summaryrefslogtreecommitdiffstats
path: root/dts/src/arm/ste-ux500-samsung-janice.dts
diff options
context:
space:
mode:
Diffstat (limited to 'dts/src/arm/ste-ux500-samsung-janice.dts')
-rw-r--r--dts/src/arm/ste-ux500-samsung-janice.dts986
1 files changed, 0 insertions, 986 deletions
diff --git a/dts/src/arm/ste-ux500-samsung-janice.dts b/dts/src/arm/ste-ux500-samsung-janice.dts
deleted file mode 100644
index ed5c79c3d0..0000000000
--- a/dts/src/arm/ste-ux500-samsung-janice.dts
+++ /dev/null
@@ -1,986 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Devicetree for the Samsung Galaxy S Advance GT-I9070 also known as Janice.
- */
-
-/dts-v1/;
-#include "ste-db8500.dtsi"
-#include "ste-ab8500.dtsi"
-#include "ste-dbx5x0-pinctrl.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-
-/ {
- model = "Samsung Galaxy S Advance (GT-I9070)";
- compatible = "samsung,janice", "st-ericsson,u8500";
-
- chosen {
- stdout-path = &serial2;
- };
-
- battery: battery {
- compatible = "samsung,eb535151vu";
- };
-
- thermal-zones {
- battery-thermal {
- /* This zone will be polled by the battery temperature code */
- polling-delay = <0>;
- polling-delay-passive = <0>;
- thermal-sensors = <&bat_therm>;
- };
- };
-
- bat_therm: thermistor {
- compatible = "samsung,1404-001221";
- io-channels = <&gpadc 0x02>; /* BatTemp */
- pullup-uv = <1800000>;
- pullup-ohm = <230000>;
- pulldown-ohm = <0>;
- #thermal-sensor-cells = <0>;
- };
-
- /* External LDO for eMMC LDO VMEM_3V3 controlled by GPIO6 */
- ldo_3v3_reg: regulator-gpio-ldo-3v3 {
- compatible = "regulator-fixed";
- /* Supplied in turn by VBAT */
- regulator-name = "VMEM_3V3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- gpio = <&gpio0 6 GPIO_ACTIVE_HIGH>;
- startup-delay-us = <5000>; // FIXME
- enable-active-high;
- pinctrl-names = "default";
- pinctrl-0 = <&emmc_ldo_en_default_mode>;
- };
-
- /*
- * External Ricoh "TSP" regulator for the touchscreen.
- * One GPIO line controls two voltages of 3.3V and 1.8V
- * this line is known as "TSP_LDO_ON1" in the schematics.
- */
- ldo_tsp_3v3_reg: regulator-gpio-tsp-ldo-3v3 {
- compatible = "regulator-fixed";
- /* Supplied in turn by VBAT */
- regulator-name = "LDO_TSP_A3V3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- /* GPIO94 controls this regulator */
- gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>;
- /* 70 ms power-on delay */
- startup-delay-us = <70000>;
- enable-active-high;
- pinctrl-names = "default";
- pinctrl-0 = <&tsp_ldo_en_default_mode>;
- };
- ldo_tsp_1v8_reg: regulator-gpio-tsp-ldo-1v8 {
- compatible = "regulator-fixed";
- /* Supplied in turn by VBAT */
- regulator-name = "VREG_TSP_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- /* GPIO94 controls this regulator */
- gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>;
- /* 70 ms power-on delay */
- startup-delay-us = <70000>;
- enable-active-high;
- pinctrl-names = "default";
- pinctrl-0 = <&tsp_ldo_en_default_mode>;
- };
-
- /*
- * External Ricoh "TSP" regulator for the touchkeys.
