diff options
Diffstat (limited to 'dts/Bindings/usb')
| -rw-r--r-- | dts/Bindings/usb/amlogic,dwc3.txt | 88 | ||||
| -rw-r--r-- | dts/Bindings/usb/dwc2.txt | 7 | ||||
| -rw-r--r-- | dts/Bindings/usb/generic-ehci.yaml | 95 | ||||
| -rw-r--r-- | dts/Bindings/usb/generic-ohci.yaml | 89 | ||||
| -rw-r--r-- | dts/Bindings/usb/ingenic,jz4740-musb.txt | 8 | ||||
| -rw-r--r-- | dts/Bindings/usb/nvidia,tegra124-xusb.txt | 4 | ||||
| -rw-r--r-- | dts/Bindings/usb/renesas_usbhs.txt | 1 | ||||
| -rw-r--r-- | dts/Bindings/usb/usb-ehci.txt | 46 | ||||
| -rw-r--r-- | dts/Bindings/usb/usb-hcd.txt | 9 | ||||
| -rw-r--r-- | dts/Bindings/usb/usb-hcd.yaml | 25 | ||||
| -rw-r--r-- | dts/Bindings/usb/usb-ohci.txt | 35 | ||||
| -rw-r--r-- | dts/Bindings/usb/usb-xhci.txt | 1 | ||||
| -rw-r--r-- | dts/Bindings/usb/usb251xb.txt | 6 |
13 files changed, 322 insertions, 92 deletions
diff --git a/dts/Bindings/usb/amlogic,dwc3.txt b/dts/Bindings/usb/amlogic,dwc3.txt index 9a8b631904..b9f04e617e 100644 --- a/dts/Bindings/usb/amlogic,dwc3.txt +++ b/dts/Bindings/usb/amlogic,dwc3.txt @@ -40,3 +40,91 @@ Example device nodes: phy-names = "usb2-phy", "usb3-phy"; }; }; + +Amlogic Meson G12A DWC3 USB SoC Controller Glue + +The Amlogic G12A embeds a DWC3 USB IP Core configured for USB2 and USB3 +in host-only mode, and a DWC2 IP Core configured for USB2 peripheral mode +only. + +A glue connects the DWC3 core to USB2 PHYs and optionnaly to an USB3 PHY. + +One of the USB2 PHY can be re-routed in peripheral mode to a DWC2 USB IP. + +The DWC3 Glue controls the PHY routing and power, an interrupt line is +connected to the Glue to serve as OTG ID change detection. + +Required properties: +- compatible: Should be "amlogic,meson-g12a-usb-ctrl" +- clocks: a handle for the "USB" clock +- resets: a handle for the shared "USB" reset line +- reg: The base address and length of the registers +- interrupts: the interrupt specifier for the OTG detection +- phys: handle to used PHYs on the system + - a <0> phandle can be used if a PHY is not used +- phy-names: names of the used PHYs on the system : + - "usb2-phy0" for USB2 PHY0 if USBHOST_A port is used + - "usb2-phy1" for USB2 PHY1 if USBOTG_B port is used + - "usb3-phy0" for USB3 PHY if USB3_0 is used +- dr_mode: should be "host", "peripheral", or "otg" depending on + the usage and configuration of the OTG Capable port. + - "host" and "peripheral" means a fixed Host or Device only connection + - "otg" means the port can be used as both Host or Device and + be switched automatically using the OTG ID pin. + +Optional properties: +- vbus-supply: should be a phandle to the regulator controlling the VBUS + power supply when used in OTG switchable mode + +Required child nodes: + +A child node must exist to represent the core DWC3 IP block. The name of +the node is not important. The content of the node is defined in dwc3.txt. + +A child node must exist to represent the core DWC2 IP block. The name of +the node is not important. The content of the node is defined in dwc2.txt. + +PHY documentation is provided in the following places: +- Documentation/devicetree/bindings/phy/meson-g12a-usb2-phy.txt +- Documentation/devicetree/bindings/phy/meson-g12a-usb3-pcie-phy.txt + +Example device nodes: + usb: usb@ffe09000 { + compatible = "amlogic,meson-g12a-usb-ctrl"; + reg = <0x0 0xffe09000 0x0 0xa0>; + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + clocks = <&clkc CLKID_USB>; + resets = <&reset RESET_USB>; + + dr_mode = "otg"; + + phys = <&usb2_phy0>, <&usb2_phy1>, + <&usb3_pcie_phy PHY_TYPE_USB3>; + phy-names = "usb2-phy0", "usb2-phy1", "usb3-phy0"; + + dwc2: usb@ff400000 { + compatible = "amlogic,meson-g12a-usb", "snps,dwc2"; + reg = <0x0 0xff400000 0x0 