diff options
Diffstat (limited to 'dts/src/arm/at91-wb50n.dtsi')
| -rw-r--r-- | dts/src/arm/at91-wb50n.dtsi | 198 |
1 files changed, 198 insertions, 0 deletions
diff --git a/dts/src/arm/at91-wb50n.dtsi b/dts/src/arm/at91-wb50n.dtsi new file mode 100644 index 0000000000..85692c8ef2 --- /dev/null +++ b/dts/src/arm/at91-wb50n.dtsi @@ -0,0 +1,198 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * at91-wb50n.dtsi - Device Tree include file for wb50n cpu module + * + * Copyright (C) 2018 Laird + * + */ + +#include "sama5d31.dtsi" + +/ { + model = "Laird Workgroup Bridge 50N - Atmel SAMA5D"; + compatible = "laird,wb50n", "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5"; + + chosen { + bootargs = "ubi.mtd=6 root=ubi0:rootfs rootfstype=ubifs rw"; + stdout-path = "serial0:115200n8"; + }; + + memory { + reg = <0x20000000 0x4000000>; + }; +}; + +&pinctrl { + board { + pinctrl_mmc0_cd: mmc0_cd { + atmel,pins = <AT91_PIOC 26 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PC26 GPIO with pullup deglitch */ + }; + + pinctrl_usba_vbus: usba_vbus { + atmel,pins = <AT91_PIOB 13 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PB13 GPIO with deglitch */ + }; + }; +}; + +&slow_xtal { + clock-frequency = <32768>; +}; + +&main_xtal { + clock-frequency = <12000000>; +}; + +&slow_osc { + atmel,osc-bypass; +}; + +&usart1_clk { + atmel,clk-output-range = <0 132000000>; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>; + cd-gpios = <&pioC 26 GPIO_ACTIVE_LOW>; + slot@0 { + reg = <0>; + bus-width = <4>; + }; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3>; + status = "okay"; + atheros@0 { + compatible = "atheros,ath6kl"; + atheros,board-id = "SD32"; + reg = <0>; + bus-width = <4>; + }; +}; + +&macb1 { + phy-mode = "rmii"; +}; + +&dbgu { + dmas = <0>, <0>; /* Do not use DMA for dbgu */ +}; + +/* On BB40 this port is labeled UART1 */ +&usart0 { + atmel,use-dma-rx; + atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart0 &pinctrl_usart0_rts_cts>; +}; + +/* On BB40 this port is labeled UART0 */ +&usart1 { + atmel,use-dma-rx; + atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>; + dtr-gpios = <&pioD 13 GPIO_ACTIVE_LOW>; + dsr-gpios = <&pioD 11 GPIO_ACTIVE_LOW>; + dcd-gpios = <&pioD 7 GPIO_ACTIVE_LOW>; + rng-gpios = <&pioD 8 GPIO_ACTIVE_LOW>; +}; + +/* USART3 is direct-connect to the Bluetooth UART on the radio SIP */ +&usart3 { + atmel,use-dma-rx; + atmel,use-dma-tx; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart3 &pinctrl_usart3_rts_cts>; + status = "okay"; +}; + +&spi1 { + cs-gpios = <&pioC 25 0>, <0>, <0>, <0>; +}; + +&ebi { + pinctrl-0 = <&pinctrl_ebi_nand_addr>; + pinctrl-names = "default"; + status = "okay"; +}; + +&nand_controller { + status = "okay"; + + nand: nand@3 { + reg = <0x3 0x0 0x2>; + atmel,rb = <0>; + nand-bus-width = <8>; + nand-ecc-mode = "hw"; + nand-ecc-strength = <8>; + nand-ecc-step-size = <512>; + nand-on-flash-bbt; + label = "atmel_nand"; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + at91bootstrap@0 { + label = "at91bs"; + reg = <0x0 0x20000>; + }; + + uboot@20000 { + label = "u-boot"; + reg = <0x20000 0x80000>; + }; + + ubootenv@a0000 { + label = "u-boot-env"; + reg = <0xa0000 0x20000>; + }; + + ubootenv@c0000 { + label = "u-boot-env"; + reg = <0xc0000 0x20000>; + }; + + kernel-a@e0000 { + label = "kernel-a"; + reg = <0xe0000 0x500000>; + }; + + kernel-b@5e0000 { + label = "kernel-b"; + reg = <0x5e0000 0x500000>; + }; + + rootfs-a@ae0000 { + label = "rootfs-a"; + reg = <0xae0000 0x3000000>; + }; + + rootfs-b@3ae0000 { + label = "rootfs-b"; + reg = <0x3ae0000 0x3000000>; + }; + + user@6ae0000 { + label = "user"; + reg = <0x6ae0000 0x14e0000>; + }; + }; + }; +}; + +&usb0 { + atmel,vbus-gpio = <&pioB 13 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usba_vbus>; +}; + +&usb1 { + num-ports = <3>; + atmel,vbus-gpio = <&pioA 2 GPIO_ACTIVE_LOW>; + atmel,oc-gpio = <&pioA 4 GPIO_ACTIVE_LOW>; +}; |