diff options
Diffstat (limited to 'dts/Bindings')
221 files changed, 5573 insertions, 353 deletions
diff --git a/dts/Bindings/arc/pct.txt b/dts/Bindings/arc/pct.txt new file mode 100644 index 0000000000..7b9588444f --- /dev/null +++ b/dts/Bindings/arc/pct.txt @@ -0,0 +1,20 @@ +* ARC Performance Counters + +The ARC700 can be configured with a pipeline performance monitor for counting +CPU and cache events like cache misses and hits. Like conventional PCT there +are 100+ hardware conditions dynamically mapped to upto 32 counters + +Note that: + * The ARC 700 PCT does not support interrupts; although HW events may be + counted, the HW events themselves cannot serve as a trigger for a sample. + +Required properties: + +- compatible : should contain + "snps,arc700-pct" + +Example: + +pmu { + compatible = "snps,arc700-pct"; +}; diff --git a/dts/Bindings/arc/pmu.txt b/dts/Bindings/arc/pmu.txt deleted file mode 100644 index 49d517340d..0000000000 --- a/dts/Bindings/arc/pmu.txt +++ /dev/null @@ -1,24 +0,0 @@ -* ARC Performance Monitor Unit - -The ARC 700 can be configured with a pipeline performance monitor for counting -CPU and cache events like cache misses and hits. - -Note that: - * ARC 700 refers to a family of ARC processor cores; - - There is only one type of PMU available for the whole family; - - The PMU may support different sets of events; supported events are probed - at boot time, as required by the reference manual. - - * The ARC 700 PMU does not support interrupts; although HW events may be - counted, the HW events themselves cannot serve as a trigger for a sample. - -Required properties: - -- compatible : should contain - "snps,arc700-pmu" - -Example: - -pmu { - compatible = "snps,arc700-pmu"; -}; diff --git a/dts/Bindings/arm/al,alpine.txt b/dts/Bindings/arm/al,alpine.txt new file mode 100644 index 0000000000..f404a4f9b1 --- /dev/null +++ b/dts/Bindings/arm/al,alpine.txt @@ -0,0 +1,88 @@ +Annapurna Labs Alpine Platform Device Tree Bindings +--------------------------------------------------------------- + +Boards in the Alpine family shall have the following properties: + +* Required root node properties: +compatible: must contain "al,alpine" + +* Example: + +/ { + model = "Annapurna Labs Alpine Dev Board"; + compatible = "al,alpine"; + + ... +} + +* CPU node: + +The Alpine platform includes cortex-a15 cores. +enable-method: must be "al,alpine-smp" to allow smp [1] + +Example: + +cpus { + #address-cells = <1>; + #size-cells = <0>; + enable-method = "al,alpine-smp"; + + cpu@0 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <0>; + }; + + cpu@1 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <1>; + }; + + cpu@2 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <2>; + }; + + cpu@3 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <3>; + }; +}; + + +* Alpine CPU resume registers + +The CPU resume register are used to define required resume address after +reset. + +Properties: +- compatible : Should contain "al,alpine-cpu-resume". +- reg : Offset and length of the register set for the device + +Example: + +cpu_resume { + compatible = "al,alpine-cpu-resume"; + reg = <0xfbff5ed0 0x30>; +}; + +* Alpine System-Fabric Service Registers + +The System-Fabric Service Registers allow various operation on CPU and +system fabric, like powering CPUs off. + +Properties: +- compatible : Should contain "al,alpine-sysfabric-service" and "syscon". +- reg : Offset and length of the register set for the device + +Example: + +nb_service { + compatible = "al,alpine-sysfabric-service", "syscon"; + reg = <0xfb070000 0x10000>; +}; + +[1] arm/cpu-enable-method/al,alpine-smp diff --git a/dts/Bindings/arm/altera.txt b/dts/Bindings/arm/altera.txt new file mode 100644 index 0000000000..558735aacc --- /dev/null +++ b/dts/Bindings/arm/altera.txt @@ -0,0 +1,14 @@ +Altera's SoCFPGA platform device tree bindings +--------------------------------------------- + +Boards with Cyclone 5 SoC: +Required root node properties: +compatible = "altr,socfpga-cyclone5", "altr,socfpga"; + +Boards with Arria 5 SoC: +Required root node properties: +compatible = "altr,socfpga-arria5", "altr,socfpga"; + +Boards with Arria 10 SoC: +Required root node properties: +compatible = "altr,socfpga-arria10", "altr,socfpga"; diff --git a/dts/Bindings/arm/amlogic.txt b/dts/Bindings/arm/amlogic.txt index 8fe8150461..973884a1ba 100644 --- a/dts/Bindings/arm/amlogic.txt +++ b/dts/Bindings/arm/amlogic.txt @@ -8,3 +8,7 @@ Boards with the Amlogic Meson6 SoC shall have the following properties: Boards with the Amlogic Meson8 SoC shall have the following properties: Required root node property: compatible: "amlogic,meson8"; + +Board compatible values: + - "geniatech,atv1200" + - "minix,neo-x8" diff --git a/dts/Bindings/arm/arch_timer.txt b/dts/Bindings/arm/arch_timer.txt index 256b4d8bab..e774128935 100644 --- a/dts/Bindings/arm/arch_timer.txt +++ b/dts/Bindings/arm/arch_timer.txt @@ -17,7 +17,10 @@ to deliver its interrupts via SPIs. - interrupts : Interrupt list for secure, non-secure, virtual and hypervisor timers, in that order. -- clock-frequency : The frequency of the main counter, in Hz. Optional. +- clock-frequency : The frequency of the main counter, in Hz. Should be present + only where necessary to work around broken firmware which does not configure + CNTFRQ on all CPUs to a uniform correct value. Use of this property is + strongly discouraged; fix your firmware unless absolutely impossible. - always-on : a boolean property. If present, the timer is powered through an always-on power domain, therefore it never loses context. @@ -46,7 +49,8 @@ Example: - compatible : Should at least contain "arm,armv7-timer-mem". -- clock-frequency : The frequency of the main counter, in Hz. Optional. +- clock-frequency : The frequency of the main counter, in Hz. Should be present + only when firmware has not configured the MMIO CNTFRQ registers. - reg : The control frame base address. diff --git a/dts/Bindings/arm/armada-39x.txt b/dts/Bindings/arm/armada-39x.txt new file mode 100644 index 0000000000..53d4ff9ea8 --- /dev/null +++ b/dts/Bindings/arm/armada-39x.txt @@ -0,0 +1,20 @@ +Marvell Armada 39x Platforms Device Tree Bindings +------------------------------------------------- + +Boards with a SoC of the Marvell Armada 39x family shall have the +following property: + +Required root node property: + + - compatible: must contain "marvell,armada390" + +In addition, boards using the Marvell Armada 398 SoC shall have the +following property before the previous one: + +Required root node property: + +compatible: must contain "marvell,armada398" + +Example: + +compatible = "marvell,a398-db", "marvell,armada398", "marvell,armada390"; diff --git a/dts/Bindings/arm/atmel-at91.txt b/dts/Bindings/arm/atmel-at91.txt index ad319f84f5..2e99b5b573 100644 --- a/dts/Bindings/arm/atmel-at91.txt +++ b/dts/Bindings/arm/atmel-at91.txt @@ -46,10 +46,12 @@ PIT Timer required properties: shared across all System Controller members. System Timer (ST) required properties: -- compatible: Should be "atmel,at91rm9200-st" +- compatible: Should be "atmel,at91rm9200-st", "syscon", "simple-mfd" - reg: Should contain registers location and length - interrupts: Should contain interrupt for the ST which is the IRQ line shared across all System Controller members. +Its subnodes can be: +- watchdog: compatible should be "atmel,at91rm9200-wdt" TC/TCLIB Timer required properties: - compatible: Should be "atmel,<chip>-tcb". diff --git a/dts/Bindings/arm/bcm/brcm,bcm11351-cpu-method b/dts/Bindings/arm/bcm/brcm,bcm11351-cpu-method.txt index 8240c023e2..8240c023e2 100644 --- a/dts/Bindings/arm/bcm/brcm,bcm11351-cpu-method +++ b/dts/Bindings/arm/bcm/brcm,bcm11351-cpu-method.txt diff --git a/dts/Bindings/arm/bcm/bcm11351.txt b/dts/Bindings/arm/bcm/brcm,bcm11351.txt index 0ff6560e60..0ff6560e60 100644 --- a/dts/Bindings/arm/bcm/bcm11351.txt +++ b/dts/Bindings/arm/bcm/brcm,bcm11351.txt diff --git a/dts/Bindings/arm/bcm/bcm21664.txt b/dts/Bindings/arm/bcm/brcm,bcm21664.txt index e0774255e1..e0774255e1 100644 --- a/dts/Bindings/arm/bcm/bcm21664.txt +++ b/dts/Bindings/arm/bcm/brcm,bcm21664.txt diff --git a/dts/Bindings/arm/bcm2835.txt b/dts/Bindings/arm/bcm/brcm,bcm2835.txt index ac683480c4..ac683480c4 100644 --- a/dts/Bindings/arm/bcm2835.txt +++ b/dts/Bindings/arm/bcm/brcm,bcm2835.txt diff --git a/dts/Bindings/arm/bcm4708.txt b/dts/Bindings/arm/bcm/brcm,bcm4708.txt index 6b0f49f6f4..6b0f49f6f4 100644 --- a/dts/Bindings/arm/bcm4708.txt +++ b/dts/Bindings/arm/bcm/brcm,bcm4708.txt diff --git a/dts/Bindings/arm/bcm/bcm63138.txt b/dts/Bindings/arm/bcm/brcm,bcm63138.txt index bd49987a88..bd49987a88 100644 --- a/dts/Bindings/arm/bcm/bcm63138.txt +++ b/dts/Bindings/arm/bcm/brcm,bcm63138.txt diff --git a/dts/Bindings/arm/brcm-brcmstb.txt b/dts/Bindings/arm/bcm/brcm,brcmstb.txt index 430608ec09..430608ec09 100644 --- a/dts/Bindings/arm/brcm-brcmstb.txt +++ b/dts/Bindings/arm/bcm/brcm,brcmstb.txt diff --git a/dts/Bindings/arm/bcm/cygnus.txt b/dts/Bindings/arm/bcm/brcm,cygnus.txt index 4c77169bb5..4c77169bb5 100644 --- a/dts/Bindings/arm/bcm/cygnus.txt +++ b/dts/Bindings/arm/bcm/brcm,cygnus.txt diff --git a/dts/Bindings/arm/cci.txt b/dts/Bindings/arm/cci.txt index f28d82bbbc..3c5c631328 100644 --- a/dts/Bindings/arm/cci.txt +++ b/dts/Bindings/arm/cci.txt @@ -94,8 +94,11 @@ specific to ARM. - compatible Usage: required Value type: <string> - Definition: must be "arm,cci-400-pmu" - + Definition: Must contain one of: + "arm,cci-400-pmu,r0" + "arm,cci-400-pmu,r1" + "arm,cci-400-pmu" - DEPRECATED, permitted only where OS has + secure acces to CCI registers - reg: Usage: required Value type: Integer cells. A register entry, expressed diff --git a/dts/Bindings/arm/coresight.txt b/dts/Bindings/arm/coresight.txt index a3089359aa..88602b7541 100644 --- a/dts/Bindings/arm/coresight.txt +++ b/dts/Bindings/arm/coresight.txt @@ -61,7 +61,6 @@ Example: compatible = "arm,coresight-etb10", "arm,primecell"; reg = <0 0x20010000 0 0x1000>; - coresight-default-sink; clocks = <&oscclk6a>; clock-names = "apb_pclk"; port { diff --git a/dts/Bindings/arm/cpu-enable-method/al,alpine-smp b/dts/Bindings/arm/cpu-enable-method/al,alpine-smp new file mode 100644 index 0000000000..c2e0cc5e4c --- /dev/null +++ b/dts/Bindings/arm/cpu-enable-method/al,alpine-smp @@ -0,0 +1,52 @@ +======================================================== +Secondary CPU enable-method "al,alpine-smp" binding +======================================================== + +This document describes the "al,alpine-smp" method for +enabling secondary CPUs. To apply to all CPUs, a single +"al,alpine-smp" enable method should be defined in the +"cpus" node. + +Enable method name: "al,alpine-smp" +Compatible machines: "al,alpine" +Compatible CPUs: "arm,cortex-a15" +Related properties: (none) + +Note: +This enable method requires valid nodes compatible with +"al,alpine-cpu-resume" and "al,alpine-nb-service"[1]. + +Example: + +cpus { + #address-cells = <1>; + #size-cells = <0>; + enable-method = "al,alpine-smp"; + + cpu@0 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <0>; + }; + + cpu@1 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <1>; + }; + + cpu@2 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <2>; + }; + + cpu@3 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <3>; + }; +}; + +-- +[1] arm/al,alpine.txt diff --git a/dts/Bindings/arm/cpus.txt b/dts/Bindings/arm/cpus.txt index 8b9e0a95de..6aa331d11c 100644 --- a/dts/Bindings/arm/cpus.txt +++ b/dts/Bindings/arm/cpus.txt @@ -192,6 +192,7 @@ nodes to be present and contain the properties described below. "brcm,brahma-b15" "marvell,armada-375-smp" "marvell,armada-380-smp" + "marvell,armada-390-smp" "marvell,armada-xp-smp" "qcom,gcc-msm8660" "qcom,kpss-acc-v1" diff --git a/dts/Bindings/arm/exynos/power_domain.txt b/dts/Bindings/arm/exynos/power_domain.txt index 1e09703734..5da38c5ed4 100644 --- a/dts/Bindings/arm/exynos/power_domain.txt +++ b/dts/Bindings/arm/exynos/power_domain.txt @@ -22,6 +22,9 @@ Optional Properties: - pclkN, clkN: Pairs of parent of input clock and input clock to the devices in this power domain. Maximum of 4 pairs (N = 0 to 3) are supported currently. + - asbN: Clocks required by asynchronous bridges (ASB) present in + the power domain. These clock should be enabled during power + domain on/off operations. - power-domains: phandle pointing to the parent power domain, for more details see Documentation/devicetree/bindings/power/power_domain.txt diff --git a/dts/Bindings/arm/freescale/fsl,vf610-mscm-cpucfg.txt b/dts/Bindings/arm/freescale/fsl,vf610-mscm-cpucfg.txt new file mode 100644 index 0000000000..44aa3c451c --- /dev/null +++ b/dts/Bindings/arm/freescale/fsl,vf610-mscm-cpucfg.txt @@ -0,0 +1,14 @@ +Freescale Vybrid Miscellaneous System Control - CPU Configuration + +The MSCM IP contains multiple sub modules, this binding describes the first +block of registers which contains CPU configuration information. + +Required properties: +- compatible: "fsl,vf610-mscm-cpucfg", "syscon" +- reg: the register range of the MSCM CPU configuration registers + +Example: + mscm_cpucfg: cpucfg@40001000 { + compatible = "fsl,vf610-mscm-cpucfg", "syscon"; + reg = <0x40001000 0x800>; + } diff --git a/dts/Bindings/arm/freescale/fsl,vf610-mscm-ir.txt b/dts/Bindings/arm/freescale/fsl,vf610-mscm-ir.txt new file mode 100644 index 0000000000..669808b2af --- /dev/null +++ b/dts/Bindings/arm/freescale/fsl,vf610-mscm-ir.txt @@ -0,0 +1,33 @@ +Freescale Vybrid Miscellaneous System Control - Interrupt Router + +The MSCM IP contains multiple sub modules, this binding describes the second +block of registers which control the interrupt router. The interrupt router +allows to configure the recipient of each peripheral interrupt. Furthermore +it controls the directed processor interrupts. The module is available in all +Vybrid SoC's but is only really useful in dual core configurations (VF6xx +which comes with a Cortex-A5/Cortex-M4 combination). + +Required properties: +- compatible: "fsl,vf610-mscm-ir" +- reg: the register range of the MSCM Interrupt Router +- fsl,cpucfg: The handle to the MSCM CPU configuration node, required + to get the current CPU ID +- interrupt-controller: Identifies the node as an interrupt controller +- #interrupt-cells: Two cells, interrupt number and cells. + The hardware interrupt number according to interrupt + assignment of the interrupt router is required. + Flags get passed only when using GIC as parent. Flags + encoding as documented by the GIC bindings. +- interrupt-parent: Should be the phandle for the interrupt controller of + the CPU the device tree is intended to be used on. This + is either the node of the GIC or NVIC controller. + +Example: + mscm_ir: interrupt-controller@40001800 { + compatible = "fsl,vf610-mscm-ir"; + reg = <0x40001800 0x400>; + fsl,cpucfg = <&mscm_cpucfg>; + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&intc>; + } diff --git a/dts/Bindings/arm/geniatech.txt b/dts/Bindings/arm/geniatech.txt deleted file mode 100644 index 74ccba40b7..0000000000 --- a/dts/Bindings/arm/geniatech.txt +++ /dev/null @@ -1,5 +0,0 @@ -Geniatech platforms device tree bindings -------------------------------------------- - -Geniatech ATV1200 - - compatible = "geniatech,atv1200" diff --git a/dts/Bindings/arm/gic.txt b/dts/Bindings/arm/gic.txt index c97484b73e..2da059a479 100644 --- a/dts/Bindings/arm/gic.txt +++ b/dts/Bindings/arm/gic.txt @@ -18,6 +18,8 @@ Main node required properties: "arm,arm11mp-gic" "brcm,brahma-b15-gic" "arm,arm1176jzf-devchip-gic" + "qcom,msm-8660-qgic" + "qcom,msm-qgic2" - interrupt-controller : Identifies the node as an interrupt controller - #interrupt-cells : Specifies the number of cells needed to encode an interrupt source. The type shall be a <u32> and the value shall be 3. @@ -56,11 +58,6 @@ Optional regions, used when the GIC doesn't have banked registers. The offset is cpu-offset * cpu-nr. -- arm,routable-irqs : Total number of gic irq inputs which are not directly - connected from the peripherals, but are routed dynamically - by a crossbar/multiplexer preceding the GIC. The GIC irq - input line is assigned dynamically when the corresponding - peripheral's crossbar line is mapped. Example: intc: interrupt-controller@fff11000 { @@ -68,7 +65,6 @@ Example: #interrupt-cells = <3>; #address-cells = <1>; interrupt-controller; - arm,routable-irqs = <160>; reg = <0xfff11000 0x1000>, <0xfff10100 0x100>; }; diff --git a/dts/Bindings/arm/marvell,kirkwood.txt b/dts/Bindings/arm/marvell,kirkwood.txt index 925ecbf6e7..4f40ff3fee 100644 --- a/dts/Bindings/arm/marvell,kirkwood.txt +++ b/dts/Bindings/arm/marvell,kirkwood.txt @@ -42,6 +42,7 @@ board. Currently known boards are: "lacie,cloudbox" "lacie,inetspace_v2" "lacie,laplug" +"lacie,nas2big" "lacie,netspace_lite_v2" "lacie,netspace_max_v2" "lacie,netspace_mini_v2" diff --git a/dts/Bindings/arm/msm/qcom,idle-state.txt b/dts/Bindings/arm/msm/qcom,idle-state.txt new file mode 100644 index 0000000000..06df04cc82 --- /dev/null +++ b/dts/Bindings/arm/msm/qcom,idle-state.txt @@ -0,0 +1,84 @@ +QCOM Idle States for cpuidle driver + +ARM provides idle-state node to define the cpuidle states, as defined in [1]. +cpuidle-qcom is the cpuidle driver for Qualcomm SoCs and uses these idle +states. Idle states have different enter/exit latency and residency values. +The idle states supported by the QCOM SoC are defined as - + + * Standby + * Retention + * Standalone Power Collapse (Standalone PC or SPC) + * Power Collapse (PC) + +Standby: Standby does a little more in addition to architectural clock gating. +When the WFI instruction is executed the ARM core would gate its internal +clocks. In addition to gating the clocks, QCOM cpus use this instruction as a +trigger to execute the SPM state machine. The SPM state machine waits for the +interrupt to trigger the core back in to active. This triggers the cache +hierarchy to enter standby states, when all cpus are idle. An interrupt brings +the SPM state machine out of its wait, the next step is to ensure that the +cache hierarchy is also out of standby, and then the cpu is allowed to resume +execution. This state is defined as a generic ARM WFI state by the ARM cpuidle +driver and is not defined in the DT. The SPM state machine should be +configured to execute this state by default and after executing every other +state below. + +Retention: Retention is a low power state where the core is clock gated and +the memory and the registers associated with the core are retained. The +voltage may be reduced to the minimum value needed to keep the processor +registers active. The SPM should be configured to execute the retention +sequence and would wait for interrupt, before restoring the cpu to execution +state. Retention may have a slightly higher latency than Standby. + +Standalone PC: A cpu can power down and warmboot if there is a sufficient time +between the time it enters idle and the next known wake up. SPC mode is used +to indicate a core entering a power down state without consulting any other +cpu or the system resources. This helps save power only on that core. The SPM +sequence for this idle state is programmed to power down the supply to the +core, wait for the interrupt, restore power to the core, and ensure the +system state including cache hierarchy is ready before allowing core to +resume. Applying power and resetting the core causes the core to warmboot +back into Elevation Level (EL) which trampolines the control back to the +kernel. Entering a power down state for the cpu, needs to be done by trapping +into a EL. Failing to do so, would result in a crash enforced by the warm boot +code in the EL for the SoC. On SoCs with write-back L1 cache, the cache has to +be flushed in s/w, before powering down the core. + +Power Collapse: This state is similar to the SPC mode, but distinguishes +itself in that the cpu acknowledges and permits the SoC to enter deeper sleep +modes. In a hierarchical power domain SoC, this means L2 and other caches can +be flushed, system bus, clocks - lowered, and SoC main XO clock gated and +voltages reduced, provided all cpus enter this state. Since the span of low +power modes possible at this state is vast, the exit latency and the residency +of this low power mode would be considered high even though at a cpu level, +this essentially is cpu power down. The SPM in this state also may handshake +with the Resource power manager (RPM) processor in the SoC to indicate a +complete application processor subsystem shut down. + +The idle-state for QCOM SoCs are distinguished by the compatible property of +the idle-states device node. + +The devicetree representation of the idle state should be - + +Required properties: + +- compatible: Must be one of - + "qcom,idle-state-ret", + "qcom,idle-state-spc", + "qcom,idle-state-pc", + and "arm,idle-state". + +Other required and optional properties are specified in [1]. + +Example: + + idle-states { + CPU_SPC: spc { + compatible = "qcom,idle-state-spc", "arm,idle-state"; + entry-latency-us = <150>; + exit-latency-us = <200>; + min-residency-us = <2000>; + }; + }; + +[1]. Documentation/devicetree/bindings/arm/idle-states.txt diff --git a/dts/Bindings/arm/msm/qcom,saw2.txt b/dts/Bindings/arm/msm/qcom,saw2.txt index 1505fb8e13..ae4afc6dcf 100644 --- a/dts/Bindings/arm/msm/qcom,saw2.txt +++ b/dts/Bindings/arm/msm/qcom,saw2.txt @@ -2,22 +2,31 @@ SPM AVS Wrapper 2 (SAW2) The SAW2 is a wrapper around the Subsystem Power Manager (SPM) and the Adaptive Voltage Scaling (AVS) hardware. The SPM is a programmable -micro-controller that transitions a piece of hardware (like a processor or +power-controller that transitions a piece of hardware (like a processor or subsystem) into and out of low power modes via a direct connection to the PMIC. It can also be wired up to interact with other processors in the system, notifying them when a low power state is entered or exited. +Multiple revisions of the SAW hardware are supported using these Device Nodes. +SAW2 revisions differ in the register offset and configuration data. Also, the +same revision of the SAW in different SoCs may have different configuration +data due the the differences in hardware capabilities. Hence the SoC name, the +version of the SAW hardware in that SoC and the distinction between cpu (big +or Little) or cache, may be needed to uniquely identify the SAW register +configuration and initialization data. The compatible string is used to +indicate this parameter. + PROPERTIES - compatible: Usage: required Value type: <string> - Definition: shall contain "qcom,saw2". A more specific value should be - one of: - "qcom,saw2-v1" - "qcom,saw2-v1.1" - "qcom,saw2-v2" - "qcom,saw2-v2.1" + Definition: Must have + "qcom,saw2" + A more specific value could be one of: + "qcom,apq8064-saw2-v1.1-cpu" + "qcom,msm8974-saw2-v2.1-cpu" + "qcom,apq8084-saw2-v2.1-cpu" - reg: Usage: required @@ -26,10 +35,23 @@ PROPERTIES the register region. An optional second element specifies the base address and size of the alias register region. +- regulator: + Usage: optional + Value type: boolean + Definition: Indicates that this SPM device acts as a regulator device + device for the core (CPU or Cache) the SPM is attached + to. -Example: +Example 1: - regulator@2099000 { + power-controller@2099000 { compatible = "qcom,saw2"; reg = <0x02099000 0x1000>, <0x02009000 0x1000>; + regulator; + }; + +Example 2: + saw0: power-controller@f9089000 { + compatible = "qcom,apq8084-saw2-v2.1-cpu", "qcom,saw2"; + reg = <0xf9089000 0x1000>, <0xf9009000 0x1000>; }; diff --git a/dts/Bindings/arm/msm/timer.txt b/dts/Bindings/arm/msm/timer.txt index 74607b6c11..5e10c34554 100644 --- a/dts/Bindings/arm/msm/timer.txt +++ b/dts/Bindings/arm/msm/timer.txt @@ -9,11 +9,17 @@ Properties: "qcom,scss-timer" - scorpion subsystem - interrupts : Interrupts for the debug timer, the first general purpose - timer, and optionally a second general purpose timer in that - order. + timer, and optionally a second general purpose timer, and + optionally as well, 2 watchdog interrupts, in that order. - reg : Specifies the base address of the timer registers. +- clocks: Reference to the parent clocks, one per output clock. The parents + must appear in the same order as the clock names. + +- clock-names: The name of the clocks as free-form strings. They should be in + the same order as the clocks. + - clock-frequency : The frequency of the debug timer and the general purpose timer(s) in Hz in that order. @@ -29,9 +35,13 @@ Example: compatible = "qcom,scss-timer", "qcom,msm-timer"; interrupts = <1 1 0x301>, <1 2 0x301>, - <1 3 0x301>; + <1 3 0x301>, + <1 4 0x301>, + <1 5 0x301>; reg = <0x0200a000 0x100>; clock-frequency = <19200000>, <32768>; + clocks = <&sleep_clk>; + clock-names = "sleep"; cpu-offset = <0x40000>; }; diff --git a/dts/Bindings/arm/omap/crossbar.txt b/dts/Bindings/arm/omap/crossbar.txt index 4139db353d..a9b28d74d9 100644 --- a/dts/Bindings/arm/omap/crossbar.txt +++ b/dts/Bindings/arm/omap/crossbar.txt @@ -9,7 +9,9 @@ inputs. Required properties: - compatible : Should be "ti,irq-crossbar" - reg: Base address and the size of the crossbar registers. -- ti,max-irqs: Total number of irqs available at the interrupt controller. +- interrupt-controller: indicates that this block is an interrupt controller. +- interrupt-parent: the interrupt controller this block is connected to. +- ti,max-irqs: Total number of irqs available at the parent interrupt controller. - ti,max-crossbar-sources: Maximum number of crossbar sources that can be routed. - ti,reg-size: Size of a individual register in bytes. Every individual register is assumed to be of same size. Valid sizes are 1, 2, 4. @@ -27,13 +29,13 @@ Optional properties: when the interrupt controller irq is unused (when not provided, default is 0) Examples: - crossbar_mpu: @4a020000 { + crossbar_mpu: crossbar@4a002a48 { compatible = "ti,irq-crossbar"; reg = <0x4a002a48 0x130>; ti,max-irqs = <160>; ti,max-crossbar-sources = <400>; ti,reg-size = <2>; - ti,irqs-reserved = <0 1 2 3 5 6 131 132 139 140>; + ti,irqs-reserved = <0 1 2 3 5 6 131 132>; ti,irqs-skip = <10 133 139 140>; }; @@ -44,10 +46,6 @@ Documentation/devicetree/bindings/arm/gic.txt for further details. An interrupt consumer on an SoC using crossbar will use: interrupts = <GIC_SPI request_number interrupt_level> -When the request number is between 0 to that described by -"ti,max-crossbar-sources", it is assumed to be a crossbar mapping. If the -request_number is greater than "ti,max-crossbar-sources", then it is mapped as a -quirky hardware mapping direct to GIC. Example: device_x@0x4a023000 { @@ -55,9 +53,3 @@ Example: interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; ... }; - - device_y@0x4a033000 { - /* Direct mapped GIC SPI 1 used */ - interrupts = <GIC_SPI DIRECT_IRQ(1) IRQ_TYPE_LEVEL_HIGH>; - ... - }; diff --git a/dts/Bindings/arm/omap/ctrl.txt b/dts/Bindings/arm/omap/ctrl.txt new file mode 100644 index 0000000000..3a4e5901ce --- /dev/null +++ b/dts/Bindings/arm/omap/ctrl.txt @@ -0,0 +1,79 @@ +OMAP Control Module bindings + +Control Module contains miscellaneous features under it based on SoC type. +Pincontrol is one common feature, and it has a specialized support +described in [1]. Typically some clock nodes are also under control module. +Syscon is used to share register level access to drivers external to +control module driver itself. + +See [2] for documentation about clock/clockdomain nodes. + +[1] Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt +[2] Documentation/devicetree/bindings/clock/ti/* + +Required properties: +- compatible: Must be one of: + "ti,am3-scm" + "ti,am4-scm" + "ti,dm814-scrm" + "ti,dm816-scrm" + "ti,omap2-scm" + "ti,omap3-scm" + "ti,omap4-scm-core" + "ti,omap4-scm-padconf-core" + "ti,omap5-scm-core" + "ti,omap5-scm-padconf-core" + "ti,dra7-scm-core" +- reg: Contains Control Module register address range + (base address and length) + +Optional properties: +- clocks: clocks for this module +- clockdomains: clockdomains for this module + +Examples: + +scm: scm@2000 { + compatible = "ti,omap3-scm", "simple-bus"; + reg = <0x2000 0x2000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x2000 0x2000>; + + omap3_pmx_core: pinmux@30 { + compatible = "ti,omap3-padconf", + "pinctrl-single"; + reg = <0x30 0x230>; + #address-cells = <1>; + #size-cells = <0>; + #interrupt-cells = <1>; + interrupt-controller; + pinctrl-single,register-width = <16>; + pinctrl-single,function-mask = <0xff1f>; + }; + + scm_conf: scm_conf@270 { + compatible = "syscon"; + reg = <0x270 0x330>; + #address-cells = <1>; + #size-cells = <1>; + + scm_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + scm_clockdomains: clockdomains { + }; +} + +&scm_clocks { + mcbsp5_mux_fck: mcbsp5_mux_fck { + #clock-cells = <0>; + compatible = "ti,composite-mux-clock"; + clocks = <&core_96m_fck>, <&mcbsp_clks>; + ti,bit-shift = <4>; + reg = <0x02d8>; + }; +}; diff --git a/dts/Bindings/arm/omap/l4.txt b/dts/Bindings/arm/omap/l4.txt new file mode 100644 index 0000000000..b4f8a16e7e --- /dev/null +++ b/dts/Bindings/arm/omap/l4.txt @@ -0,0 +1,26 @@ +L4 interconnect bindings + +These bindings describe the OMAP SoCs L4 interconnect bus. + +Required properties: +- compatible : Should be "ti,omap2-l4" for OMAP2 family l4 core bus + Should be "ti,omap2-l4-wkup" for OMAP2 family l4 wkup bus + Should be "ti,omap3-l4-core" for OMAP3 family l4 core bus + Should be "ti,omap4-l4-cfg" for OMAP4 family l4 cfg bus + Should be "ti,omap4-l4-wkup" for OMAP4 family l4 wkup bus + Should be "ti,omap5-l4-cfg" for OMAP5 family l4 cfg bus + Should be "ti,omap5-l4-wkup" for OMAP5 family l4 wkup bus + Should be "ti,dra7-l4-cfg" for DRA7 family l4 cfg bus + Should be "ti,dra7-l4-wkup" for DRA7 family l4 wkup bus + Should be "ti,am3-l4-wkup" for AM33xx family l4 wkup bus + Should be "ti,am4-l4-wkup" for AM43xx family l4 wkup bus +- ranges : contains the IO map range for the bus + +Examples: + +l4: l4@48000000 { + compatible "ti,omap2-l4", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x48000000 0x100000>; +}; diff --git a/dts/Bindings/arm/omap/prcm.txt b/dts/Bindings/arm/omap/prcm.txt index 79074dac68..3eb6d7afff 100644 --- a/dts/Bindings/arm/omap/prcm.txt +++ b/dts/Bindings/arm/omap/prcm.txt @@ -10,14 +10,10 @@ documentation about the individual clock/clockdomain nodes. Required properties: - compatible: Must be one of: "ti,am3-prcm" - "ti,am3-scrm" "ti,am4-prcm" - "ti,am4-scrm" "ti,omap2-prcm" - "ti,omap2-scrm" "ti,omap3-prm" "ti,omap3-cm" - "ti,omap3-scrm" "ti,omap4-cm1" "ti,omap4-prm" "ti,omap4-cm2" @@ -29,6 +25,8 @@ Required properties: "ti,dra7-prm" "ti,dra7-cm-core-aon" "ti,dra7-cm-core" + "ti,dm814-prcm" + "ti,dm816-prcm" - reg: Contains PRCM module register address range (base address and length) - clocks: clocks for this module diff --git a/dts/Bindings/arm/pmu.txt b/dts/Bindings/arm/pmu.txt index 75ef91d08f..3b5f5d1088 100644 --- a/dts/Bindings/arm/pmu.txt +++ b/dts/Bindings/arm/pmu.txt @@ -18,12 +18,21 @@ Required properties: "arm,arm11mpcore-pmu" "arm,arm1176-pmu" "arm,arm1136-pmu" + "qcom,scorpion-pmu" + "qcom,scorpion-mp-pmu" "qcom,krait-pmu" - interrupts : 1 combined interrupt or 1 per core. If the interrupt is a per-cpu interrupt (PPI) then 1 interrupt should be specified. Optional properties: +- interrupt-affinity : Valid only when using SPIs, specifies a list of phandles + to CPU nodes corresponding directly to the affinity of + the SPIs listed in the interrupts property. + + This property should be present when there is more than + a single SPI. + - qcom,no-pc-write : Indicates that this PMU doesn't support the 0xc and 0xd events. diff --git a/dts/Bindings/arm/rockchip.txt b/dts/Bindings/arm/rockchip.txt index 6809e4e51e..60d4a1e0a9 100644 --- a/dts/Bindings/arm/rockchip.txt +++ b/dts/Bindings/arm/rockchip.txt @@ -22,3 +22,7 @@ Rockchip platforms device tree bindings - compatible = "firefly,firefly-rk3288", "rockchip,rk3288"; or - compatible = "firefly,firefly-rk3288-beta", "rockchip,rk3288"; + +- ChipSPARK PopMetal-RK3288 board: + Required root node properties: + - compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288"; diff --git a/dts/Bindings/arm/samsung/pmu.txt b/dts/Bindings/arm/samsung/pmu.txt index 67b211381f..2d6356d8da 100644 --- a/dts/Bindings/arm/samsung/pmu.txt +++ b/dts/Bindings/arm/samsung/pmu.txt @@ -29,10 +29,27 @@ Properties: - clocks : list of phandles and specifiers to all input clocks listed in clock-names property. +Optional properties: + +Some PMUs are capable of behaving as an interrupt controller (mostly +to wake up a suspended PMU). In which case, they can have the +following properties: + +- interrupt-controller: indicate that said PMU is an interrupt controller + +- #interrupt-cells: must be identical to the that of the parent interrupt + controller. + +- interrupt-parent: a phandle indicating which interrupt controller + this PMU signals interrupts to. + Example : pmu_system_controller: system-controller@10040000 { compatible = "samsung,exynos5250-pmu", "syscon"; reg = <0x10040000 0x5000>; + interrupt-controller; + #interrupt-cells = <3>; + interrupt-parent = <&gic>; #clock-cells = <1>; clock-names = "clkout0", "clkout1", "clkout2", "clkout3", "clkout4", "clkout8", "clkout9"; diff --git a/dts/Bindings/arm/shmobile.txt b/dts/Bindings/arm/shmobile.txt index 51147cb5c0..c4f19b2e7d 100644 --- a/dts/Bindings/arm/shmobile.txt +++ b/dts/Bindings/arm/shmobile.txt @@ -7,8 +7,6 @@ SoCs: compatible = "renesas,emev2" - RZ/A1H (R7S72100) compatible = "renesas,r7s72100" - - SH-Mobile AP4 (R8A73720/SH7372) - compatible = "renesas,sh7372" - SH-Mobile AG5 (R8A73A00/SH73A0) compatible = "renesas,sh73a0" - R-Mobile APE6 (R8A73A40) @@ -37,8 +35,6 @@ Boards: compatible = "renesas,alt", "renesas,r8a7794" - APE6-EVM compatible = "renesas,ape6evm", "renesas,r8a73a4" - - APE6-EVM - Reference Device Tree Implementation - compatible = "renesas,ape6evm-reference", "renesas,r8a73a4" - Atmark Techno Armadillo-800 EVA compatible = "renesas,armadillo800eva" - BOCK-W @@ -57,12 +53,8 @@ Boards: compatible = "renesas,kzm9d", "renesas,emev2" - Kyoto Microcomputer Co. KZM-A9-GT compatible = "renesas,kzm9g", "renesas,sh73a0" - - Kyoto Microcomputer Co. KZM-A9-GT - Reference Device Tree Implementation - compatible = "renesas,kzm9g-reference", "renesas,sh73a0" - Lager (RTP0RC7790SEB00010S) compatible = "renesas,lager", "renesas,r8a7790" - - Mackerel (R0P7372LC0016RL, AP4 EVM 2nd) - compatible = "renesas,mackerel" - Marzen compatible = "renesas,marzen", "renesas,r8a7779" diff --git a/dts/Bindings/arm/tegra/nvidia,tegra20-ahb.txt b/dts/Bindings/arm/tegra/nvidia,tegra20-ahb.txt index 067c979006..9a4295b545 100644 --- a/dts/Bindings/arm/tegra/nvidia,tegra20-ahb.txt +++ b/dts/Bindings/arm/tegra/nvidia,tegra20-ahb.txt @@ -5,9 +5,12 @@ Required properties: Tegra30, must contain "nvidia,tegra30-ahb". Otherwise, must contain '"nvidia,<chip>-ahb", "nvidia,tegra30-ahb"' where <chip> is tegra124, tegra132, or tegra210. -- reg : Should contain 1 register ranges(address and length) +- reg : Should contain 1 register ranges(address and length). For + Tegra20, Tegra30, and Tegra114 chips, the value must be <0x6000c004 + 0x10c>. For Tegra124, Tegra132 and Tegra210 chips, the value should + be be <0x6000c000 0x150>. -Example: +Example (for a Tegra20 chip): ahb: ahb@6000c004 { compatible = "nvidia,tegra20-ahb"; reg = <0x6000c004 0x10c>; /* AHB Arbitration + Gizmo Controller */ diff --git a/dts/Bindings/arm/tegra/nvidia,tegra30-actmon.txt b/dts/Bindings/arm/tegra/nvidia,tegra30-actmon.txt new file mode 100644 index 0000000000..ea670a5d7e --- /dev/null +++ b/dts/Bindings/arm/tegra/nvidia,tegra30-actmon.txt @@ -0,0 +1,32 @@ +NVIDIA Tegra Activity Monitor + +The activity monitor block collects statistics about the behaviour of other +components in the system. This information can be used to derive the rate at +which the external memory needs to be clocked in order to serve all requests +from the monitored clients. + +Required properties: +- compatible: should be "nvidia,tegra<chip>-actmon" +- reg: offset and length of the register set for the device +- interrupts: standard interrupt property +- clocks: Must contain a phandle and clock specifier pair for each entry in +clock-names. See ../../clock/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - actmon + - emc +- resets: Must contain an entry for each entry in reset-names. See +../../reset/reset.txt for details. +- reset-names: Must include the following entries: + - actmon + +Example: + actmon@6000c800 { + compatible = "nvidia,tegra124-actmon"; + reg = <0x0 0x6000c800 0x0 0x400>; + interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA124_CLK_ACTMON>, + <&tegra_car TEGRA124_CLK_EMC>; + clock-names = "actmon", "emc"; + resets = <&tegra_car 119>; + reset-names = "actmon"; + }; diff --git a/dts/Bindings/ata/ahci-st.txt b/dts/Bindings/ata/ahci-st.txt index 0574a77a0b..e1d01df8e3 100644 --- a/dts/Bindings/ata/ahci-st.txt +++ b/dts/Bindings/ata/ahci-st.txt @@ -3,29 +3,48 @@ STMicroelectronics STi SATA controller This binding describes a SATA device. Required properties: - - compatible : Must be "st,sti-ahci" + - compatible : Must be "st,ahci" - reg : Physical base addresses and length of register sets - interrupts : Interrupt associated with the SATA device - interrupt-names : Associated name must be; "hostc" - - resets : The power-down and soft-reset lines of SATA IP - - reset-names : Associated names must be; "pwr-dwn" and "sw-rst" - clocks : The phandle for the clock - clock-names : Associated name must be; "ahci_clk" - - phys : The phandle for the PHY device + - phys : The phandle for the PHY port - phy-names : Associated name must be; "ahci_phy" +Optional properties: + - resets : The power-down, soft-reset and power-reset lines of SATA IP + - reset-names : Associated names must be; "pwr-dwn", "sw-rst" and "pwr-rst" + Example: + /* Example for stih416 */ sata0: sata@fe380000 { - compatible = "st,sti-ahci"; - reg = <0xfe380000 0x1000>; - interrupts = <GIC_SPI 157 IRQ_TYPE_NONE>; - interrupt-names = "hostc"; - phys = <&miphy365x_phy MIPHY_PORT_0 MIPHY_TYPE_SATA>; - phy-names = "ahci_phy"; - resets = <&powerdown STIH416_SATA0_POWERDOWN>, + compatible = "st,ahci"; + reg = <0xfe380000 0x1000>; + interrupts = <GIC_SPI 157 IRQ_TYPE_NONE>; + interrupt-names = "hostc"; + phys = <&phy_port0 PHY_TYPE_SATA>; + phy-names = "ahci_phy"; + resets = <&powerdown STIH416_SATA0_POWERDOWN>, <&softreset STIH416_SATA0_SOFTRESET>; - reset-names = "pwr-dwn", "sw-rst"; - clocks = <&clk_s_a0_ls CLK_ICN_REG>; - clock-names = "ahci_clk"; + reset-names = "pwr-dwn", "sw-rst"; + clocks = <&clk_s_a0_ls CLK_ICN_REG>; + clock-names = "ahci_clk"; + }; + + /* Example for stih407 family silicon */ + sata0: sata@9b20000 { + compatible = "st,ahci"; + reg = <0x9b20000 0x1000>; + interrupts = <GIC_SPI 159 IRQ_TYPE_NONE>; + interrupt-names = "hostc"; + phys = <&phy_port0 PHY_TYPE_SATA>; + phy-names = "ahci_phy"; + resets = <&powerdown STIH407_SATA0_POWERDOWN>, + <&softreset STIH407_SATA0_SOFTRESET>, + <&softreset STIH407_SATA0_PWR_SOFTRESET>; + reset-names = "pwr-dwn", "sw-rst", "pwr-rst"; + clocks = <&clk_s_c0_flexgen CLK_ICN_REG>; + clock-names = "ahci_clk"; }; diff --git a/dts/Bindings/bus/bcma.txt b/dts/Bindings/bus/brcm,bus-axi.txt index edd44d8021..edd44d8021 100644 --- a/dts/Bindings/bus/bcma.txt +++ b/dts/Bindings/bus/brcm,bus-axi.txt diff --git a/dts/Bindings/bus/omap-ocp2scp.txt b/dts/Bindings/bus/omap-ocp2scp.txt index 63dd805152..18729f6fe1 100644 --- a/dts/Bindings/bus/omap-ocp2scp.txt +++ b/dts/Bindings/bus/omap-ocp2scp.txt @@ -1,7 +1,8 @@ * OMAP OCP2SCP - ocp interface to scp interface properties: -- compatible : Should be "ti,omap-ocp2scp" +- compatible : Should be "ti,am437x-ocp2scp" for AM437x processor + Should be "ti,omap-ocp2scp" for all others - reg : Address and length of the register set for the device - #address-cells, #size-cells : Must be present if the device has sub-nodes - ranges : the child address space are mapped 1:1 onto the parent address space diff --git a/dts/Bindings/bus/renesas,bsc.txt b/dts/Bindings/bus/renesas,bsc.txt new file mode 100644 index 0000000000..90e9472694 --- /dev/null +++ b/dts/Bindings/bus/renesas,bsc.txt @@ -0,0 +1,46 @@ +Renesas Bus State Controller (BSC) +================================== + +The Renesas Bus State Controller (BSC, sometimes called "LBSC within Bus +Bridge", or "External Bus Interface") can be found in several Renesas ARM SoCs. +It provides an external bus for connecting multiple external devices to the +SoC, driving several chip select lines, for e.g. NOR FLASH, Ethernet and USB. + +While the BSC is a fairly simple memory-mapped bus, it may be part of a PM +domain, and may have a gateable functional clock. +Before a device connected to the BSC can be accessed, the PM domain +containing the BSC must be powered on, and the functional clock +driving the BSC must be enabled. + +The bindings for the BSC extend the bindings for "simple-pm-bus". + + +Required properties + - compatible: Must contain an SoC-specific value, and "renesas,bsc" and + "simple-pm-bus" as fallbacks. + SoC-specific values can be: + "renesas,bsc-r8a73a4" for R-Mobile APE6 (r8a73a4) + "renesas,bsc-sh73a0" for SH-Mobile AG5 (sh73a0) + - #address-cells, #size-cells, ranges: Must describe the mapping between + parent address and child address spaces. + - reg: Must contain the base address and length to access the bus controller. + +Optional properties: + - interrupts: Must contain a reference to the BSC interrupt, if available. + - clocks: Must contain a reference to the functional clock, if available. + - power-domains: Must contain a reference to the PM domain, if available. + + +Example: + + bsc: bus@fec10000 { + compatible = "renesas,bsc-sh73a0", "renesas,bsc", + "simple-pm-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0x20000000>; + reg = <0xfec10000 0x400>; + interrupts = <0 39 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&zb_clk>; + power-domains = <&pd_a4s>; + }; diff --git a/dts/Bindings/bus/simple-pm-bus.txt b/dts/Bindings/bus/simple-pm-bus.txt new file mode 100644 index 0000000000..d032237512 --- /dev/null +++ b/dts/Bindings/bus/simple-pm-bus.txt @@ -0,0 +1,44 @@ +Simple Power-Managed Bus +======================== + +A Simple Power-Managed Bus is a transparent bus that doesn't need a real +driver, as it's typically initialized by the boot loader. + +However, its bus controller is part of a PM domain, or under the control of a +functional clock. Hence, the bus controller's PM domain and/or clock must be +enabled for child devices connected to the bus (either on-SoC or externally) +to function. + +While "simple-pm-bus" follows the "simple-bus" set of properties, as specified +in ePAPR, it is not an extension of "simple-bus". + + +Required properties: + - compatible: Must contain at least "simple-pm-bus". + Must not contain "simple-bus". + It's recommended to let this be preceded by one or more + vendor-specific compatible values. + - #address-cells, #size-cells, ranges: Must describe the mapping between + parent address and child address spaces. + +Optional platform-specific properties for clock or PM domain control (at least +one of them is required): + - clocks: Must contain a reference to the functional clock(s), + - power-domains: Must contain a reference to the PM domain. +Please refer to the binding documentation for the clock and/or PM domain +providers for more details. + + +Example: + + bsc: bus@fec10000 { + compatible = "renesas,bsc-sh73a0", "renesas,bsc", + "simple-pm-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0x20000000>; + reg = <0xfec10000 0x400>; + interrupts = <0 39 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&zb_clk>; + power-domains = <&pd_a4s>; + }; diff --git a/dts/Bindings/clock/bcm-kona-clock.txt b/dts/Bindings/clock/brcm,kona-ccu.txt index 5286e260fc..5286e260fc 100644 --- a/dts/Bindings/clock/bcm-kona-clock.txt +++ b/dts/Bindings/clock/brcm,kona-ccu.txt diff --git a/dts/Bindings/clock/exynos3250-clock.txt b/dts/Bindings/clock/exynos3250-clock.txt index f57d9dd9ea..f1738b88c2 100644 --- a/dts/Bindings/clock/exynos3250-clock.txt +++ b/dts/Bindings/clock/exynos3250-clock.txt @@ -9,6 +9,8 @@ Required Properties: - "samsung,exynos3250-cmu" - controller compatible with Exynos3250 SoC. - "samsung,exynos3250-cmu-dmc" - controller compatible with Exynos3250 SoC for Dynamic Memory Controller domain. + - "samsung,exynos3250-cmu-isp" - ISP block clock controller compatible + with Exynos3250 SOC - reg: physical base address of the controller and length of memory mapped region. @@ -36,6 +38,12 @@ Example 1: Examples of clock controller nodes are listed below. #clock-cells = <1>; }; + cmu_isp: clock-controller@10048000 { + compatible = "samsung,exynos3250-cmu-isp"; + reg = <0x10048000 0x1000>; + #clock-cells = <1>; + }; + Example 2: UART controller node that consumes the clock generated by the clock controller. Refer to the standard clock bindings for information about 'clocks' and 'clock-names' property. diff --git a/dts/Bindings/clock/exynos5433-clock.txt b/dts/Bindings/clock/exynos5433-clock.txt new file mode 100644 index 0000000000..63379b04e0 --- /dev/null +++ b/dts/Bindings/clock/exynos5433-clock.txt @@ -0,0 +1,462 @@ +* Samsung Exynos5433 CMU (Clock Management Units) + +The Exynos5433 clock controller generates and supplies clock to various +controllers within the Exynos5433 SoC. + +Required Properties: + +- compatible: should be one of the following. + - "samsung,exynos5433-cmu-top" - clock controller compatible for CMU_TOP + which generates clocks for IMEM/FSYS/G3D/GSCL/HEVC/MSCL/G2D/MFC/PERIC/PERIS + domains and bus clocks. + - "samsung,exynos5433-cmu-cpif" - clock controller compatible for CMU_CPIF + which generates clocks for LLI (Low Latency Interface) IP. + - "samsung,exynos5433-cmu-mif" - clock controller compatible for CMU_MIF + which generates clocks for DRAM Memory Controller domain. + - "samsung,exynos5433-cmu-peric" - clock controller compatible for CMU_PERIC + which generates clocks for UART/I2C/SPI/I2S/PCM/SPDIF/PWM/SLIMBUS IPs. + - "samsung,exynos5433-cmu-peris" - clock controller compatible for CMU_PERIS + which generates clocks for PMU/TMU/MCT/WDT/RTC/SECKEY/TZPC IPs. + - "samsung,exynos5433-cmu-fsys" - clock controller compatible for CMU_FSYS + which generates clocks for USB/UFS/SDMMC/TSI/PDMA IPs. + - "samsung,exynos5433-cmu-g2d" - clock controller compatible for CMU_G2D + which generates clocks for G2D/MDMA IPs. + - "samsung,exynos5433-cmu-disp" - clock controller compatible for CMU_DISP + which generates clocks for Display (DECON/HDMI/DSIM/MIXER) IPs. + - "samsung,exynos5433-cmu-aud" - clock controller compatible for CMU_AUD + which generates clocks for Cortex-A5/BUS/AUDIO clocks. + - "samsung,exynos5433-cmu-bus0", "samsung,exynos5433-cmu-bus1" + and "samsung,exynos5433-cmu-bus2" - clock controller compatible for CMU_BUS + which generates global data buses clock and global peripheral buses clock. + - "samsung,exynos5433-cmu-g3d" - clock controller compatible for CMU_G3D + which generates clocks for 3D Graphics Engine IP. + - "samsung,exynos5433-cmu-gscl" - clock controller compatible for CMU_GSCL + which generates clocks for GSCALER IPs. + - "samsung,exynos5433-cmu-apollo"- clock controller compatible for CMU_APOLLO + which generates clocks for Cortex-A53 Quad-core processor. + - "samsung,exynos5433-cmu-atlas" - clock controller compatible for CMU_ATLAS + which generates clocks for Cortex-A57 Quad-core processor, CoreSight and + L2 cache controller. + - "samsung,exynos5433-cmu-mscl" - clock controller compatible for CMU_MSCL + which generates clocks for M2M (Memory to Memory) scaler and JPEG IPs. + - "samsung,exynos5433-cmu-mfc" - clock controller compatible for CMU_MFC + which generates clocks for MFC(Multi-Format Codec) IP. + - "samsung,exynos5433-cmu-hevc" - clock controller compatible for CMU_HEVC + which generates clocks for HEVC(High Efficiency Video Codec) decoder IP. + - "samsung,exynos5433-cmu-isp" - clock controller compatible for CMU_ISP + which generates clocks for FIMC-ISP/DRC/SCLC/DIS/3DNR IPs. + - "samsung,exynos5433-cmu-cam0" - clock controller compatible for CMU_CAM0 + which generates clocks for MIPI_CSIS{0|1}/FIMC_LITE_{A|B|D}/FIMC_3AA{0|1} + IPs. + - "samsung,exynos5433-cmu-cam1" - clock controller compatible for CMU_CAM1 + which generates clocks for Cortex-A5/MIPI_CSIS2/FIMC-LITE_C/FIMC-FD IPs. + +- reg: physical base address of the controller and length of memory mapped + region. + +- #clock-cells: should be 1. + +- clocks: list of the clock controller input clock identifiers, + from common clock bindings. Please refer the next section + to find the input clocks for a given controller. + +- clock-names: list of the clock controller input clock names, + as described in clock-bindings.txt. + + Input clocks for top clock controller: + - oscclk + - sclk_mphy_pll + - sclk_mfc_pll + - sclk_bus_pll + + Input clocks for cpif clock controller: + - oscclk + + Input clocks for mif clock controller: + - oscclk + - sclk_mphy_pll + + Input clocks for fsys clock controller: + - oscclk + - sclk_ufs_mphy + - div_aclk_fsys_200 + - sclk_pcie_100_fsys + - sclk_ufsunipro_fsys + - sclk_mmc2_fsys + - sclk_mmc1_fsys + - sclk_mmc0_fsys + - sclk_usbhost30_fsys + - sclk_usbdrd30_fsys + + Input clocks for g2d clock controller: + - oscclk + - aclk_g2d_266 + - aclk_g2d_400 + + Input clocks for disp clock controller: + - oscclk + - sclk_dsim1_disp + - sclk_dsim0_disp + - sclk_dsd_disp + - sclk_decon_tv_eclk_disp + - sclk_decon_vclk_disp + - sclk_decon_eclk_disp + - sclk_decon_tv_vclk_disp + - aclk_disp_333 + + Input clocks for bus0 clock controller: + - aclk_bus0_400 + + Input clocks for bus1 clock controller: + - aclk_bus1_400 + + Input clocks for bus2 clock controller: + - oscclk + - aclk_bus2_400 + + Input clocks for g3d clock controller: + - oscclk + - aclk_g3d_400 + + Input clocks for gscl clock controller: + - oscclk + - aclk_gscl_111 + - aclk_gscl_333 + + Input clocks for apollo clock controller: + - oscclk + - sclk_bus_pll_apollo + + Input clocks for atlas clock controller: + - oscclk + - sclk_bus_pll_atlas + + Input clocks for mscl clock controller: + - oscclk + - sclk_jpeg_mscl + - aclk_mscl_400 + + Input clocks for mfc clock controller: + - oscclk + - aclk_mfc_400 + + Input clocks for hevc clock controller: + - oscclk + - aclk_hevc_400 + + Input clocks for isp clock controller: + - oscclk + - aclk_isp_dis_400 + - aclk_isp_400 + + Input clocks for cam0 clock controller: + - oscclk + - aclk_cam0_333 + - aclk_cam0_400 + - aclk_cam0_552 + + Input clocks for cam1 clock controller: + - oscclk + - sclk_isp_uart_cam1 + - sclk_isp_spi1_cam1 + - sclk_isp_spi0_cam1 + - aclk_cam1_333 + - aclk_cam1_400 + - aclk_cam1_552 + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/exynos5433.h header and can be used in device +tree sources. + +Example 1: Examples of 'oscclk' source clock node are listed below. + + xxti: xxti { + compatible = "fixed-clock"; + clock-output-names = "oscclk"; + #clock-cells = <0>; + }; + +Example 2: Examples of clock controller nodes are listed below. + + cmu_top: clock-controller@10030000 { + compatible = "samsung,exynos5433-cmu-top"; + reg = <0x10030000 0x0c04>; + #clock-cells = <1>; + + clock-names = "oscclk", + "sclk_mphy_pll", + "sclk_mfc_pll", + "sclk_bus_pll"; + clocks = <&xxti>, + <&cmu_cpif CLK_SCLK_MPHY_PLL>, + <&cmu_mif CLK_SCLK_MFC_PLL>, + <&cmu_mif CLK_SCLK_BUS_PLL>; + }; + + cmu_cpif: clock-controller@10fc0000 { + compatible = "samsung,exynos5433-cmu-cpif"; + reg = <0x10fc0000 0x0c04>; + #clock-cells = <1>; + + clock-names = "oscclk"; + clocks = <&xxti>; + }; + + cmu_mif: clock-controller@105b0000 { + compatible = "samsung,exynos5433-cmu-mif"; + reg = <0x105b0000 0x100c>; + #clock-cells = <1>; + + clock-names = "oscclk", + "sclk_mphy_pll"; + clocks = <&xxti>, + <&cmu_cpif CLK_SCLK_MPHY_PLL>; + }; + + cmu_peric: clock-controller@14c80000 { + compatible = "samsung,exynos5433-cmu-peric"; + reg = <0x14c80000 0x0b08>; + #clock-cells = <1>; + }; + + cmu_peris: clock-controller@10040000 { + compatible = "samsung,exynos5433-cmu-peris"; + reg = <0x10040000 0x0b20>; + #clock-cells = <1>; + }; + + cmu_fsys: clock-controller@156e0000 { + compatible = "samsung,exynos5433-cmu-fsys"; + reg = <0x156e0000 0x0b04>; + #clock-cells = <1>; + + clock-names = "oscclk", + "sclk_ufs_mphy", + "div_aclk_fsys_200", + "sclk_pcie_100_fsys", + "sclk_ufsunipro_fsys", + "sclk_mmc2_fsys", + "sclk_mmc1_fsys", + "sclk_mmc0_fsys", + "sclk_usbhost30_fsys", + "sclk_usbdrd30_fsys"; + clocks = <&xxti>, + <&cmu_cpif CLK_SCLK_UFS_MPHY>, + <&cmu_top CLK_DIV_ACLK_FSYS_200>, + <&cmu_top CLK_SCLK_PCIE_100_FSYS>, + <&cmu_top CLK_SCLK_UFSUNIPRO_FSYS>, + <&cmu_top CLK_SCLK_MMC2_FSYS>, + <&cmu_top CLK_SCLK_MMC1_FSYS>, + <&cmu_top CLK_SCLK_MMC0_FSYS>, + <&cmu_top CLK_SCLK_USBHOST30_FSYS>, + <&cmu_top CLK_SCLK_USBDRD30_FSYS>; + }; + + cmu_g2d: clock-controller@12460000 { + compatible = "samsung,exynos5433-cmu-g2d"; + reg = <0x12460000 0x0b08>; + #clock-cells = <1>; + + clock-names = "oscclk", + "aclk_g2d_266", + "aclk_g2d_400"; + clocks = <&xxti>, + <&cmu_top CLK_ACLK_G2D_266>, + <&cmu_top CLK_ACLK_G2D_400>; + }; + + cmu_disp: clock-controller@13b90000 { + compatible = "samsung,exynos5433-cmu-disp"; + reg = <0x13b90000 0x0c04>; + #clock-cells = <1>; + + clock-names = "oscclk", + "sclk_dsim1_disp", + "sclk_dsim0_disp", + "sclk_dsd_disp", + "sclk_decon_tv_eclk_disp", + "sclk_decon_vclk_disp", + "sclk_decon_eclk_disp", + "sclk_decon_tv_vclk_disp", + "aclk_disp_333"; + clocks = <&xxti>, + <&cmu_mif CLK_SCLK_DSIM1_DISP>, + <&cmu_mif CLK_SCLK_DSIM0_DISP>, + <&cmu_mif CLK_SCLK_DSD_DISP>, + <&cmu_mif CLK_SCLK_DECON_TV_ECLK_DISP>, + <&cmu_mif CLK_SCLK_DECON_VCLK_DISP>, + <&cmu_mif CLK_SCLK_DECON_ECLK_DISP>, + <&cmu_mif CLK_SCLK_DECON_TV_VCLK_DISP>, + <&cmu_mif CLK_ACLK_DISP_333>; + }; + + cmu_aud: clock-controller@114c0000 { + compatible = "samsung,exynos5433-cmu-aud"; + reg = <0x114c0000 0x0b04>; + #clock-cells = <1>; + }; + + cmu_bus0: clock-controller@13600000 { + compatible = "samsung,exynos5433-cmu-bus0"; + reg = <0x13600000 0x0b04>; + #clock-cells = <1>; + + clock-names = "aclk_bus0_400"; + clocks = <&cmu_top CLK_ACLK_BUS0_400>; + }; + + cmu_bus1: clock-controller@14800000 { + compatible = "samsung,exynos5433-cmu-bus1"; + reg = <0x14800000 0x0b04>; + #clock-cells = <1>; + + clock-names = "aclk_bus1_400"; + clocks = <&cmu_top CLK_ACLK_BUS1_400>; + }; + + cmu_bus2: clock-controller@13400000 { + compatible = "samsung,exynos5433-cmu-bus2"; + reg = <0x13400000 0x0b04>; + #clock-cells = <1>; + + clock-names = "oscclk", "aclk_bus2_400"; + clocks = <&xxti>, <&cmu_mif CLK_ACLK_BUS2_400>; + }; + + cmu_g3d: clock-controller@14aa0000 { + compatible = "samsung,exynos5433-cmu-g3d"; + reg = <0x14aa0000 0x1000>; + #clock-cells = <1>; + + clock-names = "oscclk", "aclk_g3d_400"; + clocks = <&xxti>, <&cmu_top CLK_ACLK_G3D_400>; + }; + + cmu_gscl: clock-controller@13cf0000 { + compatible = "samsung,exynos5433-cmu-gscl"; + reg = <0x13cf0000 0x0b10>; + #clock-cells = <1>; + + clock-names = "oscclk", + "aclk_gscl_111", + "aclk_gscl_333"; + clocks = <&xxti>, + <&cmu_top CLK_ACLK_GSCL_111>, + <&cmu_top CLK_ACLK_GSCL_333>; + }; + + cmu_apollo: clock-controller@11900000 { + compatible = "samsung,exynos5433-cmu-apollo"; + reg = <0x11900000 0x1088>; + #clock-cells = <1>; + + clock-names = "oscclk", "sclk_bus_pll_apollo"; + clocks = <&xxti>, <&cmu_mif CLK_SCLK_BUS_PLL_APOLLO>; + }; + + cmu_atlas: clock-controller@11800000 { + compatible = "samsung,exynos5433-cmu-atlas"; + reg = <0x11800000 0x1088>; + #clock-cells = <1>; + + clock-names = "oscclk", "sclk_bus_pll_atlas"; + clocks = <&xxti>, <&cmu_mif CLK_SCLK_BUS_PLL_ATLAS>; + }; + + cmu_mscl: clock-controller@105d0000 { + compatible = "samsung,exynos5433-cmu-mscl"; + reg = <0x105d0000 0x0b10>; + #clock-cells = <1>; + + clock-names = "oscclk", + "sclk_jpeg_mscl", + "aclk_mscl_400"; + clocks = <&xxti>, + <&cmu_top CLK_SCLK_JPEG_MSCL>, + <&cmu_top CLK_ACLK_MSCL_400>; + }; + + cmu_mfc: clock-controller@15280000 { + compatible = "samsung,exynos5433-cmu-mfc"; + reg = <0x15280000 0x0b08>; + #clock-cells = <1>; + + clock-names = "oscclk", "aclk_mfc_400"; + clocks = <&xxti>, <&cmu_top CLK_ACLK_MFC_400>; + }; + + cmu_hevc: clock-controller@14f80000 { + compatible = "samsung,exynos5433-cmu-hevc"; + reg = <0x14f80000 0x0b08>; + #clock-cells = <1>; + + clock-names = "oscclk", "aclk_hevc_400"; + clocks = <&xxti>, <&cmu_top CLK_ACLK_HEVC_400>; + }; + + cmu_isp: clock-controller@146d0000 { + compatible = "samsung,exynos5433-cmu-isp"; + reg = <0x146d0000 0x0b0c>; + #clock-cells = <1>; + + clock-names = "oscclk", + "aclk_isp_dis_400", + "aclk_isp_400"; + clocks = <&xxti>, + <&cmu_top CLK_ACLK_ISP_DIS_400>, + <&cmu_top CLK_ACLK_ISP_400>; + }; + + cmu_cam0: clock-controller@120d0000 { + compatible = "samsung,exynos5433-cmu-cam0"; + reg = <0x120d0000 0x0b0c>; + #clock-cells = <1>; + + clock-names = "oscclk", + "aclk_cam0_333", + "aclk_cam0_400", + "aclk_cam0_552"; + clocks = <&xxti>, + <&cmu_top CLK_ACLK_CAM0_333>, + <&cmu_top CLK_ACLK_CAM0_400>, + <&cmu_top CLK_ACLK_CAM0_552>; + }; + + cmu_cam1: clock-controller@145d0000 { + compatible = "samsung,exynos5433-cmu-cam1"; + reg = <0x145d0000 0x0b08>; + #clock-cells = <1>; + + clock-names = "oscclk", + "sclk_isp_uart_cam1", + "sclk_isp_spi1_cam1", + "sclk_isp_spi0_cam1", + "aclk_cam1_333", + "aclk_cam1_400", + "aclk_cam1_552"; + clocks = <&xxti>, + <&cmu_top CLK_SCLK_ISP_UART_CAM1>, + <&cmu_top CLK_SCLK_ISP_SPI1_CAM1>, + <&cmu_top CLK_SCLK_ISP_SPI0_CAM1>, + <&cmu_top CLK_ACLK_CAM1_333>, + <&cmu_top CLK_ACLK_CAM1_400>, + <&cmu_top CLK_ACLK_CAM1_552>; + }; + +Example 3: UART controller node that consumes the clock generated by the clock + controller. + + serial_0: serial@14C10000 { + compatible = "samsung,exynos5433-uart"; + reg = <0x14C10000 0x100>; + interrupts = <0 421 0>; + clocks = <&cmu_peric CLK_PCLK_UART0>, + <&cmu_peric CLK_SCLK_UART0>; + clock-names = "uart", "clk_uart_baud0"; + pinctrl-names = "default"; + pinctrl-0 = <&uart0_bus>; + status = "disabled"; + }; diff --git a/dts/Bindings/clock/fujitsu,mb86s70-crg11.txt b/dts/Bindings/clock/fujitsu,mb86s70-crg11.txt new file mode 100644 index 0000000000..3323962656 --- /dev/null +++ b/dts/Bindings/clock/fujitsu,mb86s70-crg11.txt @@ -0,0 +1,26 @@ +Fujitsu CRG11 clock driver bindings +----------------------------------- + +Required properties : +- compatible : Shall contain "fujitsu,mb86s70-crg11" +- #clock-cells : Shall be 3 {cntrlr domain port} + +The consumer specifies the desired clock pointing to its phandle. + +Example: + + clock: crg11 { + compatible = "fujitsu,mb86s70-crg11"; + #clock-cells = <3>; + }; + + mhu: mhu0@2b1f0000 { + #mbox-cells = <1>; + compatible = "arm,mhu"; + reg = <0 0x2B1F0000 0x1000>; + interrupts = <0 36 4>, /* LP Non-Sec */ + <0 35 4>, /* HP Non-Sec */ + <0 37 4>; /* Secure */ + clocks = <&clock 0 2 1>; /* Cntrlr:0 Domain:2 Port:1 */ + clock-names = "clk"; + }; diff --git a/dts/Bindings/clock/mvebu-core-clock.txt b/dts/Bindings/clock/mvebu-core-clock.txt index dc5ea5b22d..670c2af3e9 100644 --- a/dts/Bindings/clock/mvebu-core-clock.txt +++ b/dts/Bindings/clock/mvebu-core-clock.txt @@ -23,6 +23,14 @@ The following is a list of provided IDs and clock names on Armada 380/385: 2 = l2clk (L2 Cache clock) 3 = ddrclk (DDR clock) +The following is a list of provided IDs and clock names on Armada 39x: + 0 = tclk (Internal Bus clock) + 1 = cpuclk (CPU clock) + 2 = nbclk (Coherent Fabric clock) + 3 = hclk (SDRAM Controller Internal Clock) + 4 = dclk (SDRAM Interface Clock) + 5 = refclk (Reference Clock) + The following is a list of provided IDs and clock names on Kirkwood and Dove: 0 = tclk (Internal Bus clock) 1 = cpuclk (CPU0 clock) @@ -39,6 +47,7 @@ Required properties: "marvell,armada-370-core-clock" - For Armada 370 SoC core clocks "marvell,armada-375-core-clock" - For Armada 375 SoC core clocks "marvell,armada-380-core-clock" - For Armada 380/385 SoC core clocks + "marvell,armada-390-core-clock" - For Armada 39x SoC core clocks "marvell,armada-xp-core-clock" - For Armada XP SoC core clocks "marvell,dove-core-clock" - for Dove SoC core clocks "marvell,kirkwood-core-clock" - for Kirkwood SoC (except mv88f6180) diff --git a/dts/Bindings/clock/mvebu-gated-clock.txt b/dts/Bindings/clock/mvebu-gated-clock.txt index 76477be742..31c7c0c1ce 100644 --- a/dts/Bindings/clock/mvebu-gated-clock.txt +++ b/dts/Bindings/clock/mvebu-gated-clock.txt @@ -1,6 +1,6 @@ * Gated Clock bindings for Marvell EBU SoCs -Marvell Armada 370/375/380/385/XP, Dove and Kirkwood allow some +Marvell Armada 370/375/380/385/39x/XP, Dove and Kirkwood allow some peripheral clocks to be gated to save some power. The clock consumer should specify the desired clock by having the clock ID in its "clocks" phandle cell. The clock ID is directly mapped to the @@ -77,6 +77,18 @@ ID Clock Peripheral 28 xor1 XOR 1 30 sata1 SATA 1 +The following is a list of provided IDs for Armada 39x: +ID Clock Peripheral +----------------------------------- +5 pex1 PCIe 1 +6 pex2 PCIe 2 +7 pex3 PCIe 3 +8 pex0 PCIe 0 +9 usb3h0 USB3 Host 0 +17 sdio SDIO +22 xor0 XOR 0 +28 xor1 XOR 1 + The following is a list of provided IDs for Armada XP: ID Clock Peripheral ----------------------------------- @@ -152,6 +164,7 @@ Required properties: "marvell,armada-370-gating-clock" - for Armada 370 SoC clock gating "marvell,armada-375-gating-clock" - for Armada 375 SoC clock gating "marvell,armada-380-gating-clock" - for Armada 380/385 SoC clock gating + "marvell,armada-390-gating-clock" - for Armada 39x SoC clock gating "marvell,armada-xp-gating-clock" - for Armada XP SoC clock gating "marvell,dove-gating-clock" - for Dove SoC clock gating "marvell,kirkwood-gating-clock" - for Kirkwood SoC clock gating diff --git a/dts/Bindings/clock/pistachio-clock.txt b/dts/Bindings/clock/pistachio-clock.txt new file mode 100644 index 0000000000..868db499ee --- /dev/null +++ b/dts/Bindings/clock/pistachio-clock.txt @@ -0,0 +1,123 @@ +Imagination Technologies Pistachio SoC clock controllers +======================================================== + +Pistachio has four clock controllers (core clock, peripheral clock, peripheral +general control, and top general control) which are instantiated individually +from the device-tree. + +External clocks: +---------------- + +There are three external inputs to the clock controllers which should be +defined with the following clock-output-names: +- "xtal": External 52Mhz oscillator (required) +- "audio_clk_in": Alternate audio reference clock (optional) +- "enet_clk_in": Alternate ethernet PHY clock (optional) + +Core clock controller: +---------------------- + +The core clock controller generates clocks for the CPU, RPU (WiFi + BT +co-processor), audio, and several peripherals. + +Required properties: +- compatible: Must be "img,pistachio-clk". +- reg: Must contain the base address and length of the core clock controller. +- #clock-cells: Must be 1. The single cell is the clock identifier. + See dt-bindings/clock/pistachio-clk.h for the list of valid identifiers. +- clocks: Must contain an entry for each clock in clock-names. +- clock-names: Must include "xtal" (see "External clocks") and + "audio_clk_in_gate", "enet_clk_in_gate" which are generated by the + top-level general control. + +Example: + clk_core: clock-controller@18144000 { + compatible = "img,pistachio-clk"; + reg = <0x18144000 0x800>; + clocks = <&xtal>, <&cr_top EXT_CLK_AUDIO_IN>, + <&cr_top EXT_CLK_ENET_IN>; + clock-names = "xtal", "audio_clk_in_gate", "enet_clk_in_gate"; + + #clock-cells = <1>; + }; + +Peripheral clock controller: +---------------------------- + +The peripheral clock controller generates clocks for the DDR, ROM, and other +peripherals. The peripheral system clock ("periph_sys") generated by the core +clock controller is the input clock to the peripheral clock controller. + +Required properties: +- compatible: Must be "img,pistachio-periph-clk". +- reg: Must contain the base address and length of the peripheral clock + controller. +- #clock-cells: Must be 1. The single cell is the clock identifier. + See dt-bindings/clock/pistachio-clk.h for the list of valid identifiers. +- clocks: Must contain an entry for each clock in clock-names. +- clock-names: Must include "periph_sys", the peripheral system clock generated + by the core clock controller. + +Example: + clk_periph: clock-controller@18144800 { + compatible = "img,pistachio-clk-periph"; + reg = <0x18144800 0x800>; + clocks = <&clk_core CLK_PERIPH_SYS>; + clock-names = "periph_sys"; + + #clock-cells = <1>; + }; + +Peripheral general control: +--------------------------- + +The peripheral general control block generates system interface clocks and +resets for various peripherals. It also contains miscellaneous peripheral +control registers. The system clock ("sys") generated by the peripheral clock +controller is the input clock to the system clock controller. + +Required properties: +- compatible: Must include "img,pistachio-periph-cr" and "syscon". +- reg: Must contain the base address and length of the peripheral general + control registers. +- #clock-cells: Must be 1. The single cell is the clock identifier. + See dt-bindings/clock/pistachio-clk.h for the list of valid identifiers. +- clocks: Must contain an entry for each clock in clock-names. +- clock-names: Must include "sys", the system clock generated by the peripheral + clock controller. + +Example: + cr_periph: syscon@18144800 { + compatible = "img,pistachio-cr-periph", "syscon"; + reg = <0x18148000 0x1000>; + clocks = <&clock_periph PERIPH_CLK_PERIPH_SYS>; + clock-names = "sys"; + + #clock-cells = <1>; + }; + +Top-level general control: +-------------------------- + +The top-level general control block contains miscellaneous control registers and +gates for the external clocks "audio_clk_in" and "enet_clk_in". + +Required properties: +- compatible: Must include "img,pistachio-cr-top" and "syscon". +- reg: Must contain the base address and length of the top-level + control registers. +- clocks: Must contain an entry for each clock in clock-names. +- clock-names: Two optional clocks, "audio_clk_in" and "enet_clk_in" (see + "External clocks"). +- #clock-cells: Must be 1. The single cell is the clock identifier. + See dt-bindings/clock/pistachio-clk.h for the list of valid identifiers. + +Example: + cr_top: syscon@18144800 { + compatible = "img,pistachio-cr-top", "syscon"; + reg = <0x18149000 0x200>; + clocks = <&audio_refclk>, <&ext_enet_in>; + clock-names = "audio_clk_in", "enet_clk_in"; + + #clock-cells = <1>; + }; diff --git a/dts/Bindings/clock/pwm-clock.txt b/dts/Bindings/clock/pwm-clock.txt new file mode 100644 index 0000000000..83db876b3b --- /dev/null +++ b/dts/Bindings/clock/pwm-clock.txt @@ -0,0 +1,26 @@ +Binding for an external clock signal driven by a PWM pin. + +This binding uses the common clock binding[1] and the common PWM binding[2]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/pwm/pwm.txt + +Required properties: +- compatible : shall be "pwm-clock". +- #clock-cells : from common clock binding; shall be set to 0. +- pwms : from common PWM binding; this determines the clock frequency + via the period given in the PWM specifier. + +Optional properties: +- clock-output-names : From common clock binding. +- clock-frequency : Exact output frequency, in case the PWM period + is not exact but was rounded to nanoseconds. + +Example: + clock { + compatible = "pwm-clock"; + #clock-cells = <0>; + clock-frequency = <25000000>; + clock-output-names = "mipi_mclk"; + pwms = <&pwm2 0 40>; /* 1 / 40 ns = 25 MHz */ + }; diff --git a/dts/Bindings/clock/qcom,gcc.txt b/dts/Bindings/clock/qcom,gcc.txt index aba3d254e0..54c23f34f1 100644 --- a/dts/Bindings/clock/qcom,gcc.txt +++ b/dts/Bindings/clock/qcom,gcc.txt @@ -8,6 +8,7 @@ Required properties : "qcom,gcc-apq8084" "qcom,gcc-ipq8064" "qcom,gcc-msm8660" + "qcom,gcc-msm8916" "qcom,gcc-msm8960" "qcom,gcc-msm8974" "qcom,gcc-msm8974pro" diff --git a/dts/Bindings/clock/renesas,r8a7778-cpg-clocks.txt b/dts/Bindings/clock/renesas,r8a7778-cpg-clocks.txt new file mode 100644 index 0000000000..2f3747fdcf --- /dev/null +++ b/dts/Bindings/clock/renesas,r8a7778-cpg-clocks.txt @@ -0,0 +1,25 @@ +* Renesas R8A7778 Clock Pulse Generator (CPG) + +The CPG generates core clocks for the R8A7778. It includes two PLLs and +several fixed ratio dividers + +Required Properties: + + - compatible: Must be "renesas,r8a7778-cpg-clocks" + - reg: Base address and length of the memory resource used by the CPG + - #clock-cells: Must be 1 + - clock-output-names: The names of the clocks. Supported clocks are + "plla", "pllb", "b", "out", "p", "s", and "s1". + + +Example +------- + + cpg_clocks: cpg_clocks@ffc80000 { + compatible = "renesas,r8a7778-cpg-clocks"; + reg = <0xffc80000 0x80>; + #clock-cells = <1>; + clocks = <&extal_clk>; + clock-output-names = "plla", "pllb", "b", + "out", "p", "s", "s1"; + }; diff --git a/dts/Bindings/clock/sunxi.txt b/dts/Bindings/clock/sunxi.txt index 60b4428525..4fa11af3d3 100644 --- a/dts/Bindings/clock/sunxi.txt +++ b/dts/Bindings/clock/sunxi.txt @@ -20,6 +20,7 @@ Required properties: "allwinner,sun8i-a23-axi-clk" - for the AXI clock on A23 "allwinner,sun4i-a10-axi-gates-clk" - for the AXI gates "allwinner,sun4i-a10-ahb-clk" - for the AHB clock + "allwinner,sun5i-a13-ahb-clk" - for the AHB clock on A13 "allwinner,sun9i-a80-ahb-clk" - for the AHB bus clocks on A80 "allwinner,sun4i-a10-ahb-gates-clk" - for the AHB gates on A10 "allwinner,sun5i-a13-ahb-gates-clk" - for the AHB gates on A13 @@ -66,6 +67,8 @@ Required properties: "allwinner,sun4i-a10-usb-clk" - for usb gates + resets on A10 / A20 "allwinner,sun5i-a13-usb-clk" - for usb gates + resets on A13 "allwinner,sun6i-a31-usb-clk" - for usb gates + resets on A31 + "allwinner,sun9i-a80-usb-mod-clk" - for usb gates + resets on A80 + "allwinner,sun9i-a80-usb-phy-clk" - for usb phy gates + resets on A80 Required properties for all clocks: - reg : shall be the control register address for the clock. diff --git a/dts/Bindings/common-properties.txt b/dts/Bindings/common-properties.txt new file mode 100644 index 0000000000..3193979b1d --- /dev/null +++ b/dts/Bindings/common-properties.txt @@ -0,0 +1,60 @@ +Common properties + +The ePAPR specification does not define any properties related to hardware +byteswapping, but endianness issues show up frequently in porting Linux to +different machine types. This document attempts to provide a consistent +way of handling byteswapping across drivers. + +Optional properties: + - big-endian: Boolean; force big endian register accesses + unconditionally (e.g. ioread32be/iowrite32be). Use this if you + know the peripheral always needs to be accessed in BE mode. + - little-endian: Boolean; force little endian register accesses + unconditionally (e.g. readl/writel). Use this if you know the + peripheral always needs to be accessed in LE mode. + - native-endian: Boolean; always use register accesses matched to the + endianness of the kernel binary (e.g. LE vmlinux -> readl/writel, + BE vmlinux -> ioread32be/iowrite32be). In this case no byteswaps + will ever be performed. Use this if the hardware "self-adjusts" + register endianness based on the CPU's configured endianness. + +If a binding supports these properties, then the binding should also +specify the default behavior if none of these properties are present. +In such cases, little-endian is the preferred default, but it is not +a requirement. The of_device_is_big_endian() and of_fdt_is_big_endian() +helper functions do assume that little-endian is the default, because +most existing (PCI-based) drivers implicitly default to LE by using +readl/writel for MMIO accesses. + +Examples: +Scenario 1 : CPU in LE mode & device in LE mode. +dev: dev@40031000 { + compatible = "name"; + reg = <0x40031000 0x1000>; + ... + native-endian; +}; + +Scenario 2 : CPU in LE mode & device in BE mode. +dev: dev@40031000 { + compatible = "name"; + reg = <0x40031000 0x1000>; + ... + big-endian; +}; + +Scenario 3 : CPU in BE mode & device in BE mode. +dev: dev@40031000 { + compatible = "name"; + reg = <0x40031000 0x1000>; + ... + native-endian; +}; + +Scenario 4 : CPU in BE mode & device in LE mode. +dev: dev@40031000 { + compatible = "name"; + reg = <0x40031000 0x1000>; + ... + little-endian; +}; diff --git a/dts/Bindings/cris/axis.txt b/dts/Bindings/cris/axis.txt new file mode 100644 index 0000000000..d209ca2a47 --- /dev/null +++ b/dts/Bindings/cris/axis.txt @@ -0,0 +1,9 @@ +Axis Communications AB +ARTPEC series SoC Device Tree Bindings + + +CRISv32 based SoCs are ETRAX FS and ARTPEC-3: + + - compatible = "axis,crisv32"; + + diff --git a/dts/Bindings/cris/boards.txt b/dts/Bindings/cris/boards.txt new file mode 100644 index 0000000000..533dd273cc --- /dev/null +++ b/dts/Bindings/cris/boards.txt @@ -0,0 +1,8 @@ +Boards based on the CRIS SoCs: + +Required root node properties: + - compatible = should be one or more of the following: + - "axis,dev88" - for Axis devboard 88 with ETRAX FS + +Optional: + diff --git a/dts/Bindings/cris/interrupts.txt b/dts/Bindings/cris/interrupts.txt new file mode 100644 index 0000000000..e8b123b0a5 --- /dev/null +++ b/dts/Bindings/cris/interrupts.txt @@ -0,0 +1,23 @@ +* CRISv32 Interrupt Controller + +Interrupt controller for the CRISv32 SoCs. + +Main node required properties: + +- compatible : should be: + "axis,crisv32-intc" +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The type shall be a <u32> and the value shall be 1. +- reg: physical base address and size of the intc registers map. + +Example: + + intc: interrupt-controller { + compatible = "axis,crisv32-intc"; + reg = <0xb001c000 0x1000>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + diff --git a/dts/Bindings/crypto/img-hash.txt b/dts/Bindings/crypto/img-hash.txt new file mode 100644 index 0000000000..91a3d757d6 --- /dev/null +++ b/dts/Bindings/crypto/img-hash.txt @@ -0,0 +1,27 @@ +Imagination Technologies hardware hash accelerator + +The hash accelerator provides hardware hashing acceleration for +SHA1, SHA224, SHA256 and MD5 hashes + +Required properties: + +- compatible : "img,hash-accelerator" +- reg : Offset and length of the register set for the module, and the DMA port +- interrupts : The designated IRQ line for the hashing module. +- dmas : DMA specifier as per Documentation/devicetree/bindings/dma/dma.txt +- dma-names : Should be "tx" +- clocks : Clock specifiers +- clock-names : "sys" Used to clock the hash block registers + "hash" Used to clock data through the accelerator + +Example: + + hash: hash@18149600 { + compatible = "img,hash-accelerator"; + reg = <0x18149600 0x100>, <0x18101100 0x4>; + interrupts = <GIC_SHARED 59 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&dma 8 0xffffffff 0>; + dma-names = "tx"; + clocks = <&cr_periph SYS_CLK_HASH>, <&clk_periph PERIPH_CLK_ROM>; + clock-names = "sys", "hash"; + }; diff --git a/dts/Bindings/dma/apm-xgene-dma.txt b/dts/Bindings/dma/apm-xgene-dma.txt new file mode 100644 index 0000000000..d3058768b2 --- /dev/null +++ b/dts/Bindings/dma/apm-xgene-dma.txt @@ -0,0 +1,47 @@ +Applied Micro X-Gene SoC DMA nodes + +DMA nodes are defined to describe on-chip DMA interfaces in +APM X-Gene SoC. + +Required properties for DMA interfaces: +- compatible: Should be "apm,xgene-dma". +- device_type: set to "dma". +- reg: Address and length of the register set for the device. + It contains the information of registers in the following order: + 1st - DMA control and status register address space. + 2nd - Descriptor ring control and status register address space. + 3rd - Descriptor ring command register address space. + 4th - Soc efuse register address space. +- interrupts: DMA has 5 interrupts sources. 1st interrupt is + DMA error reporting interrupt. 2nd, 3rd, 4th and 5th interrupts + are completion interrupts for each DMA channels. +- clocks: Reference to the clock entry. + +Optional properties: +- dma-coherent : Present if dma operations are coherent + +Example: + dmaclk: dmaclk@1f27c000 { + compatible = "apm,xgene-device-clock"; + #clock-cells = <1>; + clocks = <&socplldiv2 0>; + reg = <0x0 0x1f27c000 0x0 0x1000>; + reg-names = "csr-reg"; + clock-output-names = "dmaclk"; + }; + + dma: dma@1f270000 { + compatible = "apm,xgene-storm-dma"; + device_type = "dma"; + reg = <0x0 0x1f270000 0x0 0x10000>, + <0x0 0x1f200000 0x0 0x10000>, + <0x0 0x1b008000 0x0 0x2000>, + <0x0 0x1054a000 0x0 0x100>; + interrupts = <0x0 0x82 0x4>, + <0x0 0xb8 0x4>, + <0x0 0xb9 0x4>, + <0x0 0xba 0x4>, + <0x0 0xbb 0x4>; + dma-coherent; + clocks = <&dmaclk 0>; + }; diff --git a/dts/Bindings/dma/bcm2835-dma.txt b/dts/Bindings/dma/brcm,bcm2835-dma.txt index 1396078d15..1396078d15 100644 --- a/dts/Bindings/dma/bcm2835-dma.txt +++ b/dts/Bindings/dma/brcm,bcm2835-dma.txt diff --git a/dts/Bindings/dma/jz4780-dma.txt b/dts/Bindings/dma/jz4780-dma.txt new file mode 100644 index 0000000000..f25feee62b --- /dev/null +++ b/dts/Bindings/dma/jz4780-dma.txt @@ -0,0 +1,56 @@ +* Ingenic JZ4780 DMA Controller + +Required properties: + +- compatible: Should be "ingenic,jz4780-dma" +- reg: Should contain the DMA controller registers location and length. +- interrupts: Should contain the interrupt specifier of the DMA controller. +- interrupt-parent: Should be the phandle of the interrupt controller that +- clocks: Should contain a clock specifier for the JZ4780 PDMA clock. +- #dma-cells: Must be <2>. Number of integer cells in the dmas property of + DMA clients (see below). + +Optional properties: + +- ingenic,reserved-channels: Bitmask of channels to reserve for devices that + need a specific channel. These channels will only be assigned when explicitly + requested by a client. The primary use for this is channels 0 and 1, which + can be configured to have special behaviour for NAND/BCH when using + programmable firmware. + +Example: + +dma: dma@13420000 { + compatible = "ingenic,jz4780-dma"; + reg = <0x13420000 0x10000>; + + interrupt-parent = <&intc>; + interrupts = <10>; + + clocks = <&cgu JZ4780_CLK_PDMA>; + + #dma-cells = <2>; + + ingenic,reserved-channels = <0x3>; +}; + +DMA clients must use the format described in dma.txt, giving a phandle to the +DMA controller plus the following 2 integer cells: + +1. Request type: The DMA request type for transfers to/from the device on + the allocated channel, as defined in the SoC documentation. + +2. Channel: If set to 0xffffffff, any available channel will be allocated for + the client. Otherwise, the exact channel specified will be used. The channel + should be reserved on the DMA controller using the ingenic,reserved-channels + property. + +Example: + +uart0: serial@10030000 { + ... + dmas = <&dma 0x14 0xffffffff + &dma 0x15 0xffffffff>; + dma-names = "tx", "rx"; + ... +}; diff --git a/dts/Bindings/dma/qcom_bam_dma.txt b/dts/Bindings/dma/qcom_bam_dma.txt index f8c3311b71..1c9d48ea49 100644 --- a/dts/Bindings/dma/qcom_bam_dma.txt +++ b/dts/Bindings/dma/qcom_bam_dma.txt @@ -4,6 +4,7 @@ Required properties: - compatible: must be one of the following: * "qcom,bam-v1.4.0" for MSM8974, APQ8074 and APQ8084 * "qcom,bam-v1.3.0" for APQ8064, IPQ8064 and MSM8960 + * "qcom,bam-v1.7.0" for MSM8916 - reg: Address range for DMA registers - interrupts: Should contain the one interrupt shared by all channels - #dma-cells: must be <1>, the cell in the dmas property of the client device diff --git a/dts/Bindings/dma/rcar-audmapp.txt b/dts/Bindings/dma/rcar-audmapp.txt deleted file mode 100644 index 61bca509d7..0000000000 --- a/dts/Bindings/dma/rcar-audmapp.txt +++ /dev/null @@ -1,29 +0,0 @@ -* R-Car Audio DMAC peri peri Device Tree bindings - -Required properties: -- compatible: should be "renesas,rcar-audmapp" -- #dma-cells: should be <1>, see "dmas" property below - -Example: - audmapp: audio-dma-pp@0xec740000 { - compatible = "renesas,rcar-audmapp"; - #dma-cells = <1>; - - reg = <0 0xec740000 0 0x200>; - }; - - -* DMA client - -Required properties: -- dmas: a list of <[DMA multiplexer phandle] [SRS << 8 | DRS]> pairs. - where SRS/DRS are specified in the SoC manual. - It will be written into PDMACHCR as high 16-bit parts. -- dma-names: a list of DMA channel names, one per "dmas" entry - -Example: - - dmas = <&audmapp 0x2d00 - &audmapp 0x3700>; - dma-names = "src0_ssiu0", - "dvc0_ssiu0"; diff --git a/dts/Bindings/dma/renesas,usb-dmac.txt b/dts/Bindings/dma/renesas,usb-dmac.txt new file mode 100644 index 0000000000..040f365954 --- /dev/null +++ b/dts/Bindings/dma/renesas,usb-dmac.txt @@ -0,0 +1,37 @@ +* Renesas USB DMA Controller Device Tree bindings + +Required Properties: +- compatible: must contain "renesas,usb-dmac" +- reg: base address and length of the registers block for the DMAC +- interrupts: interrupt specifiers for the DMAC, one for each entry in + interrupt-names. +- interrupt-names: one entry per channel, named "ch%u", where %u is the + channel number ranging from zero to the number of channels minus one. +- clocks: a list of phandle + clock-specifier pairs. +- #dma-cells: must be <1>, the cell specifies the channel number of the DMAC + port connected to the DMA client. +- dma-channels: number of DMA channels + +Example: R8A7790 (R-Car H2) USB-DMACs + + usb_dmac0: dma-controller@e65a0000 { + compatible = "renesas,usb-dmac"; + reg = <0 0xe65a0000 0 0x100>; + interrupts = <0 109 IRQ_TYPE_LEVEL_HIGH + 0 109 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "ch0", "ch1"; + clocks = <&mstp3_clks R8A7790_CLK_USBDMAC0>; + #dma-cells = <1>; + dma-channels = <2>; + }; + + usb_dmac1: dma-controller@e65b0000 { + compatible = "renesas,usb-dmac"; + reg = <0 0xe65b0000 0 0x100>; + interrupts = <0 110 IRQ_TYPE_LEVEL_HIGH + 0 110 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "ch0", "ch1"; + clocks = <&mstp3_clks R8A7790_CLK_USBDMAC1>; + #dma-cells = <1>; + dma-channels = <2>; + }; diff --git a/dts/Bindings/drm/imx/ldb.txt b/dts/Bindings/drm/imx/ldb.txt index 443bcb6134..9a21366436 100644 --- a/dts/Bindings/drm/imx/ldb.txt +++ b/dts/Bindings/drm/imx/ldb.txt @@ -44,23 +44,30 @@ Optional properties: LVDS Channel ============ -Each LVDS Channel has to contain a display-timings node that describes the -video timings for the connected LVDS display. For detailed information, also -have a look at Documentation/devicetree/bindings/video/display-timing.txt. +Each LVDS Channel has to contain either an of graph link to a panel device node +or a display-timings node that describes the video timings for the connected +LVDS display as well as the fsl,data-mapping and fsl,data-width properties. Required properties: - reg : should be <0> or <1> + - port: Input and output port nodes with endpoint definitions as defined in + Documentation/devicetree/bindings/graph.txt. + On i.MX5, the internal two-input-multiplexer is used. Due to hardware + limitations, only one input port (port@[0,1]) can be used for each channel + (lvds-channel@[0,1], respectively). + On i.MX6, there should be four input ports (port@[0-3]) that correspond + to the four LVDS multiplexer inputs. + A single output port (port@2 on i.MX5, port@4 on i.MX6) must be connected + to a panel input port. Optionally, the output port can be left out if + display-timings are used instead. + +Optional properties (required if display-timings are used): + - display-timings : A node that describes the display timings as defined in + Documentation/devicetree/bindings/video/display-timing.txt. - fsl,data-mapping : should be "spwg" or "jeida" This describes how the color bits are laid out in the serialized LVDS signal. - fsl,data-width : should be <18> or <24> - - port: A port node with endpoint definitions as defined in - Documentation/devicetree/bindings/media/video-interfaces.txt. - On i.MX5, the internal two-input-multiplexer is used. - Due to hardware limitations, only one port (port@[0,1]) - can be used for each channel (lvds-channel@[0,1], respectively) - On i.MX6, there should be four ports (port@[0-3]) that correspond - to the four LVDS multiplexer inputs. example: @@ -73,23 +80,21 @@ ldb: ldb@53fa8008 { #size-cells = <0>; compatible = "fsl,imx53-ldb"; gpr = <&gpr>; - clocks = <&clks 122>, <&clks 120>, - <&clks 115>, <&clks 116>, - <&clks 123>, <&clks 85>; + clocks = <&clks IMX5_CLK_LDB_DI0_SEL>, + <&clks IMX5_CLK_LDB_DI1_SEL>, + <&clks IMX5_CLK_IPU_DI0_SEL>, + <&clks IMX5_CLK_IPU_DI1_SEL>, + <&clks IMX5_CLK_LDB_DI0_GATE>, + <&clks IMX5_CLK_LDB_DI1_GATE>; clock-names = "di0_pll", "di1_pll", "di0_sel", "di1_sel", "di0", "di1"; + /* Using an of-graph endpoint link to connect the panel */ lvds-channel@0 { #address-cells = <1>; #size-cells = <0>; reg = <0>; - fsl,data-mapping = "spwg"; - fsl,data-width = <24>; - - display-timings { - /* ... */ - }; port@0 { reg = <0>; @@ -98,8 +103,17 @@ ldb: ldb@53fa8008 { remote-endpoint = <&ipu_di0_lvds0>; }; }; + + port@2 { + reg = <2>; + + lvds0_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; }; + /* Using display-timings and fsl,data-mapping/width instead */ lvds-channel@1 { #address-cells = <1>; #size-cells = <0>; @@ -120,3 +134,13 @@ ldb: ldb@53fa8008 { }; }; }; + +panel: lvds-panel { + /* ... */ + + port { + panel_in: endpoint { + remote-endpoint = <&lvds0_out>; + }; + }; +}; diff --git a/dts/Bindings/extcon/extcon-usb-gpio.txt b/dts/Bindings/extcon/extcon-usb-gpio.txt new file mode 100644 index 0000000000..af0b903de2 --- /dev/null +++ b/dts/Bindings/extcon/extcon-usb-gpio.txt @@ -0,0 +1,18 @@ +USB GPIO Extcon device + +This is a virtual device used to generate USB cable states from the USB ID pin +connected to a GPIO pin. + +Required properties: +- compatible: Should be "linux,extcon-usb-gpio" +- id-gpio: gpio for USB ID pin. See gpio binding. + +Example: Examples of extcon-usb-gpio node in dra7-evm.dts as listed below: + extcon_usb1 { + compatible = "linux,extcon-usb-gpio"; + id-gpio = <&gpio6 1 GPIO_ACTIVE_HIGH>; + } + + &omap_dwc3_1 { + extcon = <&extcon_usb1>; + }; diff --git a/dts/Bindings/gpio/gpio-bcm-kona.txt b/dts/Bindings/gpio/brcm,kona-gpio.txt index 4a63bc96b6..4a63bc96b6 100644 --- a/dts/Bindings/gpio/gpio-bcm-kona.txt +++ b/dts/Bindings/gpio/brcm,kona-gpio.txt diff --git a/dts/Bindings/gpio/gpio-altera.txt b/dts/Bindings/gpio/gpio-altera.txt new file mode 100644 index 0000000000..12f50149e1 --- /dev/null +++ b/dts/Bindings/gpio/gpio-altera.txt @@ -0,0 +1,43 @@ +Altera GPIO controller bindings + +Required properties: +- compatible: + - "altr,pio-1.0" +- reg: Physical base address and length of the controller's registers. +- #gpio-cells : Should be 2 + - The first cell is the gpio offset number. + - The second cell is reserved and is currently unused. +- gpio-controller : Marks the device node as a GPIO controller. +- interrupt-controller: Mark the device node as an interrupt controller +- #interrupt-cells : Should be 1. The interrupt type is fixed in the hardware. + - The first cell is the GPIO offset number within the GPIO controller. +- interrupts: Specify the interrupt. +- altr,interrupt-trigger: Specifies the interrupt trigger type the GPIO + hardware is synthesized. This field is required if the Altera GPIO controller + used has IRQ enabled as the interrupt type is not software controlled, + but hardware synthesized. Required if GPIO is used as an interrupt + controller. The value is defined in <dt-bindings/interrupt-controller/irq.h> + Only the following flags are supported: + IRQ_TYPE_EDGE_RISING + IRQ_TYPE_EDGE_FALLING + IRQ_TYPE_EDGE_BOTH + IRQ_TYPE_LEVEL_HIGH + +Optional properties: +- altr,ngpio: Width of the GPIO bank. This defines how many pins the + GPIO device has. Ranges between 1-32. Optional and defaults to 32 if not + specified. + +Example: + +gpio_altr: gpio@0xff200000 { + compatible = "altr,pio-1.0"; + reg = <0xff200000 0x10>; + interrupts = <0 45 4>; + altr,ngpio = <32>; + altr,interrupt-trigger = <IRQ_TYPE_EDGE_RISING>; + #gpio-cells = <2>; + gpio-controller; + #interrupt-cells = <1>; + interrupt-controller; +}; diff --git a/dts/Bindings/gpio/gpio-fan.txt b/dts/Bindings/gpio/gpio-fan.txt index 2dd457a346..439a7430fc 100644 --- a/dts/Bindings/gpio/gpio-fan.txt +++ b/dts/Bindings/gpio/gpio-fan.txt @@ -2,15 +2,20 @@ Bindings for fan connected to GPIO lines Required properties: - compatible : "gpio-fan" + +Optional properties: - gpios: Specifies the pins that map to bits in the control value, ordered MSB-->LSB. - gpio-fan,speed-map: A mapping of possible fan RPM speeds and the control value that should be set to achieve them. This array must have the RPM values in ascending order. - -Optional properties: - alarm-gpios: This pin going active indicates something is wrong with the fan, and a udev event will be fired. +- cooling-cells: If used as a cooling device, must be <2> + Also see: Documentation/devicetree/bindings/thermal/thermal.txt + min and max states are derived from the speed-map of the fan. + +Note: At least one the "gpios" or "alarm-gpios" properties must be set. Examples: @@ -23,3 +28,13 @@ Examples: 6000 2>; alarm-gpios = <&gpio1 15 1>; }; + gpio_fan_cool: gpio_fan { + compatible = "gpio-fan"; + gpios = <&gpio2 14 1 + &gpio2 13 1>; + gpio-fan,speed-map = <0 0>, + <3000 1>, + <6000 2>; + alarm-gpios = <&gpio2 15 1>; + #cooling-cells = <2>; /* min followed by max */ + }; diff --git a/dts/Bindings/gpio/gpio.txt b/dts/Bindings/gpio/gpio.txt index f7a158d858..5788d5cf12 100644 --- a/dts/Bindings/gpio/gpio.txt +++ b/dts/Bindings/gpio/gpio.txt @@ -116,6 +116,29 @@ Every GPIO controller node must contain both an empty "gpio-controller" property, and a #gpio-cells integer property, which indicates the number of cells in a gpio-specifier. +The GPIO chip may contain GPIO hog definitions. GPIO hogging is a mechanism +providing automatic GPIO request and configuration as part of the +gpio-controller's driver probe function. + +Each GPIO hog definition is represented as a child node of the GPIO controller. +Required properties: +- gpio-hog: A property specifying that this child node represent a GPIO hog. +- gpios: Store the GPIO information (id, flags, ...). Shall contain the + number of cells specified in its parent node (GPIO controller + node). +Only one of the following properties scanned in the order shown below. +This means that when multiple properties are present they will be searched +in the order presented below and the first match is taken as the intended +configuration. +- input: A property specifying to set the GPIO direction as input. +- output-low A property specifying to set the GPIO direction as output with + the value low. +- output-high A property specifying to set the GPIO direction as output with + the value high. + +Optional properties: +- line-name: The GPIO label name. If not present the node name is used. + Example of two SOC GPIO banks defined as gpio-controller nodes: qe_pio_a: gpio-controller@1400 { @@ -123,6 +146,13 @@ Example of two SOC GPIO banks defined as gpio-controller nodes: reg = <0x1400 0x18>; gpio-controller; #gpio-cells = <2>; + + line_b { + gpio-hog; + gpios = <6 0>; + output-low; + line-name = "foo-bar-gpio"; + }; }; qe_pio_e: gpio-controller@1460 { diff --git a/dts/Bindings/gpio/mrvl-gpio.txt b/dts/Bindings/gpio/mrvl-gpio.txt index 67a2e4e414..98d1983969 100644 --- a/dts/Bindings/gpio/mrvl-gpio.txt +++ b/dts/Bindings/gpio/mrvl-gpio.txt @@ -12,7 +12,7 @@ Required properties: gpio_mux. - interrupt-names : Should be the names of irq resources. Each interrupt uses its own interrupt name, so there should be as many interrupt names - as referenced interrups. + as referenced interrupts. - interrupt-controller : Identifies the node as an interrupt controller. - #interrupt-cells: Specifies the number of cells needed to encode an interrupt source. diff --git a/dts/Bindings/hwrng/brcm,iproc-rng200.txt b/dts/Bindings/hwrng/brcm,iproc-rng200.txt new file mode 100644 index 0000000000..e25a456664 --- /dev/null +++ b/dts/Bindings/hwrng/brcm,iproc-rng200.txt @@ -0,0 +1,12 @@ +HWRNG support for the iproc-rng200 driver + +Required properties: +- compatible : "brcm,iproc-rng200" +- reg : base address and size of control register block + +Example: + +rng { + compatible = "brcm,iproc-rng200"; + reg = <0x18032000 0x28>; +}; diff --git a/dts/Bindings/i2c/i2c-bcm-kona.txt b/dts/Bindings/i2c/brcm,kona-i2c.txt index 1b87b741fa..1b87b741fa 100644 --- a/dts/Bindings/i2c/i2c-bcm-kona.txt +++ b/dts/Bindings/i2c/brcm,kona-i2c.txt diff --git a/dts/Bindings/i2c/i2c-davinci.txt b/dts/Bindings/i2c/i2c-davinci.txt index 2dc935b411..a4e1cbc810 100644 --- a/dts/Bindings/i2c/i2c-davinci.txt +++ b/dts/Bindings/i2c/i2c-davinci.txt @@ -10,6 +10,9 @@ Required properties: Recommended properties : - interrupts : standard interrupt property. - clock-frequency : desired I2C bus clock frequency in Hz. +- ti,has-pfunc: boolean; if defined, it indicates that SoC supports PFUNC + registers. PFUNC registers allow to switch I2C pins to function as + GPIOs, so they can by toggled manually. Example (enbw_cmc board): i2c@1c22000 { diff --git a/dts/Bindings/i2c/i2c-digicolor.txt b/dts/Bindings/i2c/i2c-digicolor.txt new file mode 100644 index 0000000000..457a098d4f --- /dev/null +++ b/dts/Bindings/i2c/i2c-digicolor.txt @@ -0,0 +1,25 @@ +Conexant Digicolor I2C controller + +Required properties: + - compatible: must be "cnxt,cx92755-i2c" + - reg: physical address and length of the device registers + - interrupts: a single interrupt specifier + - clocks: clock for the device + - #address-cells: should be <1> + - #size-cells: should be <0> + +Optional properties: +- clock-frequency: the desired I2C bus clock frequency in Hz; in + absence of this property the default value is used (100 kHz). + +Example: + + i2c: i2c@f0000120 { + compatible = "cnxt,cx92755-i2c"; + reg = <0xf0000120 0x10>; + interrupts = <28>; + clocks = <&main_clk>; + clock-frequency = <100000>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/dts/Bindings/i2c/i2c-jz4780.txt b/dts/Bindings/i2c/i2c-jz4780.txt new file mode 100644 index 0000000000..231e4cc400 --- /dev/null +++ b/dts/Bindings/i2c/i2c-jz4780.txt @@ -0,0 +1,35 @@ +* Ingenic JZ4780 I2C Bus controller + +Required properties: +- compatible: should be "ingenic,jz4780-i2c" +- reg: Should contain the address & size of the I2C controller registers. +- interrupts: Should specify the interrupt provided by parent. +- clocks: Should contain a single clock specifier for the JZ4780 I2C clock. +- clock-frequency: desired I2C bus clock frequency in Hz. + +Recommended properties: +- pinctrl-names: should be "default"; +- pinctrl-0: phandle to pinctrl function + +Optional properties: +- interrupt-parent: Should be the phandle of the interrupt controller that + delivers interrupts to the I2C block. + +Example + +/ { + i2c4: i2c4@0x10054000 { + compatible = "ingenic,jz4780-i2c"; + reg = <0x10054000 0x1000>; + + interrupt-parent = <&intc>; + interrupts = <56>; + + clocks = <&cgu JZ4780_CLK_SMB4>; + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pins_i2c4_data>; + + }; +}; + diff --git a/dts/Bindings/i2c/i2c-xlp9xx.txt b/dts/Bindings/i2c/i2c-xlp9xx.txt new file mode 100644 index 0000000000..f818ef507a --- /dev/null +++ b/dts/Bindings/i2c/i2c-xlp9xx.txt @@ -0,0 +1,22 @@ +Device tree configuration for the I2C controller on the XLP9xx/5xx SoC + +Required properties: +- compatible : should be "netlogic,xlp980-i2c" +- reg : bus address start and address range size of device +- interrupts : interrupt number + +Optional properties: +- clock-frequency : frequency of bus clock in Hz + Defaults to 100 KHz when the property is not specified + +Example: + +i2c0: i2c@113100 { + compatible = "netlogic,xlp980-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0 0x113100 0x100>; + clock-frequency = <400000>; + interrupts = <30>; + interrupt-parent = <&pic>; +}; diff --git a/dts/Bindings/i2c/trivial-devices.txt b/dts/Bindings/i2c/trivial-devices.txt index aaa8325004..ad0c4ac916 100644 --- a/dts/Bindings/i2c/trivial-devices.txt +++ b/dts/Bindings/i2c/trivial-devices.txt @@ -77,6 +77,7 @@ nxp,pca9556 Octal SMBus and I2C registered interface nxp,pca9557 8-bit I2C-bus and SMBus I/O port with reset nxp,pcf8563 Real-time clock/calendar nxp,pcf85063 Tiny Real-Time Clock +oki,ml86v7667 OKI ML86V7667 video decoder ovti,ov5642 OV5642: Color CMOS QSXGA (5-megapixel) Image Sensor with OmniBSI and Embedded TrueFocus pericom,pt7c4338 Real-time Clock Module plx,pex8648 48-Lane, 12-Port PCI Express Gen 2 (5.0 GT/s) Switch @@ -89,6 +90,7 @@ ricoh,rv5c386 I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC ricoh,rv5c387a I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC samsung,24ad0xd1 S524AD0XF1 (128K/256K-bit Serial EEPROM for Low Power) sii,s35390a 2-wire CMOS real-time clock +skyworks,sky81452 Skyworks SKY81452: Six-Channel White LED Driver with Touch Panel Bias Supply st-micro,24c256 i2c serial eeprom (24cxx) stm,m41t00 Serial Access TIMEKEEPER stm,m41t62 Serial real-time clock (RTC) with alarm diff --git a/dts/Bindings/iio/adc/da9150-gpadc.txt b/dts/Bindings/iio/adc/da9150-gpadc.txt new file mode 100644 index 0000000000..c07228da92 --- /dev/null +++ b/dts/Bindings/iio/adc/da9150-gpadc.txt @@ -0,0 +1,16 @@ +Dialog Semiconductor DA9150 IIO GPADC bindings + +Required properties: +- compatible: "dlg,da9150-gpadc" for DA9150 IIO GPADC +- #io-channel-cells: Should be set to <1> + (See Documentation/devicetree/bindings/iio/iio-bindings.txt for further info) + +For further information on GPADC channels, see device datasheet. + + +Example: + + gpadc: da9150-gpadc { + compatible = "dlg,da9150-gpadc"; + #io-channel-cells = <1>; + }; diff --git a/dts/Bindings/iio/adc/mcp320x.txt b/dts/Bindings/iio/adc/mcp320x.txt new file mode 100644 index 0000000000..b85184391b --- /dev/null +++ b/dts/Bindings/iio/adc/mcp320x.txt @@ -0,0 +1,30 @@ +* Microchip Analog to Digital Converter (ADC) + +The node for this driver must be a child node of a SPI controller, hence +all mandatory properties described in + + Documentation/devicetree/bindings/spi/spi-bus.txt + +must be specified. + +Required properties: + - compatible: Must be one of the following, depending on the + model: + "mcp3001" + "mcp3002" + "mcp3004" + "mcp3008" + "mcp3201" + "mcp3202" + "mcp3204" + "mcp3208" + + +Examples: +spi_controller { + mcp3x0x@0 { + compatible = "mcp3002"; + reg = <0>; + spi-max-frequency = <1000000>; + }; +}; diff --git a/dts/Bindings/iio/adc/mcp3422.txt b/dts/Bindings/iio/adc/mcp3422.txt new file mode 100644 index 0000000000..333139cc0b --- /dev/null +++ b/dts/Bindings/iio/adc/mcp3422.txt @@ -0,0 +1,17 @@ +* Microchip mcp3422/3/4/6/7/8 chip family (ADC) + +Required properties: + - compatible: Should be + "microchip,mcp3422" or + "microchip,mcp3423" or + "microchip,mcp3424" or + "microchip,mcp3426" or + "microchip,mcp3427" or + "microchip,mcp3428" + - reg: I2C address for the device + +Example: +adc@0 { + compatible = "microchip,mcp3424"; + reg = <0x68>; +}; diff --git a/dts/Bindings/iio/adc/ti-adc128s052.txt b/dts/Bindings/iio/adc/ti-adc128s052.txt new file mode 100644 index 0000000000..42ca7deec9 --- /dev/null +++ b/dts/Bindings/iio/adc/ti-adc128s052.txt @@ -0,0 +1,18 @@ +* Texas Instruments' ADC128S052 ADC chip + +Required properties: + - compatible: Should be "ti,adc128s052" + - reg: spi chip select number for the device + - vref-supply: The regulator supply for ADC reference voltage + +Recommended properties: + - spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: +adc@0 { + compatible = "ti,adc128s052"; + reg = <0>; + vref-supply = <&vdd_supply>; + spi-max-frequency = <1000000>; +}; diff --git a/dts/Bindings/iio/st-sensors.txt b/dts/Bindings/iio/st-sensors.txt index a7a0a15913..d2aaca9745 100644 --- a/dts/Bindings/iio/st-sensors.txt +++ b/dts/Bindings/iio/st-sensors.txt @@ -23,6 +23,7 @@ standard bindings from pinctrl/pinctrl-bindings.txt. Valid compatible strings: Accelerometers: +- st,lis3lv02dl-accel - st,lsm303dlh-accel - st,lsm303dlhc-accel - st,lis3dh-accel diff --git a/dts/Bindings/input/brcm,bcm-keypad.txt b/dts/Bindings/input/brcm,bcm-keypad.txt new file mode 100644 index 0000000000..b77f50bd64 --- /dev/null +++ b/dts/Bindings/input/brcm,bcm-keypad.txt @@ -0,0 +1,108 @@ +* Broadcom Keypad Controller device tree bindings + +Broadcom Keypad controller is used to interface a SoC with a matrix-type +keypad device. The keypad controller supports multiple row and column lines. +A key can be placed at each intersection of a unique row and a unique column. +The keypad controller can sense a key-press and key-release and report the +event using a interrupt to the cpu. + +This binding is based on the matrix-keymap binding with the following +changes: + +keypad,num-rows and keypad,num-columns are required. + +Required SoC Specific Properties: +- compatible: should be "brcm,bcm-keypad" + +- reg: physical base address of the controller and length of memory mapped + region. + +- interrupts: The interrupt number to the cpu. + +Board Specific Properties: +- keypad,num-rows: Number of row lines connected to the keypad + controller. + +- keypad,num-columns: Number of column lines connected to the + keypad controller. + +- col-debounce-filter-period: The debounce period for the Column filter. + + KEYPAD_DEBOUNCE_1_ms = 0 + KEYPAD_DEBOUNCE_2_ms = 1 + KEYPAD_DEBOUNCE_4_ms = 2 + KEYPAD_DEBOUNCE_8_ms = 3 + KEYPAD_DEBOUNCE_16_ms = 4 + KEYPAD_DEBOUNCE_32_ms = 5 + KEYPAD_DEBOUNCE_64_ms = 6 + KEYPAD_DEBOUNCE_128_ms = 7 + +- status-debounce-filter-period: The debounce period for the Status filter. + + KEYPAD_DEBOUNCE_1_ms = 0 + KEYPAD_DEBOUNCE_2_ms = 1 + KEYPAD_DEBOUNCE_4_ms = 2 + KEYPAD_DEBOUNCE_8_ms = 3 + KEYPAD_DEBOUNCE_16_ms = 4 + KEYPAD_DEBOUNCE_32_ms = 5 + KEYPAD_DEBOUNCE_64_ms = 6 + KEYPAD_DEBOUNCE_128_ms = 7 + +- row-output-enabled: An optional property indicating whether the row or + column is being used as output. If specified the row is being used + as the output. Else defaults to column. + +- pull-up-enabled: An optional property indicating the Keypad scan mode. + If specified implies the keypad scan pull-up has been enabled. + +- autorepeat: Boolean, Enable auto repeat feature of Linux input + subsystem (optional). + +- linux,keymap: The keymap for keys as described in the binding document + devicetree/bindings/input/matrix-keymap.txt. + +Example: +#include "dt-bindings/input/input.h" + +/ { + keypad: keypad@180ac000 { + /* Required SoC specific properties */ + compatible = "brcm,bcm-keypad"; + + /* Required Board specific properties */ + keypad,num-rows = <5>; + keypad,num-columns = <5>; + status = "okay"; + + linux,keymap = <MATRIX_KEY(0x00, 0x02, KEY_F) /* key_forward */ + MATRIX_KEY(0x00, 0x03, KEY_HOME) /* key_home */ + MATRIX_KEY(0x00, 0x04, KEY_M) /* key_message */ + MATRIX_KEY(0x01, 0x00, KEY_A) /* key_contacts */ + MATRIX_KEY(0x01, 0x01, KEY_1) /* key_1 */ + MATRIX_KEY(0x01, 0x02, KEY_2) /* key_2 */ + MATRIX_KEY(0x01, 0x03, KEY_3) /* key_3 */ + MATRIX_KEY(0x01, 0x04, KEY_S) /* key_speaker */ + MATRIX_KEY(0x02, 0x00, KEY_P) /* key_phone */ + MATRIX_KEY(0x02, 0x01, KEY_4) /* key_4 */ + MATRIX_KEY(0x02, 0x02, KEY_5) /* key_5 */ + MATRIX_KEY(0x02, 0x03, KEY_6) /* key_6 */ + MATRIX_KEY(0x02, 0x04, KEY_VOLUMEUP) /* key_vol_up */ + MATRIX_KEY(0x03, 0x00, KEY_C) /* key_call_log */ + MATRIX_KEY(0x03, 0x01, KEY_7) /* key_7 */ + MATRIX_KEY(0x03, 