diff options
Diffstat (limited to 'dts/src/arm/omap5.dtsi')
| -rw-r--r-- | dts/src/arm/omap5.dtsi | 475 |
1 files changed, 0 insertions, 475 deletions
diff --git a/dts/src/arm/omap5.dtsi b/dts/src/arm/omap5.dtsi deleted file mode 100644 index d0ecf54d5a..0000000000 --- a/dts/src/arm/omap5.dtsi +++ /dev/null @@ -1,475 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-only -/* - * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ - * - * Based on "omap4.dtsi" - */ - -#include <dt-bindings/bus/ti-sysc.h> -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/interrupt-controller/arm-gic.h> -#include <dt-bindings/pinctrl/omap.h> -#include <dt-bindings/clock/omap5.h> - -/ { - #address-cells = <2>; - #size-cells = <2>; - - compatible = "ti,omap5"; - interrupt-parent = <&wakeupgen>; - chosen { }; - - aliases { - i2c0 = &i2c1; - i2c1 = &i2c2; - i2c2 = &i2c3; - i2c3 = &i2c4; - i2c4 = &i2c5; - serial0 = &uart1; - serial1 = &uart2; - serial2 = &uart3; - serial3 = &uart4; - serial4 = &uart5; - serial5 = &uart6; - }; - - cpus { - #address-cells = <1>; - #size-cells = <0>; - - cpu0: cpu@0 { - device_type = "cpu"; - compatible = "arm,cortex-a15"; - reg = <0x0>; - - operating-points = < - /* kHz uV */ - 1000000 1060000 - 1500000 1250000 - >; - - clocks = <&dpll_mpu_ck>; - clock-names = "cpu"; - - clock-latency = <300000>; /* From omap-cpufreq driver */ - - /* cooling options */ - #cooling-cells = <2>; /* min followed by max */ - }; - cpu@1 { - device_type = "cpu"; - compatible = "arm,cortex-a15"; - reg = <0x1>; - - operating-points = < - /* kHz uV */ - 1000000 1060000 - 1500000 1250000 - >; - - clocks = <&dpll_mpu_ck>; - clock-names = "cpu"; - - clock-latency = <300000>; /* From omap-cpufreq driver */ - - /* cooling options */ - #cooling-cells = <2>; /* min followed by max */ - }; - }; - - thermal-zones { - #include "omap4-cpu-thermal.dtsi" - #include "omap5-gpu-thermal.dtsi" - #include "omap5-core-thermal.dtsi" - }; - - timer { - compatible = "arm,armv7-timer"; - /* PPI secure/nonsecure IRQ */ - interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>, - <GIC_PPI 14 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>, - <GIC_PPI 11 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>, - <GIC_PPI 10 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>; - interrupt-parent = <&gic>; - }; - - pmu { - compatible = "arm,cortex-a15-pmu"; - interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>; - }; - - gic: interrupt-controller@48211000 { - compatible = "arm,cortex-a15-gic"; - interrupt-controller; - #interrupt-cells = <3>; - reg = <0 0x48211000 0 0x1000>, - <0 0x48212000 0 0x2000>, - <0 0x48214000 0 0x2000>, - <0 0x48216000 0 0x2000>; - interrupt-parent = <&gic>; - }; - - wakeupgen: interrupt-controller@48281000 { - compatible = "ti,omap5-wugen-mpu", "ti,omap4-wugen-mpu"; - interrupt-controller; - #interrupt-cells = <3>; - reg = <0 0x48281000 0 0x1000>; - interrupt-parent = <&gic>; - }; - - /* - * The soc node represents the soc top level view. It is used for IPs - * that are not memory mapped in the MPU view or for the MPU itself. - */ - soc { - compatible = "ti,omap-infra"; - mpu { - compatible = "ti,omap4-mpu"; - ti,hwmods = "mpu"; - sram = <&ocmcram>; - }; - }; - - /* - * XXX: Use a flat representation of the OMAP3 interconnect. - * The real OMAP interconnect network is quite complex. - * Since it will not bring real advantage to represent that in DT for - * the moment, just use a fake OCP bus entry to represent the whole bus - * hierarchy. - */ - ocp { - compatible = "ti,omap5-l3-noc", "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0 0 0 0xc0000000>; - ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3"; - reg = <0 0x44000000 0 0x2000>, - <0 0x44800000 0 0x3000>, - <0 0x45000000 0 0x4000>; - interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; - - l4_wkup: interconnect@4ae00000 { - }; - - l4_cfg: interconnect@4a000000 { - }; - - l4_per: interconnect@48000000 { - }; - - l4_abe: interconnect@40100000 { - }; - - ocmcram: sram@40300000 { - compatible = "mmio-sram"; - reg = <0x40300000 0x20000>; /* 128k */ - }; - - gpmc: gpmc@50000000 { - compatible = "ti,omap4430-gpmc"; - reg = <0x50000000 0x1000>; - #address-cells = <2>; - #size-cells = <1>; - interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; - dmas = <&sdma 4>; - dma-names = "rxtx"; - gpmc,num-cs = <8>; - gpmc,num-waitpins = <4>; - ti,hwmods = "gpmc"; - clocks = <&l3_iclk_div>; - clock-names = "fck"; - interrupt-controller; - #interrupt-cells = <2>; - gpio-controller; - #gpio-cells = <2>; - }; - - target-module@55082000 { - compatible = "ti,sysc-omap2", "ti,sysc"; - reg = <0x55082000 0x4>, - <0x55082010 0x4>, - <0x55082014 0x4>; - reg-names = "rev", "sysc", "syss"; - ti,sysc-sidle = <SYSC_IDLE_FORCE>, - <SYSC_IDLE_NO>, - <SYSC_IDLE_SMART>; - ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY | - SYSC_OMAP2_SOFTRESET | - SYSC_OMAP2_AUTOIDLE)>; - clocks = <&ipu_clkctrl OMAP5_MMU_IPU_CLKCTRL 0>; - clock-names = "fck"; - resets = <&prm_core 2>; - reset-names = "rstctrl"; - ranges = <0x0 0x55082000 0x100>; - #size-cells = <1>; - #address-cells = <1>; - - mmu_ipu: mmu@0 { - compatible = "ti,omap4-iommu"; - reg = <0x0 0x100>; - interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; - #iommu-cells = <0>; - ti,iommu-bus-err-back; - }; - }; - - dmm@4e000000 { - compatible = "ti,omap5-dmm"; - reg = <0x4e000000 0x800>; - interrupts = <0 113 0x4>; - ti,hwmods = "dmm"; - }; - - emif1: emif@4c000000 { - compatible = "ti,emif-4d5"; - ti,hwmods = "emif1"; - ti,no-idle-on-init; - phy-type = <2>; /* DDR PHY type: Intelli PHY */ - reg = <0x4c000000 0x400>; - interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; - hw-caps-read-idle-ctrl; - hw-caps-ll-interface; - hw-caps-temp-alert; - }; - - emif2: emif@4d000000 { - compatible = "ti,emif-4d5"; - ti,hwmods = "emif2"; - ti,no-idle-on-init; - phy-type = <2>; /* DDR PHY type: Intelli PHY */ - reg = <0x4d000000 0x400>; - interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; - hw-caps-read-idle-ctrl; - hw-caps-ll-interface; - hw-caps-temp-alert; - }; - - bandgap: bandgap@4a0021e0 { - reg = <0x4a0021e0 0xc - 0x4a00232c 0xc - 0x4a002380 0x2c - 0x4a0023C0 0x3c>; - interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; - compatible = "ti,omap5430-bandgap"; - - #thermal-sensor-cells = <1>; - }; - - /* OCP2SCP3 */ - sata: sata@4a141100 { - compatible = "snps,dwc-ahci"; - reg = <0x4a140000 0x1100>, <0x4a141100 0x7>; - interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>; - phys = <&sata_phy>; - phy-names = "sata-phy"; - clocks = <&l3init_clkctrl OMAP5_SATA_CLKCTRL 8>; - ti,hwmods = "sata"; - ports-implemented = <0x1>; - }; - - target-module@56000000 { - compatible = "ti,sysc-omap4", "ti,sysc"; - reg = <0x5600fe00 0x4>, - <0x5600fe10 0x4>; - reg-names = "rev", "sysc"; - ti,sysc-midle = <SYSC_IDLE_FORCE>, - <SYSC_IDLE_NO>, - <SYSC_IDLE_SMART>; - ti,sysc-sidle = <SYSC_IDLE_FORCE>, - <SYSC_IDLE_NO>, - <SYSC_IDLE_SMART>; - clocks = <&gpu_clkctrl OMAP5_GPU_CLKCTRL 0>; - clock-names = "fck"; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0 0x56000000 0x2000000>; - - /* - * Closed source PowerVR driver, no child device - * binding or driver in mainline - */ - }; - - dss: dss@58000000 { - compatible = "ti,omap5-dss"; - reg = <0x58000000 0x80>; - status = "disabled"; - ti,hwmods = "dss_core"; - clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 8>; - clock-names = "fck"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - - dispc@58001000 { - compatible = "ti,omap5-dispc"; - reg = <0x58001000 0x1000>; - interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; - ti,hwmods = "dss_dispc"; - clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 8>; - clock-names = "fck"; - }; - - rfbi: encoder@58002000 { - compatible = "ti,omap5-rfbi"; - reg = <0x58002000 0x100>; - status = "disabled"; - ti,hwmods = "dss_rfbi"; - clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 8>, <&l3_iclk_div>; - clock-names = "fck", "ick"; - }; - - dsi1: encoder@58004000 { - compatible = "ti,omap5-dsi"; - reg = <0x58004000 0x200>, - <0x58004200 0x40>, - <0x58004300 0x40>; - reg-names = "proto", "phy", "pll"; - interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; - status = "disabled"; - ti,hwmods = "dss_dsi1"; - clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 8>, - <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 10>; - clock-names = "fck", "sys_clk"; - }; - - dsi2: encoder@58005000 { - compatible = "ti,omap5-dsi"; - reg = <0x58009000 0x200>, - <0x58009200 0x40>, - <0x58009300 0x40>; - reg-names = "proto", "phy", "pll"; - interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; - status = "disabled"; - ti,hwmods = "dss_dsi2"; - clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 8>, - <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 10>; - clock-names = "fck", "sys_clk"; - }; - - hdmi: encoder@58060000 { - compatible = "ti,omap5-hdmi"; - reg = <0x58040000 0x200>, - <0x58040200 0x80>, - <0x58040300 0x80>, - <0x58060000 0x19000>; - reg-names = "wp", "pll", "phy", "core"; - interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; - status = "disabled"; - ti,hwmods = "dss_hdmi"; - clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 9>, - <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 10>; - clock-names = "fck", "sys_clk"; - dmas = <&sdma 76>; - dma-names = "audio_tx"; - }; - }; - - abb_mpu: regulator-abb-mpu { - compatible = "ti,abb-v2"; - regulator-name = "abb_mpu"; - #address-cells = <0>; - #size-cells = <0>; - clocks = <&sys_clkin>; - ti,settling-time = <50>; - ti,clock-cycles = <16>; - - reg = <0x4ae07cdc 0x8>, <0x4ae06014 0x4>, - <0x4a0021c4 0x8>, <0x4ae0c318 0x4>; - reg-names = "base-address", "int-address", - "efuse-address", "ldo-address"; - ti,tranxdone-status-mask = <0x80>; - /* LDOVBBMPU_MUX_CTRL */ - ti,ldovbb-override-mask = <0x400>; - /* LDOVBBMPU_VSET_OUT */ - ti,ldovbb-vset-mask = <0x1F>; - - /* - * NOTE: only FBB mode used but actual vset will - * determine final biasing - */ - ti,abb_info = < - /*uV ABB efuse rbb_m fbb_m vset_m*/ - 1060000 0 0x0 0 0x02000000 0x01F00000 - 1250000 0 0x4 0 0x02000000 0x01F00000 - >; - }; - - abb_mm: regulator-abb-mm { - compatible = "ti,abb-v2"; - regulator-name = "abb_mm"; - #address-cells = <0>; - #size-cells = <0>; - clocks = <&sys_clkin>; - ti,settling-time = <50>; - ti,clock-cycles = <16>; - - reg = <0x4ae07ce4 0x8>, <0x4ae06010 0x4>, - <0x4a0021a4 0x8>, <0x4ae0c314 0x4>; - reg-names = "base-address", "int-address", - "efuse-address", "ldo-address"; - ti,tranxdone-status-mask = <0x80000000>; - /* LDOVBBMM_MUX_CTRL */ - ti,ldovbb-override-mask = <0x400>; - /* LDOVBBMM_VSET_OUT */ - ti,ldovbb-vset-mask = <0x1F>; - - /* - * NOTE: only FBB mode used but actual vset will - * determine final biasing - */ - ti,abb_info = < - /*uV ABB efuse rbb_m fbb_m vset_m*/ - 1025000 0 0x0 0 0x02000000 0x01F00000 - 1120000 0 0x4 0 0x02000000 0x01F00000 - >; - }; - }; -}; - -&cpu_thermal { - polling-delay = <500>; /* milliseconds */ - coefficients = <65 (-1791)>; -}; - -#include "omap5-l4.dtsi" -#include "omap54xx-clocks.dtsi" - -&gpu_thermal { - coefficients = <117 (-2992)>; -}; - -&core_thermal { - coefficients = <0 2000>; -}; - -#include "omap5-l4-abe.dtsi" -#include "omap54xx-clocks.dtsi" - -&prm { - prm_dsp: prm@400 { - compatible = "ti,omap5-prm-inst", "ti,omap-prm-inst"; - reg = <0x400 0x100>; - #reset-cells = <1>; - }; - - prm_core: prm@700 { - compatible = "ti,omap5-prm-inst", "ti,omap-prm-inst"; - reg = <0x700 0x100>; - #reset-cells = <1>; - }; - - prm_iva: prm@1200 { - compatible = "ti,omap5-prm-inst", "ti,omap-prm-inst"; - reg = <0x1200 0x100>; - #reset-cells = <1>; - }; - - prm_device: prm@1c00 { - compatible = "ti,omap5-prm-inst", "ti,omap-prm-inst"; - reg = <0x1c00 0x100>; - #reset-cells = <1>; - }; -}; |