diff options
Diffstat (limited to 'dts/src/arm/stm32mp157c-lxa-mc1.dts')
| -rw-r--r-- | dts/src/arm/stm32mp157c-lxa-mc1.dts | 252 |
1 files changed, 0 insertions, 252 deletions
diff --git a/dts/src/arm/stm32mp157c-lxa-mc1.dts b/dts/src/arm/stm32mp157c-lxa-mc1.dts deleted file mode 100644 index 1e9bf7eea0..0000000000 --- a/dts/src/arm/stm32mp157c-lxa-mc1.dts +++ /dev/null @@ -1,252 +0,0 @@ -/* SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause) */ -/* - * Copyright (C) 2020 STMicroelectronics - All Rights Reserved - * Copyright (C) 2020 Ahmad Fatoum, Pengutronix - */ - -/dts-v1/; - -#include "stm32mp157.dtsi" -#include "stm32mp15xx-osd32.dtsi" -#include "stm32mp15xxac-pinctrl.dtsi" - -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/pwm/pwm.h> - -/ { - model = "Linux Automation MC-1 board"; - compatible = "lxa,stm32mp157c-mc1", "oct,stm32mp15xx-osd32", "st,stm32mp157"; - - aliases { - ethernet0 = ðernet0; - mmc0 = &sdmmc1; - mmc1 = &sdmmc2; - serial0 = &uart4; - }; - - backlight: backlight { - compatible = "pwm-backlight"; - pwms = <&backlight_pwm 1 100000 PWM_POLARITY_INVERTED>; - brightness-levels = <0 31 63 95 127 159 191 223 255>; - default-brightness-level = <7>; - power-supply = <®_5v2>; /* 3V3_BACKLIGHT */ - }; - - chosen { - stdout-path = &uart4; - }; - - led-controller-0 { - compatible = "gpio-leds"; - - led-0 { - label = "mc1:green:act"; - gpios = <&gpioa 13 GPIO_ACTIVE_LOW>; - linux,default-trigger = "heartbeat"; - }; - }; - - led-controller-1 { - compatible = "pwm-leds"; - - /* led-1 to led-3 are part of a single RGB led */ - led-1 { - label = "mc1:red:rgb"; - pwms = <&leds_pwm 1 1000000 0>; - max-brightness = <255>; - active-low; - }; - - led-2 { - label = "mc1:green:rgb"; - pwms = <&leds_pwm 2 1000000 0>; - max-brightness = <255>; - active-low; - }; - - led-3 { - label = "mc1:blue:rgb"; - pwms = <&leds_pwm 3 1000000 0>; - max-brightness = <255>; - active-low; - }; - }; - - panel: panel { - compatible = "edt,etm0700g0edh6", "simple-panel"; - backlight = <&backlight>; - enable-gpios = <&gpiod 4 GPIO_ACTIVE_HIGH>; - power-supply = <®_3v3>; - - port { - panel_input: endpoint { - remote-endpoint = <<dc_ep0_out>; - }; - }; - }; - - reg_3v3: regulator_3v3 { - compatible = "regulator-fixed"; - regulator-name = "3V3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - vin-supply = <&v3v3>; - }; - - /* supplied by either debug board or PoE */ - reg_5v2: regulator_5v2 { - compatible = "regulator-fixed"; - regulator-name = "5V2"; - regulator-min-microvolt = <5200000>; - regulator-max-microvolt = <5200000>; - regulator-always-on; - }; -}; - -ðernet0 { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <ðernet0_rgmii_pins_b>; - pinctrl-1 = <ðernet0_rgmii_sleep_pins_b>; - phy-mode = "rgmii-id"; - phy-handle = <ðphy>; - status = "okay"; - - mdio0 { - compatible = "snps,dwmac-mdio"; - #address-cells = <1>; - #size-cells = <0>; - - ethphy: ethernet-phy@3 { /* KSZ9031RN */ - reg = <3>; - reset-gpios = <&gpiog 0 GPIO_ACTIVE_LOW>; /* ETH_RST# */ - interrupt-parent = <&gpioa>; - interrupts = <6 IRQ_TYPE_EDGE_FALLING>; /* ETH_MDINT# */ - reset-assert-us = <10000>; - reset-deassert-us = <300>; - micrel,force-master; - }; - }; -}; - -&gpioz { - gpio-line-names = "HWID0", "HWID1", "HWID2", "HWID3", "", "", - "HWID4", "HWID5"; -}; - -&i2c5 { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&i2c5_pins_b>; - pinctrl-1 = <&i2c5_sleep_pins_b>; - clock-frequency = <400000>; - status = "okay"; - - touchscreen@38 { - compatible = "edt,edt-ft5x06"; - interrupt-parent = <&gpiod>; - interrupts = <11 IRQ_TYPE_EDGE_FALLING>; /* TOUCH_INT# */ - vcc-supply = <®_3v3>; - reg = <0x38>; - reset-gpios = <&gpiof 8 GPIO_ACTIVE_LOW>; /* TOUCH_RESET# */ - touchscreen-size-x = <1792>; - touchscreen-size-y = <1024>; - wakeup-source; - }; -}; - -<dc { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <<dc_pins_c>; - pinctrl-1 = <<dc_sleep_pins_c>; - status = "okay"; - - port { - ltdc_ep0_out: endpoint@0 { - reg = <0>; - remote-endpoint = <&panel_input>; - }; - }; -}; - -&pmic { - regulators { - buck4-supply = <®_5v2>; /* VIN */ - ldo2-supply = <®_5v2>; /* PMIC_LDO25IN */ - ldo5-supply = <®_5v2>; /* PMIC_LDO25IN */ - boost-supply = <®_5v2>; /* PMIC_BSTIN */ - pwr_sw2-supply = <&bst_out>; /* PMIC_SWIN */ - }; -}; - -&sdmmc1 { - pinctrl-names = "default", "opendrain", "sleep"; - pinctrl-0 = <&sdmmc1_b4_pins_a>; - pinctrl-1 = <&sdmmc1_b4_od_pins_a>; - pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; - bus-width = <4>; - cd-gpios = <&gpioh 3 GPIO_ACTIVE_LOW>; - disable-wp; - no-1-8-v; - st,neg-edge; - vmmc-supply = <®_3v3>; - status = "okay"; -}; - -&sdmmc1_b4_pins_a { - /* - * board lacks external pull-ups on SDMMC lines. Class 10 SD refuses to - * work, thus enable internal pull-ups. - */ - pins1 { - /delete-property/ bias-disable; - bias-pull-up; - }; - pins2 { - /delete-property/ bias-disable; - bias-pull-up; - }; -}; - -&sdmmc2 { - pinctrl-names = "default", "opendrain", "sleep"; - pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>; - pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_b>; - pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_b>; - bus-width = <8>; - mmc-ddr-3_3v; - no-1-8-v; - no-sd; - no-sdio; - non-removable; - st,neg-edge; - vmmc-supply = <®_3v3>; - status = "okay"; -}; - -&timers3 { - status = "okay"; - - backlight_pwm: pwm { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&pwm3_pins_b>; - pinctrl-1 = <&pwm3_sleep_pins_b>; - status = "okay"; - }; -}; - -&timers5 { - status = "okay"; - - leds_pwm: pwm { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&pwm5_pins_b>; - pinctrl-1 = <&pwm5_sleep_pins_b>; - status = "okay"; - }; -}; - -&uart4 { - pinctrl-names = "default"; - pinctrl-0 = <&uart4_pins_a>; - status = "okay"; -}; |