0x02, KEY_8) /* key_8 */ + MATRIX_KEY(0x03, 0x03, KEY_9) /* key_9 */ + MATRIX_KEY(0x03, 0x04, KEY_VOLUMEDOWN) /* key_vol_down */ + MATRIX_KEY(0x04, 0x00, KEY_H) /* key_headset */ + MATRIX_KEY(0x04, 0x01, KEY_KPASTERISK) /* key_* */ + MATRIX_KEY(0x04, 0x02, KEY_0) /* key_0 */ + MATRIX_KEY(0x04, 0x03, KEY_GRAVE) /* key_# */ + MATRIX_KEY(0x04, 0x04, KEY_MUTE) /* key_mute */ + >; + + /* Optional board specific properties */ + col-debounce-filter-period = <5>; + row-output-enabled; + pull-up-enabled; + + }; +}; diff --git a/dts/Bindings/input/qcom,pm8941-pwrkey.txt b/dts/Bindings/input/qcom,pm8941-pwrkey.txt new file mode 100644 index 0000000000..07bf55f6e0 --- /dev/null +++ b/dts/Bindings/input/qcom,pm8941-pwrkey.txt @@ -0,0 +1,43 @@ +Qualcomm PM8941 PMIC Power Key + +PROPERTIES + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,pm8941-pwrkey" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: base address of registers for block + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: key change interrupt; The format of the specifier is + defined by the binding document describing the node's + interrupt parent. + +- debounce: + Usage: optional + Value type: <u32> + Definition: time in microseconds that key must be pressed or released + for state change interrupt to trigger. + +- bias-pull-up: + Usage: optional + Value type: <empty> + Definition: presence of this property indicates that the KPDPWR_N pin + should be configured for pull up. + +EXAMPLE + + pwrkey@800 { + compatible = "qcom,pm8941-pwrkey"; + reg = <0x800>; + interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>; + debounce = <15625>; + bias-pull-up; + }; diff --git a/dts/Bindings/input/touchscreen/brcm,iproc-touchscreen.txt b/dts/Bindings/input/touchscreen/brcm,iproc-touchscreen.txt new file mode 100644 index 0000000000..34e3382a06 --- /dev/null +++ b/dts/Bindings/input/touchscreen/brcm,iproc-touchscreen.txt @@ -0,0 +1,76 @@ +* Broadcom's IPROC Touchscreen Controller + +Required properties: +- compatible: must be "brcm,iproc-touchscreen" +- reg: physical base address of the controller and length of memory mapped + region. +- clocks: The clock provided by the SOC to driver the tsc +- clock-name: name for the clock +- interrupts: The touchscreen controller's interrupt + +Optional properties: +- scanning_period: Time between scans. Each step is 1024 us. Valid 1-256. +- debounce_timeout: Each step is 512 us. Valid 0-255 +- settling_timeout: The settling duration (in ms) is the amount of time + the tsc waits to allow the voltage to settle after + turning on the drivers in detection mode. + Valid values: 0-11 + 0 = 0.008 ms + 1 = 0.01 ms + 2 = 0.02 ms + 3 = 0.04 ms + 4 = 0.08 ms + 5 = 0.16 ms + 6 = 0.32 ms + 7 = 0.64 ms + 8 = 1.28 ms + 9 = 2.56 ms + 10 = 5.12 ms + 11 = 10.24 ms +- touch_timeout: The continuous number of scan periods in which touch is + not detected before the controller returns to idle state. + Valid values 0-255. +- average_data: Number of data samples which are averaged before a final + data point is placed into the FIFO + Valid values 0-7 + 0 = 1 sample + 1 = 2 samples + 2 = 4 samples + 3 = 8 samples + 4 = 16 samples + 5 = 32 samples + 6 = 64 samples + 7 = 128 samples +- fifo_threshold: Interrupt is generated whenever the number of fifo + entries exceeds this value + Valid values 0-31 +- touchscreen-size-x: horizontal resolution of touchscreen (in pixels) +- touchscreen-size-y: vertical resolution of touchscreen (in pixels) +- touchscreen-fuzz-x: horizontal noise value of the absolute input + device (in pixels) +- touchscreen-fuzz-y: vertical noise value of the absolute input + device (in pixels) +- touchscreen-inverted-x: X axis is inverted (boolean) +- touchscreen-inverted-y: Y axis is inverted (boolean) + +Example: + + touchscreen: tsc@0x180A6000 { + compatible = "brcm,iproc-touchscreen"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x180A6000 0x40>; + clocks = <&adc_clk>; + clock-names = "tsc_clk"; + interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>; + + scanning_period = <5>; + debounce_timeout = <40>; + settling_timeout = <7>; + touch_timeout = <10>; + average_data = <5>; + fifo_threshold = <1>; + /* Touchscreen is rotated 180 degrees. */ + touchscreen-inverted-x; + touchscreen-inverted-y; + }; diff --git a/dts/Bindings/input/touchscreen/chipone_icn8318.txt b/dts/Bindings/input/touchscreen/chipone_icn8318.txt new file mode 100644 index 0000000000..d11f8d615b --- /dev/null +++ b/dts/Bindings/input/touchscreen/chipone_icn8318.txt @@ -0,0 +1,46 @@ +* ChipOne icn8318 I2C touchscreen controller + +Required properties: + - compatible : "chipone,icn8318" + - reg : I2C slave address of the chip (0x40) + - interrupt-parent : a phandle pointing to the interrupt controller + serving the interrupt for this chip + - interrupts : interrupt specification for the icn8318 interrupt + - wake-gpios : GPIO specification for the WAKE input + - touchscreen-size-x : horizontal resolution of touchscreen (in pixels) + - touchscreen-size-y : vertical resolution of touchscreen (in pixels) + +Optional properties: + - pinctrl-names : should be "default" + - pinctrl-0: : a phandle pointing to the pin settings for the + control gpios + - touchscreen-fuzz-x : horizontal noise value of the absolute input + device (in pixels) + - touchscreen-fuzz-y : vertical noise value of the absolute input + device (in pixels) + - touchscreen-inverted-x : X axis is inverted (boolean) + - touchscreen-inverted-y : Y axis is inverted (boolean) + - touchscreen-swapped-x-y : X and Y axis are swapped (boolean) + Swapping is done after inverting the axis + +Example: + +i2c@00000000 { + /* ... */ + + chipone_icn8318@40 { + compatible = "chipone,icn8318"; + reg = <0x40>; + interrupt-parent = <&pio>; + interrupts = <9 IRQ_TYPE_EDGE_FALLING>; /* EINT9 (PG9) */ + pinctrl-names = "default"; + pinctrl-0 = <&ts_wake_pin_p66>; + wake-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */ + touchscreen-size-x = <800>; + touchscreen-size-y = <480>; + touchscreen-inverted-x; + touchscreen-swapped-x-y; + }; + + /* ... */ +}; diff --git a/dts/Bindings/input/touchscreen/goodix.txt b/dts/Bindings/input/touchscreen/goodix.txt new file mode 100644 index 0000000000..8ba98eec76 --- /dev/null +++ b/dts/Bindings/input/touchscreen/goodix.txt @@ -0,0 +1,29 @@ +Device tree bindings for Goodix GT9xx series touchscreen controller + +Required properties: + + - compatible : Should be "goodix,gt911" + or "goodix,gt9110" + or "goodix,gt912" + or "goodix,gt927" + or "goodix,gt9271" + or "goodix,gt928" + or "goodix,gt967" + - reg : I2C address of the chip. Should be 0x5d or 0x14 + - interrupt-parent : Interrupt controller to which the chip is connected + - interrupts : Interrupt to which the chip is connected + +Example: + + i2c@00000000 { + /* ... */ + + gt928@5d { + compatible = "goodix,gt928"; + reg = <0x5d>; + interrupt-parent = <&gpio>; + interrupts = <0 0>; + }; + + /* ... */ + }; diff --git a/dts/Bindings/input/touchscreen/sun4i.txt b/dts/Bindings/input/touchscreen/sun4i.txt index 433332d3b2..89abecd938 100644 --- a/dts/Bindings/input/touchscreen/sun4i.txt +++ b/dts/Bindings/input/touchscreen/sun4i.txt @@ -2,14 +2,27 @@ sun4i resistive touchscreen controller -------------------------------------- Required properties: - - compatible: "allwinner,sun4i-a10-ts" or "allwinner,sun6i-a31-ts" + - compatible: "allwinner,sun4i-a10-ts", "allwinner,sun5i-a13-ts" or + "allwinner,sun6i-a31-ts" - reg: mmio address range of the chip - interrupts: interrupt to which the chip is connected - #thermal-sensor-cells: shall be 0 Optional properties: - - allwinner,ts-attached: boolean indicating that an actual touchscreen is - attached to the controller + - allwinner,ts-attached : boolean indicating that an actual touchscreen + is attached to the controller + - allwinner,tp-sensitive-adjust : integer (4 bits) + adjust sensitivity of pen down detection + between 0 (least sensitive) and 15 + (defaults to 15) + - allwinner,filter-type : integer (2 bits) + select median and averaging filter + samples used for median / averaging filter + 0: 4/2 + 1: 5/3 + 2: 8/4 + 3: 16/8 + (defaults to 1) Example: @@ -19,4 +32,7 @@ Example: interrupts = <29>; allwinner,ts-attached; #thermal-sensor-cells = <0>; + /* sensitive/noisy touch panel */ + allwinner,tp-sensitive-adjust = <0>; + allwinner,filter-type = <3>; }; diff --git a/dts/Bindings/input/touchscreen/sx8654.txt b/dts/Bindings/input/touchscreen/sx8654.txt new file mode 100644 index 0000000000..5aaa6b3aa9 --- /dev/null +++ b/dts/Bindings/input/touchscreen/sx8654.txt @@ -0,0 +1,16 @@ +* Semtech SX8654 I2C Touchscreen Controller + +Required properties: +- compatible: must be "semtech,sx8654" +- reg: i2c slave address +- interrupt-parent: the phandle for the interrupt controller +- interrupts: touch controller interrupt + +Example: + + sx8654@48 { + compatible = "semtech,sx8654"; + reg = <0x48>; + interrupt-parent = <&gpio6>; + interrupts = <3 IRQ_TYPE_EDGE_FALLING>; + }; diff --git a/dts/Bindings/input/touchscreen/touchscreen.txt b/dts/Bindings/input/touchscreen/touchscreen.txt index d8e06163c5..ac23caf518 100644 --- a/dts/Bindings/input/touchscreen/touchscreen.txt +++ b/dts/Bindings/input/touchscreen/touchscreen.txt @@ -16,6 +16,8 @@ Optional properties for Touchscreens: controller) - touchscreen-inverted-x : X axis is inverted (boolean) - touchscreen-inverted-y : Y axis is inverted (boolean) + - touchscreen-swapped-x-y : X and Y axis are swapped (boolean) + Swapping is done after inverting the axis Deprecated properties for Touchscreens: - x-size : deprecated name for touchscreen-size-x diff --git a/dts/Bindings/interrupt-controller/brcm,bcm3380-l2-intc.txt b/dts/Bindings/interrupt-controller/brcm,bcm3380-l2-intc.txt new file mode 100644 index 0000000000..8f48aad508 --- /dev/null +++ b/dts/Bindings/interrupt-controller/brcm,bcm3380-l2-intc.txt @@ -0,0 +1,41 @@ +Broadcom BCM3380-style Level 1 / Level 2 interrupt controller + +This interrupt controller shows up in various forms on many BCM338x/BCM63xx +chipsets. It has the following properties: + +- outputs a single interrupt signal to its interrupt controller parent + +- contains one or more enable/status word pairs, which often appear at + different offsets in different blocks + +- no atomic set/clear operations + +Required properties: + +- compatible: should be "brcm,bcm3380-l2-intc" +- reg: specifies one or more enable/status pairs, in the following format: + <enable_reg 0x4 status_reg 0x4>... +- interrupt-controller: identifies the node as an interrupt controller +- #interrupt-cells: specifies the number of cells needed to encode an interrupt + source, should be 1. +- interrupt-parent: specifies the phandle to the parent interrupt controller + this one is cascaded from +- interrupts: specifies the interrupt line in the interrupt-parent controller + node, valid values depend on the type of parent interrupt controller + +Optional properties: + +- brcm,irq-can-wake: if present, this means the L2 controller can be used as a + wakeup source for system suspend/resume. + +Example: + +irq0_intc: interrupt-controller@10000020 { + compatible = "brcm,bcm3380-l2-intc"; + reg = <0x10000024 0x4 0x1000002c 0x4>, + <0x10000020 0x4 0x10000028 0x4>; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&cpu_intc>; + interrupts = <2>; +}; diff --git a/dts/Bindings/interrupt-controller/brcm,bcm7038-l1-intc.txt b/dts/Bindings/interrupt-controller/brcm,bcm7038-l1-intc.txt new file mode 100644 index 0000000000..cc217b22dc --- /dev/null +++ b/dts/Bindings/interrupt-controller/brcm,bcm7038-l1-intc.txt @@ -0,0 +1,52 @@ +Broadcom BCM7038-style Level 1 interrupt controller + +This block is a first level interrupt controller that is typically connected +directly to one of the HW INT lines on each CPU. Every BCM7xxx set-top chip +since BCM7038 has contained this hardware. + +Key elements of the hardware design include: + +- 64, 96, 128, or 160 incoming level IRQ lines + +- Most onchip peripherals are wired directly to an L1 input + +- A separate instance of the register set for each CPU, allowing individual + peripheral IRQs to be routed to any CPU + +- Atomic mask/unmask operations + +- No polarity/level/edge settings + +- No FIFO or priority encoder logic; software is expected to read all + 2-5 status words to determine which IRQs are pending + +Required properties: + +- compatible: should be "brcm,bcm7038-l1-intc" +- reg: specifies the base physical address and size of the registers; + the number of supported IRQs is inferred from the size argument +- interrupt-controller: identifies the node as an interrupt controller +- #interrupt-cells: specifies the number of cells needed to encode an interrupt + source, should be 1. +- interrupt-parent: specifies the phandle to the parent interrupt controller(s) + this one is cascaded from +- interrupts: specifies the interrupt line(s) in the interrupt-parent controller + node; valid values depend on the type of parent interrupt controller + +If multiple reg ranges and interrupt-parent entries are present on an SMP +system, the driver will allow IRQ SMP affinity to be set up through the +/proc/irq/ interface. In the simplest possible configuration, only one +reg range and one interrupt-parent is needed. + +Example: + +periph_intc: periph_intc@1041a400 { + compatible = "brcm,bcm7038-l1-intc"; + reg = <0x1041a400 0x30 0x1041a600 0x30>; + + interrupt-controller; + #interrupt-cells = <1>; + + interrupt-parent = <&cpu_intc>; + interrupts = <2>, <3>; +}; diff --git a/dts/Bindings/interrupt-controller/brcm,bcm7120-l2-intc.txt b/dts/Bindings/interrupt-controller/brcm,bcm7120-l2-intc.txt index bae1f21872..44a9bb15dd 100644 --- a/dts/Bindings/interrupt-controller/brcm,bcm7120-l2-intc.txt +++ b/dts/Bindings/interrupt-controller/brcm,bcm7120-l2-intc.txt @@ -13,8 +13,7 @@ Such an interrupt controller has the following hardware design: or if they will output an interrupt signal at this 2nd level interrupt controller, in particular for UARTs -- typically has one 32-bit enable word and one 32-bit status word, but on - some hardware may have more than one enable/status pair +- has one 32-bit enable word and one 32-bit status word - no atomic set/clear operations @@ -53,9 +52,7 @@ The typical hardware layout for this controller is represented below: Required properties: - compatible: should be "brcm,bcm7120-l2-intc" -- reg: specifies the base physical address and size of the registers; - multiple pairs may be specified, with the first pair handling IRQ offsets - 0..31 and the second pair handling 32..63 +- reg: specifies the base physical address and size of the registers - interrupt-controller: identifies the node as an interrupt controller - #interrupt-cells: specifies the number of cells needed to encode an interrupt source, should be 1. @@ -66,10 +63,7 @@ Required properties: - brcm,int-map-mask: 32-bits bit mask describing how many and which interrupts are wired to this 2nd level interrupt controller, and how they match their respective interrupt parents. Should match exactly the number of interrupts - specified in the 'interrupts' property, multiplied by the number of - enable/status register pairs implemented by this controller. For - multiple parent IRQs with multiple enable/status words, this looks like: - <irq0_w0 irq0_w1 irq1_w0 irq1_w1 ...> + specified in the 'interrupts' property. Optional properties: diff --git a/dts/Bindings/interrupt-controller/cdns,xtensa-mx.txt b/dts/Bindings/interrupt-controller/cdns,xtensa-mx.txt new file mode 100644 index 0000000000..d4de980e55 --- /dev/null +++ b/dts/Bindings/interrupt-controller/cdns,xtensa-mx.txt @@ -0,0 +1,18 @@ +* Xtensa Interrupt Distributor and Programmable Interrupt Controller (MX) + +Required properties: +- compatible: Should be "cdns,xtensa-mx". + +Remaining properties have exact same meaning as in Xtensa PIC +(see cdns,xtensa-pic.txt). + +Examples: + pic: pic { + compatible = "cdns,xtensa-mx"; + /* one cell: internal irq number, + * two cells: second cell == 0: internal irq number + * second cell == 1: external irq number + */ + #interrupt-cells = <2>; + interrupt-controller; + }; diff --git a/dts/Bindings/interrupt-controller/cdns,xtensa-pic.txt b/dts/Bindings/interrupt-controller/cdns,xtensa-pic.txt new file mode 100644 index 0000000000..026ef4cfc1 --- /dev/null +++ b/dts/Bindings/interrupt-controller/cdns,xtensa-pic.txt @@ -0,0 +1,25 @@ +* Xtensa built-in Programmable Interrupt Controller (PIC) + +Required properties: +- compatible: Should be "cdns,xtensa-pic". +- interrupt-controller: Identifies the node as an interrupt controller. +- #interrupt-cells: The number of cells to define the interrupts. + It may be either 1 or 2. + When it's 1, the first cell is the internal IRQ number. + When it's 2, the first cell is the IRQ number, and the second cell + specifies whether it's internal (0) or external (1). + Periferals are usually connected to a fixed external IRQ, but for different + core variants it may be mapped to different internal IRQ. + IRQ sensitivity and priority are fixed for each core variant and may not be + changed at runtime. + +Examples: + pic: pic { + compatible = "cdns,xtensa-pic"; + /* one cell: internal irq number, + * two cells: second cell == 0: internal irq number + * second cell == 1: external irq number + */ + #interrupt-cells = <2>; + interrupt-controller; + }; diff --git a/dts/Bindings/interrupt-controller/mips-gic.txt b/dts/Bindings/interrupt-controller/mips-gic.txt index 5a65478e5d..aae4c384ee 100644 --- a/dts/Bindings/interrupt-controller/mips-gic.txt +++ b/dts/Bindings/interrupt-controller/mips-gic.txt @@ -27,8 +27,13 @@ Optional properties: Required properties for timer sub-node: - compatible : Should be "mti,gic-timer". - interrupts : Interrupt for the GIC local timer. + +Optional properties for timer sub-node: +- clocks : GIC timer operating clock. - clock-frequency : Clock frequency at which the GIC timers operate. +Note that one of clocks or clock-frequency must be specified. + Example: gic: interrupt-controller@1bdc0000 { diff --git a/dts/Bindings/interrupt-controller/nvidia,tegra-ictlr.txt b/dts/Bindings/interrupt-controller/nvidia,tegra-ictlr.txt new file mode 100644 index 0000000000..1099fe0788 --- /dev/null +++ b/dts/Bindings/interrupt-controller/nvidia,tegra-ictlr.txt @@ -0,0 +1,43 @@ +NVIDIA Legacy Interrupt Controller + +All Tegra SoCs contain a legacy interrupt controller that routes +interrupts to the GIC, and also serves as a wakeup source. It is also +referred to as "ictlr", hence the name of the binding. + +The HW block exposes a number of interrupt controllers, each +implementing a set of 32 interrupts. + +Required properties: + +- compatible : should be: "nvidia,tegra<chip>-ictlr". The LIC on + subsequent SoCs remained backwards-compatible with Tegra30, so on + Tegra generations later than Tegra30 the compatible value should + include "nvidia,tegra30-ictlr". +- reg : Specifies base physical address and size of the registers. + Each controller must be described separately (Tegra20 has 4 of them, + whereas Tegra30 and later have 5" +- interrupt-controller : Identifies the node as an interrupt controller. +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The value must be 3. +- interrupt-parent : a phandle to the GIC these interrupts are routed + to. + +Notes: + +- Because this HW ultimately routes interrupts to the GIC, the + interrupt specifier must be that of the GIC. +- Only SPIs can use the ictlr as an interrupt parent. SGIs and PPIs + are explicitly forbidden. + +Example: + + ictlr: interrupt-controller@60004000 { + compatible = "nvidia,tegra20-ictlr", "nvidia,tegra-ictlr"; + reg = <0x60004000 64>, + <0x60004100 64>, + <0x60004200 64>, + <0x60004300 64>; + interrupt-controller; + #interrupt-cells = <3>; + interrupt-parent = <&intc>; + }; diff --git a/dts/Bindings/interrupt-controller/renesas,irqc.txt b/dts/Bindings/interrupt-controller/renesas,irqc.txt index 1a88e62228..63633bdea7 100644 --- a/dts/Bindings/interrupt-controller/renesas,irqc.txt +++ b/dts/Bindings/interrupt-controller/renesas,irqc.txt @@ -4,7 +4,7 @@ Required properties: - compatible: has to be "renesas,irqc-<soctype>", "renesas,irqc" as fallback. Examples with soctypes are: - - "renesas,irqc-r8a73a4" (R-Mobile AP6) + - "renesas,irqc-r8a73a4" (R-Mobile APE6) - "renesas,irqc-r8a7790" (R-Car H2) - "renesas,irqc-r8a7791" (R-Car M2-W) - "renesas,irqc-r8a7792" (R-Car V2H) @@ -12,6 +12,7 @@ Required properties: - "renesas,irqc-r8a7794" (R-Car E2) - #interrupt-cells: has to be <2>: an interrupt index and flags, as defined in interrupts.txt in this directory +- clocks: Must contain a reference to the functional clock. Optional properties: @@ -29,4 +30,5 @@ Example: <0 1 IRQ_TYPE_LEVEL_HIGH>, <0 2 IRQ_TYPE_LEVEL_HIGH>, <0 3 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp4_clks R8A7790_CLK_IRQC>; }; diff --git a/dts/Bindings/interrupt-controller/st,sti-irq-syscfg.txt b/dts/Bindings/interrupt-controller/st,sti-irq-syscfg.txt new file mode 100644 index 0000000000..ced6014061 --- /dev/null +++ b/dts/Bindings/interrupt-controller/st,sti-irq-syscfg.txt @@ -0,0 +1,35 @@ +STMicroelectronics STi System Configuration Controlled IRQs +----------------------------------------------------------- + +On STi based systems; External, CTI (Core Sight), PMU (Performance Management), +and PL310 L2 Cache IRQs are controlled using System Configuration registers. +This driver is used to unmask them prior to use. + +Required properties: +- compatible : Should be set to one of: + "st,stih415-irq-syscfg" + "st,stih416-irq-syscfg" + "st,stih407-irq-syscfg" + "st,stid127-irq-syscfg" +- st,syscfg : Phandle to Cortex-A9 IRQ system config registers +- st,irq-device : Array of IRQs to enable - should be 2 in length +- st,fiq-device : Array of FIQs to enable - should be 2 in length + +Optional properties: +- st,invert-ext : External IRQs can be inverted at will. This property inverts + these IRQs using bitwise logic. A number of defines have been + provided for convenience: + ST_IRQ_SYSCFG_EXT_1_INV + ST_IRQ_SYSCFG_EXT_2_INV + ST_IRQ_SYSCFG_EXT_3_INV +Example: + +irq-syscfg { + compatible = "st,stih416-irq-syscfg"; + st,syscfg = <&syscfg_cpu>; + st,irq-device = <ST_IRQ_SYSCFG_PMU_0>, + <ST_IRQ_SYSCFG_PMU_1>; + st,fiq-device = <ST_IRQ_SYSCFG_DISABLED>, + <ST_IRQ_SYSCFG_DISABLED>; + st,invert-ext = <(ST_IRQ_SYSCFG_EXT_1_INV | ST_IRQ_SYSCFG_EXT_3_INV)>; +}; diff --git a/dts/Bindings/interrupt-controller/ti,omap4-wugen-mpu b/dts/Bindings/interrupt-controller/ti,omap4-wugen-mpu new file mode 100644 index 0000000000..43effa0a4f --- /dev/null +++ b/dts/Bindings/interrupt-controller/ti,omap4-wugen-mpu @@ -0,0 +1,33 @@ +TI OMAP4 Wake-up Generator + +All TI OMAP4/5 (and their derivatives) an interrupt controller that +routes interrupts to the GIC, and also serves as a wakeup source. It +is also referred to as "WUGEN-MPU", hence the name of the binding. + +Reguired properties: + +- compatible : should contain at least "ti,omap4-wugen-mpu" or + "ti,omap5-wugen-mpu" +- reg : Specifies base physical address and size of the registers. +- interrupt-controller : Identifies the node as an interrupt controller. +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The value must be 3. +- interrupt-parent : a phandle to the GIC these interrupts are routed + to. + +Notes: + +- Because this HW ultimately routes interrupts to the GIC, the + interrupt specifier must be that of the GIC. +- Only SPIs can use the WUGEN as an interrupt parent. SGIs and PPIs + are explicitly forbiden. + +Example: + + wakeupgen: interrupt-controller@48281000 { + compatible = "ti,omap5-wugen-mpu", "ti,omap4-wugen-mpu"; + interrupt-controller; + #interrupt-cells = <3>; + reg = <0x48281000 0x1000>; + interrupt-parent = <&gic>; + }; diff --git a/dts/Bindings/leds/common.txt b/dts/Bindings/leds/common.txt index 34811c57db..747c53805e 100644 --- a/dts/Bindings/leds/common.txt +++ b/dts/Bindings/leds/common.txt @@ -14,8 +14,10 @@ Optional properties for child nodes: - led-sources : List of device current outputs the LED is connected to. The outputs are identified by the numbers that must be defined in the LED device binding documentation. -- label : The label for this LED. If omitted, the label is - taken from the node name (excluding the unit address). +- label : The label for this LED. If omitted, the label is taken from the node + name (excluding the unit address). It has to uniquely identify + a device, i.e. no other LED class device can be assigned the same + label. - linux,default-trigger : This parameter, if present, is a string defining the trigger assigned to the LED. Current triggers are: diff --git a/dts/Bindings/leds/leds-gpio.txt b/dts/Bindings/leds/leds-gpio.txt index f77148f372..fea1ebfe24 100644 --- a/dts/Bindings/leds/leds-gpio.txt +++ b/dts/Bindings/leds/leds-gpio.txt @@ -26,16 +26,18 @@ LED sub-node properties: Examples: +#include <dt-bindings/gpio/gpio.h> + leds { compatible = "gpio-leds"; hdd { label = "IDE Activity"; - gpios = <&mcu_pio 0 1>; /* Active low */ + gpios = <&mcu_pio 0 GPIO_ACTIVE_LOW>; linux,default-trigger = "ide-disk"; }; fault { - gpios = <&mcu_pio 1 0>; + gpios = <&mcu_pio 1 GPIO_ACTIVE_HIGH>; /* Keep LED on if BIOS detected hardware fault */ default-state = "keep"; }; @@ -44,11 +46,11 @@ leds { run-control { compatible = "gpio-leds"; red { - gpios = <&mpc8572 6 0>; + gpios = <&mpc8572 6 GPIO_ACTIVE_HIGH>; default-state = "off"; }; green { - gpios = <&mpc8572 7 0>; + gpios = <&mpc8572 7 GPIO_ACTIVE_HIGH>; default-state = "on"; }; }; @@ -57,7 +59,7 @@ leds { compatible = "gpio-leds"; charger-led { - gpios = <&gpio1 2 0>; + gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>; linux,default-trigger = "max8903-charger-charging"; retain-state-suspended; }; diff --git a/dts/Bindings/leds/leds-pm8941-wled.txt b/dts/Bindings/leds/leds-pm8941-wled.txt new file mode 100644 index 0000000000..a85a964d61 --- /dev/null +++ b/dts/Bindings/leds/leds-pm8941-wled.txt @@ -0,0 +1,43 @@ +Binding for Qualcomm PM8941 WLED driver + +Required properties: +- compatible: should be "qcom,pm8941-wled" +- reg: slave address + +Optional properties: +- label: The label for this led + See Documentation/devicetree/bindings/leds/common.txt +- linux,default-trigger: Default trigger assigned to the LED + See Documentation/devicetree/bindings/leds/common.txt +- qcom,cs-out: bool; enable current sink output +- qcom,cabc: bool; enable content adaptive backlight control +- qcom,ext-gen: bool; use externally generated modulator signal to dim +- qcom,current-limit: mA; per-string current limit; value from 0 to 25 + default: 20mA +- qcom,current-boost-limit: mA; boost current limit; one of: + 105, 385, 525, 805, 980, 1260, 1400, 1680 + default: 805mA +- qcom,switching-freq: kHz; switching frequency; one of: + 600, 640, 685, 738, 800, 872, 960, 1066, 1200, 1371, + 1600, 1920, 2400, 3200, 4800, 9600, + default: 1600kHz +- qcom,ovp: V; Over-voltage protection limit; one of: + 27, 29, 32, 35 + default: 29V +- qcom,num-strings: #; number of led strings attached; value from 1 to 3 + default: 2 + +Example: + +pm8941-wled@d800 { + compatible = "qcom,pm8941-wled"; + reg = <0xd800>; + label = "backlight"; + + qcom,cs-out; + qcom,current-limit = <20>; + qcom,current-boost-limit = <805>; + qcom,switching-freq = <1600>; + qcom,ovp = <29>; + qcom,num-strings = <2>; +}; diff --git a/dts/Bindings/mailbox/arm-mhu.txt b/dts/Bindings/mailbox/arm-mhu.txt new file mode 100644 index 0000000000..4971f03f0b --- /dev/null +++ b/dts/Bindings/mailbox/arm-mhu.txt @@ -0,0 +1,43 @@ +ARM MHU Mailbox Driver +====================== + +The ARM's Message-Handling-Unit (MHU) is a mailbox controller that has +3 independent channels/links to communicate with remote processor(s). + MHU links are hardwired on a platform. A link raises interrupt for any +received data. However, there is no specified way of knowing if the sent +data has been read by the remote. This driver assumes the sender polls +STAT register and the remote clears it after having read the data. +The last channel is specified to be a 'Secure' resource, hence can't be +used by Linux running NS. + +Mailbox Device Node: +==================== + +Required properties: +-------------------- +- compatible: Shall be "arm,mhu" & "arm,primecell" +- reg: Contains the mailbox register address range (base + address and length) +- #mbox-cells Shall be 1 - the index of the channel needed. +- interrupts: Contains the interrupt information corresponding to + each of the 3 links of MHU. + +Example: +-------- + + mhu: mailbox@2b1f0000 { + #mbox-cells = <1>; + compatible = "arm,mhu", "arm,primecell"; + reg = <0 0x2b1f0000 0x1000>; + interrupts = <0 36 4>, /* LP-NonSecure */ + <0 35 4>, /* HP-NonSecure */ + <0 37 4>; /* Secure */ + clocks = <&clock 0 2 1>; + clock-names = "apb_pclk"; + }; + + mhu_client: scb@2e000000 { + compatible = "fujitsu,mb86s70-scb-1.0"; + reg = <0 0x2e000000 0x4000>; + mboxes = <&mhu 1>; /* HP-NonSecure */ + }; diff --git a/dts/Bindings/media/exynos-jpeg-codec.txt b/dts/Bindings/media/exynos-jpeg-codec.txt index bf52ed4a50..4ef45636eb 100644 --- a/dts/Bindings/media/exynos-jpeg-codec.txt +++ b/dts/Bindings/media/exynos-jpeg-codec.txt @@ -4,7 +4,7 @@ Required properties: - compatible : should be one of: "samsung,s5pv210-jpeg", "samsung,exynos4210-jpeg", - "samsung,exynos3250-jpeg"; + "samsung,exynos3250-jpeg", "samsung,exynos5420-jpeg"; - reg : address and length of the JPEG codec IP register set; - interrupts : specifies the JPEG codec IP interrupt; - clock-names : should contain: diff --git a/dts/Bindings/media/i2c/mt9v032.txt b/dts/Bindings/media/i2c/mt9v032.txt new file mode 100644 index 0000000000..202565313e --- /dev/null +++ b/dts/Bindings/media/i2c/mt9v032.txt @@ -0,0 +1,39 @@ +* Aptina 1/3-Inch WVGA CMOS Digital Image Sensor + +The Aptina MT9V032 is a 1/3-inch CMOS active pixel digital image sensor with +an active array size of 752H x 480V. It is programmable through a simple +two-wire serial interface. + +Required Properties: + +- compatible: value should be either one among the following + (a) "aptina,mt9v022" for MT9V022 color sensor + (b) "aptina,mt9v022m" for MT9V022 monochrome sensor + (c) "aptina,mt9v024" for MT9V024 color sensor + (d) "aptina,mt9v024m" for MT9V024 monochrome sensor + (e) "aptina,mt9v032" for MT9V032 color sensor + (f) "aptina,mt9v032m" for MT9V032 monochrome sensor + (g) "aptina,mt9v034" for MT9V034 color sensor + (h) "aptina,mt9v034m" for MT9V034 monochrome sensor + +Optional Properties: + +- link-frequencies: List of allowed link frequencies in Hz. Each frequency is + expressed as a 64-bit big-endian integer. + +For further reading on port node refer to +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + mt9v032@5c { + compatible = "aptina,mt9v032"; + reg = <0x5c>; + + port { + mt9v032_out: endpoint { + link-frequencies = /bits/ 64 + <13000000 26600000 27000000>; + }; + }; + }; diff --git a/dts/Bindings/media/i2c/ov2640.txt b/dts/Bindings/media/i2c/ov2640.txt new file mode 100644 index 0000000000..c429b5bdca --- /dev/null +++ b/dts/Bindings/media/i2c/ov2640.txt @@ -0,0 +1,46 @@ +* Omnivision OV2640 CMOS sensor + +The Omnivision OV2640 sensor support multiple resolutions output, such as +CIF, SVGA, UXGA. It also can support YUV422/420, RGB565/555 or raw RGB +output format. + +Required Properties: +- compatible: should be "ovti,ov2640" +- clocks: reference to the xvclk input clock. +- clock-names: should be "xvclk". + +Optional Properties: +- resetb-gpios: reference to the GPIO connected to the resetb pin, if any. +- pwdn-gpios: reference to the GPIO connected to the pwdn pin, if any. + +The device node must contain one 'port' child node for its digital output +video port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + i2c1: i2c@f0018000 { + ov2640: camera@0x30 { + compatible = "ovti,ov2640"; + reg = <0x30>; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pck1 &pinctrl_ov2640_pwdn &pinctrl_ov2640_resetb>; + + resetb-gpios = <&pioE 24 GPIO_ACTIVE_LOW>; + pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>; + + clocks = <&pck1>; + clock-names = "xvclk"; + + assigned-clocks = <&pck1>; + assigned-clock-rates = <25000000>; + + port { + ov2640_0: endpoint { + remote-endpoint = <&isi_0>; + bus-width = <8>; + }; + }; + }; + }; diff --git a/dts/Bindings/media/i2c/ov2659.txt b/dts/Bindings/media/i2c/ov2659.txt new file mode 100644 index 0000000000..cabc7d827d --- /dev/null +++ b/dts/Bindings/media/i2c/ov2659.txt @@ -0,0 +1,38 @@ +* OV2659 1/5-Inch 2Mp SOC Camera + +The Omnivision OV2659 is a 1/5-inch SOC camera, with an active array size of +1632H x 1212V. It is programmable through a SCCB. The OV2659 sensor supports +multiple resolutions output, such as UXGA, SVGA, 720p. It also can support +YUV422, RGB565/555 or raw RGB output formats. + +Required Properties: +- compatible: Must be "ovti,ov2659" +- reg: I2C slave address +- clocks: reference to the xvclk input clock. +- clock-names: should be "xvclk". +- link-frequencies: target pixel clock frequency. + +For further reading on port node refer to +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + i2c0@1c22000 { + ... + ... + ov2659@30 { + compatible = "ovti,ov2659"; + reg = <0x30>; + + clocks = <&clk_ov2659 0>; + clock-names = "xvclk"; + + port { + ov2659_0: endpoint { + remote-endpoint = <&vpfe_ep>; + link-frequencies = /bits/ 64 <70000000>; + }; + }; + }; + ... + }; diff --git a/dts/Bindings/media/ti,omap3isp.txt b/dts/Bindings/media/ti,omap3isp.txt new file mode 100644 index 0000000000..ac23de8556 --- /dev/null +++ b/dts/Bindings/media/ti,omap3isp.txt @@ -0,0 +1,71 @@ +OMAP 3 ISP Device Tree bindings +=============================== + +The DT definitions can be found in include/dt-bindings/media/omap3-isp.h. + +Required properties +=================== + +compatible : must contain "ti,omap3-isp" + +reg : the two registers sets (physical address and length) for the + ISP. The first set contains the core ISP registers up to + the end of the SBL block. The second set contains the + CSI PHYs and receivers registers. +interrupts : the ISP interrupt specifier +iommus : phandle and IOMMU specifier for the IOMMU that serves the ISP +syscon : the phandle and register offset to the Complex I/O or CSI-PHY + register +ti,phy-type : 0 -- OMAP3ISP_PHY_TYPE_COMPLEX_IO (e.g. 3430) + 1 -- OMAP3ISP_PHY_TYPE_CSIPHY (e.g. 3630) +#clock-cells : Must be 1 --- the ISP provides two