summaryrefslogtreecommitdiffstats
path: root/dts/src/arm64/qcom/sc7180-idp.dts
diff options
context:
space:
mode:
Diffstat (limited to 'dts/src/arm64/qcom/sc7180-idp.dts')
-rw-r--r--dts/src/arm64/qcom/sc7180-idp.dts315
1 files changed, 157 insertions, 158 deletions
diff --git a/dts/src/arm64/qcom/sc7180-idp.dts b/dts/src/arm64/qcom/sc7180-idp.dts
index acdb36f447..0146fb0036 100644
--- a/dts/src/arm64/qcom/sc7180-idp.dts
+++ b/dts/src/arm64/qcom/sc7180-idp.dts
@@ -11,6 +11,7 @@
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
#include "sc7180.dtsi"
+#include "sc7180-firmware-tfa.dtsi"
#include "pm6150.dtsi"
#include "pm6150l.dtsi"
@@ -80,11 +81,17 @@
reg = <0x0 0x94400000 0x0 0x200000>;
no-map;
};
+
+ mdata_mem: mpss-metadata {
+ alloc-ranges = <0x0 0xa0000000 0x0 0x20000000>;
+ size = <0x0 0x4000>;
+ no-map;
+ };
};
};
&apps_rsc {
- pm6150-rpmh-regulators {
+ regulators-0 {
compatible = "qcom,pm6150-rpmh-regulators";
qcom,pmic-id = "a";
@@ -206,7 +213,7 @@
};
};
- pm6150l-rpmh-regulators {
+ regulators-1 {
compatible = "qcom,pm6150l-rpmh-regulators";
qcom,pmic-id = "c";
@@ -289,7 +296,11 @@
};
};
-&dsi0 {
+&mdss {
+ status = "okay";
+};
+
+&mdss_dsi0 {
status = "okay";
vdda-supply = <&vreg_l3c_1p2>;
@@ -304,16 +315,11 @@
pinctrl-names = "default";
pinctrl-0 = <&disp_pins>;
- reset-gpios = <&pm6150l_gpio 3 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&pm6150l_gpios 3 GPIO_ACTIVE_HIGH>;
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
- port@0 {
- reg = <0>;
- panel0_in: endpoint {
- remote-endpoint = <&dsi0_out>;
- };
+ port {
+ panel0_in: endpoint {
+ remote-endpoint = <&mdss_dsi0_out>;
};
};
};
@@ -328,16 +334,9 @@
};
};
-&dsi_phy {
- status = "okay";
-};
-
-&mdp {
- status = "okay";
-};
-
-&mdss {
+&mdss_dsi0_phy {
status = "okay";
+ vdds-supply = <&vreg_l4a_0p8>;
};
&qfprom {
@@ -347,7 +346,7 @@
&qspi {
status = "okay";
pinctrl-names = "default";
- pinctrl-0 = <&qspi_clk &qspi_cs0 &qspi_data01>;
+ pinctrl-0 = <&qspi_clk>, <&qspi_cs0>, <&qspi_data0>, <&qspi_data1>;
flash@0 {
compatible = "jedec,spi-nor";
@@ -369,8 +368,31 @@
&remoteproc_mpss {
status = "okay";
compatible = "qcom,sc7180-mss-pil";
+ reg = <0 0x04080000 0 0x4040>, <0 0x04180000 0 0x48>;
+ reg-names = "qdsp6", "rmb";
+
+ clocks = <&gcc GCC_MSS_CFG_AHB_CLK>,
+ <&gcc GCC_MSS_Q6_MEMNOC_AXI_CLK>,
+ <&gcc GCC_MSS_NAV_AXI_CLK>,
+ <&gcc GCC_MSS_SNOC_AXI_CLK>,
+ <&gcc GCC_MSS_MFAB_AXIS_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "iface", "bus", "nav", "snoc_axi", "mnoc_axi", "xo";
+
iommus = <&apps_smmu 0x461 0x0>, <&apps_smmu 0x444 0x3>;
- memory-region = <&mba_mem &mpss_mem>;
+ memory-region = <&mba_mem>, <&mpss_mem>, <&mdata_mem>;
+
+ resets = <&aoss_reset AOSS_CC_MSS_RESTART>,
+ <&pdc_reset PDC_MODEM_SYNC_RESET>;
+ reset-names = "mss_restart", "pdc_reset";
+
+ qcom,halt-regs = <&tcsr_regs_1 0x3000 0x5000 0x4000>;
+ qcom,spare-regs = <&tcsr_regs_2 0xb3e4>;
+};
+
+&scm {
+ /* TF-A firmware maps memory cached so mark dma-coherent to match. */
+ dma-coherent;
};
&sdhc_1 {
@@ -389,7 +411,7 @@
pinctrl-names = "default","sleep";
