diff options
Diffstat (limited to 'dts/src/arm/omap5-cm-t54.dts')
| -rw-r--r-- | dts/src/arm/omap5-cm-t54.dts | 413 |
1 files changed, 413 insertions, 0 deletions
diff --git a/dts/src/arm/omap5-cm-t54.dts b/dts/src/arm/omap5-cm-t54.dts new file mode 100644 index 0000000000..b8698ca686 --- /dev/null +++ b/dts/src/arm/omap5-cm-t54.dts @@ -0,0 +1,413 @@ +/* + * Support for CompuLab CM-T54 + */ +/dts-v1/; + +#include "omap5.dtsi" +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> + +/ { + model = "CompuLab CM-T54"; + compatible = "compulab,omap5-cm-t54", "ti,omap5"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x7F000000>; /* 2048 MB */ + }; + + vmmcsd_fixed: fixed-regulator-mmcsd { + compatible = "regulator-fixed"; + regulator-name = "vmmcsd_fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + vwlan_pdn_fixed: fixed-regulator-vwlan-pdn { + compatible = "regulator-fixed"; + regulator-name = "vwlan_pdn_fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&ldo2_reg>; + gpio = <&gpio4 13 GPIO_ACTIVE_HIGH>; /* gpio4_109 */ + startup-delay-us = <1000>; + enable-active-high; + }; + + vwlan_fixed: fixed-regulator-vwlan { + compatible = "regulator-fixed"; + regulator-name = "vwlan_fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vwlan_pdn_fixed>; + gpio = <&gpio4 14 GPIO_ACTIVE_HIGH>; /* gpio4_110 */ + startup-delay-us = <1000>; + enable-active-high; + }; + + /* HS USB Host PHY on PORT 2 */ + hsusb2_phy: hsusb2_phy { + compatible = "usb-nop-xceiv"; + reset-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>; /* gpio3_76 HUB_RESET */ + }; + + /* HS USB Host PHY on PORT 3 */ + hsusb3_phy: hsusb3_phy { + compatible = "usb-nop-xceiv"; + reset-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; /* gpio3_83 ETH_RESET */ + }; + + leds { + compatible = "gpio-leds"; + led@1 { + label = "Heartbeat"; + gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>; /* gpio3_80 ACT_LED */ + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + }; +}; + +&omap5_pmx_core { + pinctrl-names = "default"; + pinctrl-0 = < + &led_gpio_pins + &usbhost_pins + >; + + led_gpio_pins: pinmux_led_gpio_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x00b0, PIN_OUTPUT | MUX_MODE6) /* hsi2_caflag.gpio3_80 */ + >; + }; + + i2c1_pins: pinmux_i2c1_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x01f2, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_pmic_scl */ + OMAP5_IOPAD(0x01f4, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_pmic_sda */ + >; + }; + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x01e2, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_clk */ + OMAP5_IOPAD(0x01e4, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_cmd */ + OMAP5_IOPAD(0x01e6, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data2 */ + OMAP5_IOPAD(0x01e8, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data3 */ + OMAP5_IOPAD(0x01ea, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data0 */ + OMAP5_IOPAD(0x01ec, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data1 */ + >; + }; + + mmc2_pins: pinmux_mmc2_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x0040, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_clk */ + OMAP5_IOPAD(0x0042, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_cmd */ + OMAP5_IOPAD(0x0044, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data0 */ + OMAP5_IOPAD(0x0046, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data1 */ + OMAP5_IOPAD(0x0048, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data2 */ + OMAP5_IOPAD(0x004a, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data3 */ + OMAP5_IOPAD(0x004c, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data4 */ + OMAP5_IOPAD(0x004e, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data5 */ + OMAP5_IOPAD(0x0050, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data6 */ + OMAP5_IOPAD(0x0052, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data7 */ + >; + }; + + mmc3_pins: pinmux_mmc3_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x01a4, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_clk */ + OMAP5_IOPAD(0x01a6, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_cmd */ + OMAP5_IOPAD(0x01a8, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data0 */ + OMAP5_IOPAD(0x01aa, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data1 */ + OMAP5_IOPAD(0x01ac, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data2 */ + OMAP5_IOPAD(0x01ae, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data3 */ + >; + }; + + wlan_gpios_pins: pinmux_wlan_gpios_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x019c, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* gpio4_109 */ + OMAP5_IOPAD(0x019e, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* gpio4_110 */ + >; + }; + + usbhost_pins: pinmux_usbhost_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x00c4, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */ + OMAP5_IOPAD(0x00c6, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_data */ + + OMAP5_IOPAD(0x01dc, PIN_INPUT | MUX_MODE0) /* usbb3_hsic_strobe */ + OMAP5_IOPAD(0x01de, PIN_INPUT | MUX_MODE0) /* usbb3_hsic_data */ + + OMAP5_IOPAD(0x00a8, PIN_OUTPUT | MUX_MODE6) /* hsi2_caready.gpio3_76 */ + OMAP5_IOPAD(0x00b6, PIN_OUTPUT | MUX_MODE6) /* hsi2_acdata.gpio3_83 */ + >; + }; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + vmmc-supply = <&ldo9_reg>; + bus-width = <4>; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>; + vmmc-supply = <&vmmcsd_fixed>; + bus-width = <8>; + ti,non-removable; +}; + +&mmc3 { + pinctrl-names = "default"; + pinctrl-0 = < + &mmc3_pins + &wlan_gpios_pins + >; + vmmc-supply = <&vwlan_fixed>; + bus-width = <4>; + ti,non-removable; +}; + +&mmc4 { + status = "disabled"; +}; + +&mmc5 { + status = "disabled"; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + + clock-frequency = <400000>; + + at24@50 { + compatible = "at24,24c02"; + pagesize = <16>; + reg = <0x50>; + }; + + palmas: palmas@48 { + compatible = "ti,palmas"; + interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */ + interrupt-parent = <&gic>; + reg = <0x48>; + interrupt-controller; + #interrupt-cells = <2>; + ti,system-power-controller; + + extcon_usb3: palmas_usb { + compatible = "ti,palmas-usb-vid"; + ti,enable-vbus-detection; + ti,enable-id-detection; + ti,wakeup; + }; + + rtc { + compatible = "ti,palmas-rtc"; + interrupt-parent = <&palmas>; + interrupts = <8 IRQ_TYPE_NONE>; + }; + + palmas_pmic { + compatible = "ti,palmas-pmic"; + interrupt-parent = <&palmas>; + interrupts = <14 IRQ_TYPE_NONE>; + interrupt-name = "short-irq"; + + ti,ldo6-vibrator; + + regulators { + smps123_reg: smps123 { + /* VDD_OPP_MPU */ + regulator-name = "smps123"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + }; + + smps45_reg: smps45 { + /* VDD_OPP_MM */ + regulator-name = "smps45"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1310000>; + regulator-always-on; + regulator-boot-on; + }; + + smps6_reg: smps6 { + /* VDD_DDR3 - over VDD_SMPS6 */ + regulator-name = "smps6"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + }; + + smps7_reg: smps7 { + /* VDDS_1v8_OMAP over VDDS_1v8_MAIN */ + regulator-name = "smps7"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + smps8_reg: smps8 { + /* VDD_OPP_CORE */ + regulator-name = "smps8"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1310000>; + regulator-always-on; + regulator-boot-on; + }; + + smps9_reg: smps9 { + /* VDDA_2v1_AUD over VDD_2v1 */ + regulator-name = "smps9"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + ti,smps-range = <0x80>; + regulator-always-on; + regulator-boot-on; + }; + + smps10_out2_reg: smps10_out2 { + /* VBUS_5V_OTG */ + regulator-name = "smps10_out2"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; + + smps10_out1_reg: smps10_out1 { + /* VBUS_5V_OTG */ + regulator-name = "smps10_out1"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + ldo1_reg: ldo1 { + /* VDDAPHY_CAM: vdda_csiport */ + regulator-name = "ldo1"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1800000>; + }; + + ldo2_reg: ldo2 { + /* VDD_3V3_WLAN */ + regulator-name = "ldo2"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + startup-delay-us = <1000>; + }; + + ldo3_reg: ldo3 { + /* VCC_1V5_AUD */ + regulator-name = "ldo3"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo4_reg: ldo4 { + /* VDDAPHY_DISP: vdda_dsiport/hdmi */ + regulator-name = "ldo4"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1800000>; + }; + + ldo5_reg: ldo5 { + /* VDDA_1V8_PHY: usb/sata/hdmi.. */ + regulator-name = "ldo5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo6_reg: ldo6 { + /* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */ + regulator-name = "ldo6"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo7_reg: ldo7 { + /* VDD_VPP: vpp1 */ + regulator-name = "ldo7"; + regulator-min-microvolt = <2000000>; + regulator-max-microvolt = <2000000>; + /* Only for efuse reprograming! */ + status = "disabled"; + }; + + ldo8_reg: ldo8 { + /* VDD_3v0: Does not go anywhere */ + regulator-name = "ldo8"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + /* Unused */ + status = "disabled"; + }; + + ldo9_reg: ldo9 { + /* VCC_DV_SDIO: vdds_sdcard */ + regulator-name = "ldo9"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + }; + + ldoln_reg: ldoln { + /* VDDA_1v8_REF: vdds_osc/mm_l4per.. */ + regulator-name = "ldoln"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldousb_reg: ldousb { + /* VDDA_3V_USB: VDDA_USBHS33 */ + regulator-name = "ldousb"; + regulator-min-microvolt = <3250000>; + regulator-max-microvolt = <3250000>; + regulator-always-on; + regulator-boot-on; + }; + + regen3_reg: regen3 { + /* REGEN3 controls LDO9 supply to card */ + regulator-name = "regen3"; + regulator-always-on; + regulator-boot-on; + }; + }; + }; + }; +}; + +&usbhshost { + port2-mode = "ehci-hsic"; + port3-mode = "ehci-hsic"; +}; + +&usbhsehci { + phys = <0 &hsusb2_phy &hsusb3_phy>; +}; + +&cpu0 { + cpu0-supply = <&smps123_reg>; +}; |