- * Two GPIO lines controls two voltages of 3.3V and 1.8V
- * TSP_LDO_ON2 controls VREG_TOUCHKEY_1V8
- * EN_LED_LDO controls VREG_KLED_3V3 (key LED)
- */
- ldo_kled_3v3_reg: regulator-gpio-vreg-kled-3v3 {
- compatible = "regulator-fixed";
- /* Supplied in turn by VBAT */
- regulator-name = "VREG_KLED_3V3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- /* GPIO68 controls this regulator */
- gpio = <&gpio2 4 GPIO_ACTIVE_HIGH>;
- /* 70 ms power-on delay */
- startup-delay-us = <70000>;
- enable-active-high;
- pinctrl-names = "default";
- pinctrl-0 = <&en_led_ldo_default_mode>;
- };
- ldo_touchkey_1v8_reg: regulator-gpio-vreg-touchkey-1v8 {
- compatible = "regulator-fixed";
- /* Supplied in turn by VBAT */
- regulator-name = "VREG_TOUCHKEY_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- /* GPIO89 controls this regulator */
- gpio = <&gpio2 25 GPIO_ACTIVE_HIGH>;
- /* 70 ms power-on delay */
- startup-delay-us = <70000>;
- enable-active-high;
- pinctrl-names = "default";
- pinctrl-0 = <&tsp_ldo_on2_default_mode>;
- };
-
-
- /*
- * External Ricoh RP152L010B-TR LCD LDO regulator for the display.
- * LCD_PWR_EN controls a 3.0V and 1.8V output.
- */
- lcd_3v0_reg: regulator-gpio-lcd-3v0 {
- compatible = "regulator-fixed";
- /* Supplied in turn by VBAT */
- regulator-name = "VREG_LCD_3V0";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- /* GPIO219 controls this regulator */
- gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- pinctrl-names = "default";
- pinctrl-0 = <&lcd_pwr_en_default_mode>;
- };
- lcd_1v8_reg: regulator-gpio-lcd-1v8 {
- compatible = "regulator-fixed";
- /* Supplied in turn by VBAT */
- regulator-name = "VREG_LCD_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- /* GPIO219 controls this regulator */
- gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- pinctrl-names = "default";
- pinctrl-0 = <&lcd_pwr_en_default_mode>;
- };
-
- /*
- * This regulator is a GPIO line that drives the Broadcom WLAN
- * line WL_REG_ON high and enables the internal regulators
- * inside the chip. Unfortunatley it is erroneously named
- * WLAN_RST_N on the schematic but it is not a reset line.
- *
- * The voltage specified here is only used to determine the OCR mask,
- * the for the SDIO connector, the chip is actually connected
- * directly to VBAT.
- */
- wl_reg: regulator-gpio-wlan {
- compatible = "regulator-fixed";
- regulator-name = "WL_REG_ON";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- startup-delay-us = <100000>;
- /* GPIO215 (WLAN_RST_N to WL_REG_ON) */
- gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- pinctrl-names = "default";
- pinctrl-0 = <&wlan_ldo_en_default>;
- };
-
-
- gpio-keys {
- compatible = "gpio-keys";
- pinctrl-names = "default";
- pinctrl-0 = <&gpio_keys_default_mode>;
-
- button-home {
- linux,code = <KEY_HOME>;
- label = "HOME";
- /* GPIO91 */
- gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
- };
- button-volup {
- linux,code = <KEY_VOLUMEUP>;
- label = "VOL+";
- /* GPIO67 */
- gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
- };
- button-voldown {
- linux,code = <KEY_VOLUMEDOWN>;
- label = "VOL-";
- /* GPIO92 */
- gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
- };
- };
-
- /* Richtek RT8515GQW Flash LED Driver IC */
- flash {
- compatible = "richtek,rt8515";
- /* GPIO 140 */
- enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
- /* GPIO 141 */
- ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
- /*
- * RFS is 16 kOhm and RTS is 100 kOhm giving
- * the flash max current 343mA and torch max
- * current 55 mA.
