summaryrefslogtreecommitdiffstats
path: root/dts/src/arm/intel-ixp42x-freecom-fsg-3.dts
diff options
context:
space:
mode:
Diffstat (limited to 'dts/src/arm/intel-ixp42x-freecom-fsg-3.dts')
-rw-r--r--dts/src/arm/intel-ixp42x-freecom-fsg-3.dts158
1 files changed, 0 insertions, 158 deletions
diff --git a/dts/src/arm/intel-ixp42x-freecom-fsg-3.dts b/dts/src/arm/intel-ixp42x-freecom-fsg-3.dts
deleted file mode 100644
index 77e78c6dc2..0000000000
--- a/dts/src/arm/intel-ixp42x-freecom-fsg-3.dts
+++ /dev/null
@@ -1,158 +0,0 @@
-// SPDX-License-Identifier: ISC
-/*
- * Device Tree file for the Freecom FSG-3 router.
- * This machine is based on IXP425.
- * This device tree is inspired by the board file by Rod Whitby.
- */
-
-/dts-v1/;
-
-#include "intel-ixp42x.dtsi"
-#include <dt-bindings/input/input.h>
-
-/ {
- model = "Freecom FSG-3";
- compatible = "freecom,fsg-3", "intel,ixp42x";
- #address-cells = <1>;
- #size-cells = <1>;
-
- memory@0 {
- /* 64 MB memory */
- device_type = "memory";
- reg = <0x00000000 0x4000000>;
- };
-
- chosen {
- /* Boot from the first partition on the hard drive */
- bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootfstype=ext4 rootwait";
- stdout-path = "uart0:115200n8";
- };
-
- aliases {
- serial0 = &uart0;
- };
-
- gpio_keys {
- compatible = "gpio-keys";
-
- button-sync {
- wakeup-source;
- /* Closest approximation of what the key should do */
- linux,code = <KEY_CONNECT>;
- label = "sync";
- gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>;
- };
- button-reset {
- wakeup-source;
- linux,code = <KEY_ESC>;
- label = "reset";
- gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
- };
- button-usb {
- wakeup-source;
- /* Unplug USB, closest approximation of what the key should do */
- linux,code = <KEY_EJECTCD>;
- label = "usb";
- gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
- };
- };
-
- i2c {
- compatible = "i2c-gpio";
- sda-gpios = <&gpio0 12 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
- scl-gpios = <&gpio0 13 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- hwmon@28 {
- /*
- * Temperature sensor and fan control chip.
- *
- * TODO: create a proper device tree binding for
- * the sensor and temperature zone and create a
- * zone with fan control.
- */
- compatible = "winbond,w83781d";
- reg = <0x28>;
- };
- rtc@6f {
- compatible = "isil,isl1208";
- reg = <0x6f>;
- };
- };
-
- soc {
- bus@c4000000 {
- flash@0,0 {
- compatible = "intel,ixp4xx-flash", "cfi-flash";
- bank-width = <2>;
- /* Enable writes on the expansion bus */
- intel,ixp4xx-eb-write-enable = <1>;
- /* 4 MB of Flash mapped in at CS0 */
- reg = <0 0x00000000 0x400000>;
-
- partitions {
- compatible = "redboot-fis";
- /* Eraseblock at 0x3e0000 */
- fis-index-block = <0x1f>;
- };
- };
- };
-
- pci@c0000000 {
- status = "ok";
-
- /*
- * Written based on the FSG-3 PCI boardfile.
- * We have slots 12, 13 & 14 (IDSEL) with one IRQ each.
- */
- interrupt-map =
- /* IDSEL 12 */
- <0x6000 0 0 1 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 12 is irq 5 */
- <0x6000 0 0 2 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 12 is irq 5 */
- <0x6000 0 0 3 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 12 is irq 5 */
- <0x6000 0 0 4 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 12 is irq 5 */
- /* IDSEL 13 */
- <0x6800 0 0 1 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 13 is irq 7 */
- <0x6800 0 0 2 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 13 is irq 7 */
- <0x6800 0 0 3 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 13 is irq 7 */
- <0x6800 0 0 4 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 13 is irq 7 */
- /* IDSEL 14 */
- <0x7000 0 0 1 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 14 is irq 6 */
- <0x7000 0 0 2 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 14 is irq 6 */
- <0x7000 0 0 3 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 14 is irq 6 */
- <0x7000 0 0 4 &gpio0 6 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 14 is irq 6 */
- };
-
- /* EthB */
- ethernet@c8009000 {
- status = "ok";
- queue-rx = <&qmgr 3>;
- queue-txready = <&qmgr 20>;
- phy-mode = "rgmii";
- phy-handle = <&phy5>;
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy4: ethernet-phy@4 {
- reg = <4>;
- };
-
- phy5: ethernet-phy@5 {
- reg = <5>;
- };
- };
- };
-
- /* EthC */
- ethernet@c800a000 {
- status = "ok";
- queue-rx = <&qmgr 4>;
- queue-txready = <&qmgr 21>;
- phy-mode = "rgmii";
- phy-handle = <&phy4>;
- };
- };
-};