0x40000>; + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clkc CLKID_USB1_DDR_BRIDGE>; + clock-names = "ddr"; + phys = <&usb2_phy1>; + dr_mode = "peripheral"; + g-rx-fifo-size = <192>; + g-np-tx-fifo-size = <128>; + g-tx-fifo-size = <128 128 16 16 16>; + }; + + dwc3: usb@ff500000 { + compatible = "snps,dwc3"; + reg = <0x0 0xff500000 0x0 0x100000>; + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; + dr_mode = "host"; + snps,dis_u2_susphy_quirk; + snps,quirk-frame-length-adjustment; + }; + }; diff --git a/dts/Bindings/usb/dwc2.txt b/dts/Bindings/usb/dwc2.txt index 6dc3c4a344..49eac0dc86 100644 --- a/dts/Bindings/usb/dwc2.txt +++ b/dts/Bindings/usb/dwc2.txt @@ -14,6 +14,7 @@ Required properties: - "amlogic,meson8-usb": The DWC2 USB controller instance in Amlogic Meson8 SoCs; - "amlogic,meson8b-usb": The DWC2 USB controller instance in Amlogic Meson8b SoCs; - "amlogic,meson-gxbb-usb": The DWC2 USB controller instance in Amlogic S905 SoCs; + - "amlogic,meson-g12a-usb": The DWC2 USB controller instance in Amlogic G12A SoCs; - "amcc,dwc-otg": The DWC2 USB controller instance in AMCC Canyonlands 460EX SoCs; - snps,dwc2: A generic DWC2 USB controller with default parameters. - "st,stm32f4x9-fsotg": The DWC2 USB FS/HS controller instance in STM32F4x9 SoCs @@ -31,12 +32,18 @@ Refer to clk/clock-bindings.txt for generic clock consumer properties Optional properties: - phys: phy provider specifier - phy-names: shall be "usb2-phy" +- vbus-supply: reference to the VBUS regulator. Depending on the current mode + this is enabled (in "host" mode") or disabled (in "peripheral" mode). The + regulator is updated if the controller is configured in "otg" mode and the + status changes between "host" and "peripheral". Refer to phy/phy-bindings.txt for generic phy consumer properties - dr_mode: shall be one of "host", "peripheral" and "otg" Refer to usb/generic.txt - g-rx-fifo-size: size of rx fifo size in gadget mode. - g-np-tx-fifo-size: size of non-periodic tx fifo size in gadget mode. - g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0) in gadget mode. +- snps,reset-phy-on-wake: If present indicates that we need to reset the PHY when + we detect a wakeup. This is due to a hardware errata. Deprecated properties: - g-use-dma: gadget DMA mode is automatically detected diff --git a/dts/Bindings/usb/generic-ehci.yaml b/dts/Bindings/usb/generic-ehci.yaml new file mode 100644 index 0000000000..d3b4f64159 --- /dev/null +++ b/dts/Bindings/usb/generic-ehci.yaml @@ -0,0 +1,95 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/usb/generic-ehci.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: USB EHCI Controller Device Tree Bindings + +allOf: + - $ref: "usb-hcd.yaml" + +maintainers: + - Greg Kroah-Hartman <gregkh@linuxfoundation.org> + +properties: + compatible: + contains: + const: generic-ehci + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + resets: + minItems: 1 + maxItems: 4 + + clocks: + minItems: 1 + maxItems: 4 + description: | + In case the Renesas R-Car Gen3 SoCs: + - if a host only channel: first clock should be host. + - if a USB DRD channel: first clock should be host and second + one should be peripheral + + big-endian: + $ref: /schemas/types.yaml#/definitions/flag + description: + Set this flag for HCDs with big endian descriptors and big + endian registers. + + big-endian-desc: + $ref: /schemas/types.yaml#/definitions/flag + description: + Set this flag for HCDs with big endian descriptors. + + big-endian-regs: + $ref: /schemas/types.yaml#/definitions/flag + description: + Set this flag for HCDs with big endian registers. + + has-transaction-translator: + $ref: /schemas/types.yaml#/definitions/flag + description: + Set this flag if EHCI has a Transaction Translator built into + the