- */
- richtek,rfs-ohms = <16000>;
- richtek,rts-ohms = <100000>;
- pinctrl-names = "default";
- pinctrl-0 = <&gpio_flash_default_mode>;
-
- led {
- function = LED_FUNCTION_FLASH;
- color = <LED_COLOR_ID_WHITE>;
- flash-max-timeout-us = <250000>;
- flash-max-microamp = <343750>;
- led-max-microamp = <55000>;
- };
- };
-
- /* Bit-banged I2C on GPIO143 and GPIO144 also called "SUBPMU I2C" */
- i2c-gpio-0 {
- compatible = "i2c-gpio";
- sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
- scl-gpios = <&gpio4 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c_gpio_0_default>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- /* Yamaha YAS530 magnetometer */
- magnetometer@2e {
- compatible = "yamaha,yas530";
- reg = <0x2e>;
- /* VDD 3V */
- vdd-supply = <&ab8500_ldo_aux1_reg>;
- /* IOVDD 1.8V */
- iovdd-supply = <&ab8500_ldo_aux2_reg>;
- /* GPIO204 COMPASS_RST_N */
- reset-gpios = <&gpio6 12 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&yas529_default>;
- };
- /* TODO: this should also be used by the NCP6914 Camera power management unit */
- };
-
- /*
- * These pins do have an spi controller, however the controller on
- * these pins is not the fully featured PL022 SSP/SPI block but the
- * ST Micro diet "PL023" version. One of the lacking features in
- * this derivative is 3wire support, so it cannot be used to drive
- * this panel interface. We have to use GPIO bit-banging instead.
- */
- spi-gpio-0 {
- compatible = "spi-gpio";
- /* Clock on GPIO220 */
- sck-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>;
- /* MISO/MOSI on GPIO224 (no separate MISO pin) */
- mosi-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
- /* Chip select on GPIO223 */
- cs-gpios = <&gpio6 31 GPIO_ACTIVE_LOW>;
- num-chipselects = <1>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&spi_gpio_0_default>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- panel@0 {
- compatible = "samsung,s6e63m0";
- reg = <0>;
- vdd3-supply = <&lcd_3v0_reg>;
- vci-supply = <&lcd_1v8_reg>;
- /* Reset on GPIO139 */
- reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&panel_default_mode>;
- spi-3wire;
- /* TYPE 3: inverse clock polarity and phase */
- spi-cpha;
- spi-cpol;
-
- port {
- panel_in: endpoint {
- remote-endpoint = <&display_out>;
- };
- };
- };
- };
-
- /*
- * Current sense amplifier on the light sensor to convert current to
- * voltage. We do not know if this is the actual configuration. The
- * sense resistor value was found by calibrating in a room ambient
- * light with a second mobile phone light sensor as reference. If you
- * pry a Janice phone apart and inspect it you may figure this out.
- */
- gp2a_shunt: current-sense-shunt {
- compatible = "current-sense-shunt";
- io-channels = <&gpadc 0x07>;
- shunt-resistor-micro-ohms = <15000000>; /* 15 ohms c:a */
- #io-channel-cells = <0>;
- io-channel-ranges;
- };
-
- /* Bit-banged I2C on GPIO196 and GPIO197 also called "TOUCHKEY_I2C" */
- i2c-gpio-1 {
- compatible = "i2c-gpio";
- sda-gpios = <&gpio6 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
- scl-gpios = <&gpio6 4 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
- clock-frequency = <400000>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c_gpio_1_default>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- touchkey@20 {
- compatible = "coreriver,tc360-touchkey";
- reg = <0x20>;
- vdd-supply = <&ldo_kled_3v3_reg>;
- vcc-supply = <&ldo_touchkey_1v8_reg>;
- vddio-supply = <&ldo_touchkey_1v8_reg>;
-
- /* Interrupt on GPIO 198 */
- interrupt-parent = <&gpio6>;
- interrupts = <6 IRQ_TYPE_EDGE_RISING>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&touchkey_default_mode>;
- linux,keycodes = <KEY_MENU KEY_BACK>;
- };
- };
-
- /* Bit-banged I2C on GPIO201 and GPIO202 also called "MOT_I2C" */
- i2c-gpio-2 {
- compatible = "i2c-gpio";
- sda-gpios = <&gpio6 10 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
