diff options
Diffstat (limited to 'dts/src/arm/ste-hrefv60plus.dtsi')
-rw-r--r-- | dts/src/arm/ste-hrefv60plus.dtsi | 377 |
1 files changed, 0 insertions, 377 deletions
diff --git a/dts/src/arm/ste-hrefv60plus.dtsi b/dts/src/arm/ste-hrefv60plus.dtsi deleted file mode 100644 index 8f504edefd..0000000000 --- a/dts/src/arm/ste-hrefv60plus.dtsi +++ /dev/null @@ -1,377 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -/* - * Copyright 2012 ST-Ericsson AB - */ - -#include "ste-href-ab8500.dtsi" -#include "ste-href.dtsi" - -/ { - model = "ST-Ericsson HREF (v60+) platform with Device Tree"; - compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500"; - - thermal-zones { - chassis-thermal { - /* Poll every 20 seconds */ - polling-delay = <20000>; - /* Poll every 2nd second when cooling */ - polling-delay-passive = <2000>; - - thermal-sensors = <&therm1>, <&therm2>; - - /* Tripping points made from rough guess about operating conditions */ - trips { - chassis_alert: chassis-alert { - /* At 50 degrees take down the CPU frequency */ - temperature = <50000>; - hysteresis = <3000>; - type = "active"; - }; - chassis_crit: chassis-crit { - /* Just shut down at 70 degrees */ - temperature = <70000>; - hysteresis = <2000>; - type = "critical"; - }; - }; - - /* Push down the operating frequency of the SoC when it gets hot */ - cooling-maps { - map0 { - trip = <&chassis_alert>; - cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; - contribution = <100>; - }; - }; - }; - }; - - /* - * Thermistors on the board, formally to monitor battery temperatures - * but what they measure is the board temperature. - */ - therm1: thermistor@0 { - compatible = "murata,ncp18wb473"; - io-channels = <&gpadc 0x06>; /* AUX1 */ - pullup-uv = <1800000>; - pullup-ohm = <220000>; - pulldown-ohm = <0>; - #thermal-sensor-cells = <0>; - }; - - therm2: thermistor@1 { - compatible = "murata,ncp18wb473"; - io-channels = <&gpadc 0x07>; /* AUX2 */ - pullup-uv = <1800000>; - pullup-ohm = <220000>; - pulldown-ohm = <0>; - #thermal-sensor-cells = <0>; - }; - - soc { - /* Name the GPIO muxed rails on the HREF boards */ - gpio@8012e000 { - /* GPIOs 0 - 31 */ - gpio-line-names = - /* GPIO0,1 used for UART0 BT RX/TX */ - "", "", - "UART_WAKE", - "BT_WAKE", - "", - "SDMMC_1V8_3V_SEL", - "FLASH_LED_SYNC (FLASH_CTRL_0)", - "XENON_READY (FLASH_CTRL_1)", - "", "", "", "", "", "", "", "", - "", "", "", "", - "", - "FLASH_LED_EN (FLASH_CTRL_3)", - "", "", - "", "", "", "", "", - /* Used by UART2 (console) */ - "", "", - "MAGNETOMETER_INT"; - }; - - gpio@8012e080 { - /* GPIOs 32 - 63 */ - gpio-line-names = - "MAGNETOMETER_DRDY", - "", "", "", "", "", "", "", - "", "", "", "", "", "", "", "", - "", "", "", "", "", "", "", "", - "", "", "", "", "", "", "", ""; - }; - - gpio@8000e000 { - /* GPIOs 64 - 95 */ - gpio-line-names = "XENON_EN2 (FLASH_CTRL_4)", - "DISP1_RST", - "DISP2_RST", - "TOUCH_INT2", - "LCD_VSI0_A", - "LCD_VSI1_A", - /* GPIO 