root hub. + + needs-reset-on-resume: + $ref: /schemas/types.yaml#/definitions/flag + description: + Set this flag to force EHCI reset after resume. + + phys: true + +required: + - compatible + - reg + - interrupts + +additionalProperties: false + +examples: + - | + ehci@e0000300 { + compatible = "ibm,usb-ehci-440epx", "generic-ehci"; + interrupt-parent = <&UIC0>; + interrupts = <0x1a 4>; + reg = <0 0xe0000300 90 0 0xe0000390 70>; + big-endian; + }; + + - | + ehci0: usb@1c14000 { + compatible = "allwinner,sun4i-a10-ehci", "generic-ehci"; + reg = <0x01c14000 0x100>; + interrupts = <39>; + clocks = <&ahb_gates 1>; + phys = <&usbphy 1>; + phy-names = "usb"; + }; + +... diff --git a/dts/Bindings/usb/generic-ohci.yaml b/dts/Bindings/usb/generic-ohci.yaml new file mode 100644 index 0000000000..da5a14becb --- /dev/null +++ b/dts/Bindings/usb/generic-ohci.yaml @@ -0,0 +1,89 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/usb/generic-ohci.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: USB OHCI Controller Device Tree Bindings + +allOf: + - $ref: "usb-hcd.yaml" + +maintainers: + - Greg Kroah-Hartman <gregkh@linuxfoundation.org> + +properties: + compatible: + contains: + const: generic-ohci + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + resets: + minItems: 1 + maxItems: 2 + + clocks: + minItems: 1 + maxItems: 3 + description: | + In case the Renesas R-Car Gen3 SoCs: + - if a host only channel: first clock should be host. + - if a USB DRD channel: first clock should be host and second + one should be peripheral + + big-endian: + $ref: /schemas/types.yaml#/definitions/flag + description: + Set this flag for HCDs with big endian descriptors and big + endian registers. + + big-endian-desc: + $ref: /schemas/types.yaml#/definitions/flag + description: + Set this flag for HCDs with big endian descriptors. + + big-endian-regs: + $ref: /schemas/types.yaml#/definitions/flag + description: + Set this flag for HCDs with big endian registers. + + remote-wakeup-connected: + $ref: /schemas/types.yaml#/definitions/flag + description: + Remote wakeup is wired on the platform. + + no-big-frame-no: + $ref: /schemas/types.yaml#/definitions/flag + description: + Set if frame_no lives in bits [15:0] of HCCA + + num-ports: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Overrides the detected port count + + phys: true + +required: + - compatible + - reg + - interrupts + +additionalProperties: false + +examples: + - | + ohci0: usb@1c14400 { + compatible = "allwinner,sun4i-a10-ohci", "generic-ohci"; + reg = <0x01c14400 0x100>; + interrupts = <64>; + clocks = <&usb_clk 6>, <&ahb_gates 2>; + phys = <&usbphy 1>; + }; + +... diff --git a/dts/Bindings/usb/ingenic,jz4740-musb.txt b/dts/Bindings/usb/ingenic,jz4740-musb.txt index 620355cee6..16808721f3 100644 --- a/dts/Bindings/usb/ingenic,jz4740-musb.txt +++ b/dts/Bindings/usb/ingenic,jz4740-musb.txt @@ -8,9 +8,15 @@ Required properties: - interrupt-names: must be "mc" - clocks: phandle to the "udc" clock - clock-names: must be "udc" +- phys: phandle to the USB PHY Example: +usb_phy: usb-phy@0 { + compatible = "usb-nop-xceiv"; + #phy-cells = <0>; +}; + udc: usb@13040000 { compatible = "ingenic,jz4740-musb"; reg = <0x13040000 0x10000>; @@ -21,4 +27,6 @@ udc: usb@13040000 { clocks = <&cgu JZ4740_CLK_UDC>; clock-names = "udc"; + + phys = <&usb_phy>; }; diff --git a/dts/Bindings/usb/nvidia,tegra124-xusb.txt b/dts/Bindings/usb/nvidia,tegra124-xusb.txt index 4156c3e181..5bfcc0b4d6 100644 --- a/dts/Bindings/usb/nvidia,tegra124-xusb.txt +++ b/dts/Bindings/usb/nvidia,tegra124-xusb.txt @@ -10,6 +10,7 @@ Required properties: - Tegra124: "nvidia,tegra124-xusb" - Tegra132: "nvidia,tegra132-xusb", "nvidia,tegra124-xusb" - Tegra210: "nvidia,tegra210-xusb" + - Tegra186: "nvidia,tegra186-xusb" - reg: Must contain the base and length of the xHCI host registers, XUSB FPCI registers and XUSB IPFS registers. - reg-names: Must contain the following entries: @@ -59,6 +60,8 @@ For Tegra210: - avdd-pll-uerefe-supply: PLLE reference PLL power supply. Must supply 1.05 V. - dvdd-pex-pll-supply: PCIe/USB3 PLL power supply. Must supply 1.05 V. - hvdd-pex-pll-e-supply: High-voltage PLLE power supply. Must supply 1.8 V. + +For Tegra210 and Tegra186: - power-domains: A list of PM domain specifiers that reference each power-domain used by the xHCI controller. This list must comprise of a specifier for the XUSBA and XUSBC power-domains. See ../power/power_domain.txt and @@ -78,6 +81,7 @@ Optional properties: - Tegra132: usb2-0, usb2-1, usb2-2, hsic-0, hsic-1, usb3-0, usb3-1 - Tegra210: usb2-0, usb2-1, usb2-2, usb2-3, hsic-0, usb3-0, usb3-1, usb3-2, usb3-3 + - Tegra186: usb2-0, usb2-1, usb2-2, hsic-0, usb3-0, usb3-1, usb3-2 Example: -------- diff --git a/dts/Bindings/usb/renesas_usbhs.txt b/dts/Bindings/usb/renesas_usbhs.txt index d93b6a1504..b8acc2a994 100644 --- a/dts/Bindings/usb/renesas_usbhs.txt +++ b/dts/Bindings/usb/renesas_usbhs.txt @@ -6,6 +6,7 @@ Required properties: - "renesas,usbhs-r8a7743" for r8a7743 (RZ/G1M) compatible device - "renesas,usbhs-r8a7744" for r8a7744 (RZ/G1N) compatible device - "renesas,usbhs-r8a7745" for r8a7745 (RZ/G1E) compatible device + - "renesas,usbhs-r8a77470" for r8a77470 (RZ/G1C) compatible device - "renesas,usbhs-r8a774a1" for r8a774a1 (RZ/G2M) compatible device - "renesas,usbhs-r8a774c0" for r8a774c0 (RZ/G2E) compatible device - "renesas,usbhs-r8a7790" for r8a7790 (R-Car H2) compatible device diff --git a/dts/Bindings/usb/usb-ehci.txt b/dts/Bindings/usb/usb-ehci.txt deleted file mode 100644 index 406252d14c..0000000000 --- a/dts/Bindings/usb/usb-ehci.txt +++ /dev/null @@ -1,46 +0,0 @@ -USB EHCI controllers - -Required properties: - - compatible : should be "generic-ehci". - - reg : should contain at least address and length of the standard EHCI - register set for the device. Optional platform-dependent registers - (debug-port or other) can be also specified here, but only after - definition of standard EHCI registers. - - interrupts : one EHCI interrupt should be described here. - -Optional properties: - - big-endian-regs : boolean, set this for hcds with big-endian registers - - big-endian-desc : boolean, set this for hcds with big-endian descriptors - - big-endian : boolean, for hcds with big-endian-regs + big-endian-desc - - needs-reset-on-resume : boolean, set this to force EHCI reset after resume - - has-transaction-translator : boolean, set this if EHCI have a Transaction - Translator built into the root hub. - - clocks : a list of phandle + clock specifier pairs. In case of Renesas - R-Car Gen3 SoCs: - - if a host only channel: first clock should be host. - - if a USB DRD channel: first clock should be host and second one - should be peripheral. - - phys : see usb-hcd.txt in the current directory - - resets : phandle + reset specifier pair - -additionally the properties from usb-hcd.txt (in the current directory) are -supported. - -Example (Sequoia 440EPx): - ehci@e0000300 { - compatible = "ibm,usb-ehci-440epx", "usb-ehci"; - interrupt-parent = <&UIC0>; - interrupts = <1a 4>; - reg = <0 e0000300 90 0 e0000390 70>; - big-endian; - }; - -Example (Allwinner sun4i A10 SoC): - ehci0: usb@1c14000 { - compatible = "allwinner,sun4i-a10-ehci", "generic-ehci"; - reg = <0x01c14000 0x100>; - interrupts = <39>; - clocks = <&ahb_gates 1>; - phys = <&usbphy 1>; - phy-names = "usb"; - }; diff --git a/dts/Bindings/usb/usb-hcd.txt b/dts/Bindings/usb/usb-hcd.txt deleted file mode 100644 index 50529b838c..0000000000 --- a/dts/Bindings/usb/usb-hcd.txt +++ /dev/null @@ -1,9 +0,0 @@ -Generic USB HCD (Host Controller Device) Properties - -Optional properties: -- phys: a list of all USB PHYs on this HCD - -Example: - &usb1 { - phys = <&usb2_phy1>, <&usb3_phy1>; - }; diff --git a/dts/Bindings/usb/usb-hcd.yaml b/dts/Bindings/usb/usb-hcd.yaml new file mode 100644 index 0000000000..9c8c56d3a7 --- /dev/null +++ b/dts/Bindings/usb/usb-hcd.yaml @@ -0,0 +1,25 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/usb/usb-hcd.