- scl-gpios = <&gpio6 9 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c_gpio_2_default>;
- #address-cells = <1>;
- #size-cells = <0>;
- /* TODO: add the Immersion ISA1200 I2C device here */
- };
-
- /* Bit-banged I2C on GPIO151 and GPIO152 also called "NFC_I2C" */
- i2c-gpio-3 {
- compatible = "i2c-gpio";
- sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
- scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c_gpio_3_default>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- nfc@30 {
- compatible = "nxp,pn547", "nxp,nxp-nci-i2c";
- reg = <0x30>;
- /* NFC IRQ on GPIO32 */
- interrupt-parent = <&gpio1>;
- interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
- /* GPIO 31 */
- firmware-gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>;
- /* GPIO88 */
- enable-gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
- pinctrl-names = "default";
- pinctrl-0 = <&pn547_janice_default>;
- };
- };
-
- soc {
- /* External Micro SD slot */
- mmc@80126000 {
- arm,primecell-periphid = <0x10480180>;
- max-frequency = <50000000>;
- bus-width = <4>;
- cap-sd-highspeed;
- cap-mmc-highspeed;
- st,sig-dir-cmd;
- st,sig-dir-dat0;
- st,sig-dir-dat2;
- st,sig-pin-fbclk;
- full-pwr-cycle;
- /* MMC is powered by AUX3 1.2V .. 2.91V */
- vmmc-supply = <&ab8500_ldo_aux3_reg>;
- /* 2.9 V level translator is using AUX3 at 2.9 V as well */
- vqmmc-supply = <&ab8500_ldo_aux3_reg>;
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&mc0_a_2_default>;
- pinctrl-1 = <&mc0_a_2_sleep>;
- cd-gpios = <&gpio6 25 GPIO_ACTIVE_LOW>; // GPIO217
- status = "okay";
- };
-
- /* WLAN SDIO channel */
- mmc@80118000 {
- arm,primecell-periphid = <0x10480180>;
- max-frequency = <50000000>;
- bus-width = <4>;
- non-removable;
- cap-sd-highspeed;
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&mc1_a_2_default>;
- pinctrl-1 = <&mc1_a_2_sleep>;
- /*
- * GPIO-controlled voltage enablement: this drives
- * the WL_REG_ON line high when we use this device.
- * Represented as regulator to fill OCR mask.
- */
- vmmc-supply = <&wl_reg>;
-
- #address-cells = <1>;
- #size-cells = <0>;
- status = "okay";
-
- wifi@1 {
- compatible = "brcm,bcm4330-fmac", "brcm,bcm4329-fmac";
- reg = <1>;
- /* GPIO216 WL_HOST_WAKE */
- interrupt-parent = <&gpio6>;
- interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
- interrupt-names = "host-wake";
- pinctrl-names = "default";
- pinctrl-0 = <&wlan_default_mode>;
- };
- };
-
- /* eMMC */
- mmc@80005000 {
- arm,primecell-periphid = <0x10480180>;
- max-frequency = <50000000>;
- bus-width = <8>;
- non-removable;
- cap-mmc-highspeed;
- mmc-ddr-1_8v;
- no-sdio;
- no-sd;
- vmmc-supply = <&ldo_3v3_reg>;
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&mc2_a_1_default>;
- pinctrl-1 = <&mc2_a_1_sleep>;
- status = "okay";
- };
-
- /* GBF (Bluetooth) UART */
- uart@80120000 {
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&u0_a_1_default>;
- pinctrl-1 = <&u0_a_1_sleep>;
- status = "okay";
-
- bluetooth {
- /* BCM4330B1 actually */
- compatible = "brcm,bcm4330-bt";
- /* GPIO222 rail BT_VREG_EN to BT_REG_ON */
- shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
- /* BT_WAKE on GPIO199 */
- device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
- /* BT_HOST_WAKE on GPIO97 */
- /* FIXME: convert to interrupt */
- host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>;
- /* BT_RST_N on GPIO209 */
- reset-gpios = <&gpio6 17 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&bluetooth_default_mode>;
- };
- };
-
- /* GPS UART */
- uart@80121000 {
- status = "okay";
- pinctrl-names = "default", "sleep";
- /* CTS/RTS is not used, CTS is repurposed as GPIO */
- pinctrl-0 = <&u1rxtx_a_1_default>;
- pinctrl-1 = <&u1rxtx_a_1_sleep>;
-
- gnss {
- /*
- * The Low Noise Amplifier (LNA) power and enablement is controlled
- * autonomously by the GSD4t.
