diff options
Diffstat (limited to 'dts/src/arm64/qcom/sc7180-trogdor.dtsi')
| -rw-r--r-- | dts/src/arm64/qcom/sc7180-trogdor.dtsi | 101 |
1 files changed, 2 insertions, 99 deletions
diff --git a/dts/src/arm64/qcom/sc7180-trogdor.dtsi b/dts/src/arm64/qcom/sc7180-trogdor.dtsi index 70c88c37de..d4f4441179 100644 --- a/dts/src/arm64/qcom/sc7180-trogdor.dtsi +++ b/dts/src/arm64/qcom/sc7180-trogdor.dtsi @@ -601,15 +601,6 @@ &dsi0 { status = "okay"; vdda-supply = <&vdda_mipi_dsi0_1p2>; - - ports { - port@1 { - endpoint { - remote-endpoint = <&sn65dsi86_in>; - data-lanes = <0 1 2 3>; - }; - }; - }; }; &dsi_phy { @@ -617,70 +608,6 @@ vdds-supply = <&vdda_mipi_dsi0_pll>; }; -edp_brij_i2c: &i2c2 { - status = "okay"; - clock-frequency = <400000>; - - sn65dsi86_bridge: bridge@2d { - compatible = "ti,sn65dsi86"; - reg = <0x2d>; - pinctrl-names = "default"; - pinctrl-0 = <&edp_brij_en>, <&edp_brij_irq>; - gpio-controller; - #gpio-cells = <2>; - - interrupt-parent = <&tlmm>; - interrupts = <11 IRQ_TYPE_LEVEL_HIGH>; - - enable-gpios = <&tlmm 104 GPIO_ACTIVE_HIGH>; - - vpll-supply = <&pp1800_edp_vpll>; - vccio-supply = <&pp1800_brij_vccio>; - vcca-supply = <&pp1200_brij>; - vcc-supply = <&pp1200_brij>; - - clocks = <&rpmhcc RPMH_LN_BB_CLK3>; - clock-names = "refclk"; - - no-hpd; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - sn65dsi86_in: endpoint { - remote-endpoint = <&dsi0_out>; - }; - }; - - port@1 { - reg = <1>; - sn65dsi86_out: endpoint { - data-lanes = <0 1>; - remote-endpoint = <&panel_in_edp>; - }; - }; - }; - - aux-bus { - panel: panel { - /* Compatible will be filled in per-board */ - power-supply = <&pp3300_dx_edp>; - backlight = <&backlight>; - hpd-gpios = <&sn65dsi86_bridge 2 GPIO_ACTIVE_HIGH>; - - port { - panel_in_edp: endpoint { - remote-endpoint = <&sn65dsi86_out>; - }; - }; - }; - }; - }; -}; - ap_sar_sensor_i2c: &i2c5 { clock-frequency = <400000>; @@ -750,17 +677,6 @@ hp_i2c: &i2c9 { }; }; -&ipa { - status = "okay"; - - /* - * Trogdor doesn't have QHEE (Qualcomm's EL2 blob), so the - * modem needs to cover certain init steps (GSI init), and - * the AP needs to wait for it. - */ - modem-init; -}; - &lpass_cpu { status = "okay"; @@ -1244,19 +1160,6 @@ ap_spi_fp: &spi10 { }; }; - edp_brij_irq: edp-brij-irq { - pinmux { - pins = "gpio11"; - function = "gpio"; - }; - - pinconf { - pins = "gpio11"; - drive-strength = <2>; - bias-pull-down; - }; - }; - en_pp3300_codec: en-pp3300-codec { pinmux { pins = "gpio83"; @@ -1523,13 +1426,13 @@ ap_spi_fp: &spi10 { pinconf-cmd { pins = "sdc1_cmd"; bias-pull-up; - drive-strength = <10>; + drive-strength = <16>; }; pinconf-data { pins = "sdc1_data"; bias-pull-up; - drive-strength = <10>; + drive-strength = <16>; }; pinconf-rclk { |