diff options
Diffstat (limited to 'dts/src/arm64/qcom/sa8155p-adp.dts')
-rw-r--r-- | dts/src/arm64/qcom/sa8155p-adp.dts | 143 |
1 files changed, 73 insertions, 70 deletions
diff --git a/dts/src/arm64/qcom/sa8155p-adp.dts b/dts/src/arm64/qcom/sa8155p-adp.dts index ba547ca9fc..5e4287f8c8 100644 --- a/dts/src/arm64/qcom/sa8155p-adp.dts +++ b/dts/src/arm64/qcom/sa8155p-adp.dts @@ -7,7 +7,7 @@ #include <dt-bindings/regulator/qcom,rpmh-regulator.h> #include <dt-bindings/gpio/gpio.h> -#include "sm8150.dtsi" +#include "sa8155p.dtsi" #include "pmm8155au_1.dtsi" #include "pmm8155au_2.dtsi" @@ -17,13 +17,14 @@ aliases { serial0 = &uart2; + serial1 = &uart9; }; chosen { stdout-path = "serial0:115200n8"; }; - vreg_3p3: vreg_3p3_regulator { + vreg_3p3: vreg-3p3-regulator { compatible = "regulator-fixed"; regulator-name = "vreg_3p3"; regulator-min-microvolt = <3300000>; @@ -43,37 +44,13 @@ regulator-always-on; regulator-boot-on; - regulator-allow-set-load; vin-supply = <&vreg_3p3>; }; - - mtl_rx_setup: rx-queues-config { - snps,rx-queues-to-use = <1>; - snps,rx-sched-sp; - - queue0 { - snps,dcb-algorithm; - snps,map-to-dma-channel = <0x0>; - snps,route-up; - snps,priority = <0x1>; - }; - }; - - mtl_tx_setup: tx-queues-config { - snps,tx-queues-to-use = <1>; - snps,tx-sched-wrr; - - queue0 { - snps,weight = <0x10>; - snps,dcb-algorithm; - snps,priority = <0x0>; - }; - }; }; &apps_rsc { - pmm8155au-1-rpmh-regulators { + regulators-0 { compatible = "qcom,pmm8155au-rpmh-regulators"; qcom,pmic-id = "a"; @@ -137,6 +114,8 @@ regulator-max-microvolt = <880000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; }; vreg_l7a_1p8: ldo7 { @@ -152,6 +131,8 @@ regulator-max-microvolt = <2960000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; }; vreg_l11a_0p8: ldo11 { @@ -198,7 +179,7 @@ }; }; - pmm8155au-2-rpmh-regulators { + regulators-1 { compatible = "qcom,pmm8155au-rpmh-regulators"; qcom,pmic-id = "c"; @@ -258,6 +239,8 @@ regulator-max-microvolt = <1200000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; }; vreg_l7c_1p8: ldo7 { @@ -273,6 +256,8 @@ regulator-max-microvolt = <1200000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; }; vreg_l10c_3p3: ldo10 { @@ -333,9 +318,6 @@ snps,reset-active-low; snps,reset-delays-us = <0 11000 70000>; - snps,ptp-ref-clk-rate = <250000000>; - snps,ptp-req-clk-rate = <96000000>; - snps,mtl-rx-config = <&mtl_rx_setup>; snps,mtl-tx-config = <&mtl_tx_setup>; @@ -347,19 +329,40 @@ max-speed = <1000>; mdio { - #address-cells = <0x1>; - #size-cells = <0x0>; - compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; /* Micrel KSZ9031RNZ PHY */ rgmii_phy: phy@7 { + compatible = "ethernet-phy-ieee802.3-c22"; reg = <0x7>; - interrupt-parent = <&tlmm>; - interrupts-extended = <&tlmm 124 IRQ_TYPE_EDGE_FALLING>; /* phy intr */ + interrupts-extended = <&tlmm 124 IRQ_TYPE_EDGE_FALLING>; device_type = "ethernet-phy"; - compatible = "ethernet-phy-ieee802.3-c22"; + }; + }; + + mtl_rx_setup: rx-queues-config { + snps,rx-queues-to-use = <1>; + snps,rx-sched-sp; + + queue0 { + snps,dcb-algorithm; + snps,map-to-dma-channel = <0x0>; + snps,route-up; + snps,priority = <0x1>; + }; + }; + + mtl_tx_setup: tx-queues-config { + snps,tx-queues-to-use = <1>; + snps,tx-sched-wrr; + + queue0 { + snps,weight = <0x10>; + snps,dcb-algorithm; + snps,priority = <0x0>; }; }; }; @@ -389,13 +392,17 @@ vmmc-supply = <&vreg_l17a_2p96>; /* Card power line */ bus-width = <4>; no-sdio; - no-emmc; + no-mmc; }; &uart2 { status = "okay"; }; +&uart9 { + status = "okay"; +}; + &ufs_mem_hc { status = "okay"; @@ -480,26 +487,26 @@ &tlmm { gpio-reserved-ranges = <0 4>; - sdc2_on: sdc2_on { - clk { + sdc2_on: sdc2-on-state { + clk-pins { pins = "sdc2_clk"; bias-disable; /* No pull */ drive-strength = <16>; /* 16 MA */ }; - cmd { + cmd-pins { pins = "sdc2_cmd"; bias-pull-up; /* pull up */ drive-strength = <16>; /* 16 MA */ }; - data { + data-pins { pins = "sdc2_data"; bias-pull-up; /* pull up */ drive-strength = <16>; /* 16 MA */ }; - sd-cd { + sd-cd-pins { pins = "gpio96"; function = "gpio"; bias-pull-up; /* pull up */ @@ -507,26 +514,26 @@ }; }; - sdc2_off: sdc2_off { - clk { + sdc2_off: sdc2-off-state { + clk-pins { pins = "sdc2_clk"; bias-disable; /* No pull */ drive-strength = <2>; /* 2 MA */ }; - cmd { + cmd-pins { pins = "sdc2_cmd"; bias-pull-up; /* pull up */ drive-strength = <2>; /* 2 MA */ }; - data { + data-pins { pins = "sdc2_data"; bias-pull-up; /* pull up */ drive-strength = <2>; /* 2 MA */ }; - sd-cd { + sd-cd-pins { pins = "gpio96"; function = "gpio"; bias-pull-up; /* pull up */ @@ -534,66 +541,62 @@ }; }; - usb2phy_ac_en1_default: usb2phy_ac_en1_default { - mux { - pins = "gpio113"; - function = "usb2phy_ac"; - bias-disable; - drive-strength = <2>; - }; + usb2phy_ac_en1_default: usb2phy-ac-en1-default-state { + pins = "gpio113"; + function = "usb2phy_ac"; + bias-disable; + drive-strength = <2>; }; - usb2phy_ac_en2_default: usb2phy_ac_en2_default { - mux { - pins = "gpio123"; - function = "usb2phy_ac"; - bias-disable; - drive-strength = <2>; - }; + usb2phy_ac_en2_default: usb2phy-ac-en2-default-state { + pins = "gpio123"; + function = "usb2phy_ac"; + bias-disable; + drive-strength = <2>; }; - ethernet_defaults: ethernet-defaults { - mdc { + ethernet_defaults: ethernet-defaults-state { + mdc-pins { pins = "gpio7"; function = "rgmii"; bias-pull-up; }; - mdio { + mdio-pins { pins = "gpio59"; function = "rgmii"; bias-pull-up; }; - rgmii-rx { + rgmii-rx-pins { pins = "gpio117", "gpio118", "gpio119", "gpio120", "gpio115", "gpio116"; function = "rgmii"; bias-disable; drive-strength = <2>; }; - rgmii-tx { + rgmii-tx-pins { pins = "gpio122", "gpio4", "gpio5", "gpio6", "gpio114", "gpio121"; function = "rgmii"; bias-pull-up; drive-strength = <16>; }; - phy-intr { + phy-intr-pins { pins = "gpio124"; function = "emac_phy"; bias-disable; drive-strength = <8>; }; - pps { + pps-pins { pins = "gpio81"; function = "emac_pps"; bias-disable; drive-strength = <8>; }; - phy-reset { + phy-reset-pins { pins = "gpio79"; function = "gpio"; bias-pull-up; |