70-77 used for ETM */ - "", "", "", "", "", "", "", "", - /* GPIO 78-81 used for YCBCR */ - "", "", "", "", - "ACCELEROMETER_INT1_RDY", - "ACCELEROMETER_INT2", - "TOUCH_INT", - "WLAN_ENA", - "", "", "", "", "", - "FORCE_SENSING_INT", - "FORCE_SENSING_RESET", - "", "", - "SDMMC_CD"; - }; - - gpio@8000e080 { - /* GPIOs 96 - 127 */ - gpio-line-names = "", - "FORCE_SENSING_WU", - "", "", "", "", "", "", - "", "", "", "", "", "", "", "", - "", "", "", "", "", "", "", "", - "", "", "", "", "", "", "", ""; - }; - - gpio@8000e100 { - /* GPIOs 128 - 159 */ - gpio-line-names = "", "", "", "", "", "", "", "", - "", "", "", - "DIPRO_INT", /* GPIO139 */ - "XSHUTDOWN_SECONDARY_SENSOR", - "XSHUTDOWN_PRIMARY_SENSOR", - "NFC_RST (NFC_CTRL_", - "TOUCH_RST", - "NFC_IRQ (NFC_CTRL_1)", - "HAL_SW", - "TOUCH_RST2", - "", "", - "VAUDIO_HF_EN", /* GPIO149 */ - "", "", "", "", "", "", "", "", "", ""; - }; - - gpio@8000e180 { - /* GPIOs 160 - 191 */ - gpio-line-names = "", "", "", "", "", "", "", "", - "", - "SDMMC_EN", - "XENON_CHARGE (FLASH_CONTROL_5)", - "GBF_ENA_RESET", - "", "", "", "", - "", "", "", "", "", "", "", "", - "", "", "", "", "", "", "", ""; - }; - - gpio@8011e000 { - /* GPIOs 192 - 223 */ - gpio-line-names = "HDTV_INTN", - "", "", "", - "HDTV_RSTN", - "", "", "", - "", /* GPIO200 */ - "", "", "", "", "", "", "", - /* GPIO208-216 used for WGBF_MC1 */ - "", "", "", "", "", "", "", "", "", - "SW_FRONT_PROXIMITY", /* GPIO217 */ - "KPD_CTRL_INT", /* Keypad controller */ - "", "", "", "", ""; - }; - - gpio@8011e080 { - /* GPIOs 224 - 255 */ - gpio-line-names = "", "", - "HSIT_ACWAKE0", - "", "", "", "", "", - "", "", "", "", "", "", "", "", - "", "", "", "", "", "", "", "", - "", "", "", "", "", "", "", ""; - }; - - // External Micro SD slot - mmc@80126000 { - cd-gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>; // 95 - }; - - pinctrl { - /* - * Set this up using hogs, as time goes by and as seems fit, these - * can be moved over to being controlled by respective device. - */ - pinctrl-names = "default"; - pinctrl-0 = <&ipgpio_hrefv60_mode>, - <&etm_hrefv60_mode>, - <&nahj_hrefv60_mode>, - <&nfc_hrefv60_mode>, - <&force_hrefv60_mode>, - <&dipro_hrefv60_mode>, - <&vaudio_hf_hrefv60_mode>, - <&gbf_hrefv60_mode>, - <&hdtv_hrefv60_mode>, - <&gpios_hrefv60_mode>; - - sdi0 { - sdi0_default_mode: sdi0_default { - /* SD card detect GPIO pin, extend default state */ - default_hrefv60_cfg1 { - pins = "GPIO95_E8"; - ste,config = <&gpio_in_pu>; - }; - }; - }; - ipgpio { - /* - * XENON Flashgun on image processor GPIO (controlled from image - * processor firmware), mux in these image processor GPIO lines 0 - * (XENON_FLASH_ID), 1 (XENON_READY) and there is an assistant - * LED on IP GPIO 4 (XENON_EN2) on altfunction C, that need bias - * from GPIO21 so pull up 0, 1 and drive 4 and GPIO21 low as output. - */ - ipgpio_hrefv60_mode: ipgpio_hrefv60 { - hrefv60_mux { - function = "ipgpio"; - groups = "ipgpio0_c_1", "ipgpio1_c_1", "ipgpio4_c_1"; - }; - hrefv60_cfg1 { - pins = "GPIO6_AF6", "GPIO7_AG5"; - ste,config = <&in_pu>; - }; - hrefv60_cfg2 { - pins = "GPIO21_AB3"; - ste,config = <&gpio_out_lo>; - }; - hrefv60_cfg3 { - pins = "GPIO64_F3"; - ste,config = <&out_lo>; - }; - }; - }; - etm { - /* - * Drive D19-D23 for the ETM PTM trace interface low, - * (presumably pins are unconnected therefore grounded here, - * the "other alt C1" setting enables these pins) - */ - etm_hrefv60_mode: etm_hrefv60 { - hrefv60_cfg1 { - pins = - "GPIO70_G5", - "GPIO71_G4", - "GPIO72_H4", - "GPIO73_H3", - "GPIO74_J3"; - ste,config = <&gpio_out_lo>; - }; - }; - }; - nahj { - nahj_hrefv60_mode: nahj_hrefv60 { - /* NAHJ CTRL on GPIO76 to low, CTRL_INV on GPIO216 to high */ - hrefv60_cfg1 { - pins = "GPIO76_J2"; - ste,config = <&gpio_out_lo>; - }; - hrefv60_cfg2 { - pins = "GPIO216_AG12"; - ste,config = <&gpio_out_hi>; - }; - }; - }; - nfc { - nfc_hrefv60_mode: nfc_hrefv60 { - /* NFC ENA and RESET to low, pulldown IRQ line */ - hrefv60_cfg1 { - pins = - "GPIO77_H1", /* NFC_ENA */ - "GPIO142_C11"; /* NFC_RESET */ - ste,config = <&gpio_out_lo>; - }; - hrefv60_cfg2 { - pins = "GPIO144_B13"; /* NFC_IRQ */ - ste,config = <&gpio_in_pd>; - }; - }; - }; - force { - force_hrefv60_mode: force_hrefv60 { - hrefv60_cfg1 { - pins = "GPIO91_B6"; /* FORCE_SENSING_INT */ - ste,config = <&gpio_in_pu>; - }; - hrefv60_cfg2 { - pins = - "GPIO92_D6", /* FORCE_SENSING_RST */ - "GPIO97_D9"; /* FORCE_SENSING_WU */ - ste,config = <&gpio_out_lo>; - }; - }; - }; - dipro { - dipro_hrefv60_mode: dipro_hrefv60 { - hrefv60_cfg1 { - pins = "GPIO139_C9"; /* DIPRO_INT */ - ste,config = <&gpio_in_pu>; - }; - }; - }; - vaudio_hf { - vaudio_hf_hrefv60_mode: vaudio_hf_hrefv60 { - /* Audio Amplifier HF enable GPIO */ - hrefv60_cfg1 { - pins = "GPIO149_B14"; /* VAUDIO_HF_EN, enable MAX8968 */ - ste,config = <&gpio_out_hi>; - }; - }; - }; - gbf { - gbf_hrefv60_mode: gbf_hrefv60 { - /* - * GBF (GPS, Bluetooth, FM-radio) interface, - * pull low to reset state - */ - hrefv60_cfg1 { - pins = "GPIO171_D23"; /* GBF_ENA_RESET */ - ste,config = <&gpio_out_lo>; - }; - }; - }; - hdtv { - hdtv_hrefv60_mode: hdtv_hrefv60 { - /* MSP : HDTV INTERFACE GPIO line */ - hrefv60_cfg1 { - pins = "GPIO192_AJ27"; - ste,config = <&gpio_in_pd>; - }; - }; - }; - mcde { - lcd_hrefv60_mode: lcd_hrefv60 { - /* - * Display Interface 1 uses GPIO 65 for RST (reset). - * Display Interface 2 uses GPIO 66 for RST (reset). - * Drive DISP1 reset high (not reset), driver DISP2 reset low (reset) - */ - hrefv60_cfg1 { - pins ="GPIO65_F1"; - ste,config = <&gpio_out_hi>; - }; - hrefv60_cfg2 { - pins ="GPIO66_G3"; - ste,config = <&gpio_out_lo>; - }; - }; - }; - gpios { - /* Dangling GPIO pins */ - gpios_hrefv60_mode: gpios_hrefv60 { - default_cfg1 { - /* Normally UART1 RXD, now dangling */ - pins = "GPIO4_AH6"; - ste,config = <&in_pu>; - }; - }; - }; - }; - }; -}; |