diff options
Diffstat (limited to 'dts/include/dt-bindings/usb/pd.h')
| -rw-r--r-- | dts/include/dt-bindings/usb/pd.h | 382 |
1 files changed, 381 insertions, 1 deletions
diff --git a/dts/include/dt-bindings/usb/pd.h b/dts/include/dt-bindings/usb/pd.h index 985f2bbd4d..e6526b1381 100644 --- a/dts/include/dt-bindings/usb/pd.h +++ b/dts/include/dt-bindings/usb/pd.h @@ -85,4 +85,384 @@ PDO_PPS_APDO_MIN_VOLT(min_mv) | PDO_PPS_APDO_MAX_VOLT(max_mv) | \ PDO_PPS_APDO_MAX_CURR(max_ma)) - #endif /* __DT_POWER_DELIVERY_H */ + /* + * Based on "Table 6-14 Fixed Supply PDO - Sink" of "USB Power Delivery Specification Revision 3.0, + * Version 1.2" + * Initial current capability of the new source when vSafe5V is applied. + */ +#define FRS_DEFAULT_POWER 1 +#define FRS_5V_1P5A 2 +#define FRS_5V_3A 3 + +/* + * SVDM Identity Header + * -------------------- + * <31> :: data capable as a USB host + * <30> :: data capable as a USB device + * <29:27> :: product type (UFP / Cable / VPD) + * <26> :: modal operation supported (1b == yes) + * <25:23> :: product type (DFP) (SVDM version 2.0+ only; set to zero in version 1.0) + * <22:21> :: connector type (SVDM version 2.0+ only; set to zero in version 1.0) + * <20:16> :: Reserved, Shall be set to zero + * <15:0> :: USB-IF assigned VID for this cable vendor + */ + +/* PD Rev2.0 definition */ +#define IDH_PTYPE_UNDEF 0 + +/* SOP Product Type (UFP) */ +#define IDH_PTYPE_NOT_UFP 0 +#define IDH_PTYPE_HUB 1 +#define IDH_PTYPE_PERIPH 2 +#define IDH_PTYPE_PSD 3 +#define IDH_PTYPE_AMA 5 + +/* SOP' Product Type (Cable Plug / VPD) */ +#define IDH_PTYPE_NOT_CABLE 0 +#define IDH_PTYPE_PCABLE 3 +#define IDH_PTYPE_ACABLE 4 +#define IDH_PTYPE_VPD 6 + +/* SOP Product Type (DFP) */ +#define IDH_PTYPE_NOT_DFP 0 +#define IDH_PTYPE_DFP_HUB 1 +#define IDH_PTYPE_DFP_HOST 2 +#define IDH_PTYPE_DFP_PB 3 + +#define VDO_IDH(usbh, usbd, ufp_cable, is_modal, dfp, conn, vid) \ + ((usbh) << 31 | (usbd) << 30 | ((ufp_cable) & 0x7) << 27 \ + | (is_modal) << 26 | ((dfp) & 0x7) << 23 | ((conn) & 0x3) << 21 \ + | ((vid) & 0xffff)) + +/* + * Cert Stat VDO + * ------------- + * <31:0> : USB-IF assigned XID for this cable + */ +#define VDO_CERT(xid) ((xid) & 0xffffffff) + +/* + * Product VDO + * ----------- + * <31:16> : USB Product ID + * <15:0> : USB bcdDevice + */ +#define VDO_PRODUCT(pid, bcd) (((pid) & 0xffff) << 16 | ((bcd) & 0xffff)) + +/* + * UFP VDO (PD Revision 3.0+ only) + * -------- + * <31:29> :: UFP VDO version + * <28> :: Reserved + * <27:24> :: Device capability + * <23:22> :: Connector type (10b == receptacle, 11b == captive plug) + * <21:11> :: Reserved + * <10:8> :: Vconn power (AMA