diff options
Diffstat (limited to 'dts/src/arm/stm32mp157c-ev1.dts')
-rw-r--r-- | dts/src/arm/stm32mp157c-ev1.dts | 399 |
1 files changed, 0 insertions, 399 deletions
diff --git a/dts/src/arm/stm32mp157c-ev1.dts b/dts/src/arm/stm32mp157c-ev1.dts deleted file mode 100644 index d142dd30e1..0000000000 --- a/dts/src/arm/stm32mp157c-ev1.dts +++ /dev/null @@ -1,399 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) -/* - * Copyright (C) STMicroelectronics 2017 - All Rights Reserved - * Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics. - */ -/dts-v1/; - -#include "stm32mp157c-ed1.dts" -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/input/input.h> - -/ { - model = "STMicroelectronics STM32MP157C eval daughter on eval mother"; - compatible = "st,stm32mp157c-ev1", "st,stm32mp157c-ed1", "st,stm32mp157"; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - aliases { - serial0 = &uart4; - serial1 = &usart3; - ethernet0 = ðernet0; - }; - - clocks { - clk_ext_camera: clk-ext-camera { - #clock-cells = <0>; - compatible = "fixed-clock"; - clock-frequency = <24000000>; - }; - }; - - joystick { - compatible = "gpio-keys"; - pinctrl-0 = <&joystick_pins>; - pinctrl-names = "default"; - button-0 { - label = "JoySel"; - linux,code = <KEY_ENTER>; - interrupt-parent = <&stmfx_pinctrl>; - interrupts = <0 IRQ_TYPE_EDGE_RISING>; - }; - button-1 { - label = "JoyDown"; - linux,code = <KEY_DOWN>; - interrupt-parent = <&stmfx_pinctrl>; - interrupts = <1 IRQ_TYPE_EDGE_RISING>; - }; - button-2 { - label = "JoyLeft"; - linux,code = <KEY_LEFT>; - interrupt-parent = <&stmfx_pinctrl>; - interrupts = <2 IRQ_TYPE_EDGE_RISING>; - }; - button-3 { - label = "JoyRight"; - linux,code = <KEY_RIGHT>; - interrupt-parent = <&stmfx_pinctrl>; - interrupts = <3 IRQ_TYPE_EDGE_RISING>; - }; - button-4 { - label = "JoyUp"; - linux,code = <KEY_UP>; - interrupt-parent = <&stmfx_pinctrl>; - interrupts = <4 IRQ_TYPE_EDGE_RISING>; - }; - }; - - panel_backlight: panel-backlight { - compatible = "gpio-backlight"; - gpios = <&gpiod 13 GPIO_ACTIVE_LOW>; - default-on; - status = "okay"; - }; -}; - -&cec { - pinctrl-names = "default"; - pinctrl-0 = <&cec_pins_a>; - status = "okay"; -}; - -&dcmi { - status = "okay"; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&dcmi_pins_a>; - pinctrl-1 = <&dcmi_sleep_pins_a>; - - port { - dcmi_0: endpoint { - remote-endpoint = <&ov5640_0>; - bus-type = <5>; - bus-width = <8>; - hsync-active = <0>; - vsync-active = <0>; - pclk-sample = <1>; - }; - }; -}; - -&dsi { - phy-dsi-supply = <®18>; - status = "okay"; - - ports { - port@0 { - reg = <0>; - dsi_in: endpoint { - remote-endpoint = <<dc_ep0_out>; - }; - }; - - port@1 { - reg = <1>; - dsi_out: endpoint { - remote-endpoint = <&dsi_panel_in>; - }; - }; - }; - - panel-dsi@0 { - compatible = "raydium,rm68200"; - reg = <0>; - reset-gpios = <&gpiof 15 GPIO_ACTIVE_LOW>; - backlight = <&panel_backlight>; - power-supply = <&v3v3>; - status = "okay"; - - port { - dsi_panel_in: endpoint { - remote-endpoint = <&dsi_out>; - }; - }; - }; -}; - -ðernet0 { - status = "okay"; - pinctrl-0 = <ðernet0_rgmii_pins_a>; - pinctrl-1 = <ðernet0_rgmii_sleep_pins_a>; - pinctrl-names = "default", "sleep"; - phy-mode = "rgmii-id"; - max-speed = <1000>; - phy-handle = <&phy0>; - - mdio0 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "snps,dwmac-mdio"; - phy0: ethernet-phy@0 { - reg = <0>; - }; - }; -}; - -&fmc { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&fmc_pins_a>; - pinctrl-1 = <&fmc_sleep_pins_a>; - status = "okay"; - - nand-controller@4,0 { - status = "okay"; - - nand@0 { - reg = <0>; - nand-on-flash-bbt; - #address-cells = <1>; - #size-cells = <1>; - }; - }; -}; - -&i2c2 { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&i2c2_pins_a>; - pinctrl-1 = <&i2c2_sleep_pins_a>; - i2c-scl-rising-time-ns = <185>; - i2c-scl-falling-time-ns = <20>; - status = "okay"; - - ov5640: camera@3c { - compatible = "ovti,ov5640"; - reg = <0x3c>; - clocks = <&clk_ext_camera>; - clock-names = "xclk"; - DOVDD-supply = <&v2v8>; - powerdown-gpios = <&stmfx_pinctrl 18 (GPIO_ACTIVE_HIGH | GPIO_PUSH_PULL)>; - reset-gpios = <&stmfx_pinctrl 19 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>; - rotation = <180>; - status = "okay"; - - port { - ov5640_0: endpoint { - remote-endpoint = <&dcmi_0>; - bus-width = <8>; - data-shift = <2>; /* lines 9:2 are used */ - hsync-active = <0>; - vsync-active = <0>; - pclk-sample = <1>; - }; - }; - }; - - stmfx: stmfx@42 { - compatible = "st,stmfx-0300"; - reg = <0x42>; - interrupts = <8 IRQ_TYPE_EDGE_RISING>; - interrupt-parent = <&gpioi>; - vdd-supply = <&v3v3>; - - stmfx_pinctrl: pinctrl { - compatible = "st,stmfx-0300-pinctrl"; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - gpio-ranges = <&stmfx_pinctrl 0 0 24>; - - joystick_pins: joystick-pins { - pins = "gpio0", "gpio1", "gpio2", "gpio3", "gpio4"; - bias-pull-down; - }; - }; - }; -}; - -&i2c5 { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&i2c5_pins_a>; - pinctrl-1 = <&i2c5_sleep_pins_a>; - i2c-scl-rising-time-ns = <185>; - i2c-scl-falling-time-ns = <20>; - status = "okay"; -}; - -<dc { - status = "okay"; - - port { - ltdc_ep0_out: endpoint@0 { - reg = <0>; - remote-endpoint = <&dsi_in>; - }; - }; -}; - -&m_can1 { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&m_can1_pins_a>; - pinctrl-1 = <&m_can1_sleep_pins_a>; - status = "okay"; -}; - -&qspi { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>; - pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a &qspi_bk2_sleep_pins_a>; - reg = <0x58003000 0x1000>, <0x70000000 0x4000000>; - #address-cells = <1>; - #size-cells = <0>; - status = "okay"; - - flash0: flash@0 { - compatible = "jedec,spi-nor"; - reg = <0>; - spi-rx-bus-width = <4>; - spi-max-frequency = <108000000>; - #address-cells = <1>; - #size-cells = <1>; - }; - - flash1: flash@1 { - compatible = "jedec,spi-nor"; - reg = <1>; - spi-rx-bus-width = <4>; - spi-max-frequency = <108000000>; - #address-cells = <1>; - #size-cells = <1>; - }; -}; - -&sdmmc3 { - pinctrl-names = "default", "opendrain", "sleep"; - pinctrl-0 = <&sdmmc3_b4_pins_a>; - pinctrl-1 = <&sdmmc3_b4_od_pins_a>; - pinctrl-2 = <&sdmmc3_b4_sleep_pins_a>; - broken-cd; - st,neg-edge; - bus-width = <4>; - vmmc-supply = <&v3v3>; - status = "disabled"; -}; - -&spi1 { - pinctrl-names = "default"; - pinctrl-0 = <&spi1_pins_a>; - status = "disabled"; -}; - -&timers2 { - /* spare dmas for other usage (un-delete to enable pwm capture) */ - /delete-property/dmas; - /delete-property/dma-names; - status = "disabled"; - pwm { - pinctrl-0 = <&pwm2_pins_a>; - pinctrl-1 = <&pwm2_sleep_pins_a>; - pinctrl-names = "default", "sleep"; - status = "okay"; - }; - timer@1 { - status = "okay"; - }; -}; - -&timers8 { - /delete-property/dmas; - /delete-property/dma-names; - status = "disabled"; - pwm { - pinctrl-0 = <&pwm8_pins_a>; - pinctrl-1 = <&pwm8_sleep_pins_a>; - pinctrl-names = "default", "sleep"; - status = "okay"; - }; - timer@7 { - status = "okay"; - }; -}; - -&timers12 { - /delete-property/dmas; - /delete-property/dma-names; - status = "disabled"; - pwm { - pinctrl-0 = <&pwm12_pins_a>; - pinctrl-1 = <&pwm12_sleep_pins_a>; - pinctrl-names = "default", "sleep"; - status = "okay"; - }; - timer@11 { - status = "okay"; - }; -}; - -&usart3 { - pinctrl-names = "default", "sleep", "idle"; - pinctrl-0 = <&usart3_pins_b>; - pinctrl-1 = <&usart3_sleep_pins_b>; - pinctrl-2 = <&usart3_idle_pins_b>; - /* - * HW flow control USART3_RTS is optional, and isn't default wired to - * the connector. SB23 needs to be soldered in order to use it, and R77 - * (ETH_CLK) should be removed. - */ - uart-has-rtscts; - status = "disabled"; -}; - -&usbh_ehci { - phys = <&usbphyc_port0>; - status = "okay"; -}; - -&usbotg_hs { - pinctrl-0 = <&usbotg_hs_pins_a>; - pinctrl-names = "default"; - phys = <&usbphyc_port1 0>; - phy-names = "usb2-phy"; - status = "okay"; -}; - -&usbphyc { - status = "okay"; -}; - -&usbphyc_port0 { - st,tune-hs-dc-level = <2>; - st,enable-fs-rftime-tuning; - st,enable-hs-rftime-reduction; - st,trim-hs-current = <15>; - st,trim-hs-impedance = <1>; - st,tune-squelch-level = <3>; - st,tune-hs-rx-offset = <2>; - st,no-lsfs-sc; -}; - -&usbphyc_port1 { - st,tune-hs-dc-level = <2>; - st,enable-fs-rftime-tuning; - st,enable-hs-rftime-reduction; - st,trim-hs-current = <15>; - st,trim-hs-impedance = <1>; - st,tune-squelch-level = <3>; - st,tune-hs-rx-offset = <2>; - st,no-lsfs-sc; -}; |