pinctrl-0 = <&sdc2_on>;
pinctrl-1 = <&sdc2_off>;
- vmmc-supply = <&vreg_l9c_2p9>;
+ vmmc-supply = <&vreg_l9c_2p9>;
vqmmc-supply = <&vreg_l6c_2p9>;
cd-gpios = <&tlmm 69 GPIO_ACTIVE_LOW>;
@@ -405,7 +427,7 @@
pinctrl-names = "default", "sleep";
pinctrl-1 = <&qup_uart3_sleep>;
- bluetooth: wcn3990-bt {
+ bluetooth: bluetooth {
compatible = "qcom,wcn3990-bt";
vddio-supply = <&vreg_l10a_1p8>;
vddxo-supply = <&vreg_l1c_1p8>;
@@ -466,8 +488,8 @@
/* PINCTRL - additions to nodes defined in sc7180.dtsi */
-&pm6150l_gpio {
- disp_pins: disp-pins {
+&pm6150l_gpios {
+ disp_pins: disp-state {
pinconf {
pins = "gpio3";
function = PMIC_GPIO_FUNC_FUNC1;
@@ -480,287 +502,264 @@
};
&qspi_clk {
- pinconf {
- pins = "gpio63";
- bias-disable;
- };
+ bias-disable;
};
&qspi_cs0 {
- pinconf {
- pins = "gpio68";
- bias-disable;
- };
+ bias-disable;
};
-&qspi_data01 {
- pinconf {
- pins = "gpio64", "gpio65";
+&qspi_data0 {
+ bias-pull-up;
+};
- /* High-Z when no transfers; nice to park the lines */
- bias-pull-up;
- };
+&qspi_data1 {
+ bias-pull-up;
};
&qup_i2c2_default {
- pinconf {
- pins = "gpio15", "gpio16";
- drive-strength = <2>;
+ drive-strength = <2>;
- /* Has external pullup */
- bias-disable;
- };
+ /* Has external pullup */
+ bias-disable;
};
&qup_i2c4_default {
- pinconf {
- pins = "gpio115", "gpio116";
- drive-strength = <2>;
+ drive-strength = <2>;
- /* Has external pullup */
- bias-disable;
- };
+ /* Has external pullup */
+ bias-disable;
};
&qup_i2c7_default {
- pinconf {
- pins = "gpio6", "gpio7";
- drive-strength = <2>;
+ drive-strength = <2>;
- /* Has external pullup */
- bias-disable;
- };
+ /* Has external pullup */
+ bias-disable;
};
&qup_i2c9_default {
- pinconf {
- pins = "gpio46", "gpio47";
- drive-strength = <2>;
+ drive-strength = <2>;
- /* Has external pullup */
- bias-disable;
- };
+ /* Has external pullup */
+ bias-disable;
};
-&qup_uart3_default {
- pinconf-cts {
- /*
- * Configure a pull-down on CTS to match the pull of
- * the Bluetooth module.
- */
- pins = "gpio38";
- bias-pull-down;
- };
+&qup_uart3_cts {
+ /*
+ * Configure a pull-down on CTS to match the pull of
+ * the Bluetooth module.
+ */
+ bias-pull-down;
+};
- pinconf-rts {
- /* We'll drive RTS, so no pull */
- pins = "gpio39";
- drive-strength = <2>;
- bias-disable;
- };
+&qup_uart3_rts {
+ /* We'll drive RTS, so no pull */
+ drive-strength = <2>;
+ bias-disable;
+};
- pinconf-tx {
- /* We'll drive TX, so no pull */
- pins = "gpio40";
- drive-strength = <2>;
- bias-disable;
- };
+&qup_uart3_tx {
+ /* We'll drive TX, so no pull */
+ drive-strength = <2>;
+ bias-disable;
+};
- pinconf-rx {
- /*
- * Configure a pull-up on RX. This is needed to avoid
- * garbage data when the TX pin of the Bluetooth module is
- * in tri-state (module powered off or not driving the
- * signal yet).
- */
- pins = "gpio41";
- bias-pull-up;
- };
+&qup_uart3_rx {
+ /*
+ * Configure a pull-up on RX. This is needed to avoid
+ * garbage data when the TX pin of the Bluetooth module is
+ * in tri-state (module powered off or not driving the
+ * signal yet).
