb695aa3fb..0000000000
--- a/dts/Bindings/usb/qcom,dwc3.txt
+++ /dev/null
@@ -1,104 +0,0 @@
-Qualcomm SuperSpeed DWC3 USB SoC controller
-
-Required properties:
-- compatible:		Compatible list, contains
-			"qcom,dwc3"
-			"qcom,msm8996-dwc3" for msm8996 SOC.
-			"qcom,msm8998-dwc3" for msm8998 SOC.
-			"qcom,sdm845-dwc3" for sdm845 SOC.
-- reg:			Offset and length of register set for QSCRATCH wrapper
-- power-domains:	specifies a phandle to PM domain provider node
-- clocks:		A list of phandle + clock-specifier pairs for the
-				clocks listed in clock-names
-- clock-names:		Should contain the following:
-  "core"		Master/Core clock, have to be >= 125 MHz for SS
-				operation and >= 60MHz for HS operation
-  "mock_utmi"		Mock utmi clock needed for ITP/SOF generation in
-				host mode. Its frequency should be 19.2MHz.
-  "sleep"		Sleep clock, used for wakeup when USB3 core goes
-				into low power mode (U3).
-
-Optional clocks:
-  "iface"		System bus AXI clock.
-			Not present on "qcom,msm8996-dwc3" compatible.
-  "cfg_noc"		System Config NOC clock.
-			Not present on "qcom,msm8996-dwc3" compatible.
-- assigned-clocks:	Should be:
-				MOCK_UTMI_CLK
-				MASTER_CLK
-- assigned-clock-rates: Should be:
-                                19.2Mhz (192000000) for MOCK_UTMI_CLK
-                                >=125Mhz (125000000) for MASTER_CLK in SS mode
-                                >=60Mhz (60000000) for MASTER_CLK in HS mode
-
-Optional properties:
-- resets:		Phandle to reset control that resets core and wrapper.
-- interrupts:		specifies interrupts from controller wrapper used
-			to wakeup from low power/susepnd state.	Must contain
-			one or more entry for interrupt-names property
-- interrupt-names:	Must include the following entries:
-			- "hs_phy_irq": The interrupt that is asserted when a
-			   wakeup event is received on USB2 bus
-			- "ss_phy_irq": The interrupt that is asserted when a
-			   wakeup event is received on USB3 bus
-			- "dm_hs_phy_irq" and "dp_hs_phy_irq": Separate
-			   interrupts for any wakeup event on DM and DP lines
-- qcom,select-utmi-as-pipe-clk: if present, disable USB3 pipe_clk requirement.
-				Used when dwc3 operates without SSPHY and only
-				HS/FS/LS modes are supported.
-
-Required child node:
-A child node must exist to represent the core DWC3 IP block. The name of
-the node is not important. The content of the node is defined in dwc3.txt.
-
-Phy documentation is provided in the following places:
-Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt   - USB3 QMP PHY
-Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt - USB2 QUSB2 PHY
-
-Example device nodes:
-
-		hs_phy: phy@100f8800 {
-			compatible = "qcom,qusb2-v2-phy";
-			...
-		};
-
-		ss_phy: phy@100f8830 {
-			compatible = "qcom,qmp-v3-usb3-phy";
-			...
-		};
-
-		usb3_0: usb30@a6f8800 {
-			compatible = "qcom,dwc3";
-			reg = <0xa6f8800 0x400>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-
-			interrupts = <0 131 0>, <0 486 0>, <0 488 0>, <0 489 0>;
-			interrupt-names = "hs_phy_irq", "ss_phy_irq",
-				  "dm_hs_phy_irq", "dp_hs_phy_irq";
-
-			clocks = <&gcc GCC_USB30_PRIM_MASTER_CLK>,
-				<&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
-				<&gcc GCC_USB30_PRIM_SLEEP_CLK>;
-			clock-names = "core", "mock_utmi", "sleep";
-
-			assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
-					  <&gcc GCC_USB30_PRIM_MASTER_CLK>;
-			assigned-clock-rates = <19200000>, <133000000>;
-
-			resets = <&gcc GCC_USB30_PRIM_BCR>;
-			reset-names = "core_reset";
-			power-domains = <&gcc USB30_PRIM_GDSC>;
-			qcom,select-utmi-as-pipe-clk;
-
-			dwc3@10000000 {
-				compatible = "snps,dwc3";
-				reg = <0x10000000 0xcd00>;
-				interrupts = <0 205 0x4>;
-				phys = <&hs_phy>, <&ss_phy>;
-				phy-names = "usb2-phy", "usb3-phy";
-				dr_mode = "host";
-			};
-		};
-