external clocks, + cam_xclka and cam_xclkb, at indices 0 and 1, + respectively. Please find more information on common + clock bindings in ../clock/clock-bindings.txt. + +Port nodes (optional) +--------------------- + +More documentation on these bindings is available in +video-interfaces.txt in the same directory. + +reg : The interface: + 0 - parallel (CCDC) + 1 - CSIPHY1 -- CSI2C / CCP2B on 3630; + CSI1 -- CSIb on 3430 + 2 - CSIPHY2 -- CSI2A / CCP2B on 3630; + CSI2 -- CSIa on 3430 + +Optional properties +=================== + +vdd-csiphy1-supply : voltage supply of the CSI-2 PHY 1 +vdd-csiphy2-supply : voltage supply of the CSI-2 PHY 2 + +Endpoint nodes +-------------- + +lane-polarities : lane polarity (required on CSI-2) + 0 -- not inverted; 1 -- inverted +data-lanes : an array of data lanes from 1 to 3. The length can + be either 1 or 2. (required on CSI-2) +clock-lanes : the clock lane (from 1 to 3). (required on CSI-2) + + +Example +======= + + isp@480bc000 { + compatible = "ti,omap3-isp"; + reg = <0x480bc000 0x12fc + 0x480bd800 0x0600>; + interrupts = <24>; + iommus = <&mmu_isp>; + syscon = <&scm_conf 0x2f0>; + ti,phy-type = <OMAP3ISP_PHY_TYPE_CSIPHY>; + #clock-cells = <1>; + ports { + #address-cells = <1>; + #size-cells = <0>; + }; + }; diff --git a/dts/Bindings/media/video-interfaces.txt b/dts/Bindings/media/video-interfaces.txt index 571b4c6066..9cd2a36912 100644 --- a/dts/Bindings/media/video-interfaces.txt +++ b/dts/Bindings/media/video-interfaces.txt @@ -106,6 +106,12 @@ Optional endpoint properties - link-frequencies: Allowed data bus frequencies. For MIPI CSI-2, for instance, this is the actual frequency of the bus, not bits per clock per lane value. An array of 64-bit unsigned integers. +- lane-polarities: an array of polarities of the lanes starting from the clock + lane and followed by the data lanes in the same order as in data-lanes. + Valid values are 0 (normal) and 1 (inverted). The length of the array + should be the combined length of data-lanes and clock-lanes properties. + If the lane-polarities property is omitted, the value must be interpreted + as 0 (normal). This property is valid for serial busses only. Example diff --git a/dts/Bindings/media/xilinx/video.txt b/dts/Bindings/media/xilinx/video.txt new file mode 100644 index 0000000000..cbd46fa098 --- /dev/null +++ b/dts/Bindings/media/xilinx/video.txt @@ -0,0 +1,35 @@ +DT bindings for Xilinx video IP cores +------------------------------------- + +Xilinx video IP cores process video streams by acting as video sinks and/or +sources. They are connected by links through their input and output ports, +creating a video pipeline. + +Each video IP core is represented by an AMBA bus child node in the device +tree using bindings documented in this directory. Connections between the IP +cores are represented as defined in ../video-interfaces.txt. + +The whole pipeline is represented by an AMBA bus child node in the device +tree using bindings documented in ./xlnx,video.txt. + +Common properties +----------------- + +The following properties are common to all Xilinx video IP cores. + +- xlnx,video-format: This property represents a video format transmitted on an + AXI bus between video IP cores, using its VF code as defined in "AXI4-Stream + Video IP and System Design Guide" [UG934]. How the format relates to the IP + core is decribed in the IP core bindings documentation. + +- xlnx,video-width: This property qualifies the video format with the sample + width expressed as a number of bits per pixel component. All components must + use the same width. + +- xlnx,cfa-pattern: When the video format is set to Mono/Sensor, this property + describes the sensor's color filter array pattern. Supported values are + "bggr", "gbrg", "grbg", "rggb" and "mono". If not specified, the pattern + defaults to "mono". + + +[UG934] http://www.xilinx.com/support/documentation/ip_documentation/axi_videoip/v1_0/ug934_axi_videoIP.pdf diff --git a/dts/Bindings/media/xilinx/xlnx,v-tc.txt b/dts/Bindings/media/xilinx/xlnx,v-tc.txt new file mode 100644 index 0000000000..2aed3b4a6c --- /dev/null +++ b/dts/Bindings/media/xilinx/xlnx,v-tc.txt @@ -0,0 +1,33 @@ +Xilinx Video Timing Controller (VTC) +------------------------------------ + +The Video Timing Controller is a general purpose video timing generator and +detector. + +Required properties: + + - compatible: Must be "xlnx,v-tc-6.1". + + - reg: Physical base address and length of the registers set for the device. + + - clocks: Must contain a clock specifier for the VTC core and timing + interfaces clock. + +Optional properties: + + - xlnx,detector: The VTC has a timing detector + - xlnx,generator: The VTC has a timing generator + + At least one of the xlnx,detector and xlnx,generator properties must be + specified. + + +Example: + + vtc: vtc@43c40000 { + compatible = "xlnx,v-tc-6.1"; + reg = <0x43c40000 0x10000>; + + clocks = <&clkc 15>; + xlnx,generator; + }; diff --git a/dts/Bindings/media/xilinx/xlnx,v-tpg.txt b/dts/Bindings/media/xilinx/xlnx,v-tpg.txt new file mode 100644 index 0000000000..9dd86b3db9 --- /dev/null +++ b/dts/Bindings/media/xilinx/xlnx,v-tpg.txt @@ -0,0 +1,71 @@ +Xilinx Video Test Pattern Generator (TPG) +----------------------------------------- + +Required properties: + +- compatible: Must contain at least one of + + "xlnx,v-tpg-5.0" (TPG version 5.0) + "xlnx,v-tpg-6.0" (TPG version 6.0) + + TPG versions backward-compatible with previous versions should list all + compatible versions in the newer to older order. + +- reg: Physical base address and length of the registers set for the device. + +- clocks: Reference to the video core clock. + +- xlnx,video-format, xlnx,video-width: Video format and width, as defined in + video.txt. + +- port: Video port, using the DT bindings defined in ../video-interfaces.txt. + The TPG has a single output port numbered 0. + +Optional properties: + +- xlnx,vtc: A phandle referencing the Video Timing Controller that generates + video timings for the TPG test patterns. + +- timing-gpios: Specifier for a GPIO that controls the timing mux at the TPG + input. The GPIO active level corresponds to the selection of VTC-generated + video timings. + +The xlnx,vtc and timing-gpios properties are mandatory when the TPG is +synthesized with two ports and forbidden when synthesized with one port. + +Example: + + tpg_0: tpg@40050000 { + compatible = "xlnx,v-tpg-6.0", "xlnx,v-tpg-5.0"; + reg = <0x40050000 0x10000>; + clocks = <&clkc 15>; + + xlnx,vtc = <&vtc_3>; + timing-gpios = <&ps7_gpio_0 55 GPIO_ACTIVE_LOW>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + xlnx,video-format = <XVIP_VF_YUV_422>; + xlnx,video-width = <8>; + + tpg_in: endpoint { + remote-endpoint = <&adv7611_out>; + }; + }; + port@1 { + reg = <1>; + + xlnx,video-format = <XVIP_VF_YUV_422>; + xlnx,video-width = <8>; + + tpg1_out: endpoint { + remote-endpoint = <&switch_in0>; + }; + }: + }; + }; diff --git a/dts/Bindings/media/xilinx/xlnx,video.txt b/dts/Bindings/media/xilinx/xlnx,video.txt new file mode 100644 index 0000000000..5a02270236 --- /dev/null +++ b/dts/Bindings/media/xilinx/xlnx,video.txt @@ -0,0 +1,55 @@ +Xilinx Video IP Pipeline (VIPP) +------------------------------- + +General concept +--------------- + +Xilinx video IP pipeline processes video streams through one or more Xilinx +video IP cores. Each video IP core is represented as documented in video.txt +and IP core specific documentation, xlnx,v-*.txt, in this directory. The DT +node of the VIPP represents as a top level node of the pipeline and defines +mappings between DMAs and the video IP cores. + +Required properties: + +- compatible: Must be "xlnx,video". + +- dmas, dma-names: List of one DMA specifier and identifier string (as defined + in Documentation/devicetree/bindings/dma/dma.txt) per port. Each port + requires a DMA channel with the identifier string set to "port" followed by + the port index. + +- ports: Video port, using the DT bindings defined in ../video-interfaces.txt. + +Required port properties: + +- direction: should be either "input" or "output" depending on the direction + of stream. + +Example: + + video_cap { + compatible = "xlnx,video"; + dmas = <&vdma_1 1>, <&vdma_3 1>; + dma-names = "port0", "port1"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + direction = "input"; + vcap0_in0: endpoint { + remote-endpoint = <&scaler0_out>; + }; + }; + port@1 { + reg = <1>; + direction = "input"; + vcap0_in1: endpoint { + remote-endpoint = <&switch_out1>; + }; + }; + }; + }; diff --git a/dts/Bindings/memory-controllers/ingenic,jz4780-nemc.txt b/dts/Bindings/memory-controllers/ingenic,jz4780-nemc.txt new file mode 100644 index 0000000000..f936b5589b --- /dev/null +++ b/dts/Bindings/memory-controllers/ingenic,jz4780-nemc.txt @@ -0,0 +1,75 @@ +* Ingenic JZ4780 NAND/external memory controller (NEMC) + +This file documents the device tree bindings for the NEMC external memory +controller in Ingenic JZ4780 + +Required properties: +- compatible: Should be set to one of: + "ingenic,jz4780-nemc" (JZ4780) +- reg: Should specify the NEMC controller registers location and length. +- clocks: Clock for the NEMC controller. +- #address-cells: Must be set to 2. +- #size-cells: Must be set to 1. +- ranges: A set of ranges for each bank describing the physical memory layout. + Each should specify the following 4 integer values: + + <cs number> 0 <physical address of mapping> <size of mapping> + +Each child of the NEMC node describes a device connected to the NEMC. + +Required child node properties: +- reg: Should contain at least one register specifier, given in the following + format: + + <cs number> <offset> <size> + + Multiple registers can be specified across multiple banks. This is needed, + for example, for packaged NAND devices with multiple dies. Such devices + should be grouped into a single node. + +Optional child node properties: +- ingenic,nemc-bus-width: Specifies the bus width in bits. Defaults to 8 bits. +- ingenic,nemc-tAS: Address setup time in nanoseconds. +- ingenic,nemc-tAH: Address hold time in nanoseconds. +- ingenic,nemc-tBP: Burst pitch time in nanoseconds. +- ingenic,nemc-tAW: Access wait time in nanoseconds. +- ingenic,nemc-tSTRV: Static memory recovery time in nanoseconds. + +If a child node references multiple banks in its "reg" property, the same value +for all optional parameters will be configured for all banks. If any optional +parameters are omitted, they will be left unchanged from whatever they are +configured to when the NEMC device is probed (which may be the reset value as +given in the hardware reference manual, or a value configured by the boot +loader). + +Example (NEMC node with a NAND child device attached at CS1): + +nemc: nemc@13410000 { + compatible = "ingenic,jz4780-nemc"; + reg = <0x13410000 0x10000>; + + #address-cells = <2>; + #size-cells = <1>; + + ranges = <1 0 0x1b000000 0x1000000 + 2 0 0x1a000000 0x1000000 + 3 0 0x19000000 0x1000000 + 4 0 0x18000000 0x1000000 + 5 0 0x17000000 0x1000000 + 6 0 0x16000000 0x1000000>; + + clocks = <&cgu JZ4780_CLK_NEMC>; + + nand: nand@1 { + compatible = "ingenic,jz4780-nand"; + reg = <1 0 0x1000000>; + + ingenic,nemc-tAS = <10>; + ingenic,nemc-tAH = <5>; + ingenic,nemc-tBP = <10>; + ingenic,nemc-tAW = <15>; + ingenic,nemc-tSTRV = <100>; + + ... + }; +}; diff --git a/dts/Bindings/mfd/arizona.txt b/dts/Bindings/mfd/arizona.txt index 7bd1273f57..7665aa9597 100644 --- a/dts/Bindings/mfd/arizona.txt +++ b/dts/Bindings/mfd/arizona.txt @@ -8,6 +8,7 @@ Required properties: - compatible : One of the following chip-specific strings: "wlf,wm5102" "wlf,wm5110" + "wlf,wm8280" "wlf,wm8997" - reg : I2C slave address when connected using I2C, chip select number when using SPI. @@ -26,21 +27,27 @@ Required properties: - #gpio-cells : Must be 2. The first cell is the pin number and the second cell is used to specify optional parameters (currently unused). - - AVDD-supply, DBVDD1-supply, DBVDD2-supply, DBVDD3-supply (wm5102, wm5110), - CPVDD-supply, SPKVDDL-supply (wm5102, wm5110), SPKVDDR-supply (wm5102, - wm5110), SPKVDD-supply (wm8997) : Power supplies for the device, as covered - in Documentation/devicetree/bindings/regulator/regulator.txt + - AVDD-supply, DBVDD1-supply, CPVDD-supply : Power supplies for the device, + as covered in Documentation/devicetree/bindings/regulator/regulator.txt + + - DBVDD2-supply, DBVDD3-supply : Additional databus power supplies (wm5102, + wm5110, wm8280) + + - SPKVDDL-supply, SPKVDDR-supply : Speaker driver power supplies (wm5102, + wm5110, wm8280) + + - SPKVDD-supply : Speaker driver power supply (wm8997) Optional properties: - wlf,reset : GPIO specifier for the GPIO controlling /RESET - wlf,ldoena : GPIO specifier for the GPIO controlling LDOENA - - wlf,gpio-defaults : A list of GPIO configuration register values. If - absent, no configuration of these registers is performed. If any - entry has a value that is out of range for a 16 bit register then - the chip default will be used. If present exactly five values must - be specified. + - wlf,gpio-defaults : A list of GPIO configuration register values. Defines + for the appropriate values can found in <dt-bindings/mfd/arizona.txt>. If + absent, no configuration of these registers is performed. If any entry has + a value that is out of range for a 16 bit register then the chip default + will be used. If present exactly five values must be specified. - wlf,inmode : A list of INn_MODE register values, where n is the number of input signals. Valid values are 0 (Differential), 1 (Single-ended) and @@ -49,6 +56,12 @@ Optional properties: input singals. If values less than the number of input signals, elements that has not been specifed are set to 0 by default. + - wlf,dmic-ref : DMIC reference voltage source for each input, can be + selected from either MICVDD or one of the MICBIAS's, defines + (ARIZONA_DMIC_xxxx) are provided in <dt-bindings/mfd/arizona.txt>. If + present, the number of values should be less than or equal to the + number of inputs, unspecified inputs will use the chip default. + - DCVDD-supply, MICVDD-supply : Power supplies, only need to be specified if they are being externally supplied. As covered in Documentation/devicetree/bindings/regulator/regulator.txt @@ -73,10 +86,10 @@ codec: wm5102@1a { #gpio-cells = <2>; wlf,gpio-defaults = < - 0x00000000 /* AIF1TXLRCLK */ - 0xffffffff - 0xffffffff - 0xffffffff - 0xffffffff + ARIZONA_GP_FN_TXLRCLK + ARIZONA_GP_DEFAULT + ARIZONA_GP_DEFAULT + ARIZONA_GP_DEFAULT + ARIZONA_GP_DEFAULT >; }; diff --git a/dts/Bindings/mfd/axp20x.txt b/dts/Bindings/mfd/axp20x.txt new file mode 100644 index 0000000000..98685f291a --- /dev/null +++ b/dts/Bindings/mfd/axp20x.txt @@ -0,0 +1,96 @@ +AXP202/AXP209 device tree bindings + +The axp20x family current members : +axp202 (X-Powers) +axp209 (X-Powers) + +Required properties: +- compatible: "x-powers,axp202" or "x-powers,axp209" +- reg: The I2C slave address for the AXP chip +- interrupt-parent: The parent interrupt controller +- interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin +- interrupt-controller: axp20x has its own internal IRQs +- #interrupt-cells: Should be set to 1 + +Optional properties: +- x-powers,dcdc-freq: defines the work frequency of DC-DC in KHz + (range: 750-1875). Default: 1.5MHz +- <input>-supply: a phandle to the regulator supply node. May be omitted if + inputs are unregulated, such as using the IPSOUT output + from the PMIC. + +- regulators: A node that houses a sub-node for each regulator. Regulators + not used but preferred to be managed by the OS should be + listed as well. + See Documentation/devicetree/bindings/regulator/regulator.txt + for more information on standard regulator bindings. + +Optional properties for DCDC regulators: +- x-powers,dcdc-workmode: 1 for PWM mode, 0 for AUTO (PWM/PFM) mode + Default: Current hardware setting + The DCDC regulators work in a mixed PWM/PFM mode, + using PFM under light loads and switching to PWM + for heavier loads. Forcing PWM mode trades efficiency + under light loads for lower output noise. This + probably makes sense for HiFi audio related + applications that aren't battery constrained. + + +AXP202/AXP209 regulators, type, and corresponding input supply names: + +Regulator Type Supply Name Notes +--------- ---- ----------- ----- +DCDC2 : DC-DC buck : vin2-supply +DCDC3 : DC-DC buck : vin3-supply +LDO1 : LDO : acin-supply : always on +LDO2 : LDO : ldo24in-supply : shared supply +LDO3 : LDO : ldo3in-supply +LDO4 : LDO : ldo24in-supply : shared supply +LDO5 : LDO : ldo5in-supply + +Example: + +axp209: pmic@34 { + compatible = "x-powers,axp209"; + reg = <0x34>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <1>; + + regulators { + x-powers,dcdc-freq = <1500>; + + vdd_cpu: dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1450000>; + regulator-name = "vdd-cpu"; + }; + + vdd_int_dll: dcdc3 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-int-dll"; + }; + + vdd_rtc: ldo1 { + regulator-always-on; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-rtc"; + }; + + avcc: ldo2 { + regulator-always-on; + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3300000>; + regulator-name = "avcc"; + }; + + ldo3 { + /* unused but preferred to be managed by OS */ + }; + }; +}; diff --git a/dts/Bindings/mfd/bcm590xx.txt b/dts/Bindings/mfd/brcm,bcm59056.txt index be51a15e05..be51a15e05 100644 --- a/dts/Bindings/mfd/bcm590xx.txt +++ b/dts/Bindings/mfd/brcm,bcm59056.txt diff --git a/dts/Bindings/mfd/da9150.txt b/dts/Bindings/mfd/da9150.txt new file mode 100644 index 0000000000..d0588eaa0d --- /dev/null +++ b/dts/Bindings/mfd/da9150.txt @@ -0,0 +1,43 @@ +Dialog Semiconductor DA9150 Combined Charger/Fuel-Gauge MFD bindings + +DA9150 consists of a group of sub-devices: + +Device Description +------ ----------- +da9150-gpadc : General Purpose ADC +da9150-charger : Battery Charger + +====== + +Required properties: +- compatible : Should be "dlg,da9150" +- reg: Specifies the I2C slave address +- interrupt-parent: Specifies the phandle of the interrupt controller to which + the IRQs from da9150 are delivered to. +- interrupts: IRQ line info for da9150 chip. +- interrupt-controller: da9150 has internal IRQs (own IRQ domain). + (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt for + further information relating to interrupt properties) + +Sub-devices: +- da9150-gpadc: See Documentation/devicetree/bindings/iio/adc/da9150-gpadc.txt +- da9150-charger: See Documentation/devicetree/bindings/power/da9150-charger.txt + + +Example: + + charger_fg: da9150@58 { + compatible = "dlg,da9150"; + reg = <0x58>; + interrupt-parent = <&gpio6>; + interrupts = <11 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + + gpadc: da9150-gpadc { + ... + }; + + da9150-charger { + ... + }; + }; diff --git a/dts/Bindings/mfd/mt6397.txt b/dts/Bindings/mfd/mt6397.txt new file mode 100644 index 0000000000..15043e6526 --- /dev/null +++ b/dts/Bindings/mfd/mt6397.txt @@ -0,0 +1,70 @@ +MediaTek MT6397 Multifunction Device Driver + +MT6397 is a multifunction device with the following sub modules: +- Regulator +- RTC +- Audio codec +- GPIO +- Clock + +It is interfaced to host controller using SPI interface by a proprietary hardware +called PMIC wrapper or pwrap. MT6397 MFD is a child device of pwrap. +See the following for pwarp node definitions: +Documentation/devicetree/bindings/soc/pwrap.txt + +This document describes the binding for MFD device and its sub module. + +Required properties: +compatible: "mediatek,mt6397" + +Optional subnodes: + +- rtc + Required properties: + - compatible: "mediatek,mt6397-rtc" +- regulators + Required properties: + - compatible: "mediatek,mt6397-regulator" + see Documentation/devicetree/bindings/regulator/mt6397-regulator.txt +- codec + Required properties: + - compatible: "mediatek,mt6397-codec" +- clk + Required properties: + - compatible: "mediatek,mt6397-clk" + +Example: + pwrap: pwrap@1000f000 { + compatible = "mediatek,mt8135-pwrap"; + + ... + + pmic { + compatible = "mediatek,mt6397"; + + codec: mt6397codec { + compatible = "mediatek,mt6397-codec"; + }; + + regulators { + compatible = "mediatek,mt6397-regulator"; + + mt6397_vpca15_reg: buck_vpca15 { + regulator-compatible = "buck_vpca15"; + regulator-name = "vpca15"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1400000>; + regulator-ramp-delay = <12500>; + regulator-always-on; + }; + + mt6397_vgp4_reg: ldo_vgp4 { + regulator-compatible = "ldo_vgp4"; + regulator-name = "vgp4"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + }; + }; + }; diff --git a/dts/Bindings/mfd/qcom,spmi-pmic.txt b/dts/Bindings/mfd/qcom,spmi-pmic.txt index 7182b8857f..6ac06c1b9a 100644 --- a/dts/Bindings/mfd/qcom,spmi-pmic.txt +++ b/dts/Bindings/mfd/qcom,spmi-pmic.txt @@ -15,10 +15,21 @@ each. A function can consume one or more of these fixed-size register regions. Required properties: - compatible: Should contain one of: - "qcom,pm8941" - "qcom,pm8841" - "qcom,pma8084" - or generalized "qcom,spmi-pmic". + "qcom,pm8941", + "qcom,pm8841", + "qcom,pma8084", + "qcom,pm8019", + "qcom,pm8226", + "qcom,pm8110", + "qcom,pma8084", + "qcom,pmi8962", + "qcom,pmd9635", + "qcom,pm8994", + "qcom,pmi8994", + "qcom,pm8916", + "qcom,pm8004", + "qcom,pm8909", + or generalized "qcom,spmi-pmic". - reg: Specifies the SPMI USID slave address for this device. For more information see: Documentation/devicetree/bindings/spmi/spmi.txt diff --git a/dts/Bindings/mfd/qcom,tcsr.txt b/dts/Bindings/mfd/qcom,tcsr.txt new file mode 100644 index 0000000000..e90519d566 --- /dev/null +++ b/dts/Bindings/mfd/qcom,tcsr.txt @@ -0,0 +1,22 @@ +QCOM Top Control and Status Register + +Qualcomm devices have a set of registers that provide various control and status +functions for their peripherals. This node is intended to allow access to these +registers via syscon. + +Required properties: +- compatible: Should contain: + "qcom,tcsr-ipq8064", "syscon" for IPQ8064 + "qcom,tcsr-apq8064", "syscon" for APQ8064 + "qcom,tcsr-msm8660", "syscon" for MSM8660 + "qcom,tcsr-msm8960", "syscon" for MSM8960 + "qcom,tcsr-msm8974", "syscon" for MSM8974 + "qcom,tcsr-apq8084", "syscon" for APQ8084 + "qcom,tcsr-msm8916", "syscon" for MSM8916 +- reg: Address range for TCSR registers + +Example: + tcsr: syscon@1a400000 { + compatible = "qcom,tcsr-msm8960", "syscon"; + reg = <0x1a400000 0x100>; + }; diff --git a/dts/Bindings/mfd/qcom-rpm.txt b/dts/Bindings/mfd/qcom-rpm.txt index 85e3198001..5e97a9593a 100644 --- a/dts/Bindings/mfd/qcom-rpm.txt +++ b/dts/Bindings/mfd/qcom-rpm.txt @@ -12,6 +12,7 @@ frequencies. "qcom,rpm-apq8064" "qcom,rpm-msm8660" "qcom,rpm-msm8960" + "qcom,rpm-ipq8064" - reg: Usage: required @@ -31,16 +32,6 @@ frequencies. Value type: <string-array> Definition: must be the three strings "ack", "err" and "wakeup", in order -- #address-cells: - Usage: required - Value type: <u32> - Definition: must be 1 - -- #size-cells: - Usage: required - Value type: <u32> - Definition: must be 0 - - qcom,ipc: Usage: required Value type: <prop-encoded-array> @@ -52,6 +43,188 @@ frequencies. - u32 representing the ipc bit within the register += SUBNODES + +The RPM exposes resources to its subnodes. The below bindings specify the set +of valid subnodes that can operate on these resources. + +== Regulators + +Regulator nodes are identified by their compatible: + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,rpm-pm8058-regulators" + "qcom,rpm-pm8901-regulators" + "qcom,rpm-pm8921-regulators" + +- vdd_l0_l1_lvs-supply: +- vdd_l2_l11_l12-supply: +- vdd_l3_l4_l5-supply: +- vdd_l6_l7-supply: +- vdd_l8-supply: +- vdd_l9-supply: +- vdd_l10-supply: +- vdd_l13_l16-supply: +- vdd_l14_l15-supply: +- vdd_l17_l18-supply: +- vdd_l19_l20-supply: +- vdd_l21-supply: +- vdd_l22-supply: +- vdd_l23_l24_l25-supply: +- vdd_ncp-supply: +- vdd_s0-supply: +- vdd_s1-supply: +- vdd_s2-supply: +- vdd_s3-supply: +- vdd_s4-supply: + Usage: optional (pm8058 only) + Value type: <phandle> + Definition: reference to regulator supplying the input pin, as + described in the data sheet + +- lvs0_in-supply: +- lvs1_in-supply: +- lvs2_in-supply: +- lvs3_in-supply: +- mvs_in-supply: +- vdd_l0-supply: +- vdd_l1-supply: +- vdd_l2-supply: +- vdd_l3-supply: +- vdd_l4-supply: +- vdd_l5-supply: +- vdd_l6-supply: +- vdd_s0-supply: +- vdd_s1-supply: +- vdd_s2-supply: +- vdd_s3-supply: +- vdd_s4-supply: + Usage: optional (pm8901 only) + Value type: <phandle> + Definition: reference to regulator supplying the input pin, as + described in the data sheet + +- vdd_l1_l2_l12_l18-supply: +- vdd_l3_l15_l17-supply: +- vdd_l4_l14-supply: +- vdd_l5_l8_l16-supply: +- vdd_l6_l7-supply: +- vdd_l9_l11-supply: +- vdd_l10_l22-supply: +- vdd_l21_l23_l29-supply: +- vdd_l24-supply: +- vdd_l25-supply: +- vdd_l26-supply: +- vdd_l27-supply: +- vdd_l28-supply: +- vdd_ncp-supply: +- vdd_s1-supply: +- vdd_s2-supply: +- vdd_s4-supply: +- vdd_s5-supply: +- vdd_s6-supply: +- vdd_s7-supply: +- vdd_s8-supply: +- vin_5vs-supply: +- vin_lvs1_3_6-supply: +- vin_lvs2-supply: +- vin_lvs4_5_7-supply: + Usage: optional (pm8921 only) + Value type: <phandle> + Definition: reference to regulator supplying the input pin, as + described in the data sheet + +The regulator node houses sub-nodes for each regulator within the device. Each +sub-node is identified using the node's name, with valid values listed for each +of the pmics below. + +pm8058: + l0, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, l14, l15, + l16, l17, l18, l19, l20, l21, l22, l23, l24, l25, s0, s1, s2, s3, s4, + lvs0, lvs1, ncp + +pm8901: + l0, l1, l2, l3, l4, l5, l6, s0, s1, s2, s3, s4, lvs0, lvs1, lvs2, lvs3, + mvs + +pm8921: + s1, s2, s3, s4, s7, s8, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, + l12, l14, l15, l16, l17, l18, l21, l22, l23, l24, l25, l26, l27, l28, + l29, lvs1, lvs2, lvs3, lvs4, lvs5, lvs6, lvs7, usb-switch, hdmi-switch, + ncp + +The content of each sub-node is defined by the standard binding for regulators - +see regulator.txt - with additional custom properties described below: + +=== Switch-mode Power Supply regulator custom properties + +- bias-pull-down: + Usage: optional + Value type: <empty> + Definition: enable pull down of the regulator when inactive + +- qcom,switch-mode-frequency: + Usage: required + Value type: <u32> + Definition: Frequency (Hz) of the switch-mode power supply; + must be one of: + 19200000, 9600000, 6400000, 4800000, 3840000, 3200000, + 2740000, 2400000, 2130000, 1920000, 1750000, 1600000, + 1480000, 1370000, 1280000, 1200000 + +- qcom,force-mode: + Usage: optional (default if no other qcom,force-mode is specified) + Value type: <u32> + Defintion: indicates that the regulator should be forced to a + particular mode, valid values are: + QCOM_RPM_FORCE_MODE_NONE - do not force any mode + QCOM_RPM_FORCE_MODE_LPM - force into low power mode + QCOM_RPM_FORCE_MODE_HPM - force into high power mode + QCOM_RPM_FORCE_MODE_AUTO - allow regulator to automatically + select its own mode based on + realtime current draw, only for: + pm8921 smps and ftsmps + +- qcom,power-mode-hysteretic: + Usage: optional + Value type: <empty> + Definition: select that the power supply should operate in hysteretic + mode, instead of the default pwm mode + +=== Low-dropout regulator custom properties + +- bias-pull-down: + Usage: optional + Value type: <empty> + Definition: enable pull down of the regulator when inactive + +- qcom,force-mode: + Usage: optional + Value type: <u32> + Defintion: indicates that the regulator should not be forced to any + particular mode, valid values are: + QCOM_RPM_FORCE_MODE_NONE - do not force any mode + QCOM_RPM_FORCE_MODE_LPM - force into low power mode + QCOM_RPM_FORCE_MODE_HPM - force into high power mode + QCOM_RPM_FORCE_MODE_BYPASS - set regulator to use bypass + mode, i.e. to act as a switch + and not regulate, only for: + pm8921 pldo, nldo and nldo1200 + +=== Negative Charge Pump custom properties + +- qcom,switch-mode-frequency: + Usage: required + Value type: <u32> + Definition: Frequency (Hz) of the swith mode power supply; + must be one of: + 19200000, 9600000, 6400000, 4800000, 3840000, 3200000, + 2740000, 2400000, 2130000, 1920000, 1750000, 1600000, + 1480000, 1370000, 1280000, 1200000 + = EXAMPLE #include <dt-bindings/mfd/qcom-rpm.h> @@ -64,7 +237,28 @@ frequencies. interrupts = <0 19 0>, <0 21 0>, <0 22 0>; interrupt-names = "ack", "err", "wakeup"; - #address-cells = <1>; - #size-cells = <0>; + regulators { + compatible = "qcom,rpm-pm8921-regulators"; + vdd_l1_l2_l12_l18-supply = <&pm8921_s4>; + + s1 { + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1225000>; + + bias-pull-down; + + qcom,switch-mode-frequency = <3200000>; + }; + + pm8921_s4: s4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + qcom,switch-mode-frequency = <1600000>; + bias-pull-down; + + qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>; + }; + }; }; diff --git a/dts/Bindings/mfd/sky81452.txt b/dts/Bindings/mfd/sky81452.txt new file mode 100644 index 0000000000..35181794aa --- /dev/null +++ b/dts/Bindings/mfd/sky81452.txt @@ -0,0 +1,35 @@ +SKY81452 bindings + +Required properties: +- compatible : Must be "skyworks,sky81452" +- reg : I2C slave address + +Required child nodes: +- backlight : container node for backlight following the binding + in video/backlight/sky81452-backlight.txt +- regulator : container node for regulators following the binding + in regulator/sky81452-regulator.txt + +Example: + + sky81452@2c { + compatible = "skyworks,sky81452"; + reg = <0x2c>; + + backlight { + compatible = "skyworks,sky81452-backlight"; + name = "pwm-backlight"; + led-sources = <0 1 2 3 6>; + skyworks,ignore-pwm; + skyworks,phase-shift; + skyworks,current-limit = <2300>; + }; + + regulator { + lout { + regulator-name = "sky81452-lout"; + regulator-min-microvolt = <4500000>; + regulator-max-microvolt = <8000000>; + }; + }; + }; diff --git a/dts/Bindings/mips/brcm/bcm3384-intc.txt b/dts/Bindings/mips/brcm/bcm3384-intc.txt deleted file mode 100644 index d4e0141d36..0000000000 --- a/dts/Bindings/mips/brcm/bcm3384-intc.txt +++ /dev/null @@ -1,37 +0,0 @@ -* Interrupt Controller - -Properties: -- compatible: "brcm,bcm3384-intc" - - Compatibility with BCM3384 and possibly other BCM33xx/BCM63xx SoCs. - -- reg: Address/length pairs for each mask/status register set. Length must - be 8. If multiple register sets are specified, the first set will - handle IRQ offsets 0..31, the second set 32..63, and so on. - -- interrupt-controller: This is an interrupt controller. - -- #interrupt-cells: Must be <1>. Just a simple IRQ offset; no level/edge - or polarity configuration is possible with this controller. - -- interrupt-parent: This controller is cascaded from a MIPS CPU HW IRQ, or - from another INTC. - -- interrupts: The IRQ on the parent controller. - -Example: - periph_intc: periph_intc@14e00038 { - compatible = "brcm,bcm3384-intc"; - - /* - * IRQs 0..31: mask reg 0x14e00038, status reg 0x14e0003c - * IRQs 32..63: mask reg 0x14e00340, status reg 0x14e00344 - */ - reg = <0x14e00038 0x8 0x14e00340 0x8>; - - interrupt-controller; - #interrupt-cells = <1>; - - interrupt-parent = <&cpu_intc>; - interrupts = <4>; - }; diff --git a/dts/Bindings/mips/brcm/bmips.txt b/dts/Bindings/mips/brcm/brcm,bmips.txt index 8ef71b4085..8ef71b4085 100644 --- a/dts/Bindings/mips/brcm/bmips.txt +++ b/dts/Bindings/mips/brcm/brcm,bmips.txt diff --git a/dts/Bindings/mips/brcm/cm-dsl.txt b/dts/Bindings/mips/brcm/cm-dsl.txt deleted file mode 100644 index 8a139cb3c0..0000000000 --- a/dts/Bindings/mips/brcm/cm-dsl.txt +++ /dev/null @@ -1,11 +0,0 @@ -* Broadcom cable/DSL platforms - -SoCs: - -Required properties: -- compatible: "brcm,bcm3384", "brcm,bcm33843" - -Boards: - -Required properties: -- compatible: "brcm,bcm93384wvg" diff --git a/dts/Bindings/mips/brcm/soc.txt b/dts/Bindings/mips/brcm/soc.txt new file mode 100644 index 0000000000..7bab90cc4a --- /dev/null +++ b/dts/Bindings/mips/brcm/soc.txt @@ -0,0 +1,12 @@ +* Broadcom cable/DSL/settop platforms + +Required properties: + +- compatible: "brcm,bcm3384", "brcm,bcm33843" + "brcm,bcm3384-viper", "brcm,bcm33843-viper" + "brcm,bcm6328", "brcm,bcm6368", + "brcm,bcm7125", "brcm,bcm7346", "brcm,bcm7358", "brcm,bcm7360", + "brcm,bcm7362", "brcm,bcm7420", "brcm,bcm7425" + +The experimental -viper variants are for running Linux on the 3384's +BMIPS4355 cable modem CPU instead of the BMIPS5000 application processor. diff --git a/dts/Bindings/mips/img/pistachio.txt b/dts/Bindings/mips/img/pistachio.txt new file mode 100644 index 0000000000..a736d889c2 --- /dev/null +++ b/dts/Bindings/mips/img/pistachio.txt @@ -0,0 +1,42 @@ +Imagination Pistachio SoC +========================= + +Required properties: +-------------------- + - compatible: Must include "img,pistachio". + +CPU nodes: +---------- +A "cpus" node is required. Required properties: + - #address-cells: Must be 1. + - #size-cells: Must be 0. +A CPU sub-node is also required for at least CPU 0. Since the topology may +be probed via CPS, it is not necessary to specify secondary CPUs. Required +propertis: + - device_type: Must be "cpu". + - compatible: Must be "mti,interaptiv". + - reg: CPU number. + - clocks: Must include the CPU clock. See ../../clock/clock-bindings.txt for + details on clock bindings. +Example: + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "mti,interaptiv"; + reg = <0>; + clocks = <&clk_core CLK_MIPS>; + }; + }; + + +Boot protocol: +-------------- +In accordance with the MIPS UHI specification[1], the bootloader must pass the +following arguments to the kernel: + - $a0: -2. + - $a1: KSEG0 address of the flattened device-tree blob. + +[1] http://prplfoundation.org/wiki/MIPS_documentation diff --git a/dts/Bindings/misc/smc.txt b/dts/Bindings/misc/brcm,kona-smc.txt index 6c9f176f35..6c9f176f35 100644 --- a/dts/Bindings/misc/smc.txt +++ b/dts/Bindings/misc/brcm,kona-smc.txt diff --git a/dts/Bindings/misc/lis302.txt b/dts/Bindings/misc/lis302.txt index 6def86f6b0..2a19bff969 100644 --- a/dts/Bindings/misc/lis302.txt +++ b/dts/Bindings/misc/lis302.txt @@ -46,11 +46,18 @@ Optional properties for all bus drivers: interrupt 2 - st,wakeup-{x,y,z}-{lo,hi}: set wakeup condition on x/y/z axis for upper/lower limit + - st,wakeup-threshold: set wakeup threshold + - st,wakeup2-{x,y,z}-{lo,hi}: set wakeup condition on x/y/z axis for + upper/lower limit for second wakeup + engine. + - st,wakeup2-threshold: set wakeup threshold