1 files changed, 0 insertions, 116 deletions
diff --git a/dts/src/arm/mmp3-dell-ariel.dts b/dts/src/arm/mmp3-dell-ariel.dts
deleted file mode 100644
index b0ec14c421..0000000000
--- a/dts/src/arm/mmp3-dell-ariel.dts
+++ /dev/null
@@ -1,116 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-/*
- * Dell Wyse 3020 a.k.a. "Ariel" a.k.a. Tx0D (T00D, T10D)
- *
- * Copyright (C) 2019 Lubomir Rintel <lkundrak@v3.sk>
- */
-
-/dts-v1/;
-#include "mmp3.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-
-/ {
-	model = "Dell Ariel";
-	compatible = "dell,wyse-ariel", "marvell,mmp3";
-
-	aliases {
-		serial2 = &uart3;
-	};
-
-	chosen {
-		#address-cells = <0x1>;
-		#size-cells = <0x1>;
-		ranges;
-		bootargs = "earlyprintk=ttyS2,115200 console=ttyS2,115200";
-	};
-
-	memory@0 {
-		linux,usable-memory = <0x0 0x7f600000>;
-		available = <0x7f700000 0x7ff00000 0x00000000 0x7f600000>;
-		reg = <0x0 0x80000000>;
-		device_type = "memory";
-	};
-};
-
-&uart3 {
-	status = "okay";
-};
-
-&rtc {
-	status = "okay";
-};
-
-&usb_otg0 {
-	status = "okay";
-};
-
-&usb_otg_phy0 {
-	status = "okay";
-};
-
-&hsic0 {
-	status = "okay";
-
-	usb1@1 {
-		compatible = "usb424,2640";
-		reg = <0x01>;
-		#address-cells = <0x01>;
-		#size-cells = <0x00>;
-
-		mass-storage@1 {
-			compatible = "usb424,4040";
-			reg = <0x01>;
-			status = "disabled";
-		};
-	};
-};
-
-&hsic_phy0 {
-	status = "okay";
-	reset-gpios = <&gpio 63 GPIO_ACTIVE_HIGH>;
-};
-
-&mmc3 {
-	status = "okay";
-	max-frequency = <50000000>;
-	status = "okay";
-	bus-width = <8>;
-	non-removable;
-	cap-mmc-highspeed;
-};
-
-&twsi1 {
-	status = "okay";
-
-	rtc@68 {
-		compatible = "dallas,ds1338";
-		reg = <0x68>;
-		status = "okay";
-	};
-};
-
-&twsi3 {
-	status = "okay";
-};
-
-&twsi4 {
-	status = "okay";
-};
-
-&ssp1 {
-	status = "okay";
-	cs-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
-
-	firmware-flash@0 {
-		compatible = "winbond,w25q32", "jedec,spi-nor";
-		reg = <0>;
-		spi-max-frequency = <104000000>;
-		m25p,fast-read;
-	};
-};
-
-&ssp2 {
-	cs-gpios = <&gpio 56 GPIO_ACTIVE_LOW>;
-	status = "okay";
-};