summaryrefslogtreecommitdiffstats
path: root/dts/src/arm/intel-ixp42x-ixdpg425.dts
diff options
context:
space:
mode:
Diffstat (limited to 'dts/src/arm/intel-ixp42x-ixdpg425.dts')
-rw-r--r--dts/src/arm/intel-ixp42x-ixdpg425.dts125
1 files changed, 125 insertions, 0 deletions
diff --git a/dts/src/arm/intel-ixp42x-ixdpg425.dts b/dts/src/arm/intel-ixp42x-ixdpg425.dts
new file mode 100644
index 0000000000..002a8705ab
--- /dev/null
+++ b/dts/src/arm/intel-ixp42x-ixdpg425.dts
@@ -0,0 +1,125 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for the Intel IXDPG425 reference design.
+ * Derived from boardfiles written by MontaVista software.
+ * Ethernet set-up from OpenWrt.
+ *
+ * The device has 4 x FXS RJ11 ports for analog phones for
+ * internet telephony. (Not supported yet.)
+ *
+ * The device has 9 status LEDs we do not support yet.
+ *
+ * This device is very similar to ADI engingeering Coyote.
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Intel IXDPG425 reference design";
+ compatible = "intel,ixdpg425", "intel,ixp42x";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ memory@0 {
+ /* 32 MB SDRAM */
+ device_type = "memory";
+ reg = <0x00000000 0x02000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootwait";
+ stdout-path = "uart0:115200n8";
+ };
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ soc {
+ bus@c4000000 {
+ flash@0,0 {
+ compatible = "intel,ixp4xx-flash", "cfi-flash";
+ bank-width = <2>;
+ /*
+ * CHECKME: the product brief says 16MB in a flash
+ * socket.
+ */
+ reg = <0 0x00000000 0x1000000>;
+
+ /* Configure expansion bus to allow writes */
+ intel,ixp4xx-eb-write-enable = <1>;
+
+ partitions {
+ compatible = "redboot-fis";
+ /* CHECKME: guess this is Redboot FIS */
+ fis-index-block = <0x7f>;
+ };
+ };
+ };
+
+ pci@c0000000 {
+ status = "ok";
+
+ /*
+ * Taken from IXDPG425 PCI boardfile.
+ * We have slots (IDSEL) 12, 13 and 14 with one assigned IRQ
+ * for 12 & 13 and one for 14.
+ */
+ interrupt-map =
+ /* IDSEL 12 */
+ <0x6000 0 0 1 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 12 is irq 7 */
+ <0x6000 0 0 2 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 12 is irq 7 */
+ <0x6000 0 0 3 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 12 is irq 7 */
+ <0x6000 0 0 4 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 12 is irq 7 */
+ /* IDSEL 13 */
+ <0x6800 0 0 1 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 13 is irq 7 */
+ <0x6800 0 0 2 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 13 is irq 7 */
+ <0x6800 0 0 3 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 13 is irq 7 */
+ <0x6800 0 0 4 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 13 is irq 7 */
+ /* IDSEL 14 */
+ <0x7000 0 0 1 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 14 is irq 6 */
+ <0x7000 0 0 2 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 14 is irq 6 */
+ <0x7000 0 0 3 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 14 is irq 6 */
+ <0x7000 0 0 4 &gpio0 6 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 14 is irq 6 */
+ };
+
+ /*
+ * CHECKME: this ethernet setup seems dubious. Photos of the board shows some kind
+ * of Realtek DSA switch on the board.
+ */
+
+ /* EthB */
+ ethernet@c8009000 {
+ status = "ok";
+ queue-rx = <&qmgr 3>;
+ queue-txready = <&qmgr 20>;
+ phy-mode = "rgmii";
+ phy-handle = <&phy5>;
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy4: ethernet-phy@4 {
+ reg = <4>;
+ };
+
+ phy5: ethernet-phy@5 {
+ reg = <5>;
+ };
+ };
+ };
+
+ /* EthC */
+ ethernet@c800a000 {
+ status = "ok";
+ queue-rx = <&qmgr 4>;
+ queue-txready = <&qmgr 21>;
+ phy-mode = "rgmii";
+ phy-handle = <&phy4>;
+ };
+ };
+};