for second wakeup + engine. - st,highpass-cutoff-hz=: 1, 2, 4 or 8 for 1Hz, 2Hz, 4Hz or 8Hz of highpass cut-off frequency - st,hipass{1,2}-disable: disable highpass 1/2. - st,default-rate=: set the default rate - - st,axis-{x,y,z}=: set the axis to map to the three coordinates + - st,axis-{x,y,z}=: set the axis to map to the three coordinates. + Negative values can be used for inverted axis. - st,{min,max}-limit-{x,y,z} set the min/max limits for x/y/z axis (used by self-test) diff --git a/dts/Bindings/mmc/kona-sdhci.txt b/dts/Bindings/mmc/brcm,kona-sdhci.txt index aaba2483b4..aaba2483b4 100644 --- a/dts/Bindings/mmc/kona-sdhci.txt +++ b/dts/Bindings/mmc/brcm,kona-sdhci.txt diff --git a/dts/Bindings/mmc/brcm,sdhci-iproc.txt b/dts/Bindings/mmc/brcm,sdhci-iproc.txt new file mode 100644 index 0000000000..72cc9cc958 --- /dev/null +++ b/dts/Bindings/mmc/brcm,sdhci-iproc.txt @@ -0,0 +1,23 @@ +Broadcom IPROC SDHCI controller + +This file documents differences between the core properties described +by mmc.txt and the properties that represent the IPROC SDHCI controller. + +Required properties: +- compatible : Should be "brcm,sdhci-iproc-cygnus". +- clocks : The clock feeding the SDHCI controller. + +Optional properties: + - sdhci,auto-cmd12: specifies that controller should use auto CMD12. + +Example: + +sdhci0: sdhci@0x18041000 { + compatible = "brcm,sdhci-iproc-cygnus"; + reg = <0x18041000 0x100>; + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&lcpll0_clks BCM_CYGNUS_LCPLL0_SDIO_CLK>; + bus-width = <4>; + sdhci,auto-cmd12; + no-1-8-v; +}; diff --git a/dts/Bindings/mmc/exynos-dw-mshc.txt b/dts/Bindings/mmc/exynos-dw-mshc.txt index ee4fc0576c..aad9844278 100644 --- a/dts/Bindings/mmc/exynos-dw-mshc.txt +++ b/dts/Bindings/mmc/exynos-dw-mshc.txt @@ -36,6 +36,8 @@ Required Properties: in transmit mode and CIU clock phase shift value in receive mode for double data rate mode operation. Refer notes below for the order of the cells and the valid values. +* samsung,dw-mshc-hs400-timing: Specifies the value of CIU TX and RX clock phase + shift value for hs400 mode operation. Notes for the sdr-timing and ddr-timing values: @@ -50,6 +52,9 @@ Required Properties: - if CIU clock divider value is 0 (that is divide by 1), both tx and rx phase shift clocks should be 0. +* samsung,read-strobe-delay: RCLK (Data strobe) delay to control HS400 mode + (Latency value for delay line in Read path) + Required properties for a slot (Deprecated - Recommend to use one slot per host): * gpios: specifies a list of gpios used for command, clock and data bus. The @@ -82,5 +87,7 @@ Example: samsung,dw-mshc-ciu-div = <3>; samsung,dw-mshc-sdr-timing = <2 3>; samsung,dw-mshc-ddr-timing = <1 2>; + samsung,dw-mshc-hs400-timing = <0 2>; + samsung,read-strobe-delay = <90>; bus-width = <8>; }; diff --git a/dts/Bindings/mmc/fsl-imx-esdhc.txt b/dts/Bindings/mmc/fsl-imx-esdhc.txt index 9046ba06c4..415c5575cb 100644 --- a/dts/Bindings/mmc/fsl-imx-esdhc.txt +++ b/dts/Bindings/mmc/fsl-imx-esdhc.txt @@ -17,6 +17,10 @@ Optional properties: to select a proper data sampling window in case the clock quality is not good due to signal path is too long on the board. Please refer to eSDHC/uSDHC chapter, DLL (Delay Line) section in RM for details. +- voltage-ranges : Specify the voltage range in case there are software + transparent level shifters on the outputs of the controller. Two cells are + required, first cell specifies minimum slot voltage (mV), second cell + specifies maximum slot voltage (mV). Several ranges could be specified. Examples: diff --git a/dts/Bindings/mmc/mmc-card.txt b/dts/Bindings/mmc/mmc-card.txt new file mode 100644 index 0000000000..a70fcd65b9 --- /dev/null +++ b/dts/Bindings/mmc/mmc-card.txt @@ -0,0 +1,31 @@ +mmc-card / eMMC bindings +------------------------ + +This documents describes the devicetree bindings for a mmc-host controller +child node describing a mmc-card / an eMMC, see "Use of Function subnodes" +in mmc.txt + +Required properties: +-compatible : Must be "mmc-card" +-reg : Must be <0> + +Optional properties: +-broken-hpi : Use this to indicate that the mmc-card has a broken hpi + implementation, and that hpi should not be used + +Example: + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins_a>; + vmmc-supply = <®_vcc3v3>; + bus-width = <8>; + non-removable; + status = "okay"; + + mmccard: mmccard@0 { + reg = <0>; + compatible = "mmc-card"; + broken-hpi; + }; +}; diff --git a/dts/Bindings/mmc/sdhci-st.txt b/dts/Bindings/mmc/sdhci-st.txt index 7527db447a..18d950df27 100644 --- a/dts/Bindings/mmc/sdhci-st.txt +++ b/dts/Bindings/mmc/sdhci-st.txt @@ -5,20 +5,62 @@ Documentation/devicetree/bindings/mmc/mmc.txt and the properties used by the sdhci-st driver. Required properties: -- compatible : Must be "st,sdhci" -- clock-names : Should be "mmc" - See: Documentation/devicetree/bindings/resource-names.txt -- clocks : Phandle of the clock used by the sdhci controler - See: Documentation/devicetree/bindings/clock/clock-bindings.txt +- compatible: Must be "st,sdhci" and it can be compatible to "st,sdhci-stih407" + to set the internal glue logic used for configuring the MMC + subsystem (mmcss) inside the FlashSS (available in STiH407 SoC + family). + +- clock-names: Should be "mmc". + See: Documentation/devicetree/bindings/resource-names.txt +- clocks: Phandle to the clock. + See: Documentation/devicetree/bindings/clock/clock-bindings.txt + +- interrupts: One mmc interrupt should be described here. +- interrupt-names: Should be "mmcirq". + +- pinctrl-names: A pinctrl state names "default" must be defined. +- pinctrl-0: Phandle referencing pin configuration of the sd/emmc controller. + See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt + +- reg: This must provide the host controller base address and it can also + contain the FlashSS Top register for TX/RX delay used by the driver + to configure DLL inside the flashSS, if so reg-names must also be + specified. Optional properties: -- non-removable: non-removable slot - See: Documentation/devicetree/bindings/mmc/mmc.txt -- bus-width: Number of data lines - See: Documentation/devicetree/bindings/mmc/mmc.txt +- reg-names: Should be "mmc" and "top-mmc-delay". "top-mmc-delay" is optional + for eMMC on stih407 family silicon to configure DLL inside FlashSS. + +- non-removable: Non-removable slot. Also used for configuring mmcss in STiH407 SoC + family. + See: Documentation/devicetree/bindings/mmc/mmc.txt. + +- bus-width: Number of data lines. + See: Documentation/devicetree/bindings/mmc/mmc.txt. + +- max-frequency: Can be 200MHz, 100Mz or 50MHz (default) and used for + configuring the CCONFIG3 in the mmcss. + See: Documentation/devicetree/bindings/mmc/mmc.txt. + +- resets: Phandle and reset specifier pair to softreset line of HC IP. + See: Documentation/devicetree/bindings/reset/reset.txt + +- vqmmc-supply: Phandle to the regulator dt node, mentioned as the vcc/vdd + supply in eMMC/SD specs. + +- sd-uhs--sdr50: To enable the SDR50 in the mmcss. + See: Documentation/devicetree/bindings/mmc/mmc.txt. + +- sd-uhs-sdr104: To enable the SDR104 in the mmcss. + See: Documentation/devicetree/bindings/mmc/mmc.txt. + +- sd-uhs-ddr50: To enable the DDR50 in the mmcss. + See: Documentation/devicetree/bindings/mmc/mmc.txt. Example: +/* Example stih416e eMMC configuration */ + mmc0: sdhci@fe81e000 { compatible = "st,sdhci"; status = "disabled"; @@ -29,5 +71,43 @@ mmc0: sdhci@fe81e000 { pinctrl-0 = <&pinctrl_mmc0>; clock-names = "mmc"; clocks = <&clk_s_a1_ls 1>; - bus-width = <8> + bus-width = <8> + +/* Example SD stih407 family configuration */ + +mmc1: sdhci@09080000 { + compatible = "st,sdhci-stih407", "st,sdhci"; + status = "disabled"; + reg = <0x09080000 0x7ff>; + reg-names = "mmc"; + interrupts = <GIC_SPI 90 IRQ_TYPE_NONE>; + interrupt-names = "mmcirq"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sd1>; + clock-names = "mmc"; + clocks = <&clk_s_c0_flexgen CLK_MMC_1>; + resets = <&softreset STIH407_MMC1_SOFTRESET>; + bus-width = <4>; +}; + +/* Example eMMC stih407 family configuration */ + +mmc0: sdhci@09060000 { + compatible = "st,sdhci-stih407", "st,sdhci"; + status = "disabled"; + reg = <0x09060000 0x7ff>, <0x9061008 0x20>; + reg-names = "mmc", "top-mmc-delay"; + interrupts = <GIC_SPI 92 IRQ_TYPE_NONE>; + interrupt-names = "mmcirq"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mmc0>; + clock-names = "mmc"; + clocks = <&clk_s_c0_flexgen CLK_MMC_0>; + vqmmc-supply = <&vmmc_reg>; + max-frequency = <200000000>; + bus-width = <8>; + non-removable; + sd-uhs-sdr50; + sd-uhs-sdr104; + sd-uhs-ddr50; }; diff --git a/dts/Bindings/mtd/m25p80.txt b/dts/Bindings/mtd/m25p80.txt index 4611aa8353..f20b111b50 100644 --- a/dts/Bindings/mtd/m25p80.txt +++ b/dts/Bindings/mtd/m25p80.txt @@ -3,10 +3,13 @@ Required properties: - #address-cells, #size-cells : Must be present if the device has sub-nodes representing partitions. -- compatible : Should be the manufacturer and the name of the chip. Bear in mind - the DT binding is not Linux-only, but in case of Linux, see the - "spi_nor_ids" table in drivers/mtd/spi-nor/spi-nor.c for the list - of supported chips. +- compatible : May include a device-specific string consisting of the + manufacturer and name of the chip. Bear in mind the DT binding + is not Linux-only, but in case of Linux, see the "m25p_ids" + table in drivers/mtd/devices/m25p80.c for the list of supported + chips. + Must also include "nor-jedec" for any SPI NOR flash that can be + identified by the JEDEC READ ID opcode (0x9F). - reg : Chip-Select number - spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at @@ -22,7 +25,7 @@ Example: flash: m25p80@0 { #address-cells = <1>; #size-cells = <1>; - compatible = "spansion,m25p80"; + compatible = "spansion,m25p80", "nor-jedec"; reg = <0>; spi-max-frequency = <40000000>; m25p,fast-read; diff --git a/dts/Bindings/mtd/pxa3xx-nand.txt b/dts/Bindings/mtd/pxa3xx-nand.txt index de8b517a55..4f833e3c4f 100644 --- a/dts/Bindings/mtd/pxa3xx-nand.txt +++ b/dts/Bindings/mtd/pxa3xx-nand.txt @@ -14,7 +14,7 @@ Optional properties: - marvell,nand-enable-arbiter: Set to enable the bus arbiter - marvell,nand-keep-config: Set to keep the NAND controller config as set by the bootloader - - num-cs: Number of chipselect lines to usw + - num-cs: Number of chipselect lines to use - nand-on-flash-bbt: boolean to enable on flash bbt option if not present false - nand-ecc-strength: number of bits to correct per ECC step diff --git a/dts/Bindings/mtd/sunxi-nand.txt b/dts/Bindings/mtd/sunxi-nand.txt index 0273adb863..086d6f44c4 100644 --- a/dts/Bindings/mtd/sunxi-nand.txt +++ b/dts/Bindings/mtd/sunxi-nand.txt @@ -21,7 +21,7 @@ Optional properties: - nand-ecc-mode : one of the supported ECC modes ("hw", "hw_syndrome", "soft", "soft_bch" or "none") -see Documentation/devicetree/mtd/nand.txt for generic bindings. +see Documentation/devicetree/bindings/mtd/nand.txt for generic bindings. Examples: diff --git a/dts/Bindings/net/apm-xgene-enet.txt b/dts/Bindings/net/apm-xgene-enet.txt index 6151999c5d..f55aa280d3 100644 --- a/dts/Bindings/net/apm-xgene-enet.txt +++ b/dts/Bindings/net/apm-xgene-enet.txt @@ -14,7 +14,11 @@ Required properties for all the ethernet interfaces: - "enet_csr": Ethernet control and status register address space - "ring_csr": Descriptor ring control and status register address space - "ring_cmd": Descriptor ring command register address space -- interrupts: Ethernet main interrupt +- interrupts: Two interrupt specifiers can be specified. + - First is the Rx interrupt. This irq is mandatory. + - Second is the Tx completion interrupt. + This is supported only on SGMII based 1GbE and 10GbE interfaces. +- port-id: Port number (0 or 1) - clocks: Reference to the clock entry. - local-mac-address: MAC address assigned to this device - phy-connection-type: Interface type between ethernet device and PHY device @@ -49,6 +53,7 @@ Example: <0x0 0X10000000 0x0 0X200>; reg-names = "enet_csr", "ring_csr", "ring_cmd"; interrupts = <0x0 0x3c 0x4>; + port-id = <0>; clocks = <&menetclk 0>; local-mac-address = [00 01 73 00 00 01]; phy-connection-type = "rgmii"; diff --git a/dts/Bindings/net/broadcom-sf2.txt b/dts/Bindings/net/brcm,bcm7445-switch-v4.0.txt index 30d487597e..30d487597e 100644 --- a/dts/Bindings/net/broadcom-sf2.txt +++ b/dts/Bindings/net/brcm,bcm7445-switch-v4.0.txt diff --git a/dts/Bindings/net/broadcom-bcmgenet.txt b/dts/Bindings/net/brcm,bcmgenet.txt index 451fef26b4..451fef26b4 100644 --- a/dts/Bindings/net/broadcom-bcmgenet.txt +++ b/dts/Bindings/net/brcm,bcmgenet.txt diff --git a/dts/Bindings/net/broadcom-systemport.txt b/dts/Bindings/net/brcm,systemport.txt index 877da34145..877da34145 100644 --- a/dts/Bindings/net/broadcom-systemport.txt +++ b/dts/Bindings/net/brcm,systemport.txt diff --git a/dts/Bindings/net/broadcom-mdio-unimac.txt b/dts/Bindings/net/brcm,unimac-mdio.txt index ab0bb4247d..ab0bb4247d 100644 --- a/dts/Bindings/net/broadcom-mdio-unimac.txt +++ b/dts/Bindings/net/brcm,unimac-mdio.txt diff --git a/dts/Bindings/net/ethernet.txt b/dts/Bindings/net/ethernet.txt index 3fc360523b..41b3f3f864 100644 --- a/dts/Bindings/net/ethernet.txt +++ b/dts/Bindings/net/ethernet.txt @@ -19,6 +19,12 @@ The following properties are common to the Ethernet controllers: - phy: the same as "phy-handle" property, not recommended for new bindings. - phy-device: the same as "phy-handle" property, not recommended for new bindings. +- rx-fifo-depth: the size of the controller's receive fifo in bytes. This + is used for components that can have configurable receive fifo sizes, + and is useful for determining certain configuration settings such as + flow control thresholds. +- tx-fifo-depth: the size of the controller's transmit fifo in bytes. This + is used for components that can have configurable fifo sizes. Child nodes of the Ethernet controller are typically the individual PHY devices connected via the MDIO bus (sometimes the MDIO bus controller is separate). diff --git a/dts/Bindings/net/ieee802154/at86rf230.txt b/dts/Bindings/net/ieee802154/at86rf230.txt index d3bbdded4c..168f1be509 100644 --- a/dts/Bindings/net/ieee802154/at86rf230.txt +++ b/dts/Bindings/net/ieee802154/at86rf230.txt @@ -6,11 +6,14 @@ Required properties: - spi-max-frequency: maximal bus speed, should be set to 7500000 depends sync or async operation mode - reg: the chipselect index - - interrupts: the interrupt generated by the device + - interrupts: the interrupt generated by the device. Non high-level + can occur deadlocks while handling isr. Optional properties: - reset-gpio: GPIO spec for the rstn pin - sleep-gpio: GPIO spec for the slp_tr pin + - xtal-trim: u8 value for fine tuning the internal capacitance + arrays of xtal pins: 0 = +0 pF, 0xf = +4.5 pF Example: @@ -18,6 +21,7 @@ Example: compatible = "atmel,at86rf231"; spi-max-frequency = <7500000>; reg = <0>; - interrupts = <19 1>; + interrupts = <19 4>; interrupt-parent = <&gpio3>; + xtal-trim = /bits/ 8 <0x06>; }; diff --git a/dts/Bindings/net/ieee802154/cc2520.txt b/dts/Bindings/net/ieee802154/cc2520.txt index 0071883c08..fb6d49f184 100644 --- a/dts/Bindings/net/ieee802154/cc2520.txt +++ b/dts/Bindings/net/ieee802154/cc2520.txt @@ -13,11 +13,15 @@ Required properties: - cca-gpio: GPIO spec for the CCA pin - vreg-gpio: GPIO spec for the VREG pin - reset-gpio: GPIO spec for the RESET pin +Optional properties: + - amplified: include if the CC2520 is connected to a CC2591 amplifier + Example: cc2520@0 { compatible = "ti,cc2520"; reg = <0>; spi-max-frequency = <4000000>; + amplified; pinctrl-names = "default"; pinctrl-0 = <&cc2520_cape_pins>; fifo-gpio = <&gpio1 18 0>; diff --git a/dts/Bindings/net/keystone-netcp.txt b/dts/Bindings/net/keystone-netcp.txt index f9c0771047..d0e6fa38f3 100644 --- a/dts/Bindings/net/keystone-netcp.txt +++ b/dts/Bindings/net/keystone-netcp.txt @@ -49,6 +49,7 @@ Required properties: - compatible: Should be "ti,netcp-1.0" - clocks: phandle to the reference clocks for the subsystem. - dma-id: Navigator packet dma instance id. +- ranges: address range of NetCP (includes, Ethernet SS, PA and SA) Optional properties: - reg: register location and the size for the following register @@ -64,10 +65,30 @@ NetCP device properties: Device specification for NetCP sub-modules. 1Gb/10Gb (gbe/xgbe) ethernet switch sub-module specifications. Required properties: - label: Must be "netcp-gbe" for 1Gb & "netcp-xgbe" for 10Gb. +- compatible: Must be one of below:- + "ti,netcp-gbe" for 1GbE on NetCP 1.4 + "ti,netcp-gbe-5" for 1GbE N NetCP 1.5 (N=5) + "ti,netcp-gbe-9" for 1GbE N NetCP 1.5 (N=9) + "ti,netcp-gbe-2" for 1GbE N NetCP 1.5 (N=2) + "ti,netcp-xgbe" for 10 GbE + - reg: register location and the size for the following register regions in the specified order. - - subsystem registers - - serdes registers + - switch subsystem registers + - sgmii port3/4 module registers (only for NetCP 1.4) + - switch module registers + - serdes registers (only for 10G) + + NetCP 1.4 ethss, here is the order + index #0 - switch subsystem registers + index #1 - sgmii port3/4 module registers + index #2 - switch module registers + + NetCP 1.5 ethss 9 port, 5 port and 2 port + index #0 - switch subsystem registers + index #1 - switch module registers + index #2 - serdes registers + - tx-channel: the navigator packet dma channel name for tx. - tx-queue: the navigator queue number associated with the tx dma channel. - interfaces: specification for each of the switch port to be registered as a @@ -120,14 +141,13 @@ Optional properties: Example binding: -netcp: netcp@2090000 { +netcp: netcp@2000000 { reg = <0x2620110 0x8>; reg-names = "efuse"; compatible = "ti,netcp-1.0"; #address-cells = <1>; #size-cells = <1>; - ranges; - + ranges = <0 0x2000000 0xfffff>; clocks = <&papllclk>, <&clkcpgmac>, <&chipclk12>; dma-coherent; /* big-endian; */ @@ -137,9 +157,9 @@ netcp: netcp@2090000 { #address-cells = <1>; #size-cells = <1>; ranges; - gbe@0x2090000 { + gbe@90000 { label = "netcp-gbe"; - reg = <0x2090000 0xf00>; + reg = <0x90000 0x300>, <0x90400 0x400>, <0x90800 0x700>; /* enable-ale; */ tx-queue = <648>; tx-channel = <8>; diff --git a/dts/Bindings/net/macb.txt b/dts/Bindings/net/macb.txt index aaa696414f..ba19d671e8 100644 --- a/dts/Bindings/net/macb.txt +++ b/dts/Bindings/net/macb.txt @@ -2,10 +2,13 @@ Required properties: - compatible: Should be "cdns,[<chip>-]{macb|gem}" - Use "cdns,at91sam9260-macb" Atmel at91sam9260 and at91sam9263 SoCs. + Use "cdns,at91sam9260-macb" for Atmel at91sam9 SoCs or the 10/100Mbit IP + available on sama5d3 SoCs. Use "cdns,at32ap7000-macb" for other 10/100 usage or use the generic form: "cdns,macb". Use "cdns,pc302-gem" for Picochip picoXcell pc302 and later devices based on the Cadence GEM, or the generic form: "cdns,gem". + Use "cdns,sama5d3-gem" for the Gigabit IP available on Atmel sama5d3 SoCs. + Use "cdns,sama5d4-gem" for the Gigabit IP available on Atmel sama5d4 SoCs. - reg: Address and length of the register set for the device - interrupts: Should contain macb interrupt - phy-mode: See ethernet.txt file in the same directory. diff --git a/dts/Bindings/net/nfc/nxp-nci.txt b/dts/Bindings/net/nfc/nxp-nci.txt new file mode 100644 index 0000000000..5b6cd9b3f6 --- /dev/null +++ b/dts/Bindings/net/nfc/nxp-nci.txt @@ -0,0 +1,35 @@ +* NXP Semiconductors NXP NCI NFC Controllers + +Required properties: +- compatible: Should be "nxp,nxp-nci-i2c". +- clock-frequency: I²C work frequency. +- reg: address on the bus +- interrupt-parent: phandle for the interrupt gpio controller +- interrupts: GPIO interrupt to which the chip is connected +- enable-gpios: Output GPIO pin used for enabling/disabling the chip +- firmware-gpios: Output GPIO pin used to enter firmware download mode + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. + +Example (for ARM-based BeagleBone with NPC100 NFC controller on I2C2): + +&i2c2 { + + status = "okay"; + + npc100: npc100@29 { + + compatible = "nxp,nxp-nci-i2c"; + + reg = <0x29>; + clock-frequency = <100000>; + + interrupt-parent = <&gpio1>; + interrupts = <29 GPIO_ACTIVE_HIGH>; + + enable-gpios = <&gpio0 30 GPIO_ACTIVE_HIGH>; + firmware-gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>; + }; +}; diff --git a/dts/Bindings/net/stmmac.txt b/dts/Bindings/net/stmmac.txt index 8ca65cec52..f34fc3c81a 100644 --- a/dts/Bindings/net/stmmac.txt +++ b/dts/Bindings/net/stmmac.txt @@ -35,15 +35,18 @@ Optional properties: - reset-names: Should contain the reset signal name "stmmaceth", if a reset phandle is given - max-frame-size: See ethernet.txt file in the same directory -- clocks: If present, the first clock should be the GMAC main clock, - further clocks may be specified in derived bindings. +- clocks: If present, the first clock should be the GMAC main clock and + the second clock should be peripheral's register interface clock. Further + clocks may be specified in derived bindings. - clock-names: One name for each entry in the clocks property, the - first one should be "stmmaceth". + first one should be "stmmaceth" and the second one should be "pclk". - clk_ptp_ref: this is the PTP reference clock; in case of the PTP is available this clock is used for programming the Timestamp Addend Register. If not passed then the system clock will be used and this is fine on some platforms. - snps,burst_len: The AXI burst lenth value of the AXI BUS MODE register. +- tx-fifo-depth: See ethernet.txt file in the same directory +- rx-fifo-depth: See ethernet.txt file in the same directory Examples: @@ -58,6 +61,8 @@ Examples: phy-mode = "gmii"; snps,multicast-filter-bins = <256>; snps,perfect-filter-entries = <128>; + rx-fifo-depth = <16384>; + tx-fifo-depth = <16384>; clocks = <&clock>; clock-names = "stmmaceth"; }; diff --git a/dts/Bindings/net/wireless/ti,wlcore.txt b/dts/Bindings/net/wireless/ti,wlcore.txt new file mode 100644 index 0000000000..2a3d90de18 --- /dev/null +++ b/dts/Bindings/net/wireless/ti,wlcore.txt @@ -0,0 +1,47 @@ +TI Wilink 6/7/8 (wl12xx/wl18xx) SDIO devices + +This node provides properties for controlling the wilink wireless device. The +node is expected to be specified as a child node to the SDIO controller that +connects the device to the system. + +Required properties: + - compatible: should be one of the following: + * "ti,wl1271" + * "ti,wl1273" + * "ti,wl1281" + * "ti,wl1283" + * "ti,wl1801" + * "ti,wl1805" + * "ti,wl1807" + * "ti,wl1831" + * "ti,wl1835" + * "ti,wl1837" + - interrupts : specifies attributes for the out-of-band interrupt. + +Optional properties: + - interrupt-parent : the phandle for the interrupt controller to which the + device interrupts are connected. + - ref-clock-frequency : ref clock frequency in Hz + - tcxo-clock-frequency : tcxo clock frequency in Hz + +Note: the *-clock-frequency properties assume internal clocks. In case of external +clock, new bindings (for parsing the clock nodes) have to be added. + +Example: + +&mmc3 { + status = "okay"; + vmmc-supply = <&wlan_en_reg>; + bus-width = <4>; + cap-power-off-card; + keep-power-in-suspend; + + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@2 { + compatible = "ti,wl1835"; + reg = <2>; + interrupt-parent = <&gpio0>; + interrupts = <19 IRQ_TYPE_LEVEL_HIGH>; + }; +}; diff --git a/dts/Bindings/panel/ampire,am800480r3tmqwa1h.txt b/dts/Bindings/panel/ampire,am800480r3tmqwa1h.txt new file mode 100644 index 0000000000..83e2cae1cc --- /dev/null +++ b/dts/Bindings/panel/ampire,am800480r3tmqwa1h.txt @@ -0,0 +1,7 @@ +Ampire AM-800480R3TMQW-A1H 7.0" WVGA TFT LCD panel + +Required properties: +- compatible: should be "ampire,am800480r3tmqwa1h" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/dts/Bindings/panel/auo,b101ean01.txt b/dts/Bindings/panel/auo,b101ean01.txt new file mode 100644 index 0000000000..3590b07416 --- /dev/null +++ b/dts/Bindings/panel/auo,b101ean01.txt @@ -0,0 +1,7 @@ +AU Optronics Corporation 10.1" WSVGA TFT LCD panel + +Required properties: +- compatible: should be "auo,b101ean01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/dts/Bindings/panel/innolux,at043tn24.txt b/dts/Bindings/panel/innolux,at043tn24.txt new file mode 100644 index 0000000000..4104226b61 --- /dev/null +++ b/dts/Bindings/panel/innolux,at043tn24.txt @@ -0,0 +1,7 @@ +Innolux AT043TN24 4.3" WQVGA TFT LCD panel + +Required properties: +- compatible: should be "innolux,at043tn24" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/dts/Bindings/panel/innolux,zj070na-01p.txt b/dts/Bindings/panel/innolux,zj070na-01p.txt new file mode 100644 index 0000000000..824f87f152 --- /dev/null +++ b/dts/Bindings/panel/innolux,zj070na-01p.txt @@ -0,0 +1,7 @@ +Innolux Corporation 7.0" WSVGA (1024x600) TFT LCD panel + +Required properties: +- compatible: should be "innolux,zj070na-01p" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/dts/Bindings/panel/ortustech,com43h4m85ulc.txt b/dts/Bindings/panel/ortustech,com43h4m85ulc.txt new file mode 100644 index 0000000000..de19e93986 --- /dev/null +++ b/dts/Bindings/panel/ortustech,com43h4m85ulc.txt @@ -0,0 +1,7 @@ +OrtusTech COM43H4M85ULC Blanview 3.7" TFT-LCD panel + +Required properties: +- compatible: should be "ortustech,com43h4m85ulc" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/dts/Bindings/panel/samsung,ltn140at29-301.txt b/dts/Bindings/panel/samsung,ltn140at29-301.txt new file mode 100644 index 0000000000..e7f969d891 --- /dev/null +++ b/dts/Bindings/panel/samsung,ltn140at29-301.txt @@ -0,0 +1,7 @@ +Samsung Electronics 14" WXGA (1366x768) TFT LCD panel + +Required properties: +- compatible: should be "samsung,ltn140at29-301" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/dts/Bindings/panel/shelly,sca07010-bfn-lnn.txt b/dts/Bindings/panel/shelly,sca07010-bfn-lnn.txt new file mode 100644 index 0000000000..fc1ea9e26c --- /dev/null +++ b/dts/Bindings/panel/shelly,sca07010-bfn-lnn.txt @@ -0,0 +1,7 @@ +Shelly SCA07010-BFN-LNN 7.0" WVGA TFT LCD panel + +Required properties: +- compatible: should be "shelly,sca07010-bfn-lnn" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/dts/Bindings/pci/brcm,iproc-pcie.txt b/dts/Bindings/pci/brcm,iproc-pcie.txt new file mode 100644 index 0000000000..f7ce50e38e --- /dev/null +++ b/dts/Bindings/pci/brcm,iproc-pcie.txt @@ -0,0 +1,63 @@ +* Broadcom iProc PCIe controller with the platform bus interface + +Required properties: +- compatible: Must be "brcm,iproc-pcie" +- reg: base address and length of the PCIe controller I/O register space +- #interrupt-cells: set to <1> +- interrupt-map-mask and interrupt-map, standard PCI properties to define the + mapping of the PCIe interface to interrupt numbers +- linux,pci-domain: PCI domain ID. Should be unique for each host controller +- bus-range: PCI bus numbers covered +- #address-cells: set to <3> +- #size-cells: set to <2> +- device_type: set to "pci" +- ranges: ranges for the PCI memory and I/O regions + +Optional properties: +- phys: phandle of the PCIe PHY device +- phy-names: must be "pcie-phy" + +Example: + pcie0: pcie@18012000 { + compatible = "brcm,iproc-pcie"; + reg = <0x18012000 0x1000>; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 100 IRQ_TYPE_NONE>; + + linux,pci-domain = <0>; + + bus-range = <0x00 0xff>; + + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x81000000 0 0 0x28000000 0 0x00010000 + 0x82000000 0 0x20000000 0x20000000 0 0x04000000>; + + phys = <&phy 0 5>; + phy-names = "pcie-phy"; + }; + + pcie1: pcie@18013000 { + compatible = "brcm,iproc-pcie"; + reg = <0x18013000 0x1000>; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 106 IRQ_TYPE_NONE>; + + linux,pci-domain = <1>; + + bus-range = <0x00 0xff>; + + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x81000000 0 0 0x48000000 0 0x00010000 + 0x82000000 0 0x40000000 0x40000000 0 0x04000000>; + + phys = <&phy 1 6>; + phy-names = "pcie-phy"; + }; diff --git a/dts/Bindings/phy/bcm-phy.txt b/dts/Bindings/phy/brcm,kona-usb2-phy.txt index 3dc8b3d2ff..3dc8b3d2ff 100644 --- a/dts/Bindings/phy/bcm-phy.txt +++ b/dts/Bindings/phy/brcm,kona-usb2-phy.txt diff --git a/dts/Bindings/phy/dm816x-phy.txt b/dts/Bindings/phy/dm816x-phy.txt new file mode 100644 index 0000000000..2fe3d11d06 --- /dev/null +++ b/dts/Bindings/phy/dm816x-phy.txt @@ -0,0 +1,24 @@ +Device tree binding documentation for am816x USB PHY +========================= + +Required properties: +- compatible : should be "ti,dm816x-usb-phy" +- reg : offset and length of the PHY register set. +- reg-names : name for the phy registers +- clocks : phandle to the clock +- clock-names : name of the clock +- syscon: phandle for the syscon node to access misc registers +- #phy-cells : from the generic PHY bindings, must be 1 +- syscon: phandle for the syscon node to access misc registers + +Example: + +usb_phy0: usb-phy@20 { + compatible = "ti,dm8168-usb-phy"; + reg = <0x20 0x8>; + reg-names = "phy"; + clocks = <&main_fapll 6>; + clock-names = "refclk"; + #phy-cells = <0>; + syscon = <&scm_conf>; +}; diff --git a/dts/Bindings/phy/phy-miphy365x.txt b/dts/Bindings/phy/phy-miphy365x.txt index 9802d5d911..8772900e05 100644 --- a/dts/Bindings/phy/phy-miphy365x.txt +++ b/dts/Bindings/phy/phy-miphy365x.txt @@ -20,8 +20,8 @@ Required nodes : A sub-node is required for each channel the controller Required properties (port (child) node): - #phy-cells : Should be 1 (See second example) Cell after port phandle is device type from: - - MIPHY_TYPE_SATA - - MIPHY_TYPE_PCI + - PHY_TYPE_SATA + - PHY_TYPE_PCI - reg : Address and length of register sets for each device in "reg-names" - reg-names : The names of the register addresses corresponding to the @@ -68,10 +68,10 @@ property, containing a phandle to the phy port node and a device type. Example: -#include <dt-bindings/phy/phy-miphy365x.h> +#include <dt-bindings/phy/phy.h> sata0: sata@fe380000 { ... - phys = <&phy_port0 MIPHY_TYPE_SATA>; + phys = <&phy_port0 PHY_TYPE_SATA>; ... }; diff --git a/dts/Bindings/phy/samsung-phy.txt b/dts/Bindings/phy/samsung-phy.txt index 91e38cfe1f..60c6f2a633 100644 --- a/dts/Bindings/phy/samsung-phy.txt +++ b/dts/Bindings/phy/samsung-phy.txt @@ -128,6 +128,7 @@ Required properties: - compatible : Should be set to one of the following supported values: - "samsung,exynos5250-usbdrd-phy" - for exynos5250 SoC, - "samsung,exynos5420-usbdrd-phy" - for exynos5420 SoC. + - "samsung,exynos5433-usbdrd-phy" - for exynos5433 SoC. - "samsung,exynos7-usbdrd-phy" - for exynos7 SoC. - reg : Register offset and length of USB DRD PHY register set; - clocks: Clock IDs array as required by the controller @@ -139,7 +140,7 @@ Required properties: PHY operations, associated by phy name. It is used to determine bit values for clock settings register. For Exynos5420 this is given as 'sclk_usbphy30' in CMU. - - optional clocks: Exynos7 SoC has now following additional + - optional clocks: Exynos5433 & Exynos7 SoC has now following additional gate clocks available: - phy_pipe: for PIPE3 phy - phy_utmi: for UTMI+ phy diff --git a/dts/Bindings/phy/sun9i-usb-phy.txt b/dts/Bindings/phy/sun9i-usb-phy.txt new file mode 100644 index 0000000000..1cca85c709 --- /dev/null +++ b/dts/Bindings/phy/sun9i-usb-phy.txt @@ -0,0 +1,38 @@ +Allwinner sun9i USB PHY +----------------------- + +Required properties: +- compatible : should be one of + * allwinner,sun9i-a80-usb-phy +- reg : a list of offset + length pairs +- #phy-cells : from the generic phy bindings, must be 0 +- phy_type : "hsic" for HSIC usage; + other values or absence of this property indicates normal USB +- clocks : phandle + clock specifier for the phy clocks +- clock-names : depending on the "phy_type" property, + * "phy" for normal USB + * "hsic_480M", "hsic_12M" for HSIC +- resets : a list of phandle + reset specifier pairs +- reset-names : depending on the "phy_type" property, + * "phy" for normal USB + * "hsic" for HSIC + +Optional Properties: +- phy-supply : from the generic phy bindings, a phandle to a regulator that + provides power to VBUS. + +It is recommended to list all clocks and resets available. +The driver will only use those matching the phy_type. + +Example: + usbphy1: phy@00a01800 { + compatible = "allwinner,sun9i-a80-usb-phy"; + reg = <0x00a01800 0x4>; + clocks = <&usb_phy_clk 2>, <&usb_phy_clk 10>, + <&usb_phy_clk 3>; + clock-names = "hsic_480M", "hsic_12M", "phy"; + resets = <&usb_phy_clk 18>, <&usb_phy_clk 19>; + reset-names = "hsic", "phy"; + status = "disabled"; + #phy-cells = <0>; + }; diff --git a/dts/Bindings/pinctrl/brcm,cygnus-gpio.txt b/dts/Bindings/pinctrl/brcm,cygnus-gpio.txt new file mode 100644 index 0000000000..6540ca56be --- /dev/null +++ b/dts/Bindings/pinctrl/brcm,cygnus-gpio.txt @@ -0,0 +1,98 @@ +Broadcom Cygnus GPIO/PINCONF Controller + +Required properties: + +- compatible: + Must be "brcm,cygnus-ccm-gpio", "brcm,cygnus-asiu-gpio", or + "brcm,cygnus-crmu-gpio" + +- reg: + Define the base and range of the I/O address space that contains the Cygnus +GPIO/PINCONF controller registers + +- #gpio-cells: + Must be two. The first cell is the GPIO pin number (within the +controller's pin space) and the second cell is used for the following: + bit[0]: polarity (0 for active high and 1 for active low) + +- gpio-controller: + Specifies that the node is a GPIO controller + +Optional properties: + +- interrupts: + Interrupt ID + +- interrupt-controller: + Specifies that the node is an interrupt controller + +- pinmux: + Specifies the phandle to the IOMUX device, where pins can be individually +muxed to GPIO + +Supported generic PINCONF properties in child nodes: + +- pins: + The list of pins (within the controller's own pin space) that properties +in the node apply to. Pin names are "gpio-<pin>" + +- bias-disable: + Disable pin bias + +- bias-pull-up: + Enable internal pull up resistor + +- bias-pull-down: + Enable internal pull down resistor + +- drive-strength: + Valid drive strength values include 2, 4, 6, 8, 10, 12, 14, 16 (mA) + +Example: + gpio_ccm: gpio@1800a000 { + compatible = "brcm,cygnus-ccm-gpio"; + reg = <0x1800a000 0x50>, + <0x0301d164 0x20>; + #gpio-cells = <2>; + gpio-controller; + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + + touch_pins: touch_pins { + pwr: pwr { + pins = "gpio-0"; + drive-strength = <16>; + }; + + event: event { + pins = "gpio-1"; + bias-pull-up; + }; + }; + }; + + gpio_asiu: gpio@180a5000 { + compatible = "brcm,cygnus-asiu-gpio"; + reg = <0x180a5000 0x668>; + #gpio-cells = <2>; + gpio-controller; + interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + }; + + /* + * Touchscreen