diff options
Diffstat (limited to 'dts/src/arm/sun8i-a83t-bananapi-m3.dts')
| -rw-r--r-- | dts/src/arm/sun8i-a83t-bananapi-m3.dts | 169 |
1 files changed, 160 insertions, 9 deletions
diff --git a/dts/src/arm/sun8i-a83t-bananapi-m3.dts b/dts/src/arm/sun8i-a83t-bananapi-m3.dts index 2bafd7e99e..c606af3dbf 100644 --- a/dts/src/arm/sun8i-a83t-bananapi-m3.dts +++ b/dts/src/arm/sun8i-a83t-bananapi-m3.dts @@ -44,7 +44,6 @@ /dts-v1/; #include "sun8i-a83t.dtsi" -#include "sunxi-common-regulators.dtsi" #include <dt-bindings/gpio/gpio.h> @@ -59,6 +58,27 @@ chosen { stdout-path = "serial0:115200n8"; }; + + reg_usb1_vbus: reg-usb1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb1-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + enable-active-high; + gpio = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */ + }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + clocks = <&ac100_rtc 1>; + clock-names = "ext_clock"; + /* The WiFi low power clock must be 32768 Hz */ + assigned-clocks = <&ac100_rtc 1>; + assigned-clock-rates = <32768>; + /* enables internal regulator and de-asserts reset */ + reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */ + }; }; &ehci0 { @@ -71,17 +91,35 @@ &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>; - vmmc-supply = <®_vcc3v3>; + vmmc-supply = <®_dcdc1>; bus-width = <4>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ cd-inverted; status = "okay"; }; +&mmc1 { + vmmc-supply = <®_dldo1>; + vqmmc-supply = <®_dldo1>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; + + brcmf: wifi@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + interrupt-parent = <&r_pio>; + interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "host-wake"; + }; +}; + &mmc2 { pinctrl-names = "default"; pinctrl-0 = <&mmc2_8bit_emmc_pins>; - vmmc-supply = <®_vcc3v3>; + vmmc-supply = <®_dcdc1>; + vqmmc-supply = <®_dcdc1>; bus-width = <8>; non-removable; cap-mmc-hw-reset; @@ -96,6 +134,10 @@ reg = <0x3a3>; interrupt-parent = <&r_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + eldoin-supply = <®_dcdc1>; + fldoin-supply = <®_dcdc5>; + swin-supply = <®_dcdc1>; + x-powers,drive-vbus-en; }; ac100: codec@e89 { @@ -123,17 +165,126 @@ }; }; -®_usb1_vbus { - gpio = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */ +#include "axp81x.dtsi" + +®_aldo1 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-1v8"; +}; + +®_aldo2 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "dram-pll"; +}; + +®_aldo3 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + +®_dcdc1 { + /* schematics says 3.1V but FEX file says 3.3V */ + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-3v3"; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpua"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpub"; +}; + +®_dcdc4 { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-gpu"; +}; + +®_dcdc5 { + regulator-always-on; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vcc-dram"; +}; + +®_dcdc6 { + regulator-always-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-name = "vdd-sys"; +}; + +®_dldo1 { + /* + * This powers both the WiFi/BT module's main power, I/O supply, + * and external pull-ups on all the data lines. It should be set + * to the same voltage as the I/O supply (DCDC1 in this case) to + * avoid any leakage or mismatch. + */ + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi"; +}; + +®_dldo3 { + regulator-always-on; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-name = "vcc-pd"; +}; + +®_drivevbus { + regulator-name = "usb0-vbus"; status = "okay"; }; -®_vcc3v0 { - status = "disabled"; +®_fldo1 { + regulator-min-microvolt = <1080000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vdd12-hsic"; +}; + +®_fldo2 { + /* + * Despite the embedded CPUs core not being used in any way, + * this must remain on or the system will hang. + */ + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpus"; +}; + +®_rtc_ldo { + regulator-name = "vcc-rtc"; }; -®_vcc5v0 { - status = "disabled"; +®_sw { + /* + * The PHY requires 20ms after all voltages + * are applied until core logic is ready and + * 30ms after the reset pin is de-asserted. + * Set a 100ms delay to account for PMIC + * ramp time and board traces. + */ + regulator-enable-ramp-delay = <100000>; + regulator-name = "vcc-ephy"; }; &uart0 { |