+ */
+ bias-pull-up;
};
-&qup_uart8_default {
- pinconf-tx {
- pins = "gpio44";
- drive-strength = <2>;
- bias-disable;
- };
+&qup_uart8_tx {
+ drive-strength = <2>;
+ bias-disable;
+};
- pinconf-rx {
- pins = "gpio45";
- drive-strength = <2>;
- bias-pull-up;
- };
+&qup_uart8_rx {
+ drive-strength = <2>;
+ bias-pull-up;
};
-&qup_spi0_default {
- pinconf {
- pins = "gpio34", "gpio35", "gpio36", "gpio37";
- drive-strength = <2>;
- bias-disable;
- };
+&qup_spi0_spi {
+ drive-strength = <2>;
+ bias-disable;
};
-&qup_spi6_default {
- pinconf {
- pins = "gpio59", "gpio60", "gpio61", "gpio62";
- drive-strength = <2>;
- bias-disable;
- };
+&qup_spi0_cs {
+ drive-strength = <2>;
+ bias-disable;
};
-&qup_spi10_default {
- pinconf {
- pins = "gpio86", "gpio87", "gpio88", "gpio89";
- drive-strength = <2>;
- bias-disable;
- };
+&qup_spi6_spi {
+ drive-strength = <2>;
+ bias-disable;
};
-&tlmm {
- qup_uart3_sleep: qup-uart3-sleep {
- pinmux {
- pins = "gpio38", "gpio39",
- "gpio40", "gpio41";
- function = "gpio";
- };
+&qup_spi6_cs {
+ drive-strength = <2>;
+ bias-disable;
+};
+
+&qup_spi10_spi {
+ drive-strength = <2>;
+ bias-disable;
+};
- pinconf-cts {
+&qup_spi10_cs {
+ drive-strength = <2>;
+ bias-disable;
+};
+
+&tlmm {
+ qup_uart3_sleep: qup-uart3-sleep-state {
+ cts-pins {
/*
* Configure a pull-down on CTS to match the pull of
* the Bluetooth module.
*/
pins = "gpio38";
+ function = "gpio";
bias-pull-down;
};
- pinconf-rts {
+ rts-pins {
/*
* Configure pull-down on RTS. As RTS is active low
* signal, pull it low to indicate the BT SoC that it
* can wakeup the system anytime from suspend state by
* pulling RX low (by sending wakeup bytes).
*/
- pins = "gpio39";
- bias-pull-down;
+ pins = "gpio39";
+ function = "gpio";
+ bias-pull-down;
};
- pinconf-tx {
+ tx-pins {
/*
* Configure pull-up on TX when it isn't actively driven
* to prevent BT SoC from receiving garbage during sleep.
*/
pins = "gpio40";
+ function = "gpio";
bias-pull-up;
};
- pinconf-rx {
+ rx-pins {
/*
* Configure a pull-up on RX. This is needed to avoid
* garbage data when the TX pin of the Bluetooth module
* is floating which may cause spurious wakeups.
*/
pins = "gpio41";
+ function = "gpio";
bias-pull-up;
};
};
- sdc1_on: sdc1-on {
- pinconf-clk {
+ sdc1_on: sdc1-on-state {
+ clk-pins {
pins = "sdc1_clk";
bias-disable;
drive-strength = <16>;
};
- pinconf-cmd {
+ cmd-pins {
pins = "sdc1_cmd";
bias-pull-up;
drive-strength = <10>;
};
- pinconf-data {
+ data-pins {
pins = "sdc1_data";
bias-pull-up;
drive-strength = <10>;
};
- pinconf-rclk {
+ rclk-pins {
pins = "sdc1_rclk";
bias-pull-down;
};
};
- sdc1_off: sdc1-off {
- pinconf-clk {
+ sdc1_off: sdc1-off-state {
+ clk-pins {
pins = "sdc1_clk";
bias-disable;
drive-strength = <2>;
};
- pinconf-cmd {
+ cmd-pins {
pins = "sdc1_cmd";
bias-pull-up;
drive-strength = <2>;
};
- pinconf-data {
+ data-pins {
pins = "sdc1_data";
bias-pull-up;
drive-strength = <2>;
};
- pinconf-rclk {
+ rclk-pins {
pins = "sdc1_rclk";
bias-pull-down;
};
};
- sdc2_on: sdc2-on {
- pinconf-clk {
+ sdc2_on: sdc2-on-state {
+ clk-pins {
pins = "sdc2_clk";
bias-disable;
drive-strength = <16>;
};
- pinconf-cmd {
+ cmd-pins {
pins = "sdc2_cmd";
bias-pull-up;
drive-strength = <10>;
};
- pinconf-data {
+ data-pins {
pins = "sdc2_data";
bias-pull-up;
drive-strength = <10>;
};
- pinconf-sd-cd {
+ sd-cd-pins {
pins = "gpio69";
+ function = "gpio";
bias-pull-up;
drive-strength = <2>;
};
};
- sdc2_off: sdc2-off {
- pinconf-clk {
+ sdc2_off: sdc2-off-state {
+ clk-pins {
pins = "sdc2_clk";
bias-disable;
drive-strength = <2>;
};
- pinconf-cmd {
+ cmd-pins {
pins = "sdc2_cmd";
bias-pull-up;
drive-strength = <2>;
};
- pinconf-data {
+ data-pins {
pins = "sdc2_data";
bias-pull-up;
drive-strength = <2>;
};
- pinconf-sd-cd {
+ sd-cd-pins {
pins = "gpio69";
+ function = "gpio";
bias-pull-up;
drive-strength = <2>;
};
generated by cgit v1.2.3 (git 2.39.1) at 2024-04-25 08:46:44 +0000