diff options
Diffstat (limited to 'dts/Bindings/usb/snps,dwc3.yaml')
| -rw-r--r-- | dts/Bindings/usb/snps,dwc3.yaml | 147 |
1 files changed, 142 insertions, 5 deletions
diff --git a/dts/Bindings/usb/snps,dwc3.yaml b/dts/Bindings/usb/snps,dwc3.yaml index 25ac2c93dc..203a1eb666 100644 --- a/dts/Bindings/usb/snps,dwc3.yaml +++ b/dts/Bindings/usb/snps,dwc3.yaml @@ -36,20 +36,23 @@ properties: - const: synopsys,dwc3 deprecated: true + reg: + maxItems: 1 + interrupts: description: It's either a single common DWC3 interrupt (dwc_usb3) or individual interrupts for the host, gadget and DRD modes. minItems: 1 - maxItems: 3 + maxItems: 4 interrupt-names: minItems: 1 - maxItems: 3 + maxItems: 4 oneOf: - const: dwc_usb3 - items: - enum: [host, peripheral, otg] + enum: [host, peripheral, otg, wakeup] clocks: description: @@ -65,6 +68,15 @@ properties: - enum: [bus_early, ref, suspend] - true + dma-coherent: true + + extcon: + maxItems: 1 + deprecated: true + + iommus: + maxItems: 1 + usb-phy: minItems: 1 items: @@ -83,6 +95,16 @@ properties: - usb2-phy - usb3-phy + power-domains: + description: + The DWC3 has 2 power-domains. The power management unit (PMU) and + everything else. The PMU is typically always powered and may not have an + entry. + minItems: 1 + items: + - description: Core + - description: Power management unit + resets: minItems: 1 @@ -214,6 +236,11 @@ properties: When set, all SuperSpeed bus instances in park mode are disabled. type: boolean + snps,parkmode-disable-hs-quirk: + description: + When set, all HighSpeed bus instances in park mode are disabled. + type: boolean + snps,dis_metastability_quirk: description: When set, disable metastability workaround. CAUTION! Use only if you are @@ -226,6 +253,26 @@ properties: avoid -EPROTO errors with usbhid on some devices (Hikey 970). type: boolean + snps,gfladj-refclk-lpm-sel-quirk: + description: + When set, run the SOF/ITP counter based on ref_clk. + type: boolean + + snps,resume-hs-terminations: + description: + Fix the issue of HS terminations CRC error on resume by enabling this + quirk. When set, all the termsel, xcvrsel, opmode becomes 0 during end + of resume. This option is to support certain legacy ULPI PHYs. + type: boolean + + snps,ulpi-ext-vbus-drv: + description: + Some ULPI USB PHY does not support internal VBUS supply, and driving + the CPEN pin, requires the configuration of the ulpi DRVVBUSEXTERNAL + bit. When set, the xhci host will configure the USB2 PHY drives VBUS + with an external supply. + type: boolean + snps,is-utmi-l1-suspend: description: True when DWC3 asserts output signal utmi_l1_suspend_n, false when @@ -240,7 +287,7 @@ properties: description: High-Speed PHY interface selection between UTMI+ and ULPI when the DWC_USB3_HSPHY_INTERFACE has value 3. - $ref: /schemas/types.yaml#/definitions/uint8 + $ref: /schemas/types.yaml#/definitions/string enum: [utmi, ulpi] snps,quirk-frame-length-adjustment: @@ -257,8 +304,67 @@ properties: Value for REFCLKPER field of GUCTL register for reference clock period in nanoseconds, when the hardware set default does not match the actual clock. + + This binding is deprecated. Instead, provide an appropriate reference clock. + minimum: 8 + maximum: 62 + deprecated: true + + snps,rx-thr-num-pkt: + description: + USB RX packet threshold count. In host mode, this field specifies + the space that must be available in the RX FIFO before the core can + start the corresponding USB RX transaction (burst). + In device mode, this field specifies the space that must be + available in the RX FIFO before the core can send ERDY for a + flow-controlled endpoint. It is only used for SuperSpeed. + The valid values for this field are from 1 to 15. (DWC3 SuperSpeed + USB 3.0 Controller Databook) + $ref: /schemas/types.yaml#/definitions/uint8 + minimum: 1 + maximum: 15 + + snps,rx-max-burst: + description: + Max USB RX burst size. In host mode, this field specifies the + Maximum Bulk IN burst the DWC_usb3 core can perform. When the system + bus is slower than the USB, RX FIFO can overrun during a long burst. + You can program a smaller value to this field to limit the RX burst + size that the core can perform. It only applies to SS Bulk, + Isochronous, and Interrupt IN endpoints in the host mode. + In device mode, this field specifies the NUMP value that is sent in + ERDY for an OUT endpoint. + The valid values for this field are from 1 to 16. (DWC3 SuperSpeed + USB 3.0 Controller Databook) + $ref: /schemas/types.yaml#/definitions/uint8 + minimum: 1 + maximum: 16 + + snps,tx-thr-num-pkt: + description: + USB TX packet threshold count. This field specifies the number of + packets that must be in the TXFIFO before the core can start + transmission for the corresponding USB transaction (burst). + This count is valid in both host and device modes. It is only used + for SuperSpeed operation. + Valid values are from 1 to 15. (DWC3 SuperSpeed USB 3.0 Controller + Databook) + $ref: /schemas/types.yaml#/definitions/uint8 + minimum: 1 + maximum: 15 + + snps,tx-max-burst: + description: + Max USB TX burst size. When the system bus is slower than the USB, + TX FIFO can underrun during a long burst. Program a smaller value + to this field to limit the TX burst size that the core can execute. + In Host mode, it only applies to SS Bulk, Isochronous, and Interrupt + OUT endpoints. This value is not used in device mode. + Valid values are from 1 to 16. (DWC3 SuperSpeed USB 3.0 Controller + Databook) + $ref: /schemas/types.yaml#/definitions/uint8 minimum: 1 - maximum: 0x3ff + maximum: 16 snps,rx-thr-num-pkt-prd: description: @@ -326,6 +432,37 @@ properties: items: enum: [1, 4, 8, 16, 32, 64, 128, 256] + num-hc-interrupters: + maximum: 8 + default: 1 + + port: + $ref: /schemas/graph.yaml#/properties/port + description: + This port is used with the 'usb-role-switch' property to connect the + dwc3 to type C connector. + + ports: + $ref: /schemas/graph.yaml#/properties/ports + description: + Those ports should be used with any connector to the data bus of this + controller using the OF graph bindings specified if the "usb-role-switch" + property is used. + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: High Speed (HS) data bus. + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: Super Speed (SS) data bus. + + wakeup-source: + $ref: /schemas/types.yaml#/definitions/flag + description: + Enable USB remote wakeup. + unevaluatedProperties: false required: |