- * Janice has a SiRFstarIV-based GSD4t
- * Golden has a SiRFstarV 5t-based CSRG05TA03-ICJE-R.
- */
- compatible = "csr,gsd4t";
- /* GPS_RSTN on GPIO21 */
- reset-gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
- /* GPS_ON_OFF on GPIO96 */
- sirf,onoff-gpios = <&gpio3 0 GPIO_ACTIVE_HIGH>;
- /* GPS_1V8 (VSMPS2) */
- vcc-supply = <&db8500_vsmps2_reg>;
- pinctrl-names = "default";
- pinctrl-0 = <&gsd4t_janice_default>;
- /* According to /etc/sirfgps.conf */
- current-speed = <460800>;
- };
- };
-
- /* Debugging console UART connected to TSU6111RSVR (FSA880) */
- uart@80007000 {
- status = "okay";
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&u2rxtx_c_1_default>;
- pinctrl-1 = <&u2rxtx_c_1_sleep>;
- };
-
- prcmu@80157000 {
- ab8500 {
- phy {
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&usb_a_1_default>;
- pinctrl-1 = <&usb_a_1_sleep>;
- };
-
- ab8500_fg {
- line-impedance-micro-ohms = <15000>;
- };
-
- regulator {
- ab8500_ldo_aux1 {
- /* Used for VDD for sensors */
- regulator-name = "V-SENSORS-VDD";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- ab8500_ldo_aux2 {
- /* Used for VIO for sensors */
- regulator-name = "V-SENSORS-VIO";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ab8500_ldo_aux3 {
- /* Used for voltage for external MMC/SD card */
- regulator-name = "V-MMC-SD";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <2910000>;
- };
- };
- };
- };
-
- /* I2C0 */
- i2c@80004000 {
- status = "okay";
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&i2c0_a_1_default>;
- pinctrl-1 = <&i2c0_a_1_sleep>;
-
- proximity@44 {
- /* Janice has the GP2AP002A00F with light sensor */
- compatible = "sharp,gp2ap002a00f";
- clock-frequency = <400000>;
- reg = <0x44>;
-
- interrupt-parent = <&gpio4>;
- interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
- vdd-supply = <&ab8500_ldo_aux1_reg>;
- vio-supply = <&ab8500_ldo_aux2_reg>;
- /* ADC channel AUX2 to read ALSOUT ambient light sensor out */
- io-channels = <&gp2a_shunt>;
- io-channel-names = "alsout";
- pinctrl-names = "default";
- pinctrl-0 = <&gp2ap002_janice_default>;
- /* B1 mode (arch/arm/mach-ux500/include/mach/gp2a.h) */
- sharp,proximity-far-hysteresis = /bits/ 8 <0x40>;
- sharp,proximity-close-hysteresis = /bits/ 8 <0x0f>;
- };
- };
-
- /* I2C1 on GPIO16 and GPIO17 also called "MUS I2C" */
- i2c@80122000 {
- status = "okay";
- pinctrl-names = "default","sleep";
- pinctrl-0 = <&i2c1_b_2_default>;
- pinctrl-1 = <&i2c1_b_2_sleep>;
-
- /* Texas Instruments TSU6111 micro USB switch */
- usb-switch@25 {
- compatible = "ti,tsu6111";
- reg = <0x25>;
- /* Interrupt JACK_INT_N on GPIO95 */
- interrupt-parent = <&gpio2>;
- interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
- pinctrl-names = "default";
- pinctrl-0 = <&tsu6111_janice_default>;
- };
- };
-
- /* I2C2 on GPIO10 and GPIO11 also called "SENSORS I2C" */
- i2c@80128000 {
- status = "okay";
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&i2c2_b_2_default>;
- pinctrl-1 = <&i2c2_b_2_sleep>;
-
- gyroscope@68 {
- compatible = "invensense,mpu3050";
- reg = <0x68>;
- /* GPIO226 interrupt */
- interrupt-parent = <&gpio7>;
- interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
- /* FIXME: no idea about this */
- mount-matrix = "1", "0", "0",
- "0", "1", "0",
- "0", "0", "1";
- vlogic-supply = <&ab8500_ldo_aux2_reg>; // 1.8V
- vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
- pinctrl-names = "default";
- pinctrl-0 = <&mpu3050_janice_default>;
-
- /*
- * The MPU-3050 acts as a hub for the
- * accelerometer.
