diff options
Diffstat (limited to 'dts/src/arm/qcom-mdm9615-wp8548-mangoh-green.dts')
| -rw-r--r-- | dts/src/arm/qcom-mdm9615-wp8548-mangoh-green.dts | 281 |
1 files changed, 0 insertions, 281 deletions
diff --git a/dts/src/arm/qcom-mdm9615-wp8548-mangoh-green.dts b/dts/src/arm/qcom-mdm9615-wp8548-mangoh-green.dts deleted file mode 100644 index 942e3a2cac..0000000000 --- a/dts/src/arm/qcom-mdm9615-wp8548-mangoh-green.dts +++ /dev/null @@ -1,281 +0,0 @@ -/* - * Device Tree Source for mangOH Green Board with WP8548 Module - * - * Copyright (C) 2016 BayLibre, SAS. - * Author : Neil Armstrong <narmstrong@baylibre.com> - * - * This file is dual-licensed: you can use it either under the terms - * of the GPL or the X11 license, at your option. Note that this dual - * licensing only applies to this file, and not this project as a - * whole. - * - * a) This file is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of the - * License, or (at your option) any later version. - * - * This file is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * Or, alternatively, - * - * b) Permission is hereby granted, free of charge, to any person - * obtaining a copy of this software and associated documentation - * files (the "Software"), to deal in the Software without - * restriction, including without limitation the rights to use, - * copy, modify, merge, publish, distribute, sublicense, and/or - * sell copies of the Software, and to permit persons to whom the - * Software is furnished to do so, subject to the following - * conditions: - * - * The above copyright notice and this permission notice shall be - * included in all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES - * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT - * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, - * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR - * OTHER DEALINGS IN THE SOFTWARE. - */ - -#include <dt-bindings/input/input.h> - -#include "qcom-mdm9615-wp8548.dtsi" -#include <dt-bindings/interrupt-controller/irq.h> -#include <dt-bindings/gpio/gpio.h> - -/ { - model = "MangOH Green with WP8548 Module"; - compatible = "swir,mangoh-green-wp8548", "swir,wp8548", "qcom,mdm9615"; - - aliases { - spi0 = &gsbi3_spi; - serial0 = &gsbi4_serial; - serial1 = &gsbi5_serial; - i2c0 = &gsbi5_i2c; - mmc0 = &sdcc1; - }; - - chosen { - stdout-path = "serial1:115200n8"; - }; -}; - -&msmgpio { - /* MangOH GPIO Mapping : - * - 2 : GPIOEXP_INT2 - * - 7 : IOT1_GPIO2 - * - 8 : IOT0_GPIO4 - * - 13: IOT0_GPIO3 - * - 21: IOT1_GPIO4 - * - 22: IOT2_GPIO1 - * - 23: IOT2_GPIO2 - * - 24: IOT2_GPIO3 - * - 25: IOT1_GPIO1 - * - 32: IOT1_GPIO3 - * - 33: IOT0_GPIO2 - * - 42: IOT0_GPIO1 and SD Card Detect - */ - - gpioext1_pins: gpioext1_pins { - pins { - pins = "gpio2"; - function = "gpio"; - input-enable; - bias-disable; - }; - }; - - sdc_cd_pins: sdc_cd_pins { - pins { - pins = "gpio42"; - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; - }; -}; - -&gsbi3_spi { - spi@0 { - compatible = "swir,mangoh-iotport-spi", "spidev"; - spi-max-frequency = <24000000>; - reg = <0>; - }; -}; - -&gsbi5_i2c { - mux@71 { - compatible = "nxp,pca9548"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x71>; - - i2c_iot0: i2c@0 { - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - }; - - i2c_iot1: i2c@1 { - #address-cells = <1>; - #size-cells = <0>; - reg = <1>; - }; - - i2c_iot2: i2c@2 { - #address-cells = <1>; - #size-cells = <0>; - reg = <2>; - }; - - i2c@3 { - #address-cells = <1>; - #size-cells = <0>; - reg = <3>; - - usbhub: hub@8 { - compatible = "smsc,usb3503a"; - reg = <0x8>; - connect-gpios = <&gpioext2 1 GPIO_ACTIVE_HIGH>; - intn-gpios = <&gpioext2 0 GPIO_ACTIVE_HIGH>; - initial-mode = <1>; - }; - }; - - i2c@4 { - #address-cells = <1>; - #size-cells = <0>; - reg = <4>; - - gpioext0: gpio@3e { - /* GPIO Expander 0 Mapping : - * - 0: ARDUINO_RESET_Level shift - * - 1: BattChrgr_PG_N - * - 2: BattGauge_GPIO - * - 3: LED_ON (out active high) - * - 4: ATmega_reset_GPIO - * - 5: X - * - 6: PCM_ANALOG_SELECT (out active high) - * - 7: X - * - 8: Board_rev_res1 (in) - * - 9: Board_rev_res2 (in) - * - 10: UART_EXP1_ENn (out active low / pull-down) - * - 11: UART_EXP1_IN (out pull-down) - * - 12: UART_EXP2_IN (out pull-down) - * - 13: SDIO_SEL (out pull-down) - * - 14: SPI_EXP1_ENn (out active low / pull-down) - * - 15: SPI_EXP1_IN (out pull-down) - */ - #gpio-cells = <2>; - #interrupt-cells = <2>; - compatible = "semtech,sx1509q"; - reg = <0x3e>; - interrupt-parent = <&gpioext1>; - interrupts = <0 IRQ_TYPE_EDGE_FALLING>; - - probe-reset; - - gpio-controller; - interrupt-controller; - }; - }; - - i2c@5 { - #address-cells = <1>; - #size-cells = <0>; - reg = <5>; - - gpioext1: gpio@3f { - /* GPIO Expander 1 Mapping : - * - 0: GPIOEXP_INT1 - * - 1: Battery detect - * - 2: GPIO_SCF3_RESET - * - 3: LED_CARD_DETECT_IOT0 (in) - * - 4: LED_CARD_DETECT_IOT1 (in) - * - 5: LED_CARD_DETECT_IOT2 (in) - * - 6: UIM2_PWM_SELECT - * - 7: UIM2_M2_S_SELECT - * - 8: TP900 - * - 9: SENSOR_INT1 (in) - * - 10: SENSOR_INT2 (in) - * - 11: CARD_DETECT_IOT0 (in pull-up) - * - 12: CARD_DETECT_IOT2 (in pull-up) - * - 13: CARD_DETECT_IOT1 (in pull-up) - * - 14: GPIOEXP_INT3 (in active low / pull-up) - * - 15: BattChrgr_INT_N - */ - pinctrl-0 = <&gpioext1_pins>; - pinctrl-names = "default"; - - #gpio-cells = <2>; - #interrupt-cells = <2>; - compatible = "semtech,sx1509q"; - reg = <0x3f>; - interrupt-parent = <&msmgpio>; - interrupts = <0 IRQ_TYPE_EDGE_FALLING>; - - probe-reset; - - gpio-controller; - interrupt-controller; - }; - }; - - i2c@6 { - #address-cells = <1>; - #size-cells = <0>; - reg = <6>; - - gpioext2: gpio@70 { - /* GPIO Expander 2 Mapping : - * - 0: USB_HUB_INTn - * - 1: HUB_CONNECT - * - 2: GPIO_IOT2_RESET (out active low / pull-up) - * - 3: GPIO_IOT1_RESET (out active low / pull-up) - * - 4: GPIO_IOT0_RESET (out active low / pull-up) - * - 5: TP901 - * - 6: TP902 - * - 7: TP903 - * - 8: UART_EXP2_ENn (out active low / pull-down) - * - 9: PCM_EXP1_ENn (out active low) - * - 10: PCM_EXP1_SEL (out) - * - 11: ARD_FTDI - * - 12: TP904 - * - 13: TP905 - * - 14: TP906 - * - 15: RS232_Enable (out active high / pull-up) - */ - #gpio-cells = <2>; - #interrupt-cells = <2>; - compatible = "semtech,sx1509q"; - reg = <0x70>; - interrupt-parent = <&gpioext1>; - interrupts = <14 IRQ_TYPE_EDGE_FALLING>; - - probe-reset; - - gpio-controller; - interrupt-controller; - }; - }; - - i2c@7 { - #address-cells = <1>; - #size-cells = <0>; - reg = <7>; - }; - }; -}; - -&sdcc1 { - pinctrl-0 = <&sdc_cd_pins>; - pinctrl-names = "default"; - disable-wp; - cd-gpios = <&msmgpio 42 GPIO_ACTIVE_LOW>; /* Active low CD */ -}; |