that uses the CCM GPIO 0 and 1 + */ + tsc { + ... + ... + gpio-pwr = <&gpio_ccm 0 0>; + gpio-event = <&gpio_ccm 1 0>; + }; + + /* Bluetooth that uses the ASIU GPIO 5, with polarity inverted */ + bluetooth { + ... + ... + bcm,rfkill-bank-sel = <&gpio_asiu 5 1> + } diff --git a/dts/Bindings/pinctrl/brcm,cygnus-pinmux.txt b/dts/Bindings/pinctrl/brcm,cygnus-pinmux.txt new file mode 100644 index 0000000000..3600d5c6c4 --- /dev/null +++ b/dts/Bindings/pinctrl/brcm,cygnus-pinmux.txt @@ -0,0 +1,132 @@ +Broadcom Cygnus IOMUX Controller + +The Cygnus IOMUX controller supports group based mux configuration. In +addition, certain pins can be muxed to GPIO function individually. + +Required properties: + +- compatible: + Must be "brcm,cygnus-pinmux" + +- reg: + Define the base and range of the I/O address space that contains the Cygnus +IOMUX registers + +Properties in subnodes: + +- function: + The mux function to select + +- groups: + The list of groups to select with a given function + +For more details, refer to +Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + +For example: + + pinmux: pinmux@0x0301d0c8 { + compatible = "brcm,cygnus-pinmux"; + reg = <0x0301d0c8 0x1b0>; + + pinctrl-names = "default"; + pinctrl-0 = <&i2s0_default>; + + i2s0_default: i2s0_default { + mux { + function = "i2s0"; + groups = "i2s0_0_grp", "i2s0_1_grp"; + }; + }; + }; + +List of supported functions and groups in Cygnus: + +"i2s0": "i2s0_0_grp", "i2s0_1_grp" + +"i2s1": "i2s1_0_grp", "i2s1_1_grp" + +"i2s2": "i2s2_0_grp", "i2s2_1_grp", "i2s2_2_grp", "i2s2_3_grp", "i2s2_4_grp" + +"spdif": "spdif_grp" + +"pwm0": "pwm0_grp" + +"pwm1": "pwm1_grp" + +"pwm2": "pwm2_grp" + +"pwm3": "pwm3_grp" + +"pwm4": "pwm4_grp" + +"pwm5": "pwm5_grp" + +"key": "key0_grp", "key1_grp", "key2_grp", "key3_grp", "key4_grp", "key5_grp", +"key6_grp", "key7_grp", "key8_grp", "key9_grp", "key10_grp", "key11_grp", +"key12_grp", "key13_grp", "key14_grp", "key15_grp" + +"audio_dte": "audio_dte0_grp", "audio_dte1_grp", "audio_dte2_grp", "audio_dte3_grp" + +"smart_card0": "smart_card0_grp", "smart_card0_fcb_grp" + +"smart_card1": "smart_card1_grp", "smart_card1_fcb_grp" + +"spi0": "spi0_grp" + +"spi1": "spi1_grp" + +"spi2": "spi2_grp" + +"spi3": "spi3_grp" + +"spi4": "spi4_0_grp", "spi4_1_grp" + +"spi5": "spi5_grp" + +"sw_led0": "sw_led0_0_grp", "sw_led0_1_grp" + +"sw_led1": "sw_led1_grp" + +"sw_led2": "sw_led2_0_grp", "sw_led2_1_grp" + +"d1w": "d1w_grp" + +"lcd": "lcd_grp" + +"sram": "sram_0_grp", "sram_1_grp" + +"uart0": "uart0_grp" + +"uart1": "uart1_grp", "uart1_dte_grp" + +"uart2": "uart2_grp" + +"uart3": "uart3_grp" + +"uart4": "uart4_grp" + +"qspi": "qspi_0_grp", "qspi_1_grp" + +"nand": "nand_grp" + +"sdio0": "sdio0_grp", "sdio0_cd_grp", "sdio0_mmc_grp" + +"sdio1": "sdio1_data_0_grp", "sdio1_data_1_grp", "sdio1_cd_grp", +"sdio1_led_grp", "sdio1_mmc_grp" + +"can0": "can0_grp" + +"can1": "can1_grp" + +"cam": "cam_led_grp", "cam_0_grp", "cam_1_grp" + +"bsc1": "bsc1_grp" + +"pcie_clkreq": "pcie_clkreq_grp" + +"usb0_oc": "usb0_oc_grp" + +"usb1_oc": "usb1_oc_grp" + +"usb2_oc": "usb2_oc_grp" diff --git a/dts/Bindings/pinctrl/marvell,armada-39x-pinctrl.txt b/dts/Bindings/pinctrl/marvell,armada-39x-pinctrl.txt new file mode 100644 index 0000000000..5b1a9dc004 --- /dev/null +++ b/dts/Bindings/pinctrl/marvell,armada-39x-pinctrl.txt @@ -0,0 +1,78 @@ +* Marvell Armada 39x SoC pinctrl driver for mpp + +Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding +part and usage. + +Required properties: +- compatible: "marvell,88f6920-pinctrl", "marvell,88f6928-pinctrl" + depending on the specific variant of the SoC being used. +- reg: register specifier of MPP registers + +Available mpp pins/groups and functions: +Note: brackets (x) are not part of the mpp name for marvell,function and given +only for more detailed description in this document. + +name pins functions +================================================================================ +mpp0 0 gpio, ua0(rxd) +mpp1 1 gpio, ua0(txd) +mpp2 2 gpio, i2c0(sck) +mpp3 3 gpio, i2c0(sda) +mpp4 4 gpio, ua1(txd), ua0(rts), smi(mdc) +mpp5 5 gpio, ua1(rxd), ua0(cts), smi(mdio) +mpp6 6 gpio, dev(cs3), xsmi(mdio) +mpp7 7 gpio, dev(ad9), xsmi(mdc) +mpp8 8 gpio, dev(ad10), ptp(trig) +mpp9 9 gpio, dev(ad11), ptp(clk) +mpp10 10 gpio, dev(ad12), ptp(event) +mpp11 11 gpio, dev(ad13), led(clk) +mpp12 12 gpio, pcie0(rstout), dev(ad14), led(stb) +mpp13 13 gpio, dev(ad15), led(data) +mpp14 14 gpio, m(vtt), dev(wen1), ua1(txd) +mpp15 15 gpio, pcie0(rstout), spi0(mosi), i2c1(sck) +mpp16 16 gpio, m(decc), spi0(miso), i2c1(sda) +mpp17 17 gpio, ua1(rxd), spi0(sck), smi(mdio) +mpp18 18 gpio, ua1(txd), spi0(cs0), i2c2(sck) +mpp19 19 gpio, sata1(present) [1], ua0(cts), ua1(rxd), i2c2(sda) +mpp20 20 gpio, sata0(present) [1], ua0(rts), ua1(txd), smi(mdc) +mpp21 21 gpio, spi0(cs1), sata0(present) [1], sd(cmd), dev(bootcs), ge(rxd0) +mpp22 22 gpio, spi0(mosi), dev(ad0) +mpp23 23 gpio, spi0(sck), dev(ad2) +mpp24 24 gpio, spi0(miso), ua0(cts), ua1(rxd), sd(d4), dev(readyn) +mpp25 25 gpio, spi0(cs0), ua0(rts), ua1(txd), sd(d5), dev(cs0) +mpp26 26 gpio, spi0(cs2), i2c1(sck), sd(d6), dev(cs1) +mpp27 27 gpio, spi0(cs3), i2c1(sda), sd(d7), dev(cs2), ge(txclkout) +mpp28 28 gpio, sd(clk), dev(ad5), ge(txd0) +mpp29 29 gpio, dev(ale0), ge(txd1) +mpp30 30 gpio, dev(oen), ge(txd2) +mpp31 31 gpio, dev(ale1), ge(txd3) +mpp32 32 gpio, dev(wen0), ge(txctl) +mpp33 33 gpio, m(decc), dev(ad3) +mpp34 34 gpio, dev(ad1) +mpp35 35 gpio, ref(clk), dev(a1) +mpp36 36 gpio, dev(a0) +mpp37 37 gpio, sd(d3), dev(ad8), ge(rxclk) +mpp38 38 gpio, ref(clk), sd(d0), dev(ad4), ge(rxd1) +mpp39 39 gpio, i2c1(sck), ua0(cts), sd(d1), dev(a2), ge(rxd2) +mpp40 40 gpio, i2c1(sda), ua0(rts), sd(d2), dev(ad6), ge(rxd3) +mpp41 41 gpio, ua1(rxd), ua0(cts), spi1(cs3), dev(burstn), nd(rbn0), ge(rxctl) +mpp42 42 gpio, ua1(txd), ua0(rts), dev(ad7) +mpp43 43 gpio, pcie0(clkreq), m(vtt), m(decc), spi1(cs2), dev(clkout), nd(rbn1) +mpp44 44 gpio, sata0(present) [1], sata1(present) [1], led(clk) +mpp45 45 gpio, ref(clk), pcie0(rstout), ua1(rxd) +mpp46 46 gpio, ref(clk), pcie0(rstout), ua1(txd), led(stb) +mpp47 47 gpio, sata0(present) [1], sata1(present) [1], led(data) +mpp48 48 gpio, sata0(present) [1], m(vtt), tdm(pclk) [1], audio(mclk) [1], sd(d4), pcie0(clkreq), ua1(txd) +mpp49 49 gpio, tdm(fsync) [1], audio(lrclk) [1], sd(d5), ua2(rxd) +mpp50 50 gpio, pcie0(rstout), tdm(drx) [1], audio(extclk) [1], sd(cmd), ua2(rxd) +mpp51 51 gpio, tdm(dtx) [1], audio(sdo) [1], m(decc), ua2(txd) +mpp52 52 gpio, pcie0(rstout), tdm(intn) [1], audio(sdi) [1], sd(d6), i2c3(sck) +mpp53 53 gpio, sata1(present) [1], sata0(present) [1], tdm(rstn) [1], audio(bclk) [1], sd(d7), i2c3(sda) +mpp54 54 gpio, sata0(present) [1], sata1(present) [1], pcie0(rstout), sd(d3), ua3(txd) +mpp55 55 gpio, ua1(cts), spi1(cs1), sd(d0), ua1(rxd), ua3(rxd) +mpp56 56 gpio, ua1(rts), m(decc), spi1(mosi), ua1(txd) +mpp57 57 gpio, spi1(sck), sd(clk), ua1(txd) +mpp58 58 gpio, i2c1(sck), pcie2(clkreq), spi1(miso), sd(d1), ua1(rxd) +mpp59 59 gpio, pcie0(rstout), i2c1(sda), spi1(cs0), sd(d2) + +[1]: only available on 88F6928 diff --git a/dts/Bindings/pinctrl/meson,pinctrl.txt b/dts/Bindings/pinctrl/meson,pinctrl.txt index 17e7240c69..3f6a524cc5 100644 --- a/dts/Bindings/pinctrl/meson,pinctrl.txt +++ b/dts/Bindings/pinctrl/meson,pinctrl.txt @@ -1,7 +1,7 @@ == Amlogic Meson pinmux controller == Required properties for the root node: - - compatible: "amlogic,meson8-pinctrl" + - compatible: "amlogic,meson8-pinctrl" or "amlogic,meson8b-pinctrl" - reg: address and size of registers controlling irq functionality === GPIO sub-nodes === diff --git a/dts/Bindings/pinctrl/nvidia,tegra210-pinmux.txt b/dts/Bindings/pinctrl/nvidia,tegra210-pinmux.txt new file mode 100644 index 0000000000..a62d82d5fb --- /dev/null +++ b/dts/Bindings/pinctrl/nvidia,tegra210-pinmux.txt @@ -0,0 +1,166 @@ +NVIDIA Tegra210 pinmux controller + +Required properties: +- compatible: "nvidia,tegra210-pinmux" +- reg: Should contain a list of base address and size pairs for: + - first entry: The APB_MISC_GP_*_PADCTRL registers (pad control) + - second entry: The PINMUX_AUX_* registers (pinmux) + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +Tegra's pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, tristate, drive strength, etc. + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function or tristate parameter. For this +reason, even seemingly boolean values are actually tristates in this binding: +unspecified, off, or on. Unspecified is represented as an absent property, +and off/on are represented as integer values 0 and 1. + +See the TRM to determine which properties and values apply to each pin/group. +Macro values for property values are defined in +include/dt-binding/pinctrl/pinctrl-tegra.h. + +Required subnode-properties: +- nvidia,pins : An array of strings. Each string contains the name of a pin or + group. Valid values for these names are listed below. + +Optional subnode-properties: +- nvidia,function: A string containing the name of the function to mux to the + pin or group. +- nvidia,pull: Integer, representing the pull-down/up to apply to the pin. + 0: none, 1: down, 2: up. +- nvidia,tristate: Integer. + 0: drive, 1: tristate. +- nvidia,enable-input: Integer. Enable the pin's input path. + enable :TEGRA_PIN_ENABLE0 and + disable or output only: TEGRA_PIN_DISABLE. +- nvidia,open-drain: Integer. + enable: TEGRA_PIN_ENABLE. + disable: TEGRA_PIN_DISABLE. +- nvidia,lock: Integer. Lock the pin configuration against further changes + until reset. + enable: TEGRA_PIN_ENABLE. + disable: TEGRA_PIN_DISABLE. +- nvidia,io-hv: Integer. Select high-voltage receivers. + normal: TEGRA_PIN_DISABLE + high: TEGRA_PIN_ENABLE +- nvidia,high-speed-mode: Integer. Enable high speed mode the pins. + normal: TEGRA_PIN_DISABLE + high: TEGRA_PIN_ENABLE +- nvidia,schmitt: Integer. Enables Schmitt Trigger on the input. + normal: TEGRA_PIN_DISABLE + high: TEGRA_PIN_ENABLE +- nvidia,drive-type: Integer. Valid range 0...3. +- nvidia,pull-down-strength: Integer. Controls drive strength. 0 is weakest. + The range of valid values depends on the pingroup. See "CAL_DRVDN" in the + Tegra TRM. +- nvidia,pull-up-strength: Integer. Controls drive strength. 0 is weakest. + The range of valid values depends on the pingroup. See "CAL_DRVUP" in the + Tegra TRM. +- nvidia,slew-rate-rising: Integer. Controls rising signal slew rate. 0 is + fastest. The range of valid values depends on the pingroup. See + "DRVDN_SLWR" in the Tegra TRM. +- nvidia,slew-rate-falling: Integer. Controls falling signal slew rate. 0 is + fastest. The range of valid values depends on the pingroup. See + "DRVUP_SLWF" in the Tegra TRM. + +Valid values for pin and group names (nvidia,pin) are: + + Mux groups: + + These correspond to Tegra PINMUX_AUX_* (pinmux) registers. Any property + that exists in those registers may be set for the following pin names. + + In Tegra210, many pins also have a dedicated APB_MISC_GP_*_PADCTRL + register. Where that is true, and property that exists in that register + may also be set on the following pin names. + + als_prox_int_px3, ap_ready_pv5, ap_wake_bt_ph3, ap_wake_nfc_ph7, + aud_mclk_pbb0, batt_bcl, bt_rst_ph4, bt_wake_ap_ph5, button_home_py1, + button_power_on_px5, button_slide_sw_py0, button_vol_down_px7, + button_vol_up_px6, cam1_mclk_ps0, cam1_pwdn_ps7, cam1_strobe_pt1, + cam2_mclk_ps1, cam2_pwdn_pt0, cam_af_en_ps5, cam_flash_en_ps6, + cam_i2c_scl_ps2, cam_i2c_sda_ps3, cam_rst_ps4cam_rst_ps4, clk_32k_in, + clk_32k_out_py5, clk_req, core_pwr_req, cpu_pwr_req, dap1_din_pb1, + dap1_dout_pb2, dap1_fs_pb0, dap1_sclk_pb3, dap2_din_paa2, dap2_dout_paa3, + dap2_fs_paa0, dap2_sclk_paa1, dap4_din_pj5, dap4_dout_pj6, dap4_fs_pj4, + dap4_sclk_pj7, dmic1_clk_pe0, dmic1_dat_pe1, dmic2_clk_pe2, dmic2_dat_pe3, + dmic3_clk_pe4, dmic3_dat_pe5, dp_hpd0_pcc6, dvfs_clk_pbb2, dvfs_pwm_pbb1, + gen1_i2c_scl_pj1, gen1_i2c_sda_pj0, gen2_i2c_scl_pj2, gen2_i2c_sda_pj3, + gen3_i2c_scl_pf0, gen3_i2c_sda_pf1, gpio_x1_aud_pbb3, gpio_x3_aud_pbb4, + gps_en_pi2, gps_rst_pi3, hdmi_cec_pcc0, hdmi_int_dp_hpd_pcc1, jtag_rtck, + lcd_bl_en_pv1, lcd_bl_pwm_pv0, lcd_gpio1_pv3, lcd_gpio2_pv4, lcd_rst_pv2, + lcd_te_py2, modem_wake_ap_px0, motion_int_px2, nfc_en_pi0, nfc_int_pi1, + pa6, pcc7, pe6, pe7, pex_l0_clkreq_n_pa1, pex_l0_rst_n_pa0, + pex_l1_clkreq_n_pa4, pex_l1_rst_n_pa3, pex_wake_n_pa2, ph6, pk0, pk1, pk2, + pk3, pk4, pk5, pk6, pk7, pl0, pl1, pwr_i2c_scl_py3, pwr_i2c_sda_py4, + pwr_int_n, pz0, pz1, pz2, pz3, pz4, pz5, qspi_cs_n_pee1, qspi_io0_pee2, + qspi_io1_pee3, qspi_io2_pee4, qspi_io3_pee5, qspi_sck_pee0, + sata_led_active_pa5, sdmmc1_clk_pm0, sdmmc1_cmd_pm1, sdmmc1_dat0_pm5, + sdmmc1_dat1_pm4, sdmmc1_dat2_pm3, sdmmc1_dat3_pm2, sdmmc3_clk_pp0, + sdmmc3_cmd_pp1, sdmmc3_dat0_pp5, sdmmc3_dat1_pp4, sdmmc3_dat2_pp3, + sdmmc3_dat3_pp2, shutdown, spdif_in_pcc3, spdif_out_pcc2, spi1_cs0_pc3, + spi1_cs1_pc4, spi1_miso_pc1, spi1_mosi_pc0, spi1_sck_pc2, spi2_cs0_pb7, + spi2_cs1_pdd0, spi2_miso_pb5, spi2_mosi_pb4, spi2_sck_pb6, spi4_cs0_pc6, + spi4_miso_pd0, spi4_mosi_pc7, spi4_sck_pc5, temp_alert_px4, touch_clk_pv7, + touch_int_px1, touch_rst_pv6, uart1_cts_pu3, uart1_rts_pu2, uart1_rx_pu1, + uart1_tx_pu0, uart2_cts_pg3, uart2_rts_pg2, uart2_rx_pg1, uart2_tx_pg0, + uart3_cts_pd4, uart3_rts_pd3, uart3_rx_pd2, uart3_tx_pd1, uart4_cts_pi7, + uart4_rts_pi6, uart4_rx_pi5, uart4_tx_pi4, usb_vbus_en0_pcc4, + usb_vbus_en1_pcc5, wifi_en_ph0, wifi_rst_ph1, wifi_wake_ap_ph2 + + Drive groups: + + These correspond to the Tegra APB_MISC_GP_*_PADCTRL (pad control) + registers. Note that where one of these registers controls a single pin + for which a PINMUX_AUX_* exists, see the list above for the pin name to + use when configuring the pinmux. + + pa6, pcc7, pe6, pe7, ph6, pk0, pk1, pk2, pk3, pk4, pk5, pk6, pk7, pl0, pl1, + pz0, pz1, pz2, pz3, pz4, pz5, sdmmc1, sdmmc2, sdmmc3, sdmmc4 + +Valid values for nvidia,functions are: + + aud, bcl, blink, ccla, cec, cldvfs, clk, core, cpu, displaya, displayb, + dmic1, dmic2, dmic3, dp, dtv, extperiph3, i2c1, i2c2, i2c3, i2cpmu, i2cvi, + i2s1, i2s2, i2s3, i2s4a, i2s4b, i2s5a, i2s5b, iqc0, iqc1, jtag, pe, pe0, + pe1, pmi, pwm0, pwm1, pwm2, pwm3, qspi, rsvd0, rsvd1, rsvd2, rsvd3, sata, + sdmmc1, sdmmc3, shutdown, soc, sor0, sor1, spdif, spi1, spi2, spi3, spi4, + sys, touch, uart, uarta, uartb, uartc, uartd, usb, vgp1, vgp2, vgp3, vgp4, + vgp5, vgp6, vimclk, vimclk2 + +Example: + + pinmux: pinmux@70000800 { + compatible = "nvidia,tegra210-pinmux"; + reg = <0x0 0x700008d4 0x0 0x2a8>, /* Pad control registers */ + <0x0 0x70003000 0x0 0x1000>; /* Mux registers */ + + pinctrl-names = "boot"; + pinctrl-0 = <&state_boot>; + + state_boot: pinmux { + gen1_i2c_scl_pj1 { + nvidia,pins = "gen1_i2c_scl_pj1", + nvidia,function = "i2c1"; + nvidia,pull = <TEGRA_PIN_PULL_NONE>; + nvidia,tristate = <TEGRA_PIN_DISABLE>; + nvidia,enable-input = <TEGRA_PIN_ENABLE>; + nvidia,open-drain = <TEGRA_PIN_ENABLE>; + nvidia,io-hv = <TEGRA_PIN_ENABLE>; + }; + }; + }; +}; diff --git a/dts/Bindings/pinctrl/pinctrl-bindings.txt b/dts/Bindings/pinctrl/pinctrl-bindings.txt index 47d84b6ee9..b73c96d24f 100644 --- a/dts/Bindings/pinctrl/pinctrl-bindings.txt +++ b/dts/Bindings/pinctrl/pinctrl-bindings.txt @@ -38,7 +38,7 @@ property exists to define the pin configuration. Each state may also be assigned a name. When names are used, another property exists to map from those names to the integer IDs. -Each client device's own binding determines the set of states the must be +Each client device's own binding determines the set of states that must be defined in its device tree node, and whether to define the set of state IDs that must be provided, or whether to define the set of state names that must be provided. @@ -133,16 +133,27 @@ pin multiplexing nodes: function - the mux function to select groups - the list of groups to select with this function + (either this or "pins" must be specified) +pins - the list of pins to select with this function (either + this or "groups" must be specified) Example: state_0_node_a { - function = "uart0"; - groups = "u0rxtx", "u0rtscts"; + uart0 { + function = "uart0"; + groups = "u0rxtx", "u0rtscts"; + }; }; state_1_node_a { - function = "spi0"; - groups = "spi0pins"; + spi0 { + function = "spi0"; + groups = "spi0pins"; + }; +}; +state_2_node_a { + function = "i2c0"; + pins = "mfio29", "mfio30"; }; == Generic pin configuration node content == @@ -188,16 +199,22 @@ slew-rate - set the slew rate For example: state_0_node_a { - pins = "GPIO0_AJ5", "GPIO2_AH4"; /* CTS+RXD */ - bias-pull-up; + cts_rxd { + pins = "GPIO0_AJ5", "GPIO2_AH4"; /* CTS+RXD */ + bias-pull-up; + }; }; state_1_node_a { - pins = "GPIO1_AJ3", "GPIO3_AH3"; /* RTS+TXD */ - output-high; + rts_txd { + pins = "GPIO1_AJ3", "GPIO3_AH3"; /* RTS+TXD */ + output-high; + }; }; state_2_node_a { - group = "foo-group"; - bias-pull-up; + foo { + group = "foo-group"; + bias-pull-up; + }; }; Some of the generic properties take arguments. For those that do, the diff --git a/dts/Bindings/pinctrl/pinctrl-mt65xx.txt b/dts/Bindings/pinctrl/pinctrl-mt65xx.txt new file mode 100644 index 0000000000..5868a0f725 --- /dev/null +++ b/dts/Bindings/pinctrl/pinctrl-mt65xx.txt @@ -0,0 +1,145 @@ +* Mediatek MT65XX Pin Controller + +The Mediatek's Pin controller is used to control SoC pins. + +Required properties: +- compatible: value should be either of the following. + (a) "mediatek,mt8135-pinctrl", compatible with mt8135 pinctrl. +- mediatek,pctl-regmap: Should be a phandle of the syscfg node. +- pins-are-numbered: Specify the subnodes are using numbered pinmux to + specify pins. +- gpio-controller : Marks the device node as a gpio controller. +- #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO + binding is used, the amount of cells must be specified as 2. See the below + mentioned gpio binding representation for description of particular cells. + + Eg: <&pio 6 0> + <[phandle of the gpio controller node] + [line number within the gpio controller] + [flags]> + + Values for gpio specifier: + - Line number: is a value between 0 to 202. + - Flags: bit field of flags, as defined in <dt-bindings/gpio/gpio.h>. + Only the following flags are supported: + 0 - GPIO_ACTIVE_HIGH + 1 - GPIO_ACTIVE_LOW +- reg: physicall address base for EINT registers +- interrupt-controller: Marks the device node as an interrupt controller +- #interrupt-cells: Should be two. +- interrupts : The interrupt outputs from the controller. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices. + +Subnode format +A pinctrl node should contain at least one subnodes representing the +pinctrl groups available on the machine. Each subnode will list the +pins it needs, and how they should be configured, with regard to muxer +configuration, pullups, drive strength, input enable/disable and input schmitt. + + node { + pinmux = <PIN_NUMBER_PINMUX>; + GENERIC_PINCONFIG; + }; + +Required properties: +- pinmux: integer array, represents gpio pin number and mux setting. + Supported pin number and mux varies for different SoCs, and are defined + as macros in boot/dts/<soc>-pinfunc.h directly. + +Optional properties: +- GENERIC_PINCONFIG: is the generic pinconfig options to use, bias-disable, + bias-pull-down, bias-pull-up, input-enable, input-disable, output-low, output-high, + input-schmitt-enable, input-schmitt-disable and drive-strength are valid. + + Some special pins have extra pull up strength, there are R0 and R1 pull-up + resistors available, but for user, it's only need to set R1R0 as 00, 01, 10 or 11. + So when config bias-pull-up, it support arguments for those special pins. + Some macros have been defined for this usage, such as MTK_PUPD_SET_R1R0_00. + See dt-bindings/pinctrl/mt65xx.h. + + When config drive-strength, it can support some arguments, such as + MTK_DRIVE_4mA, MTK_DRIVE_6mA, etc. See dt-bindings/pinctrl/mt65xx.h. + +Examples: + +#include "mt8135-pinfunc.h" + +... +{ + syscfg_pctl_a: syscfg_pctl_a@10005000 { + compatible = "mediatek,mt8135-pctl-a-syscfg", "syscon"; + reg = <0 0x10005000 0 0x1000>; + }; + + syscfg_pctl_b: syscfg_pctl_b@1020C020 { + compatible = "mediatek,mt8135-pctl-b-syscfg", "syscon"; + reg = <0 0x1020C020 0 0x1000>; + }; + + pinctrl@01c20800 { + compatible = "mediatek,mt8135-pinctrl"; + reg = <0 0x1000B000 0 0x1000>; + mediatek,pctl-regmap = <&syscfg_pctl_a &syscfg_pctl_b>; + pins-are-numbered; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; + + i2c0_pins_a: i2c0@0 { + pins1 { + pinmux = <MT8135_PIN_100_SDA0__FUNC_SDA0>, + <MT8135_PIN_101_SCL0__FUNC_SCL0>; + bias-disable; + }; + }; + + i2c1_pins_a: i2c1@0 { + pins { + pinmux = <MT8135_PIN_195_SDA1__FUNC_SDA1>, + <MT8135_PIN_196_SCL1__FUNC_SCL1>; + bias-pull-up = <55>; + }; + }; + + i2c2_pins_a: i2c2@0 { + pins1 { + pinmux = <MT8135_PIN_193_SDA2__FUNC_SDA2>; + bias-pull-down; + }; + + pins2 { + pinmux = <MT8135_PIN_49_WATCHDOG__FUNC_GPIO49>; + bias-pull-up; + }; + }; + + i2c3_pins_a: i2c3@0 { + pins1 { + pinmux = <MT8135_PIN_40_DAC_CLK__FUNC_GPIO40>, + <MT8135_PIN_41_DAC_WS__FUNC_GPIO41>; + bias-pull-up = <55>; + }; + + pins2 { + pinmux = <MT8135_PIN_35_SCL3__FUNC_SCL3>, + <MT8135_PIN_36_SDA3__FUNC_SDA3>; + output-low; + bias-pull-up = <55>; + }; + + pins3 { + pinmux = <MT8135_PIN_57_JTCK__FUNC_GPIO57>, + <MT8135_PIN_60_JTDI__FUNC_JTDI>; + drive-strength = <32>; + }; + }; + + ... + } +}; diff --git a/dts/Bindings/pinctrl/qcom,pmic-gpio.txt b/dts/Bindings/pinctrl/qcom,pmic-gpio.txt index 7ed0804851..1ae63c0acd 100644 --- a/dts/Bindings/pinctrl/qcom,pmic-gpio.txt +++ b/dts/Bindings/pinctrl/qcom,pmic-gpio.txt @@ -10,6 +10,7 @@ PMIC's from Qualcomm. "qcom,pm8018-gpio" "qcom,pm8038-gpio" "qcom,pm8058-gpio" + "qcom,pm8916-gpio" "qcom,pm8917-gpio" "qcom,pm8921-gpio" "qcom,pm8941-gpio" @@ -74,6 +75,7 @@ to specify in a pin configuration subnode: gpio1-gpio6 for pm8018 gpio1-gpio12 for pm8038 gpio1-gpio40 for pm8058 + gpio1-gpio4 for pm8916 gpio1-gpio38 for pm8917 gpio1-gpio44 for pm8921 gpio1-gpio36 for pm8941 diff --git a/dts/Bindings/pinctrl/qcom,pmic-mpp.txt b/dts/Bindings/pinctrl/qcom,pmic-mpp.txt index 854774b194..ed19991aad 100644 --- a/dts/Bindings/pinctrl/qcom,pmic-mpp.txt +++ b/dts/Bindings/pinctrl/qcom,pmic-mpp.txt @@ -8,6 +8,7 @@ of PMIC's from Qualcomm. Value type: <string> Definition: Should contain one of: "qcom,pm8841-mpp", + "qcom,pm8916-mpp", "qcom,pm8941-mpp", "qcom,pma8084-mpp", @@ -67,6 +68,7 @@ to specify in a pin configuration subnode: Definition: List of MPP pins affected by the properties specified in this subnode. Valid pins are: mpp1-mpp4 for pm8841 + mpp1-mpp4 for pm8916 mpp1-mpp8 for pm8941 mpp1-mpp4 for pma8084 diff --git a/dts/Bindings/power/da9150-charger.txt b/dts/Bindings/power/da9150-charger.txt new file mode 100644 index 0000000000..f3906663c4 --- /dev/null +++ b/dts/Bindings/power/da9150-charger.txt @@ -0,0 +1,26 @@ +Dialog Semiconductor DA9150 Charger Power Supply bindings + +Required properties: +- compatible: "dlg,da9150-charger" for DA9150 Charger Power Supply + +Optional properties: +- io-channels: List of phandle and IIO specifier pairs +- io-channel-names: List of channel names used by charger + ["CHAN_IBUS", "CHAN_VBUS", "CHAN_TJUNC", "CHAN_VBAT"] + (See Documentation/devicetree/bindings/iio/iio-bindings.txt for further info) + + +Example: + + da9150-charger { + compatible = "dlg,da9150-charger"; + + io-channels = <&gpadc 0>, + <&gpadc 2>, + <&gpadc 8>, + <&gpadc 5>; + io-channel-names = "CHAN_IBUS", + "CHAN_VBUS", + "CHAN_TJUNC", + "CHAN_VBAT"; + }; diff --git a/dts/Bindings/power/fsl,imx-gpc.txt b/dts/Bindings/power/fsl,imx-gpc.txt new file mode 100644 index 0000000000..65cc034574 --- /dev/null +++ b/dts/Bindings/power/fsl,imx-gpc.txt @@ -0,0 +1,59 @@ +Freescale i.MX General Power Controller +======================================= + +The i.MX6Q General Power Control (GPC) block contains DVFS load tracking +counters and Power Gating Control (PGC) for the CPU and PU (GPU/VPU) power +domains. + +Required properties: +- compatible: Should be "fsl,imx6q-gpc" or "fsl,imx6sl-gpc" +- reg: should be register base and length as documented in the + datasheet +- interrupts: Should contain GPC interrupt request 1 +- pu-supply: Link to the LDO regulator powering the PU power domain +- clocks: Clock phandles to devices in the PU power domain that need + to be enabled during domain power-up for reset propagation. +- #power-domain-cells: Should be 1, see below: + +The gpc node is a power-controller as documented by the generic power domain +bindings in Documentation/devicetree/bindings/power/power_domain.txt. + +Example: + + gpc: gpc@020dc000 { + compatible = "fsl,imx6q-gpc"; + reg = <0x020dc000 0x4000>; + interrupts = <0 89 IRQ_TYPE_LEVEL_HIGH>, + <0 90 IRQ_TYPE_LEVEL_HIGH>; + pu-supply = <®_pu>; + clocks = <&clks IMX6QDL_CLK_GPU3D_CORE>, + <&clks IMX6QDL_CLK_GPU3D_SHADER>, + <&clks IMX6QDL_CLK_GPU2D_CORE>, + <&clks IMX6QDL_CLK_GPU2D_AXI>, + <&clks IMX6QDL_CLK_OPENVG_AXI>, + <&clks IMX6QDL_CLK_VPU_AXI>; + #power-domain-cells = <1>; + }; + + +Specifying power domain for IP modules +====================================== + +IP cores belonging to a power domain should contain a 'power-domains' property +that is a phandle pointing to the gpc device node and a DOMAIN_INDEX specifying +the power domain the device belongs to. + +Example of a device that is part of the PU power domain: + + vpu: vpu@02040000 { + reg = <0x02040000 0x3c000>; + /* ... */ + power-domains = <&gpc 1>; + /* ... */ + }; + +The following DOMAIN_INDEX values are valid for i.MX6Q: +ARM_DOMAIN 0 +PU_DOMAIN 1 +The following additional DOMAIN_INDEX value is valid for i.MX6SL: +DISPLAY_DOMAIN 2 diff --git a/dts/Bindings/power/renesas,sysc-rmobile.txt b/dts/Bindings/power/renesas,sysc-rmobile.txt index cc3b1f0a9b..beda7d2efc 100644 --- a/dts/Bindings/power/renesas,sysc-rmobile.txt +++ b/dts/Bindings/power/renesas,sysc-rmobile.txt @@ -11,6 +11,7 @@ Required properties: - compatible: Should be "renesas,sysc-<soctype>", "renesas,sysc-rmobile" as fallback. Examples with soctypes are: + - "renesas,sysc-r8a73a4" (R-Mobile APE6) - "renesas,sysc-r8a7740" (R-Mobile A1) - "renesas,sysc-sh73a0" (SH-Mobile AG5) - reg: Two address start and address range blocks for the device: diff --git a/dts/Bindings/power/reset/syscon-poweroff.txt b/dts/Bindings/power/reset/syscon-poweroff.txt new file mode 100644 index 0000000000..1e2546f8b0 --- /dev/null +++ b/dts/Bindings/power/reset/syscon-poweroff.txt @@ -0,0 +1,23 @@ +Generic SYSCON mapped register poweroff driver + +This is a generic poweroff driver using syscon to map the poweroff register. +The poweroff is generally performed with a write to the poweroff register +defined by the register map pointed by syscon reference plus the offset +with the mask defined in the poweroff node. + +Required properties: +- compatible: should contain "syscon-poweroff" +- regmap: this is phandle to the register map node +- offset: offset in the register map for the poweroff register (in bytes) +- mask: the poweroff value written to the poweroff register (32 bit access) + +Default will be little endian mode, 32 bit access only. + +Examples: + + poweroff { + compatible = "syscon-poweroff"; + regmap = <®mapnode>; + offset = <0x0>; + mask = <0x7a>; + }; diff --git a/dts/Bindings/pwm/bcm-kona-pwm.txt b/dts/Bindings/pwm/brcm,kona-pwm.txt index 8eae9fe784..8eae9fe784 100644 --- a/dts/Bindings/pwm/bcm-kona-pwm.txt +++ b/dts/Bindings/pwm/brcm,kona-pwm.txt diff --git a/dts/Bindings/pwm/imx-pwm.txt b/dts/Bindings/pwm/imx-pwm.txt index b50d7a6d9d..e00c2e9f48 100644 --- a/dts/Bindings/pwm/imx-pwm.txt +++ b/dts/Bindings/pwm/imx-pwm.txt @@ -1,10 +1,17 @@ Freescale i.MX PWM controller Required properties: -- compatible: should be "fsl,<soc>-pwm" +- compatible : should be "fsl,<soc>-pwm" and one of the following + compatible strings: + - "fsl,imx1-pwm" for PWM compatible with the one integrated on i.MX1 + - "fsl,imx27-pwm" for PWM compatible with the one integrated on i.MX27 - reg: physical base address and length of the controller's registers - #pwm-cells: should be 2. See pwm.txt in this directory for a description of the cells format. +- clocks : Clock specifiers for both ipg and per clocks. +- clock-names : Clock names should include both "ipg" and "per" +See the clock consumer binding, + Documentation/devicetree/bindings/clock/clock-bindings.txt - interrupts: The interrupt for the pwm controller Example: @@ -13,5 +20,8 @@ pwm1: pwm@53fb4000 { #pwm-cells = <2>; compatible = "fsl,imx53-pwm", "fsl,imx27-pwm"; reg = <0x53fb4000 0x4000>; + clocks = <&clks IMX5_CLK_PWM1_IPG_GATE>, + <&clks IMX5_CLK_PWM1_HF_GATE>; + clock-names = "ipg", "per"; interrupts = <61>; }; diff --git a/dts/Bindings/regulator/act8865-regulator.txt b/dts/Bindings/regulator/act8865-regulator.txt index dad6358074..e91485d112 100644 --- a/dts/Bindings/regulator/act8865-regulator.txt +++ b/dts/Bindings/regulator/act8865-regulator.txt @@ -2,13 +2,35 @@ ACT88xx regulators ------------------- Required properties: -- compatible: "active-semi,act8846" or "active-semi,act8865" +- compatible: "active-semi,act8846" or "active-semi,act8865" or "active-semi,act8600" - reg: I2C slave address Optional properties: - system-power-controller: Telling whether or not this pmic is controlling the system power. See Documentation/devicetree/bindings/power/power-controller.txt . +Optional input supply properties: +- for act8600: + - vp1-supply: The input supply for DCDC_REG1 + - vp2-supply: The input supply for DCDC_REG2 + - vp3-supply: The input supply for DCDC_REG3 + - inl-supply: The input supply for LDO_REG5, LDO_REG6, LDO_REG7 and LDO_REG8 + SUDCDC_REG4, LDO_REG9 and LDO_REG10 do not have separate supplies. +- for act8846: + - vp1-supply: The input supply for REG1 + - vp2-supply: The input supply for REG2 + - vp3-supply: The input supply for REG3 + - vp4-supply: The input supply for REG4 + - inl1-supply: The input supply for REG5, REG6 and REG7 + - inl2-supply: The input supply for REG8 and LDO_REG9 + - inl3-supply: The input supply for REG10, REG11 and REG12 +- for act8865: + - vp1-supply: The input supply for DCDC_REG1 + - vp2-supply: The input supply for DCDC_REG2 + - vp3-supply: The input supply for DCDC_REG3 + - inl45-supply: The input supply for LDO_REG1 and LDO_REG2 + - inl67-supply: The input supply for LDO_REG3 and LDO_REG4 + Any standard regulator properties can be used to configure the single regulator. The valid names for regulators are: @@ -16,6 +38,9 @@ The valid names for regulators are: REG1, REG2, REG3, REG4, REG5, REG6, REG7, REG8, REG9, REG10, REG11, REG12 - for act8865: DCDC_REG1, DCDC_REG2, DCDC_REG3, LDO_REG1, LDO_REG2, LDO_REG3, LDO_REG4. + - for act8600: + DCDC_REG1, DCDC_REG2, DCDC_REG3, SUDCDC_REG4, LDO_REG5, LDO_REG6, LDO_REG7, + LDO_REG8, LDO_REG9, LDO_REG10, Example: -------- diff --git a/dts/Bindings/arm/bcm/kona-resetmgr.txt b/dts/Bindings/reset/brcm,bcm21664-resetmgr.txt index 93f31ca1ef..93f31ca1ef 100644 --- a/dts/Bindings/arm/bcm/kona-resetmgr.txt +++ b/dts/Bindings/reset/brcm,bcm21664-resetmgr.txt diff --git a/dts/Bindings/rtc/digicolor-rtc.txt b/dts/Bindings/rtc/digicolor-rtc.txt new file mode 100644 index 0000000000..d464986012 --- /dev/null +++ b/dts/Bindings/rtc/digicolor-rtc.txt @@ -0,0 +1,17 @@ +Conexant Digicolor Real Time Clock controller + +This binding currently supports the CX92755 SoC. + +Required properties: +- compatible: should be "cnxt,cx92755-rtc" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: rtc alarm interrupt + +Example: + + rtc@f0000c30 { + compatible = "cnxt,cx92755-rtc"; + reg = <0xf0000c30 0x18>; + interrupts = <25>; + }; diff --git a/dts/Bindings/rtc/stmp3xxx-rtc.txt b/dts/Bindings/rtc/stmp3xxx-rtc.txt index b800070fe6..fa6a942266 100644 --- a/dts/Bindings/rtc/stmp3xxx-rtc.txt +++ b/dts/Bindings/rtc/stmp3xxx-rtc.txt @@ -7,6 +7,11 @@ Required properties: region. - interrupts: rtc alarm interrupt +Optional properties: +- stmp,crystal-freq: override crystal frequency as determined from fuse bits. + Only <32000> and <32768> are possible for the hardware. Use <0> for + "no crystal". + Example: rtc@80056000 { diff --git a/dts/Bindings/security/tpm/st33zp24-spi.txt b/dts/Bindings/security/tpm/st33zp24-spi.txt new file mode 100644 index 0000000000..158b0165e0 --- /dev/null +++ b/dts/Bindings/security/tpm/st33zp24-spi.txt @@ -0,0 +1,34 @@ +* STMicroelectronics SAS. ST33ZP24 TPM SoC + +Required properties: +- compatible: Should be "st,st33zp24-spi". +- spi-max-frequency: Maximum SPI frequency (<= 10000000). + +Optional ST33ZP24 Properties: +- interrupt-parent: phandle for the interrupt gpio controller +- interrupts: GPIO interrupt to which the chip is connected +- lpcpd-gpios: Output GPIO pin used for ST33ZP24 power management D1/D2 state. +If set, power must be present when the platform is going into sleep/hibernate mode. + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. + +Example (for ARM-based BeagleBoard xM with ST33ZP24 on SPI4): + +&mcspi4 { + + status = "okay"; + + st33zp24@0 { + + compatible = "st,st33zp24-spi"; + + spi-max-frequency = <10000000>; + + interrupt-parent = <&gpio5>; + interrupts = <7 IRQ_TYPE_LEVEL_HIGH>; + + lpcpd-gpios = <&gpio5 15 GPIO_ACTIVE_HIGH>; + }; +}; diff --git a/dts/Bindings/serial/atmel-usart.txt b/dts/Bindings/serial/atmel-usart.txt index a6391e70a8..90787aa2e6 100644 --- a/dts/Bindings/serial/atmel-usart.txt +++ b/dts/Bindings/serial/atmel-usart.txt @@ -1,9 +1,10 @@ * Atmel Universal Synchronous Asynchronous Receiver/Transmitter (USART) Required properties: -- compatible: Should be "atmel,<chip>-usart" +- compatible: Should be "atmel,<chip>-usart" or "atmel,<chip>-dbgu" The compatible <chip> indicated will be the first SoC to support an additional mode or an USART new feature. + For the dbgu UART, use "atmel,<chip>-dbgu", "atmel,<chip>-usart" - reg: Should contain registers location and length - interrupts: Should contain interrupt - clock-names: tuple listing input clock names. diff --git a/dts/Bindings/serial/bcm63xx-uart.txt b/dts/Bindings/serial/brcm,bcm6345-uart.txt index 5c52e5eef1..5c52e5eef1 100644 --- a/dts/Bindings/serial/bcm63xx-uart.txt +++ b/dts/Bindings/serial/brcm,bcm6345-uart.txt diff --git a/dts/Bindings/serial/omap_serial.txt b/dts/Bindings/serial/omap_serial.txt index 342eedd100..54c2a155c7 100644 --- a/dts/Bindings/serial/omap_serial.txt +++ b/dts/Bindings/serial/omap_serial.txt @@ -4,7 +4,27 @@ Required properties: - compatible : should be "ti,omap2-uart" for