diff options
Diffstat (limited to 'dts/src/arm/armada-xp-linksys-mamba.dts')
-rw-r--r-- | dts/src/arm/armada-xp-linksys-mamba.dts | 399 |
1 files changed, 0 insertions, 399 deletions
diff --git a/dts/src/arm/armada-xp-linksys-mamba.dts b/dts/src/arm/armada-xp-linksys-mamba.dts deleted file mode 100644 index 8480a16919..0000000000 --- a/dts/src/arm/armada-xp-linksys-mamba.dts +++ /dev/null @@ -1,399 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0 OR MIT) -/* - * Device Tree file for the Linksys WRT1900AC (Mamba). - * - * Note: this board is shipped with a new generation boot loader that - * remaps internal registers at 0xf1000000. Therefore, if earlyprintk - * is used, the CONFIG_DEBUG_MVEBU_UART0_ALTERNATE option should be - * used. - * - * Copyright (C) 2014 Imre Kaloz <kaloz@openwrt.org> - * - * Based on armada-xp-axpwifiap.dts: - * - * Copyright (C) 2013 Marvell - * - * Thomas Petazzoni <thomas.petazzoni@free-electrons.com> - */ - -/dts-v1/; -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/input/input.h> -#include "armada-xp-mv78230.dtsi" - -/ { - model = "Linksys WRT1900AC"; - compatible = "linksys,mamba", "marvell,armadaxp-mv78230", - "marvell,armadaxp", "marvell,armada-370-xp"; - - chosen { - bootargs = "console=ttyS0,115200"; - stdout-path = &uart0; - }; - - memory@0 { - device_type = "memory"; - reg = <0x00000000 0x00000000 0x00000000 0x10000000>; /* 256MB */ - }; - - soc { - ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000 - MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000 - MBUS_ID(0x09, 0x09) 0 0 0xf1100000 0x10000 - MBUS_ID(0x09, 0x05) 0 0 0xf1110000 0x10000 - MBUS_ID(0x0c, 0x04) 0 0 0xf1200000 0x100000>; - - internal-regs { - - rtc@10300 { - /* No crystal connected to the internal RTC */ - status = "disabled"; - }; - - /* J10: VCC, NC, RX, NC, TX, GND */ - serial@12000 { - status = "okay"; - }; - - sata@a0000 { - nr-ports = <1>; - status = "okay"; - }; - - ethernet@70000 { - pinctrl-0 = <&ge0_rgmii_pins>; - pinctrl-names = "default"; - status = "okay"; - phy-mode = "rgmii-id"; - buffer-manager = <&bm>; - bm,pool-long = <0>; - bm,pool-short = <1>; - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - ethernet@74000 { - pinctrl-0 = <&ge1_rgmii_pins>; - pinctrl-names = "default"; - status = "okay"; - phy-mode = "rgmii-id"; - buffer-manager = <&bm>; - bm,pool-long = <2>; - bm,pool-short = <3>; - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - /* USB part of the eSATA/USB 2.0 port */ - usb@50000 { - status = "okay"; - }; - - i2c@11000 { - status = "okay"; - clock-frequency = <100000>; - - tmp421@4c { - compatible = "ti,tmp421"; - reg = <0x4c>; - }; - - tlc59116@68 { - #address-cells = <1>; - #size-cells = <0>; - #gpio-cells = <2>; - compatible = "ti,tlc59116"; - reg = <0x68>; - - wan_amber@0 { - label = "mamba:amber:wan"; - reg = <0x0>; - }; - - wan_white@1 { - label = "mamba:white:wan"; - reg = <0x1>; - }; - - wlan_2g@2 { - label = "mamba:white:wlan_2g"; - reg = <0x2>; - }; - - wlan_5g@3 { - label = "mamba:white:wlan_5g"; - reg = <0x3>; - }; - - esata@4 { - label = "mamba:white:esata"; - reg = <0x4>; - linux,default-trigger = "disk-activity"; - }; - - usb2@5 { - label = "mamba:white:usb2"; - reg = <0x5>; - }; - - usb3_1@6 { - label = "mamba:white:usb3_1"; - reg = <0x6>; - }; - - usb3_2@7 { - label = "mamba:white:usb3_2"; - reg = <0x7>; - }; - - wps_white@8 { - label = "mamba:white:wps"; - reg = <0x8>; - }; - - wps_amber@9 { - label = "mamba:amber:wps"; - reg = <0x9>; - }; - }; - }; - - bm@c8000 { - status = "okay"; - }; - }; - - bm-bppi { - status = "okay"; - }; - }; - - gpio_keys { - compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-0 = <&keys_pin>; - pinctrl-names = "default"; - - wps { - label = "WPS"; - linux,code = <KEY_WPS_BUTTON>; - gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; - }; - - reset { - label = "Factory Reset Button"; - linux,code = <KEY_RESTART>; - gpios = <&gpio1 1 GPIO_ACTIVE_LOW>; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - pinctrl-0 = <&power_led_pin>; - pinctrl-names = "default"; - - power { - label = "mamba:white:power"; - gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; - default-state = "on"; - }; - }; - - pwm_fan { - /* SUNON HA4010V4-0000-C99 */ - - compatible = "pwm-fan"; - pwms = <&gpio0 24 4000>; - }; -}; - -&pciec { - status = "okay"; - - /* Etron EJ168 USB 3.0 controller */ - pcie@1,0 { - /* Port 0, Lane 0 */ - status = "okay"; - }; - - /* First mini-PCIe port */ - pcie@2,0 { - /* Port 0, Lane 1 */ - status = "okay"; - }; - - /* Second mini-PCIe port */ - pcie@3,0 { - /* Port 0, Lane 3 */ - status = "okay"; - }; -}; - -&pinctrl { - - keys_pin: keys-pin { - marvell,pins = "mpp32", "mpp33"; - marvell,function = "gpio"; - }; - - power_led_pin: power-led-pin { - marvell,pins = "mpp40"; - marvell,function = "gpio"; - }; - - gpio_fan_pin: gpio-fan-pin { - marvell,pins = "mpp24"; - marvell,function = "gpio"; - }; -}; - -&spi0 { - status = "okay"; - - spi-flash@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "everspin,mr25h256"; - reg = <0>; /* Chip select 0 */ - spi-max-frequency = <40000000>; - }; -}; - -&mdio { - status = "okay"; - - switch@0 { - compatible = "marvell,mv88e6085"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - label = "lan4"; - }; - - port@1 { - reg = <1>; - label = "lan3"; - }; - - port@2 { - reg = <2>; - label = "lan2"; - }; - - port@3 { - reg = <3>; - label = "lan1"; - }; - - port@4 { - reg = <4>; - label = "internet"; - }; - - port@5 { - reg = <5>; - label = "cpu"; - ethernet = <ð0>; - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; - }; -}; - -&nand_controller { - status = "okay"; - - nand@0 { - reg = <0>; - label = "pxa3xx_nand-0"; - nand-rb = <0>; - marvell,nand-keep-config; - nand-on-flash-bbt; - nand-ecc-strength = <4>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "u-boot"; - reg = <0x0000000 0x100000>; /* 1MB */ - read-only; - }; - - partition@100000 { - label = "u_env"; - reg = <0x100000 0x40000>; /* 256KB */ - }; - - partition@140000 { - label = "s_env"; - reg = <0x140000 0x40000>; /* 256KB */ - }; - - partition@900000 { - label = "devinfo"; - reg = <0x900000 0x100000>; /* 1MB */ - read-only; - }; - - /* kernel1 overlaps with rootfs1 by design */ - partition@a00000 { - label = "kernel1"; - reg = <0xa00000 0x2800000>; /* 40MB */ - }; - - partition@d00000 { - label = "rootfs1"; - reg = <0xd00000 0x2500000>; /* 37MB */ - }; - - /* kernel2 overlaps with rootfs2 by design */ - partition@3200000 { - label = "kernel2"; - reg = <0x3200000 0x2800000>; /* 40MB */ - }; - - partition@3500000 { - label = "rootfs2"; - reg = <0x3500000 0x2500000>; /* 37MB */ - }; - - /* - * 38MB, last MB is for the BBT, not writable - */ - partition@5a00000 { - label = "syscfg"; - reg = <0x5a00000 0x2600000>; - }; - - /* - * Unused area between "s_env" and "devinfo". - * Moved here because otherwise the renumbered - * partitions would break the bootloader - * supplied bootargs - */ - partition@180000 { - label = "unused_area"; - reg = <0x180000 0x780000>; /* 7.5MB */ - }; - }; - }; -}; |