diff options
Diffstat (limited to 'dts/src/arm64/marvell/cn9132-db.dts')
| -rw-r--r-- | dts/src/arm64/marvell/cn9132-db.dts | 218 |
1 files changed, 6 insertions, 212 deletions
diff --git a/dts/src/arm64/marvell/cn9132-db.dts b/dts/src/arm64/marvell/cn9132-db.dts index 81fba024b2..1f2e6377af 100644 --- a/dts/src/arm64/marvell/cn9132-db.dts +++ b/dts/src/arm64/marvell/cn9132-db.dts @@ -5,224 +5,18 @@ * Device tree for the CN9132-DB board. */ -#include "cn9131-db.dts" +#include "cn9132-db.dtsi" / { - model = "Marvell Armada CN9132-DB"; - compatible = "marvell,cn9132", "marvell,cn9131", "marvell,cn9130", - "marvell,armada-ap807-quad", "marvell,armada-ap807"; - - aliases { - gpio5 = &cp2_gpio1; - gpio6 = &cp2_gpio2; - ethernet5 = &cp2_eth0; - }; - - cp2_reg_usb3_vbus0: cp2_usb3_vbus@0 { - compatible = "regulator-fixed"; - regulator-name = "cp2-xhci0-vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - gpio = <&cp2_gpio1 2 GPIO_ACTIVE_HIGH>; - }; - - cp2_usb3_0_phy0: cp2_usb3_phy0 { - compatible = "usb-nop-xceiv"; - vcc-supply = <&cp2_reg_usb3_vbus0>; - }; - - cp2_reg_usb3_vbus1: cp2_usb3_vbus@1 { - compatible = "regulator-fixed"; - regulator-name = "cp2-xhci1-vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - gpio = <&cp2_gpio1 3 GPIO_ACTIVE_HIGH>; - }; - - cp2_usb3_0_phy1: cp2_usb3_phy1 { - compatible = "usb-nop-xceiv"; - vcc-supply = <&cp2_reg_usb3_vbus1>; - }; - - cp2_reg_sd_vccq: cp2_sd_vccq@0 { - compatible = "regulator-gpio"; - regulator-name = "cp2_sd_vcc"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - gpios = <&cp2_gpio2 17 GPIO_ACTIVE_HIGH>; - states = <1800000 0x1 3300000 0x0>; - }; - - cp2_sfp_eth0: sfp-eth0 { - compatible = "sff,sfp"; - i2c-bus = <&cp2_sfpp0_i2c>; - los-gpio = <&cp2_module_expander1 11 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&cp2_module_expander1 10 GPIO_ACTIVE_LOW>; - tx-disable-gpio = <&cp2_module_expander1 9 GPIO_ACTIVE_HIGH>; - tx-fault-gpio = <&cp2_module_expander1 8 GPIO_ACTIVE_HIGH>; - /* - * SFP cages are unconnected on early PCBs because of an the I2C - * lanes not being connected. Prevent the port for being - * unusable by disabling the SFP node. - */ - status = "disabled"; - }; + model = "Marvell Armada CN9132-DB setup A"; }; -/* - * Instantiate the second slave CP115 +/* Setup A has SPI1 flash as a boot device, while setup B uses NAND flash. + * Since CP0 SPI1 and CP0 NAND are sharing some pins, they cannot be activated + * simultaneously. When SPI controller is enabled, NAND should be disabled. */ -#define CP11X_NAME cp2 -#define CP11X_BASE f6000000 -#define CP11X_PCIEx_MEM_BASE(iface) (0xe5000000 + (iface * 0x1000000)) -#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000 -#define CP11X_PCIE0_BASE f6600000 -#define CP11X_PCIE1_BASE f6620000 -#define CP11X_PCIE2_BASE f6640000 - -#include "armada-cp115.dtsi" - -#undef CP11X_NAME -#undef CP11X_BASE -#undef CP11X_PCIEx_MEM_BASE -#undef CP11X_PCIEx_MEM_SIZE -#undef CP11X_PCIE0_BASE -#undef CP11X_PCIE1_BASE -#undef CP11X_PCIE2_BASE - -&cp2_crypto { - status = "disabled"; -}; - -&cp2_ethernet { +&cp0_spi1 { status = "okay"; }; -/* SLM-1521-V2, CON9 */ -&cp2_eth0 { - status = "disabled"; - phy-mode = "10gbase-kr"; - /* Generic PHY, providing serdes lanes */ - phys = <&cp2_comphy4 0>; - managed = "in-band-status"; - sfp = <&cp2_sfp_eth0>; -}; - -&cp2_gpio1 { - status = "okay"; -}; - -&cp2_gpio2 { - status = "okay"; -}; - -&cp2_i2c0 { - clock-frequency = <100000>; - - /* SLM-1521-V2 - U3 */ - i2c-mux@72 { - compatible = "nxp,pca9544"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x72>; - cp2_sfpp0_i2c: i2c@0 { - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - }; - - i2c@1 { - #address-cells = <1>; - #size-cells = <0>; - reg = <1>; - /* U12 */ - cp2_module_expander1: pca9555@21 { - compatible = "nxp,pca9555"; - pinctrl-names = "default"; - gpio-controller; - #gpio-cells = <2>; - reg = <0x21>; - }; - }; - }; -}; - -/* SLM-1521-V2, CON6 */ -&cp2_pcie0 { - status = "okay"; - num-lanes = <2>; - num-viewport = <8>; - /* Generic PHY, providing serdes lanes */ - phys = <&cp2_comphy0 0 - &cp2_comphy1 0>; -}; - -/* SLM-1521-V2, CON8 */ -&cp2_pcie2 { - status = "okay"; - num-lanes = <1>; - num-viewport = <8>; - /* Generic PHY, providing serdes lanes */ - phys = <&cp2_comphy5 2>; -}; - -&cp2_sata0 { - status = "okay"; - - /* SLM-1521-V2, CON4 */ - sata-port@0 { - /* Generic PHY, providing serdes lanes */ - phys = <&cp2_comphy2 0>; - }; -}; - -/* CON 2 on SLM-1683 - microSD */ -&cp2_sdhci0 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&cp2_sdhci_pins>; - bus-width = <4>; - cd-gpios = <&cp2_gpio2 23 GPIO_ACTIVE_LOW>; - vqmmc-supply = <&cp2_reg_sd_vccq>; -}; - -&cp2_syscon0 { - cp2_pinctrl: pinctrl { - compatible = "marvell,cp115-standalone-pinctrl"; - - cp2_i2c0_pins: cp2-i2c-pins-0 { - marvell,pins = "mpp37", "mpp38"; - marvell,function = "i2c0"; - }; - cp2_sdhci_pins: cp2-sdhi-pins-0 { - marvell,pins = "mpp56", "mpp57", "mpp58", - "mpp59", "mpp60", "mpp61"; - marvell,function = "sdio"; - }; - }; -}; - -&cp2_utmi { - status = "okay"; -}; - -&cp2_usb3_0 { - status = "okay"; - usb-phy = <&cp2_usb3_0_phy0>; - phys = <&cp2_utmi0>; - phy-names = "usb"; - dr_mode = "host"; -}; - -/* SLM-1521-V2, CON11 */ -&cp2_usb3_1 { - status = "okay"; - usb-phy = <&cp2_usb3_0_phy1>; - /* Generic PHY, providing serdes lanes */ - phys = <&cp2_comphy3 1>, <&cp2_utmi1>; - phy-names = "usb", "utmi"; - dr_mode = "host"; -}; |