OMAP2 controllers - compatible : should be "ti,omap3-uart" for OMAP3 controllers - compatible : should be "ti,omap4-uart" for OMAP4 controllers +- reg : address and length of the register space +- interrupts or interrupts-extended : Should contain the uart interrupt + specifier or both the interrupt + controller phandle and interrupt + specifier. - ti,hwmods : Must be "uart<n>", n being the instance number (1-based) Optional properties: - clock-frequency : frequency of the clock input to the UART +- dmas : DMA specifier, consisting of a phandle to the DMA controller + node and a DMA channel number. +- dma-names : "rx" for receive channel, "tx" for transmit channel. + +Example: + + uart4: serial@49042000 { + compatible = "ti,omap3-uart"; + reg = <0x49042000 0x400>; + interrupts = <80>; + dmas = <&sdma 81 &sdma 82>; + dma-names = "tx", "rx"; + ti,hwmods = "uart4"; + clock-frequency = <48000000>; + }; diff --git a/dts/Bindings/soc/mediatek/pwrap.txt b/dts/Bindings/soc/mediatek/pwrap.txt new file mode 100644 index 0000000000..ddeb5b6a53 --- /dev/null +++ b/dts/Bindings/soc/mediatek/pwrap.txt @@ -0,0 +1,58 @@ +MediaTek PMIC Wrapper Driver + +This document describes the binding for the MediaTek PMIC wrapper. + +On MediaTek SoCs the PMIC is connected via SPI. The SPI master interface +is not directly visible to the CPU, but only through the PMIC wrapper +inside the SoC. The communication between the SoC and the PMIC can +optionally be encrypted. Also a non standard Dual IO SPI mode can be +used to increase speed. + +IP Pairing + +on MT8135 the pins of some SoC internal peripherals can be on the PMIC. +The signals of these pins are routed over the SPI bus using the pwrap +bridge. In the binding description below the properties needed for bridging +are marked with "IP Pairing". These are optional on SoCs which do not support +IP Pairing + +Required properties in pwrap device node. +- compatible: + "mediatek,mt8135-pwrap" for MT8135 SoCs + "mediatek,mt8173-pwrap" for MT8173 SoCs +- interrupts: IRQ for pwrap in SOC +- reg-names: Must include the following entries: + "pwrap": Main registers base + "pwrap-bridge": bridge base (IP Pairing) +- reg: Must contain an entry for each entry in reg-names. +- reset-names: Must include the following entries: + "pwrap" + "pwrap-bridge" (IP Pairing) +- resets: Must contain an entry for each entry in reset-names. +- clock-names: Must include the following entries: + "spi": SPI bus clock + "wrap": Main module clock +- clocks: Must contain an entry for each entry in clock-names. + +Optional properities: +- pmic: Mediatek PMIC MFD is the child device of pwrap + See the following for child node definitions: + Documentation/devicetree/bindings/mfd/mt6397.txt + +Example: + pwrap: pwrap@1000f000 { + compatible = "mediatek,mt8135-pwrap"; + reg = <0 0x1000f000 0 0x1000>, + <0 0x11017000 0 0x1000>; + reg-names = "pwrap", "pwrap-bridge"; + interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>; + resets = <&infracfg MT8135_INFRA_PMIC_WRAP_RST>, + <&pericfg MT8135_PERI_PWRAP_BRIDGE_SW_RST>; + reset-names = "pwrap", "pwrap-bridge"; + clocks = <&clk26m>, <&clk26m>; + clock-names = "spi", "wrap"; + + pmic { + compatible = "mediatek,mt6397"; + }; + }; diff --git a/dts/Bindings/soc/qcom/qcom,gsbi.txt b/dts/Bindings/soc/qcom/qcom,gsbi.txt index 4ce24d425b..2f5ede39be 100644 --- a/dts/Bindings/soc/qcom/qcom,gsbi.txt +++ b/dts/Bindings/soc/qcom/qcom,gsbi.txt @@ -6,7 +6,8 @@ configuration settings. The mode setting will govern the input/output mode of the 4 GSBI IOs. Required properties: -- compatible: must contain "qcom,gsbi-v1.0.0" for APQ8064/IPQ8064 +- compatible: Should contain "qcom,gsbi-v1.0.0" +- cell-index: Should contain the GSBI index - reg: Address range for GSBI registers - clocks: required clock - clock-names: must contain "iface" entry @@ -16,6 +17,8 @@ Required properties: Optional properties: - qcom,crci : indicates CRCI MUX value for QUP CRCI ports. Please reference dt-bindings/soc/qcom,gsbi.h for valid CRCI mux values. +- syscon-tcsr: indicates phandle of TCSR syscon node. Required if child uses + dma. Required properties if child node exists: - #address-cells: Must be 1 @@ -39,6 +42,7 @@ Example for APQ8064: gsbi4@16300000 { compatible = "qcom,gsbi-v1.0.0"; + cell-index = <4>; reg = <0x16300000 0x100>; clocks = <&gcc GSBI4_H_CLK>; clock-names = "iface"; @@ -48,22 +52,24 @@ Example for APQ8064: qcom,mode = <GSBI_PROT_I2C_UART>; qcom,crci = <GSBI_CRCI_QUP>; + syscon-tcsr = <&tcsr>; + /* child nodes go under here */ i2c_qup4: i2c@16380000 { - compatible = "qcom,i2c-qup-v1.1.1"; - reg = <0x16380000 0x1000>; - interrupts = <0 153 0>; + compatible = "qcom,i2c-qup-v1.1.1"; + reg = <0x16380000 0x1000>; + interrupts = <0 153 0>; - clocks = <&gcc GSBI4_QUP_CLK>, <&gcc GSBI4_H_CLK>; - clock-names = "core", "iface"; + clocks = <&gcc GSBI4_QUP_CLK>, <&gcc GSBI4_H_CLK>; + clock-names = "core", "iface"; - clock-frequency = <200000>; + clock-frequency = <200000>; - #address-cells = <1>; - #size-cells = <0>; + #address-cells = <1>; + #size-cells = <0>; - }; + }; uart4: serial@16340000 { compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; @@ -76,3 +82,7 @@ Example for APQ8064: }; }; + tcsr: syscon@1a400000 { + compatible = "qcom,apq8064-tcsr", "syscon"; + reg = <0x1a400000 0x100>; + }; diff --git a/dts/Bindings/sound/bcm2835-i2s.txt b/dts/Bindings/sound/brcm,bcm2835-i2s.txt index 65783de0ae..65783de0ae 100644 --- a/dts/Bindings/sound/bcm2835-i2s.txt +++ b/dts/Bindings/sound/brcm,bcm2835-i2s.txt diff --git a/dts/Bindings/sound/ingenic,jz4740-i2s.txt b/dts/Bindings/sound/ingenic,jz4740-i2s.txt index b41433386e..b623d50004 100644 --- a/dts/Bindings/sound/ingenic,jz4740-i2s.txt +++ b/dts/Bindings/sound/ingenic,jz4740-i2s.txt @@ -1,7 +1,7 @@ Ingenic JZ4740 I2S controller Required properties: -- compatible : "ingenic,jz4740-i2s" +- compatible : "ingenic,jz4740-i2s" or "ingenic,jz4780-i2s" - reg : I2S registers location and length - clocks : AIC and I2S PLL clock specifiers. - clock-names: "aic" and "i2s" diff --git a/dts/Bindings/sound/max98925.txt b/dts/Bindings/sound/max98925.txt new file mode 100644 index 0000000000..27be63e2aa --- /dev/null +++ b/dts/Bindings/sound/max98925.txt @@ -0,0 +1,22 @@ +max98925 audio CODEC + +This device supports I2C. + +Required properties: + + - compatible : "maxim,max98925" + + - vmon-slot-no : slot number used to send voltage information + + - imon-slot-no : slot number used to send current information + + - reg : the I2C address of the device for I2C + +Example: + +codec: max98925@1a { + compatible = "maxim,max98925"; + vmon-slot-no = <0>; + imon-slot-no = <2>; + reg = <0x1a>; +}; diff --git a/dts/Bindings/sound/nvidia,tegra-audio-max98090.txt b/dts/Bindings/sound/nvidia,tegra-audio-max98090.txt index c949abc299..c3495beba3 100644 --- a/dts/Bindings/sound/nvidia,tegra-audio-max98090.txt +++ b/dts/Bindings/sound/nvidia,tegra-audio-max98090.txt @@ -18,6 +18,7 @@ Required properties: * Headphones * Speakers * Mic Jack + * Int Mic - nvidia,i2s-controller : The phandle of the Tegra I2S controller that's connected to the CODEC. diff --git a/dts/Bindings/sound/omap-twl4030.txt b/dts/Bindings/sound/omap-twl4030.txt index 1ab6bc8404..f6a715e4ef 100644 --- a/dts/Bindings/sound/omap-twl4030.txt +++ b/dts/Bindings/sound/omap-twl4030.txt @@ -4,9 +4,9 @@ Required properties: - compatible: "ti,omap-twl4030" - ti,model: Name of the sound card (for example "omap3beagle") - ti,mcbsp: phandle for the McBSP node -- ti,codec: phandle for the twl4030 audio node Optional properties: +- ti,codec: phandle for the twl4030 audio node - ti,mcbsp-voice: phandle for the McBSP node connected to the voice port of twl - ti, jack-det-gpio: Jack detect GPIO - ti,audio-routing: List of connections between audio components. @@ -59,5 +59,4 @@ sound { ti,model = "omap3beagle"; ti,mcbsp = <&mcbsp2>; - ti,codec = <&twl_audio>; }; diff --git a/dts/Bindings/sound/qcom,lpass-cpu.txt b/dts/Bindings/sound/qcom,lpass-cpu.txt new file mode 100644 index 0000000000..e00732dac9 --- /dev/null +++ b/dts/Bindings/sound/qcom,lpass-cpu.txt @@ -0,0 +1,43 @@ +* Qualcomm Technologies LPASS CPU DAI + +This node models the Qualcomm Technologies Low-Power Audio SubSystem (LPASS). + +Required properties: + +- compatible : "qcom,lpass-cpu" +- clocks : Must contain an entry for each entry in clock-names. +- clock-names : A list which must include the following entries: + * "ahbix-clk" + * "mi2s-osr-clk" + * "mi2s-bit-clk" +- interrupts : Must contain an entry for each entry in + interrupt-names. +- interrupt-names : A list which must include the following entries: + * "lpass-irq-lpaif" +- pinctrl-N : One property must exist for each entry in + pinctrl-names. See ../pinctrl/pinctrl-bindings.txt + for details of the property values. +- pinctrl-names : Must contain a "default" entry. +- reg : Must contain an address for each entry in reg-names. +- reg-names : A list which must include the following entries: + * "lpass-lpaif" + +Optional properties: + +- qcom,adsp : Phandle for the audio DSP node + +Example: + +lpass@28100000 { + compatible = "qcom,lpass-cpu"; + clocks = <&lcc AHBIX_CLK>, <&lcc MI2S_OSR_CLK>, <&lcc MI2S_BIT_CLK>; + clock-names = "ahbix-clk", "mi2s-osr-clk", "mi2s-bit-clk"; + interrupts = <0 85 1>; + interrupt-names = "lpass-irq-lpaif"; + pinctrl-names = "default", "idle"; + pinctrl-0 = <&mi2s_default>; + pinctrl-1 = <&mi2s_idle>; + reg = <0x28100000 0x10000>; + reg-names = "lpass-lpaif"; + qcom,adsp = <&adsp>; +}; diff --git a/dts/Bindings/sound/renesas,rsnd.txt b/dts/Bindings/sound/renesas,rsnd.txt index 2dd690bc19..f316ce1f21 100644 --- a/dts/Bindings/sound/renesas,rsnd.txt +++ b/dts/Bindings/sound/renesas,rsnd.txt @@ -29,9 +29,17 @@ SSI subnode properties: - shared-pin : if shared clock pin - pio-transfer : use PIO transfer mode - no-busif : BUSIF is not ussed when [mem -> SSI] via DMA case +- dma : Should contain Audio DMAC entry +- dma-names : SSI case "rx" (=playback), "tx" (=capture) + SSIU case "rxu" (=playback), "txu" (=capture) SRC subnode properties: -no properties at this point +- dma : Should contain Audio DMAC entry +- dma-names : "rx" (=playback), "tx" (=capture) + +DVC subnode properties: +- dma : Should contain Audio DMAC entry +- dma-names : "tx" (=playback/capture) DAI subnode properties: - playback : list of playback modules @@ -45,56 +53,145 @@ rcar_sound: rcar_sound@ec500000 { reg = <0 0xec500000 0 0x1000>, /* SCU */ <0 0xec5a0000 0 0x100>, /* ADG */ <0 0xec540000 0 0x1000>, /* SSIU */ - <0 0xec541000 0 0x1280>; /* SSI */ + <0 0xec541000 0 0x1280>, /* SSI */ + <0 0xec740000 0 0x200>; /* Audio DMAC peri peri*/ + reg-names = "scu", "adg", "ssiu", "ssi", "audmapp"; + + clocks = <&mstp10_clks R8A7790_CLK_SSI_ALL>, + <&mstp10_clks R8A7790_CLK_SSI9>, <&mstp10_clks R8A7790_CLK_SSI8>, + <&mstp10_clks R8A7790_CLK_SSI7>, <&mstp10_clks R8A7790_CLK_SSI6>, + <&mstp10_clks R8A7790_CLK_SSI5>, <&mstp10_clks R8A7790_CLK_SSI4>, + <&mstp10_clks R8A7790_CLK_SSI3>, <&mstp10_clks R8A7790_CLK_SSI2>, + <&mstp10_clks R8A7790_CLK_SSI1>, <&mstp10_clks R8A7790_CLK_SSI0>, + <&mstp10_clks R8A7790_CLK_SCU_SRC9>, <&mstp10_clks R8A7790_CLK_SCU_SRC8>, + <&mstp10_clks R8A7790_CLK_SCU_SRC7>, <&mstp10_clks R8A7790_CLK_SCU_SRC6>, + <&mstp10_clks R8A7790_CLK_SCU_SRC5>, <&mstp10_clks R8A7790_CLK_SCU_SRC4>, + <&mstp10_clks R8A7790_CLK_SCU_SRC3>, <&mstp10_clks R8A7790_CLK_SCU_SRC2>, + <&mstp10_clks R8A7790_CLK_SCU_SRC1>, <&mstp10_clks R8A7790_CLK_SCU_SRC0>, + <&mstp10_clks R8A7790_CLK_SCU_DVC0>, <&mstp10_clks R8A7790_CLK_SCU_DVC1>, + <&audio_clk_a>, <&audio_clk_b>, <&audio_clk_c>, <&m2_clk>; + clock-names = "ssi-all", + "ssi.9", "ssi.8", "ssi.7", "ssi.6", "ssi.5", + "ssi.4", "ssi.3", "ssi.2", "ssi.1", "ssi.0", + "src.9", "src.8", "src.7", "src.6", "src.5", + "src.4", "src.3", "src.2", "src.1", "src.0", + "dvc.0", "dvc.1", + "clk_a", "clk_b", "clk_c", "clk_i"; rcar_sound,dvc { - dvc0: dvc@0 { }; - dvc1: dvc@1 { }; + dvc0: dvc@0 { + dmas = <&audma0 0xbc>; + dma-names = "tx"; + }; + dvc1: dvc@1 { + dmas = <&audma0 0xbe>; + dma-names = "tx"; + }; }; rcar_sound,src { - src0: src@0 { }; - src1: src@1 { }; - src2: src@2 { }; - src3: src@3 { }; - src4: src@4 { }; - src5: src@5 { }; - src6: src@6 { }; - src7: src@7 { }; - src8: src@8 { }; - src9: src@9 { }; + src0: src@0 { + interrupts = <0 352 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x85>, <&audma1 0x9a>; + dma-names = "rx", "tx"; + }; + src1: src@1 { + interrupts = <0 353 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x87>, <&audma1 0x9c>; + dma-names = "rx", "tx"; + }; + src2: src@2 { + interrupts = <0 354 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x89>, <&audma1 0x9e>; + dma-names = "rx", "tx"; + }; + src3: src@3 { + interrupts = <0 355 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x8b>, <&audma1 0xa0>; + dma-names = "rx", "tx"; + }; + src4: src@4 { + interrupts = <0 356 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x8d>, <&audma1 0xb0>; + dma-names = "rx", "tx"; + }; + src5: src@5 { + interrupts = <0 357 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x8f>, <&audma1 0xb2>; + dma-names = "rx", "tx"; + }; + src6: src@6 { + interrupts = <0 358 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x91>, <&audma1 0xb4>; + dma-names = "rx", "tx"; + }; + src7: src@7 { + interrupts = <0 359 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x93>, <&audma1 0xb6>; + dma-names = "rx", "tx"; + }; + src8: src@8 { + interrupts = <0 360 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x95>, <&audma1 0xb8>; + dma-names = "rx", "tx"; + }; + src9: src@9 { + interrupts = <0 361 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x97>, <&audma1 0xba>; + dma-names = "rx", "tx"; + }; }; rcar_sound,ssi { ssi0: ssi@0 { interrupts = <0 370 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x01>, <&audma1 0x02>, <&audma0 0x15>, <&audma1 0x16>; + dma-names = "rx", "tx", "rxu", "txu"; }; ssi1: ssi@1 { interrupts = <0 371 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x03>, <&audma1 0x04>, <&audma0 0x49>, <&audma1 0x4a>; + dma-names = "rx", "tx", "rxu", "txu"; }; ssi2: ssi@2 { interrupts = <0 372 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x05>, <&audma1 0x06>, <&audma0 0x63>, <&audma1 0x64>; + dma-names = "rx", "tx", "rxu", "txu"; }; ssi3: ssi@3 { interrupts = <0 373 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x07>, <&audma1 0x08>, <&audma0 0x6f>, <&audma1 0x70>; + dma-names = "rx", "tx", "rxu", "txu"; }; ssi4: ssi@4 { interrupts = <0 374 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x09>, <&audma1 0x0a>, <&audma0 0x71>, <&audma1 0x72>; + dma-names = "rx", "tx", "rxu", "txu"; }; ssi5: ssi@5 { interrupts = <0 375 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x0b>, <&audma1 0x0c>, <&audma0 0x73>, <&audma1 0x74>; + dma-names = "rx", "tx", "rxu", "txu"; }; ssi6: ssi@6 { interrupts = <0 376 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x0d>, <&audma1 0x0e>, <&audma0 0x75>, <&audma1 0x76>; + dma-names = "rx", "tx", "rxu", "txu"; }; ssi7: ssi@7 { interrupts = <0 377 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x0f>, <&audma1 0x10>, <&audma0 0x79>, <&audma1 0x7a>; + dma-names = "rx", "tx", "rxu", "txu"; }; ssi8: ssi@8 { interrupts = <0 378 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x11>, <&audma1 0x12>, <&audma0 0x7b>, <&audma1 0x7c>; + dma-names = "rx", "tx", "rxu", "txu"; }; ssi9: ssi@9 { interrupts = <0 379 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x13>, <&audma1 0x14>, <&audma0 0x7d>, <&audma1 0x7e>; + dma-names = "rx", "tx", "rxu", "txu"; }; }; diff --git a/dts/Bindings/sound/renesas,rsrc-card.txt b/dts/Bindings/sound/renesas,rsrc-card.txt new file mode 100644 index 0000000000..c641550272 --- /dev/null +++ b/dts/Bindings/sound/renesas,rsrc-card.txt @@ -0,0 +1,67 @@ +Renesas Sampling Rate Convert Sound Card: + +Renesas Sampling Rate Convert Sound Card specifies audio DAI connections of SoC <-> codec. + +Required properties: + +- compatible : "renesas,rsrc-card,<board>" + Examples with soctypes are: + - "renesas,rsrc-card,lager" + - "renesas,rsrc-card,koelsch" +Optional properties: + +- card_name : User specified audio sound card name, one string + property. +- cpu : CPU sub-node +- codec : CODEC sub-node + +Optional subnode properties: + +- format : CPU/CODEC common audio format. + "i2s", "right_j", "left_j" , "dsp_a" + "dsp_b", "ac97", "pdm", "msb", "lsb" +- frame-master : Indicates dai-link frame master. + phandle to a cpu or codec subnode. +- bitclock-master : Indicates dai-link bit clock master. + phandle to a cpu or codec subnode. +- bitclock-inversion : bool property. Add this if the + dai-link uses bit clock inversion. +- frame-inversion : bool property. Add this if the + dai-link uses frame clock inversion. +- convert-rate : platform specified sampling rate convert + +Required CPU/CODEC subnodes properties: + +- sound-dai : phandle and port of CPU/CODEC + +Optional CPU/CODEC subnodes properties: + +- clocks / system-clock-frequency : specify subnode's clock if needed. + it can be specified via "clocks" if system has + clock node (= common clock), or "system-clock-frequency" + (if system doens't support common clock) + If a clock is specified, it is + enabled with clk_prepare_enable() + in dai startup() and disabled with + clk_disable_unprepare() in dai + shutdown(). + +Example + +sound { + compatible = "renesas,rsrc-card,lager"; + + card-name = "rsnd-ak4643"; + format = "left_j"; + bitclock-master = <&sndcodec>; + frame-master = <&sndcodec>; + + sndcpu: cpu { + sound-dai = <&rcar_sound>; + }; + + sndcodec: codec { + sound-dai = <&ak4643>; + system-clock-frequency = <11289600>; + }; +}; diff --git a/dts/Bindings/sound/storm.txt b/dts/Bindings/sound/storm.txt new file mode 100644 index 0000000000..062a4c185f --- /dev/null +++ b/dts/Bindings/sound/storm.txt @@ -0,0 +1,23 @@ +* Sound complex for Storm boards + +Models a soundcard for Storm boards with the Qualcomm Technologies IPQ806x SOC +connected to a MAX98357A DAC via I2S. + +Required properties: + +- compatible : "google,storm-audio" +- cpu : Phandle of the CPU DAI +- codec : Phandle of the codec DAI + +Optional properties: + +- qcom,model : The user-visible name of this sound card. + +Example: + +sound { + compatible = "google,storm-audio"; + qcom,model = "ipq806x-storm"; + cpu = <&lpass_cpu>; + codec = <&max98357a>; +}; diff --git a/dts/Bindings/sound/wm8804.txt b/dts/Bindings/sound/wm8804.txt index 4d3a56f38a..6fd124b164 100644 --- a/dts/Bindings/sound/wm8804.txt +++ b/dts/Bindings/sound/wm8804.txt @@ -10,6 +10,13 @@ Required properties: - reg : the I2C address of the device for I2C, the chip select number for SPI. + - PVDD-supply, DVDD-supply : Power supplies for the device, as covered + in Documentation/devicetree/bindings/regulator/regulator.txt + +Optional properties: + + - wlf,reset-gpio: A GPIO specifier for the GPIO controlling the reset pin + Example: codec: wm8804@1a { diff --git a/dts/Bindings/spi/fsl-imx-cspi.txt b/dts/Bindings/spi/fsl-imx-cspi.txt index aad527b357..523341a0e1 100644 --- a/dts/Bindings/spi/fsl-imx-cspi.txt +++ b/dts/Bindings/spi/fsl-imx-cspi.txt @@ -2,11 +2,21 @@ (CSPI/eCSPI) for i.MX Required properties: -- compatible : Should be "fsl,<soc>-cspi" or "fsl,<soc>-ecspi" +- compatible : + - "fsl,imx1-cspi" for SPI compatible with the one integrated on i.MX1 + - "fsl,imx21-cspi" for SPI compatible with the one integrated on i.MX21 + - "fsl,imx27-cspi" for SPI compatible with the one integrated on i.MX27 + - "fsl,imx31-cspi" for SPI compatible with the one integrated on i.MX31 + - "fsl,imx35-cspi" for SPI compatible with the one integrated on i.MX35 + - "fsl,imx51-ecspi" for SPI compatible with the one integrated on i.MX51 - reg : Offset and length of the register set for the device - interrupts : Should contain CSPI/eCSPI interrupt - fsl,spi-num-chipselects : Contains the number of the chipselect - cs-gpios : Specifies the gpio pins to be used for chipselects. +- clocks : Clock specifiers for both ipg and per clocks. +- clock-names : Clock names should include both "ipg" and "per" +See the clock consumer binding, + Documentation/devicetree/bindings/clock/clock-bindings.txt - dmas: DMA specifiers for tx and rx dma. See the DMA client binding, Documentation/devicetree/bindings/dma/dma.txt - dma-names: DMA request names should include "tx" and "rx" if present. diff --git a/dts/Bindings/spi/qcom,spi-qup.txt b/dts/Bindings/spi/qcom,spi-qup.txt index e2c88df2cc..5c090771c0 100644 --- a/dts/Bindings/spi/qcom,spi-qup.txt +++ b/dts/Bindings/spi/qcom,spi-qup.txt @@ -33,6 +33,11 @@ Optional properties: nodes. If unspecified, a single SPI device without a chip select can be used. +- dmas: Two DMA channel specifiers following the convention outlined + in bindings/dma/dma.txt +- dma-names: Names for the dma channels, if present. There must be at + least one channel named "tx" for transmit and named "rx" for + receive. SPI slave nodes must be children of the SPI master node and can contain properties described in Documentation/devicetree/bindings/spi/spi-bus.txt @@ -51,6 +56,9 @@ Example: clocks = <&gcc GCC_BLSP2_QUP2_SPI_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>; clock-names = "core", "iface"; + dmas = <&blsp1_bam 13>, <&blsp1_bam 12>; + dma-names = "rx", "tx"; + pinctrl-names = "default"; pinctrl-0 = <&spi8_default>; diff --git a/dts/Bindings/spi/spi-fsl-dspi.txt b/dts/Bindings/spi/spi-fsl-dspi.txt index cbbe16ed38..70af78a918 100644 --- a/dts/Bindings/spi/spi-fsl-dspi.txt +++ b/dts/Bindings/spi/spi-fsl-dspi.txt @@ -16,6 +16,12 @@ Optional property: in big endian mode, otherwise in native mode(same with CPU), for more detail please see: Documentation/devicetree/bindings/regmap/regmap.txt. +Optional SPI slave node properties: +- fsl,spi-cs-sck-delay: a delay in nanoseconds between activating chip + select and the start of clock signal, at the start of a transfer. +- fsl,spi-sck-cs-delay: a delay in nanoseconds between stopping the clock + signal and deactivating chip select, at the end of a transfer. + Example: dspi0@4002c000 { @@ -43,6 +49,8 @@ dspi0@4002c000 { reg = <0>; linux,modalias = "m25p80"; modal = "at26df081a"; + fsl,spi-cs-sck-delay = <100>; + fsl,spi-sck-cs-delay = <50>; }; }; diff --git a/dts/Bindings/spi/spi-img-spfi.txt b/dts/Bindings/spi/spi-img-spfi.txt index c7dd50fb8e..e02fbf18c8 100644 --- a/dts/Bindings/spi/spi-img-spfi.txt +++ b/dts/Bindings/spi/spi-img-spfi.txt @@ -14,6 +14,7 @@ Required properties: - dma-names: Must include the following entries: - rx - tx +- cs-gpios: Must specify the GPIOs used for chipselect lines. - #address-cells: Must be 1. - #size-cells: Must be 0. diff --git a/dts/Bindings/spi/spi-rockchip.txt b/dts/Bindings/spi/spi-rockchip.txt index 467dec441c..0c491bda4c 100644 --- a/dts/Bindings/spi/spi-rockchip.txt +++ b/dts/Bindings/spi/spi-rockchip.txt @@ -24,6 +24,9 @@ Optional Properties: - dmas: DMA specifiers for tx and rx dma. See the DMA client binding, Documentation/devicetree/bindings/dma/dma.txt - dma-names: DMA request names should include "tx" and "rx" if present. +- rx-sample-delay-ns: nanoseconds to delay after the SCLK edge before sampling + Rx data (may need to be fine tuned for high capacitance lines). + No delay (0) by default. Example: @@ -33,6 +36,7 @@ Example: reg = <0xff110000 0x1000>; dmas = <&pdma1 11>, <&pdma1 12>; dma-names = "tx", "rx"; + rx-sample-delay-ns = <10>; #address-cells = <1>; #size-cells = <0>; interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; diff --git a/dts/Bindings/spmi/qcom,spmi-pmic-arb.txt b/dts/Bindings/spmi/qcom,spmi-pmic-arb.txt index 715d0998af..e16b9b5afc 100644 --- a/dts/Bindings/spmi/qcom,spmi-pmic-arb.txt +++ b/dts/Bindings/spmi/qcom,spmi-pmic-arb.txt @@ -1,6 +1,6 @@ Qualcomm SPMI Controller (PMIC Arbiter) -The SPMI PMIC Arbiter is found on the Snapdragon 800 Series. It is an SPMI +The SPMI PMIC Arbiter is found on Snapdragon chipsets. It is an SPMI controller with wrapping arbitration logic to allow for multiple on-chip devices to control a single SPMI master. @@ -19,6 +19,10 @@ Required properties: "core" - core registers "intr" - interrupt controller registers "cnfg" - configuration registers + Registers used only for V2 PMIC Arbiter: + "chnls" - tx-channel per virtual slave registers. + "obsrvr" - rx-channel (called observer) per virtual slave registers. + - reg : address + size pairs describing the PMIC arb register sets; order must correspond with the order of entries in reg-names - #address-cells : must be set to 2 diff --git a/dts/Bindings/arm/bcm/kona-timer.txt b/dts/Bindings/timer/brcm,kona-timer.txt index 39adf54b43..39adf54b43 100644 --- a/dts/Bindings/arm/bcm/kona-timer.txt +++ b/dts/Bindings/timer/brcm,kona-timer.txt diff --git a/dts/Bindings/unittest.txt b/dts/Bindings/unittest.txt index 8933211f32..3bf58c20fe 100644 --- a/dts/Bindings/unittest.txt +++ b/dts/Bindings/unittest.txt @@ -1,60 +1,60 @@ -1) OF selftest platform device +1) OF unittest platform device -** selftest +** unittest Required properties: -- compatible: must be "selftest" +- compatible: must be "unittest" All other properties are optional. Example: - selftest { - compatible = "selftest"; + unittest { + compatible = "unittest"; status = "okay"; }; -2) OF selftest i2c adapter platform device +2) OF unittest i2c adapter platform device ** platform device unittest adapter Required properties: -- compatible: must be selftest-i2c-bus +- compatible: must be unittest-i2c-bus -Children nodes contain selftest i2c devices. +Children nodes contain unittest i2c devices. Example: - selftest-i2c-bus { - compatible = "selftest-i2c-bus"; + unittest-i2c-bus { + compatible = "unittest-i2c-bus"; status = "okay"; }; -3) OF selftest i2c device +3) OF unittest i2c device -** I2C selftest device +** I2C unittest device Required properties: -- compatible: must be selftest-i2c-dev +- compatible: must be unittest-i2c-dev All other properties are optional Example: - selftest-i2c-dev { - compatible = "selftest-i2c-dev"; + unittest-i2c-dev { + compatible = "unittest-i2c-dev"; status = "okay"; }; -4) OF selftest i2c mux device +4) OF unittest i2c mux device -** I2C selftest mux +** I2C unittest mux Required properties: -- compatible: must be selftest-i2c-mux +- compatible: must be unittest-i2c-mux -Children nodes contain selftest i2c bus nodes per channel. +Children nodes contain unittest i2c bus nodes per channel. Example: - selftest-i2c-mux { - compatible = "selftest-i2c-mux"; + unittest-i2c-mux { + compatible = "unittest-i2c-mux"; status = "okay"; #address-cells = <1>; #size-cells = <0>; @@ -64,7 +64,7 @@ Example: #size-cells = <0>; i2c-dev { reg = <8>; - compatible = "selftest-i2c-dev"; + compatible = "unittest-i2c-dev"; status = "okay"; }; }; diff --git a/dts/Bindings/mips/brcm/usb.txt b/dts/Bindings/usb/brcm,bcm3384-usb.txt index 452c45c7bf..452c45c7bf 100644 --- a/dts/Bindings/mips/brcm/usb.txt +++ b/dts/Bindings/usb/brcm,bcm3384-usb.txt diff --git a/dts/Bindings/usb/dwc3.txt b/dts/Bindings/usb/dwc3.txt index cd7f0454e1..5cc364309e 100644 --- a/dts/Bindings/usb/dwc3.txt +++ b/dts/Bindings/usb/dwc3.txt @@ -14,6 +14,7 @@ Optional properties: - phys: from the *Generic PHY* bindings - phy-names: from the *Generic PHY* bindings - tx-fifo-resize: determines if the FIFO *has* to be reallocated. + - snps,usb3_lpm_capable: determines if platform is USB3 LPM capable - snps,disable_scramble_quirk: true when SW should disable data scrambling. Only really useful for FPGA builds. - snps,has-lpm-erratum: true when DWC3 was configured with LPM Erratum enabled diff --git a/dts/Bindings/usb/renesas_usbhs.txt b/dts/Bindings/usb/renesas_usbhs.txt index 61b045b6d5..dc2a18f0b3 100644 --- a/dts/Bindings/usb/renesas_usbhs.txt +++ b/dts/Bindings/usb/renesas_usbhs.txt @@ -15,7 +15,10 @@ Optional properties: - phys: phandle + phy specifier pair - phy-names: must be "usb" - dmas: Must contain a list of references to DMA specifiers. - - dma-names : Must contain a list of DMA names, "tx" or "rx". + - dma-names : Must contain a list of DMA names: + - tx0 ... tx<n> + - rx0 ... rx<n> + - This <n> means DnFIFO in USBHS module. Example: usbhs: usb@e6590000 { diff --git a/dts/Bindings/usb/usbmisc-imx.txt b/dts/Bindings/usb/usbmisc-imx.txt index c101a4b171..3539d4e7d2 100644 --- a/dts/Bindings/usb/usbmisc-imx.txt +++ b/dts/Bindings/usb/usbmisc-imx.txt @@ -5,6 +5,7 @@ Required properties: - compatible: Should be one of below: "fsl,imx6q-usbmisc" for imx6q "fsl,vf610-usbmisc" for Vybrid vf610 + "fsl,imx6sx-usbmisc" for imx6sx - reg: Should contain registers location and length Examples: diff --git a/dts/Bindings/vendor-prefixes.txt b/dts/Bindings/vendor-prefixes.txt index fae26d014a..80339192c9 100644 --- a/dts/Bindings/vendor-prefixes.txt +++ b/dts/Bindings/vendor-prefixes.txt @@ -11,18 +11,22 @@ adapteva Adapteva, Inc. adh AD Holdings Plc. adi Analog Devices, Inc. aeroflexgaisler Aeroflex Gaisler AB +al Annapurna Labs allwinner Allwinner Technology Co., Ltd. alphascale AlphaScale Integrated Circuits Systems, Inc. altr Altera Corp. amcc Applied Micro Circuits Corporation (APM, formally AMCC) amd Advanced Micro Devices (AMD), Inc. amlogic Amlogic, Inc. +ampire Ampire Co., Ltd. ams AMS AG amstaos AMS-Taos Inc. apm Applied Micro Circuits Corporation (APM) +aptina Aptina Imaging arasan Arasan Chip Systems arm ARM Ltd. armadeus ARMadeus Systems SARL +artesyn Artesyn Embedded Technologies Inc. asahi-kasei Asahi Kasei Corp. atmel Atmel Corporation auo AU Optronics Corporation @@ -37,6 +41,7 @@ capella Capella Microsystems, Inc cavium Cavium, Inc. cdns Cadence Design Systems Inc. chipidea Chipidea, Inc +chipone ChipOne chipspark ChipSPARK chrp Common Hardware Reference Platform chunghwa Chunghwa Picture Tubes Ltd. @@ -78,7 +83,9 @@ geniatech Geniatech, Inc. giantplus Giantplus Technology Co., Ltd. globalscale Globalscale Technologies, Inc. gmt Global Mixed-mode Technology, Inc. +goodix Shenzhen Huiding Technology Co., Ltd. google Google, Inc. +grinn Grinn gumstix Gumstix, Inc. gw Gateworks Corporation hannstar HannStar Display Corporation @@ -114,6 +121,7 @@ merrii Merrii Technology Co., Ltd. micrel Micrel Inc. microchip Microchip Technology Inc. micron Micron Technology Inc. +minix MINIX Technology Ltd. mitsubishi Mitsubishi Electric Corporation mosaixtech Mosaix Technologies, Inc. moxa Moxa @@ -125,6 +133,7 @@ mxicy Macronix International Co., Ltd. national National Semiconductor neonode Neonode Inc. netgear NETGEAR +netlogic Broadcom Corporation (formerly NetLogic Microsystems) newhaven Newhaven Display International nintendo Nintendo nokia Nokia @@ -132,6 +141,7 @@ nvidia NVIDIA nxp NXP Semiconductors onnn ON Semiconductor Corp. opencores OpenCores.org +ortustech Ortus Technology Co., Ltd. ovti OmniVision Technologies panasonic Panasonic Corporation parade Parade Technologies Inc. @@ -167,6 +177,7 @@ sii Seiko Instruments, Inc. silergy Silergy Corp. sirf SiRF Technology, Inc. sitronix Sitronix Technology Corporation +skyworks Skyworks Solutions, Inc. smsc Standard Microsystems Corporation snps Synopsys, Inc. solidrun SolidRun @@ -194,6 +205,7 @@ voipac Voipac Technologies s.r.o. winbond Winbond Electronics corp. wlf Wolfson Microelectronics wm Wondermedia Technologies, Inc. +x-powers X-Powers xes Extreme Engineering Solutions (X-ES) xillybus Xillybus Ltd. xlnx Xilinx diff --git a/dts/Bindings/video/atmel,lcdc.txt b/dts/Bindings/video/atmel,lcdc.txt index f059dd0b3d..ecb8da063d 100644 --- a/dts/Bindings/video/atmel,lcdc.txt +++ b/dts/Bindings/video/atmel,lcdc.txt @@ -10,7 +10,9 @@ Required properties: "atmel,at91sam9g45es-lcdc" , "atmel,at91sam9rl-lcdc" , "atmel,at32ap-lcdc" -- reg : Should contain 1 register ranges(address and length) +- reg : Should contain 1 register ranges(address and length). + Can contain an additional register range(address and length) + for fixed framebuffer memory. Useful for dedicated memories. - interrupts : framebuffer controller interrupt - display: a phandle pointing to the display node @@ -38,6 +40,14 @@ Example: }; +Example for fixed framebuffer memory: + + fb0: fb@0x00500000 { + compatible = "atmel,at91sam9263-lcdc"; + reg = <0x00700000 0x1000 0x70000000 0x200000>; + [...] + }; + Atmel LCDC Display ----------------------------------------------------- Required properties (as per of_videomode_helper): diff --git a/dts/Bindings/video/backlight/sky81452-backlight.txt b/dts/Bindings/video/backlight/sky81452-backlight.txt new file mode 100644 index 0000000000..8bf2940f54 --- /dev/null +++ b/dts/Bindings/video/backlight/sky81452-backlight.txt @@ -0,0 +1,29 @@ +SKY81452-backlight bindings + +Required properties: +- compatible : Must be "skyworks,sky81452-backlight" + +Optional properties: +- name : Name of backlight device. Default is 'lcd-backlight'. +- gpios : GPIO to use to EN pin. + See Documentation/devicetree/bindings/gpio/gpio.txt +- led-sources : List of enabled channels from 0 to 5. + See Documentation/devicetree/bindings/leds/common.txt +- skyworks,ignore-pwm : Ignore both PWM input +- skyworks,dpwm-mode : Enable DPWM dimming mode, otherwise Analog dimming. +- skyworks,phase-shift : Enable phase shift mode +- skyworks,short-detection-threshold-volt + : It should be one of 4, 5, 6 and 7V. +- skyworks,current-limit-mA + : It should be 2300mA or 2750mA. + +Example: + + backlight { + compatible = "skyworks,sky81452-backlight"; + name = "pwm-backlight"; + led-sources = <0 1 2 5>; + skyworks,ignore-pwm; + skyworks,phase-shift; + skyworks,current-limit-mA = <2300>; + }; diff --git a/dts/Bindings/video/ti,omap-dss.txt b/dts/Bindings/video/ti,omap-dss.txt index d5f1a3fe31..e1ef295693 100644 --- a/dts/Bindings/video/ti,omap-dss.txt +++ b/dts/Bindings/video/ti,omap-dss.txt @@ -25,8 +25,8 @@ Video Ports ----------- The DSS Core and the encoders have video port outputs. The structure of the -video ports is described in Documentation/devicetree/bindings/video/video- -ports.txt, and the properties for the ports and endpoints for each encoder are +video ports is described in Documentation/devicetree/bindings/graph.txt, +and the properties for the ports and endpoints for each encoder are described in the SoC's DSS binding documentation. The video ports are used to describe the connections to external hardware, like diff --git a/dts/Bindings/arm/bcm/kona-wdt.txt b/dts/Bindings/watchdog/brcm,kona-wdt.txt index 2b86a00e35..2b86a00e35 100644 --- a/dts/Bindings/arm/bcm/kona-wdt.txt +++ b/dts/Bindings/watchdog/brcm,kona-wdt.txt |