- */
- i2c-gate {
- #address-cells = <1>;
- #size-cells = <0>;
-
- /* Bosch BMA222 accelerometer */
- accelerometer@8 {
- compatible = "bosch,bma222";
- reg = <0x08>;
- mount-matrix = "0", "-1", "0",
- "1", "0", "0",
- "0", "0", "1";
- vddio-supply = <&ab8500_ldo_aux2_reg>; // 1.8V
- vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
- };
- };
- };
- };
-
- /* I2C3 */
- i2c@80110000 {
- status = "okay";
-
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&i2c3_c_2_default>;
- pinctrl-1 = <&i2c3_c_2_sleep>;
-
- /* Atmel mXT224E touchscreen */
- touchscreen@4a {
- compatible = "atmel,maxtouch";
- reg = <0x4a>;
- /* GPIO218 (TSP_INT_1V8) */
- interrupt-parent = <&gpio6>;
- interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
- /* VDDA is "analog supply", 2.57-3.47 V */
- vdda-supply = <&ldo_tsp_3v3_reg>;
- /* VDD is "digital supply" 1.71-3.47V */
- vdd-supply = <&ldo_tsp_1v8_reg>;
- pinctrl-names = "default";
- pinctrl-0 = <&tsp_default>;
- };
- };
-
- mcde@a0350000 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&dpi_default_mode>;
-
- port {
- display_out: endpoint {
- remote-endpoint = <&panel_in>;
- };
- };
- };
- };
-};
-
-&pinctrl {
- /*
- * This extends the MC0_A_2 default config to include
- * the card detect GPIO217 line.
- */
- sdi0 {
- mc0_a_2_default {
- default_cfg4 {
- pins = "GPIO217_AH12"; /* card detect */
- ste,config = <&gpio_in_pd>;
- };
- };
- };
- mcde {
- dpi_default_mode: dpi_default {
- default_mux1 {
- /* Mux in all the data lines */
- function = "lcd";
- groups =
- /* Data lines D0-D7 GPIO70..GPIO77 */
- "lcd_d0_d7_a_1",
- /* Data lines D8-D11 GPIO78..GPIO81 */
- "lcd_d8_d11_a_1",
- /* Data lines D12-D15 GPIO82..GPIO85 */
- "lcd_d12_d15_a_1",
- /* Data lines D16-D23 GPIO161..GPIO168 */
- "lcd_d16_d23_b_1";
- };
- default_mux2 {
- function = "lcda";
- /* Clock line on GPIO150, DE, VSO, HSO on GPIO169..GPIO171 */
- groups = "lcdaclk_b_1", "lcda_b_1";
- };
- /* Input, no pull-up is the default state for pins used for an alt function */
- default_cfg1 {
- pins = "GPIO150_C14", "GPIO169_D22", "GPIO170_C23", "GPIO171_D23";
- ste,config = <&in_nopull>;
- };
- };
- };
- /* GPIO for panel reset control */
- panel {
- panel_default_mode: panel_default {
- janice_cfg1 {
- /* Reset line */
- pins = "GPIO139_C9";
- ste,config = <&gpio_out_lo>;
- };
- };
- };
- /* GPIO that enables the LDO regulator for the eMMC */
- emmc-ldo {
- emmc_ldo_en_default_mode: emmc_ldo_default {
- /* LDO enable on GPIO6 */
- janice_cfg1 {
- pins = "GPIO6_AF6";
- ste,config = <&gpio_out_hi>;
- };
- };
- };
- /* GPIO that enables the LDO regulator for the touchscreen */
- tsp-ldo {