only) + * <7> :: Vconn required (AMA only, 0b == no, 1b == yes) + * <6> :: Vbus required (AMA only, 0b == yes, 1b == no) + * <5:3> :: Alternate modes + * <2:0> :: USB highest speed + */ +/* UFP VDO Version */ +#define UFP_VDO_VER1_2 2 + +/* Device Capability */ +#define DEV_USB2_CAPABLE (1 << 0) +#define DEV_USB2_BILLBOARD (1 << 1) +#define DEV_USB3_CAPABLE (1 << 2) +#define DEV_USB4_CAPABLE (1 << 3) + +/* Connector Type */ +#define UFP_RECEPTACLE 2 +#define UFP_CAPTIVE 3 + +/* Vconn Power (AMA only, set to AMA_VCONN_NOT_REQ if Vconn is not required) */ +#define AMA_VCONN_PWR_1W 0 +#define AMA_VCONN_PWR_1W5 1 +#define AMA_VCONN_PWR_2W 2 +#define AMA_VCONN_PWR_3W 3 +#define AMA_VCONN_PWR_4W 4 +#define AMA_VCONN_PWR_5W 5 +#define AMA_VCONN_PWR_6W 6 + +/* Vconn Required (AMA only) */ +#define AMA_VCONN_NOT_REQ 0 +#define AMA_VCONN_REQ 1 + +/* Vbus Required (AMA only) */ +#define AMA_VBUS_REQ 0 +#define AMA_VBUS_NOT_REQ 1 + +/* Alternate Modes */ +#define UFP_ALTMODE_NOT_SUPP 0 +#define UFP_ALTMODE_TBT3 (1 << 0) +#define UFP_ALTMODE_RECFG (1 << 1) +#define UFP_ALTMODE_NO_RECFG (1 << 2) + +/* USB Highest Speed */ +#define UFP_USB2_ONLY 0 +#define UFP_USB32_GEN1 1 +#define UFP_USB32_4_GEN2 2 +#define UFP_USB4_GEN3 3 + +#define VDO_UFP(ver, cap, conn, vcpwr, vcr, vbr, alt, spd) \ + (((ver) & 0x7) << 29 | ((cap) & 0xf) << 24 | ((conn) & 0x3) << 22 \ + | ((vcpwr) & 0x7) << 8 | (vcr) << 7 | (vbr) << 6 | ((alt) & 0x7) << 3 \ + | ((spd) & 0x7)) + +/* + * DFP VDO (PD Revision 3.0+ only) + * -------- + * <31:29> :: DFP VDO version + * <28:27> :: Reserved + * <26:24> :: Host capability + * <23:22> :: Connector type (10b == receptacle, 11b == captive plug) + * <21:5> :: Reserved + * <4:0> :: Port number + */ +#define DFP_VDO_VER1_1 1 +#define HOST_USB2_CAPABLE (1 << 0) +#define HOST_USB3_CAPABLE (1 << 1) +#define HOST_USB4_CAPABLE (1 << 2) +#define DFP_RECEPTACLE 2 +#define DFP_CAPTIVE 3 + +#define VDO_DFP(ver, cap, conn, pnum) \ + (((ver) & 0x7) << 29 | ((cap) & 0x7) << 24 | ((conn) & 0x3) << 22 \ + | ((pnum) & 0x1f)) + +/* + * Cable VDO (for both Passive and Active Cable VDO in PD Rev2.0) + * --------- + * <31:28> :: Cable HW version + * <27:24> :: Cable FW version + * <23:20> :: Reserved, Shall be set to zero + * <19:18> :: type-C to Type-A/B/C/Captive (00b == A, 01 == B, 10 == C, 11 == Captive) + * <17> :: Reserved, Shall be set to zero + * <16:13> :: cable latency (0001 == <10ns(~1m length)) + * <12:11> :: cable termination type (11b == both ends active VCONN req) + * <10> :: SSTX1 Directionality support (0b == fixed, 1b == cfgable) + * <9> :: SSTX2 Directionality support + * <8> :: SSRX1 Directionality support + * <7> :: SSRX2 Directionality support + * <6:5> :: Vbus current handling capability (01b == 3A, 10b == 5A) + * <4> :: Vbus through cable (0b == no, 1b == yes) + * <3> :: SOP" controller present? (0b == no, 1b == yes) + * <2:0> :: USB SS Signaling support + * + * Passive Cable VDO (PD Rev3.0+) + * --------- + * <31:28> :: Cable HW version + * <27:24> :: Cable FW version + * <23:21> :: VDO version + * <20> :: Reserved, Shall be set to zero + * <19:18> :: Type-C to Type-C/Captive (10b == C, 11b == Captive) + * <17> :: Reserved, Shall be set to zero + * <16:13> :: cable latency (0001 == <10ns(~1m length)) + * <12:11> :: cable termination type (10b == Vconn not req, 01b == Vconn req) + * <10:9> :: Maximum Vbus voltage (00b == 20V, 01b == 30V, 10b == 40V, 11b == 50V) + * <8:7> :: Reserved, Shall be set to zero + * <6:5> :: Vbus current handling capability (01b == 3A, 10b == 5A) + * <4:3> :: Reserved, Shall be set to zero + * <2:0> :: USB highest speed + * + * Active Cable VDO 1 (PD Rev3.0+) + * --------- + * <31:28> :: Cable HW version + * <27:24> :: Cable FW version + * <23:21> :: VDO version + * <20> :: Reserved, Shall be set to zero + * <19:18> :: Connector type (10b == C, 11b == Captive) + * <17> :: Reserved, Shall be set to zero + * <16:13> :: cable latency (0001 == <10ns(~1m length)) + * <12:11> :: cable termination type (10b == one end active, 11b == both ends active VCONN req) + * <10:9> :: Maximum Vbus voltage (00b == 20V, 01b == 30V, 10b == 40V, 11b == 50V) + * <8> :: SBU supported (0b == supported, 1b == not supported) + * <7> :: SBU type (0b == passive, 1b == active) + * <6:5> :: Vbus current handling capability (01b == 3A, 10b == 5A) + * <4> :: Vbus through cable (0b == no, 1b == yes) + * <3> :: SOP" controller present? (0b == no, 1b == yes) + * <2:0> :: USB highest speed + */ +/* Cable VDO Version */ +#define CABLE_VDO_VER1_0 0 +#define CABLE_VDO_VER1_3 3 + +/* Connector Type (_ATYPE and _BTYPE are for PD Rev2.0 only) */ +#define CABLE_ATYPE 0 +#define CABLE_BTYPE 1 +#define CABLE_CTYPE 2 +#define CABLE_CAPTIVE 3 + +/* Cable Latency */ +#define CABLE_LATENCY_1M 1 +#define CABLE_LATENCY_2M 2 +#define CABLE_LATENCY_3M 3 +#define CABLE_LATENCY_4M 4 +#define CABLE_LATENCY_5M 5 +#define CABLE_LATENCY_6M 6 +#define CABLE_LATENCY_7M 7 +#define CABLE_LATENCY_7M_PLUS 8 + +/* Cable Termination Type */ +#define PCABLE_VCONN_NOT_REQ 0 +#define PCABLE_VCONN_REQ 1 +#define ACABLE_ONE_END 2 +#define ACABLE_BOTH_END 3 + +/* Maximum Vbus Voltage */ +#define CABLE_MAX_VBUS_20V 0 +#define CABLE_MAX_VBUS_30V 1 +#define CABLE_MAX_VBUS_40V 2 +#define CABLE_MAX_VBUS_50V 3 + +/* Active Cable SBU Supported/Type */ +#define ACABLE_SBU_SUPP 0 +#define ACABLE_SBU_NOT_SUPP 1 +#define ACABLE_SBU_PASSIVE 0 +#define ACABLE_SBU_ACTIVE 1 + +/* Vbus Current Handling Capability */ +#define CABLE_CURR_DEF 0 +#define CABLE_CURR_3A 1 +#define CABLE_CURR_5A 2 + +/* USB SuperSpeed Signaling Support (PD Rev2.0) */ +#define CABLE_USBSS_U2_ONLY 0 +#define CABLE_USBSS_U31_GEN1 1 +#define CABLE_USBSS_U31_GEN2 2 + +/* USB Highest Speed */ +#define CABLE_USB2_ONLY 0 +#define CABLE_USB32_GEN1 1 +#define CABLE_USB32_4_GEN2 2 +#define CABLE_USB4_GEN3 3 + +#define VDO_CABLE(hw, fw, cbl, lat, term, tx1d, tx2d, rx1d, rx2d, cur, vps, sopp, usbss) \ + (((hw) & 0x7) << 28 | ((fw) & 0x7) << 24 | ((cbl) & 0x3) << 18 \ + | ((lat) & 0x7) << 13 | ((term) & 0x3) << 11 | (tx1d) << 10 \ + | (tx2d) << 9 | (rx1d) << 8 | (rx2d) << 7 | ((cur) & 0x3) << 5 \ + | (vps) << 4 | (sopp) << 3 | ((usbss) & 0x7)) +#define VDO_PCABLE(hw, fw, ver, conn, lat, term, vbm, cur, spd) \ + (((hw) & 0xf) << 28 | ((fw) & 0xf) << 24 | ((ver) & 0x7) << 21 \ + | ((conn) & 0x3) << 18 | ((lat) & 0xf) << 13 | ((term) & 0x3) << 11 \ + | ((vbm) & 0x3) << 9 | ((cur) & 0x3) << 5 | ((spd) & 0x7)) +#define VDO_ACABLE1(hw, fw, ver, conn, lat, term, vbm, sbu, sbut, cur, vbt, sopp, spd) \ + (((hw) & 0xf) << 28 | ((fw) & 0xf) << 24 | ((ver) & 0x7) << 21 \ + | ((conn) & 0x3) << 18 | ((lat) & 0xf) << 13 | ((term) & 0x3) << 11 \ + | ((vbm) & 0x3) << 9 | (sbu) << 8 | (sbut) << 7 | ((cur) & 0x3) << 5 \ + | (vbt) << 4 | (sopp) << 3 | ((spd) & 0x7)) + +/* + * Active Cable VDO 2 + * --------- + * <31:24> :: Maximum operating temperature + * <23:16> :: Shutdown temperature + * <15> :: Reserved, Shall be set to zero + * <14:12> :: U3/CLd power + * <11> :: U3 to U0 transition mode (0b == direct, 1b == through U3S) + * <10> :: Physical connection (0b == copper, 1b == optical) + * <9> :: Active element (0b == redriver, 1b == retimer) + * <8> :: USB4 supported (0b == yes, 1b == no) + * <7:6> :: USB2 hub hops consumed + * <5> :: USB2 supported (0b == yes, 1b == no) + * <4> :: USB3.2 supported (0b == yes, 1b == no) + * <3> :: USB lanes supported (0b == one lane, 1b == two lanes) + * <2> :: Optically isolated active cable (0b == no, 1b == yes) + * <1> :: Reserved, Shall be set to zero + * <0> :: USB gen (0b == gen1, 1b == gen2+) + */ +/* U3/CLd Power*/ +#define ACAB2_U3_CLD_10MW_PLUS 0 +#define ACAB2_U3_CLD_10MW 1 +#define ACAB2_U3_CLD_5MW 2 +#define ACAB2_U3_CLD_1MW 3 +#define ACAB2_U3_CLD_500UW 4 +#define ACAB2_U3_CLD_200UW 5 +#define ACAB2_U3_CLD_50UW 6 + +/* Other Active Cable VDO 2 Fields */ +#define ACAB2_U3U0_DIRECT 0 +#define ACAB2_U3U0_U3S 1 +#define ACAB2_PHY_COPPER 0 +#define ACAB2_PHY_OPTICAL 