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Generic USB Host Controller Device Tree Bindings + +maintainers: + - Greg Kroah-Hartman <gregkh@linuxfoundation.org> + +properties: + $nodename: + pattern: "^usb(@.*)?" + + phys: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: + List of all the USB PHYs on this HCD + +examples: + - | + usb { + phys = <&usb2_phy1>, <&usb3_phy1>; + }; diff --git a/dts/Bindings/usb/usb-ohci.txt b/dts/Bindings/usb/usb-ohci.txt deleted file mode 100644 index aaaa5255c9..0000000000 --- a/dts/Bindings/usb/usb-ohci.txt +++ /dev/null @@ -1,35 +0,0 @@ -USB OHCI controllers - -Required properties: -- compatible : "generic-ohci" -- reg : ohci controller register range (address and length) -- interrupts : ohci controller interrupt - -Optional properties: -- big-endian-regs : boolean, set this for hcds with big-endian registers -- big-endian-desc : boolean, set this for hcds with big-endian descriptors -- big-endian : boolean, for hcds with big-endian-regs + big-endian-desc -- no-big-frame-no : boolean, set if frame_no lives in bits [15:0] of HCCA -- remote-wakeup-connected: remote wakeup is wired on the platform -- num-ports : u32, to override the detected port count -- clocks : a list of phandle + clock specifier pairs. In case of Renesas - R-Car Gen3 SoCs: - - if a host only channel: first clock should be host. - - if a USB DRD channel: first clock should be host and second one - should be peripheral. -- phys : see usb-hcd.txt in the current directory -- resets : a list of phandle + reset specifier pairs - -additionally the properties from usb-hcd.txt (in the current directory) are -supported. - -Example: - - ohci0: usb@1c14400 { - compatible = "allwinner,sun4i-a10-ohci", "generic-ohci"; - reg = <0x01c14400 0x100>; - interrupts = <64>; - clocks = <&usb_clk 6>, <&ahb_gates 2>; - phys = <&usbphy 1>; - phy-names = "usb"; - }; diff --git a/dts/Bindings/usb/usb-xhci.txt b/dts/Bindings/usb/usb-xhci.txt index fea8b15457..97400e8f86 100644 --- a/dts/Bindings/usb/usb-xhci.txt +++ b/dts/Bindings/usb/usb-xhci.txt @@ -10,6 +10,7 @@ Required properties: - "renesas,xhci-r8a7743" for r8a7743 SoC - "renesas,xhci-r8a7744" for r8a7744 SoC - "renesas,xhci-r8a774a1" for r8a774a1 SoC + - "renesas,xhci-r8a774c0" for r8a774c0 SoC - "renesas,xhci-r8a7790" for r8a7790 SoC - "renesas,xhci-r8a7791" for r8a7791 SoC - "renesas,xhci-r8a7793" for r8a7793 SoC diff --git a/dts/Bindings/usb/usb251xb.txt b/dts/Bindings/usb/usb251xb.txt index 17915f64b8..bc7945e9db 100644 --- a/dts/Bindings/usb/usb251xb.txt +++ b/dts/Bindings/usb/usb251xb.txt @@ -64,8 +64,10 @@ Optional properties : - power-on-time-ms : Specifies the time it takes from the time the host initiates the power-on sequence to a port until the port has adequate power. The value is given in ms in a 0 - 510 range (default is 100ms). - - swap-dx-lanes : Specifies the ports which will swap the differential-pair - (D+/D-), default is not-swapped. + - swap-dx-lanes : Specifies the downstream ports which will swap the + differential-pair (D+/D-), default is not-swapped. + - swap-us-lanes : Selects the upstream port differential-pair (D+/D-) + swapping (boolean, default is not-swapped) Examples: usb2512b@2c { |