- tsp_ldo_en_default_mode: tsp_ldo_default {
- /* LDO enable on GPIO94 */
- janice_cfg1 {
- pins = "GPIO94_D7";
- ste,config = <&gpio_out_hi>;
- };
- };
- };
- /* GPIO that enables the LDO regulator for the key LED */
- key-led {
- en_led_ldo_default_mode: en_led_ldo_default {
- /* EN_LED_LDO on GPIO68 */
- janice_cfg1 {
- pins = "GPIO68_E1";
- ste,config = <&gpio_out_hi>;
- };
- };
- };
- /* GPIO that enables the LDO regulator for the touchkeys */
- touchkey-ldo {
- tsp_ldo_on2_default_mode: tsp_ldo_on2_default {
- /* TSP_LDO_ON2 on GPIO89 */
- janice_cfg1 {
- pins = "GPIO89_E6";
- ste,config = <&gpio_out_lo>;
- };
- };
- };
- touchkey {
- touchkey_default_mode: touchkey_default {
- janice_cfg1 {
- /* Interrupt */
- pins = "GPIO198_AG25";
- ste,config = <&gpio_in_nopull>;
- };
- janice_cfg2 {
- /* Reset, actually completely unused (not routed) */
- pins = "GPIO205_AG23";
- ste,config = <&gpio_in_pd>;
- };
- };
- };
- /* GPIO that enabled the LDO regulator for the LCD display */
- lcd-ldo {
- lcd_pwr_en_default_mode: lcd_pwr_en_default {
- /* LCD_PWR_EN on GPIO219 */
- janice_cfg1 {
- pins = "GPIO219_AG10";
- ste,config = <&gpio_out_hi>;
- };
- };
- };
- /* GPIO that enables the WLAN internal LDO regulators */
- wlan-ldo {
- wlan_ldo_en_default: wlan_ldo_default {
- /* GPIO215 named WLAN_RST_N */
- janice_cfg1 {
- pins = "GPIO215_AH13";
- ste,config = <&gpio_out_lo>;
- };
- };
- };
- /* Flash and torch */
- flash {
- gpio_flash_default_mode: flash_default {
- janice_cfg1 {
- pins = "GPIO140_B11", "GPIO141_C12";
- ste,config = <&gpio_out_lo>;
- };
- };
- };
- /* GPIO keys */
- gpio-keys {
- gpio_keys_default_mode: gpio_keys_default {
- skomer_cfg1 {
- pins = "GPIO67_G2", /* VOL UP */
- "GPIO91_B6", /* HOME */
- "GPIO92_D6"; /* VOL DOWN */
- ste,config = <&gpio_in_pu>;
- };
- };
- };
- /* Interrupt line for the Atmel MXT228 touchscreen */
- tsp {
- tsp_default: tsp_default {
- janice_cfg1 {
- pins = "GPIO218_AH11"; /* TSP_INT_1V8 */
- ste,config = <&gpio_in_nopull>;
- };
- };
- };
- /* Reset line for the Yamaha YAS529 magnetometer */
- yas529 {
- yas529_default: yas529_janice {
- janice_cfg1 {
- pins = "GPIO204_AF23";
- ste,config = <&gpio_out_hi>;
- };
- };
- };
- /* Interrupt line for light/proximity sensor GP2AP002 */
- gp2ap002 {
- gp2ap002_janice_default: gp2ap002_janice {
- janice_cfg1 {
- pins = "GPIO146_D13";
- ste,config = <&gpio_in_nopull>;
- };
- };
- };
- /* Interrupt line for Invensense MPU3050 gyroscope */
- mpu3050 {
- mpu3050_janice_default: mpu3050_janice {
- janice_cfg1 {
- /* GPIO226 used for IRQ */
- pins = "GPIO226_AF8";
- ste,config = <&gpio_in_nopull>;
- };
- };
- };
- /* GPIO-based I2C bus for magnetometer and NCP6914 */