1 +#define ACAB2_REDRIVER 0 +#define ACAB2_RETIMER 1 +#define ACAB2_USB4_SUPP 0 +#define ACAB2_USB4_NOT_SUPP 1 +#define ACAB2_USB2_SUPP 0 +#define ACAB2_USB2_NOT_SUPP 1 +#define ACAB2_USB32_SUPP 0 +#define ACAB2_USB32_NOT_SUPP 1 +#define ACAB2_LANES_ONE 0 +#define ACAB2_LANES_TWO 1 +#define ACAB2_OPT_ISO_NO 0 +#define ACAB2_OPT_ISO_YES 1 +#define ACAB2_GEN_1 0 +#define ACAB2_GEN_2_PLUS 1 + +#define VDO_ACABLE2(mtemp, stemp, u3p, trans, phy, ele, u4, hops, u2, u32, lane, iso, gen) \ + (((mtemp) & 0xff) << 24 | ((stemp) & 0xff) << 16 | ((u3p) & 0x7) << 12 \ + | (trans) << 11 | (phy) << 10 | (ele) << 9 | (u4) << 8 \ + | ((hops) & 0x3) << 6 | (u2) << 5 | (u32) << 4 | (lane) << 3 \ + | (iso) << 2 | (gen)) + +/* + * AMA VDO (PD Rev2.0) + * --------- + * <31:28> :: Cable HW version + * <27:24> :: Cable FW version + * <23:12> :: Reserved, Shall be set to zero + * <11> :: SSTX1 Directionality support (0b == fixed, 1b == cfgable) + * <10> :: SSTX2 Directionality support + * <9> :: SSRX1 Directionality support + * <8> :: SSRX2 Directionality support + * <7:5> :: Vconn power + * <4> :: Vconn power required + * <3> :: Vbus power required + * <2:0> :: USB SS Signaling support + */ +#define VDO_AMA(hw, fw, tx1d, tx2d, rx1d, rx2d, vcpwr, vcr, vbr, usbss) \ + (((hw) & 0x7) << 28 | ((fw) & 0x7) << 24 \ + | (tx1d) << 11 | (tx2d) << 10 | (rx1d) << 9 | (rx2d) << 8 \ + | ((vcpwr) & 0x7) << 5 | (vcr) << 4 | (vbr) << 3 \ + | ((usbss) & 0x7)) + +#define PD_VDO_AMA_VCONN_REQ(vdo) (((vdo) >> 4) & 1) +#define PD_VDO_AMA_VBUS_REQ(vdo) (((vdo) >> 3) & 1) + +#define AMA_USBSS_U2_ONLY 0 +#define AMA_USBSS_U31_GEN1 1 +#define AMA_USBSS_U31_GEN2 2 +#define AMA_USBSS_BBONLY 3 + +/* + * VPD VDO + * --------- + * <31:28> :: HW version + * <27:24> :: FW version + * <23:21> :: VDO version + * <20:17> :: Reserved, Shall be set to zero + * <16:15> :: Maximum Vbus voltage (00b == 20V, 01b == 30V, 10b == 40V, 11b == 50V) + * <14> :: Charge through current support (0b == 3A, 1b == 5A) + * <13> :: Reserved, Shall be set to zero + * <12:7> :: Vbus impedance + * <6:1> :: Ground impedance + * <0> :: Charge through support (0b == no, 1b == yes) + */ +#define VPD_VDO_VER1_0 0 +#define VPD_MAX_VBUS_20V 0 +#define VPD_MAX_VBUS_30V 1 +#define VPD_MAX_VBUS_40V 2 +#define VPD_MAX_VBUS_50V 3 +#define VPDCT_CURR_3A 0 +#define VPDCT_CURR_5A 1 +#define VPDCT_NOT_SUPP 0 +#define VPDCT_SUPP 1 + +#define VDO_VPD(hw, fw, ver, vbm, curr, vbi, gi, ct) \ + (((hw) & 0xf) << 28 | ((fw) & 0xf) << 24 | ((ver) & 0x7) << 21 \ + | ((vbm) & 0x3) << 15 | (curr) << 14 | ((vbi) & 0x3f) << 7 \ + | ((gi) & 0x3f) << 1 | (ct)) + +#endif /* __DT_POWER_DELIVERY_H */ |