diff options
Diffstat (limited to 'dts/src/arm/armada-370-synology-ds213j.dts')
-rw-r--r-- | dts/src/arm/armada-370-synology-ds213j.dts | 312 |
1 files changed, 0 insertions, 312 deletions
diff --git a/dts/src/arm/armada-370-synology-ds213j.dts b/dts/src/arm/armada-370-synology-ds213j.dts deleted file mode 100644 index 64f2ce254f..0000000000 --- a/dts/src/arm/armada-370-synology-ds213j.dts +++ /dev/null @@ -1,312 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0+ OR MIT) -/* - * Device Tree file for Synology DS213j - * - * Copyright (C) 2014, Arnaud EBALARD <arno@natisbad.org> - * - * Note: this Device Tree assumes that the bootloader has remapped the - * internal registers to 0xf1000000 (instead of the old 0xd0000000). - * The 0xf1000000 is the default used by the recent, DT-capable, U-Boot - * bootloaders provided by Marvell. It is used in recent versions of - * DSM software provided by Synology. Nonetheless, some earlier boards - * were delivered with an older version of u-boot that left internal - * registers mapped at 0xd0000000. If you have such a device you will - * not be able to directly boot a kernel based on this Device Tree. In - * that case, the preferred solution is to update your bootloader (e.g. - * by upgrading to latest version of DSM, or building a new one and - * installing it from u-boot prompt) or adjust the Devive Tree - * (s/0xf1000000/0xd0000000/ in 'ranges' below). - */ - -/dts-v1/; - -#include <dt-bindings/input/input.h> -#include <dt-bindings/gpio/gpio.h> -#include "armada-370.dtsi" - -/ { - model = "Synology DS213j"; - compatible = "synology,ds213j", "marvell,armada370", - "marvell,armada-370-xp"; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - memory@0 { - device_type = "memory"; - reg = <0x00000000 0x20000000>; /* 512 MB */ - }; - - soc { - ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 - MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000 - MBUS_ID(0x09, 0x01) 0 0xf1100000 0x10000>; - - internal-regs { - - /* RTC provided by Seiko S-35390A I2C RTC chip below */ - rtc@10300 { - status = "disabled"; - }; - - i2c@11000 { - compatible = "marvell,mv64xxx-i2c"; - pinctrl-0 = <&i2c0_pins>; - pinctrl-names = "default"; - clock-frequency = <400000>; - status = "okay"; - - /* Main device RTC chip */ - s35390a: s35390a@30 { - compatible = "sii,s35390a"; - reg = <0x30>; - }; - }; - - /* Connected to a header on device's PCB */ - serial@12000 { - status = "okay"; - }; - - /* Connected to a TI MSP430F2111 for power control */ - serial@12100 { - status = "okay"; - }; - - poweroff@12100 { - compatible = "synology,power-off"; - reg = <0x12100 0x100>; - clocks = <&coreclk 0>; - }; - - /* rear USB port, near reset button */ - usb@50000 { - status = "okay"; - }; - - /* rear USB port, near RJ45 port */ - usb@51000 { - status = "okay"; - }; - - ethernet@70000 { - status = "okay"; - phy = <&phy1>; - phy-mode = "sgmii"; - }; - - sata@a0000 { - nr-ports = <2>; - status = "okay"; - }; - }; - }; - - gpio-fan-32-38 { - status = "okay"; - compatible = "gpio-fan"; - pinctrl-0 = <&fan_ctrl_low_pin &fan_ctrl_mid_pin - &fan_ctrl_high_pin &fan_alarm_pin>; - pinctrl-names = "default"; - gpios = <&gpio1 31 GPIO_ACTIVE_HIGH - &gpio2 0 GPIO_ACTIVE_HIGH - &gpio2 1 GPIO_ACTIVE_HIGH>; - alarm-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; - gpio-fan,speed-map = < 0 0 - 1000 1 - 1150 2 - 1350 4 - 1500 3 - 1650 5 - 1750 6 - 1900 7 >; - }; - - gpio-leds { - compatible = "gpio-leds"; - pinctrl-0 = <&disk1_led_pin - &disk2_led_pin>; - pinctrl-names = "default"; - - disk1-led-amber { - label = "synology:amber:disk1"; - gpios = <&gpio0 31 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - - disk2-led-amber { - label = "synology:amber:disk2"; - gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - }; - - regulators { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-0 = <&sata1_pwr_pin &sata2_pwr_pin>; - pinctrl-names = "default"; - - sata1_regulator: sata1-regulator@1 { - compatible = "regulator-fixed"; - reg = <1>; - regulator-name = "SATA1 Power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - startup-delay-us = <2000000>; - enable-active-high; - regulator-always-on; - regulator-boot-on; - gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>; - }; - - sata2_regulator: sata2-regulator@2 { - compatible = "regulator-fixed"; - reg = <2>; - regulator-name = "SATA2 Power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - startup-delay-us = <4000000>; - enable-active-high; - regulator-always-on; - regulator-boot-on; - gpio = <&gpio1 30 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&mdio { - phy1: ethernet-phy@1 { /* Marvell 88E1512 */ - reg = <1>; - }; -}; - -&pinctrl { - disk1_led_pin: disk1-led-pin { - marvell,pins = "mpp31"; - marvell,function = "gpio"; - }; - - disk2_led_pin: disk2-led-pin { - marvell,pins = "mpp32"; - marvell,function = "gpio"; - }; - - sata1_pwr_pin: sata1-pwr-pin { - marvell,pins = "mpp37"; - marvell,function = "gpio"; - }; - - sata2_pwr_pin: sata2-pwr-pin { - marvell,pins = "mpp62"; - marvell,function = "gpio"; - }; - - sata1_pres_pin: sata1-pres-pin { - marvell,pins = "mpp60"; - marvell,function = "gpio"; - }; - - sata2_pres_pin: sata2-pres-pin { - marvell,pins = "mpp48"; - marvell,function = "gpio"; - }; - - syno_id_bit0_pin: syno-id-bit0-pin { - marvell,pins = "mpp55"; - marvell,function = "gpio"; - }; - - syno_id_bit1_pin: syno-id-bit1-pin { - marvell,pins = "mpp56"; - marvell,function = "gpio"; - }; - - syno_id_bit2_pin: syno-id-bit2-pin { - marvell,pins = "mpp57"; - marvell,function = "gpio"; - }; - - syno_id_bit3_pin: syno-id-bit3-pin { - marvell,pins = "mpp58"; - marvell,function = "gpio"; - }; - - fan_ctrl_low_pin: fan-ctrl-low-pin { - marvell,pins = "mpp65"; - marvell,function = "gpio"; - }; - - fan_ctrl_mid_pin: fan-ctrl-mid-pin { - marvell,pins = "mpp64"; - marvell,function = "gpio"; - }; - - fan_ctrl_high_pin: fan-ctrl-high-pin { - marvell,pins = "mpp63"; - marvell,function = "gpio"; - }; - - fan_alarm_pin: fan-alarm-pin { - marvell,pins = "mpp38"; - marvell,function = "gpio"; - }; -}; - -&spi0 { - status = "okay"; - - spi-flash@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "micron,n25q064", "jedec,spi-nor"; - reg = <0>; /* Chip select 0 */ - spi-max-frequency = <20000000>; - - /* - * Warning! - * - * Synology u-boot uses its compiled-in environment - * and it seems Synology did not care to change u-boot - * default configuration in order to allow saving a - * modified environment at a sensible location. So, - * if you do a 'saveenv' under u-boot, your modified - * environment will be saved at 1MB after the start - * of the flash, i.e. in the middle of the uImage. - * For that reason, it is strongly advised not to - * change the default environment, unless you know - * what you are doing. - */ - partition@0 { /* u-boot */ - label = "RedBoot"; - reg = <0x00000000 0x000c0000>; /* 768KB */ - }; - - partition@c0000 { /* uImage */ - label = "zImage"; - reg = <0x000c0000 0x002d0000>; /* 2880KB */ - }; - - partition@390000 { /* uInitramfs */ - label = "rd.gz"; - reg = <0x00390000 0x00440000>; /* 4250KB */ - }; - - partition@7d0000 { /* MAC address and serial number */ - label = "vendor"; - reg = <0x007d0000 0x00010000>; /* 64KB */ - }; - - partition@7e0000 { - label = "RedBoot config"; - reg = <0x007e0000 0x00010000>; /* 64KB */ - }; - - partition@7f0000 { - label = "FIS directory"; - reg = <0x007f0000 0x00010000>; /* 64KB */ - }; - }; -}; |