- i2c-gpio-0 {
- i2c_gpio_0_default: i2c_gpio_0 {
- janice_cfg1 {
- pins = "GPIO143_D12", "GPIO144_B13";
- ste,config = <&gpio_in_nopull>;
- };
- };
- };
- /* GPIO-based I2C bus for the Cypress touchkeys */
- i2c-gpio-1 {
- i2c_gpio_1_default: i2c_gpio_1 {
- janice_cfg1 {
- pins = "GPIO196_AG26", "GPIO197_AH24";
- ste,config = <&gpio_in_nopull>;
- };
- };
- };
- /* GPIO-based I2C bus for the Immersion ISA1200 */
- i2c-gpio-2 {
- i2c_gpio_2_default: i2c_gpio_2 {
- janice_cfg1 {
- pins = "GPIO201_AF24", "GPIO202_AF25";
- ste,config = <&gpio_in_nopull>;
- };
- };
- };
- /* GPIO-based I2C bus for the NFC */
- i2c-gpio-3 {
- i2c_gpio_3_default: i2c_gpio_3 {
- janice_cfg1 {
- pins = "GPIO151_D17", "GPIO152_D16";
- ste,config = <&gpio_in_nopull>;
- };
- };
- };
- /* GPIO-based SPI bus for the display */
- spi-gpio-0 {
- spi_gpio_0_default: spi_gpio_0 {
- janice_cfg1 {
- pins = "GPIO220_AH10", "GPIO223_AH9", "GPIO224_AG9";
- ste,config = <&gpio_out_hi>;
- };
- /* This pin is unused but belongs with this SPI block */
- janice_cfg2 {
- pins = "GPIO225_AG8";
- ste,config = <&in_pd>;
- };
- };
- };
- wlan {
- wlan_default_mode: wlan_default {
- /* GPIO216 for WL_HOST_WAKE */
- janice_cfg2 {
- pins = "GPIO216_AG12";
- ste,config = <&gpio_in_pd>;
- };
- };
- };
- bluetooth {
- bluetooth_default_mode: bluetooth_default {
- /* GPIO199 BT_WAKE and GPIO222 BT_VREG_ON */
- janice_cfg1 {
- pins = "GPIO199_AH23", "GPIO222_AJ9";
- ste,config = <&gpio_out_lo>;
- };
- /* GPIO97 BT_HOST_WAKE */
- janice_cfg2 {
- pins = "GPIO97_D9";
- ste,config = <&gpio_in_nopull>;
- };
- /* GPIO209 BT_RST_N */
- janice_cfg3 {
- pins = "GPIO209_AG15";
- ste,config = <&gpio_out_hi>;
- };
- };
- };
- /* Interrupt line for TI TSU6111 Micro USB switch */
- tsu6111 {
- tsu6111_janice_default: tsu6111_janice {
- janice_cfg1 {
- /* GPIO95 used for IRQ */
- pins = "GPIO95_E8";
- ste,config = <&gpio_in_nopull>;
- };
- };
- };
- nfc {
- pn547_janice_default: pn547_janice {
- /* Interrupt line */
- janice_cfg1 {
- pins = "GPIO32_V2";
- ste,config = <&gpio_in_nopull>;
- };
- /* Enable and firmware GPIOs */
- janice_cfg2 {
- pins = "GPIO31_V3", "GPIO88_C4";
- ste,config = <&gpio_out_lo>;
- };
- };
- };
- gsd4t {
- gsd4t_janice_default: gsd4t_janice {
- /* Reset line, start out asserted */
- janice_cfg1 {
- pins = "GPIO21_AB3";
- ste,config = <&gpio_out_lo>;
- };
- /* GPS_ON_OFF, start out deasserted (off) */
- janice_cfg2 {
- pins = "GPIO96_D8";
- ste,config = <&gpio_out_lo>;
- };
- /* Unused power enablement line, used in R0.0 and R0.1 boards */
- janice_cfg3 {
- pins = "GPIO86_C6";
- ste,config = <&gpio_in_pd>;
- };
- };
- };
-};