diff options
Diffstat (limited to 'dts/src/arm64/qcom/sc7280-herobrine-herobrine-r0.dts')
| -rw-r--r-- | dts/src/arm64/qcom/sc7280-herobrine-herobrine-r0.dts | 1352 |
1 files changed, 1352 insertions, 0 deletions
diff --git a/dts/src/arm64/qcom/sc7280-herobrine-herobrine-r0.dts b/dts/src/arm64/qcom/sc7280-herobrine-herobrine-r0.dts new file mode 100644 index 0000000000..1779d96c30 --- /dev/null +++ b/dts/src/arm64/qcom/sc7280-herobrine-herobrine-r0.dts @@ -0,0 +1,1352 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Google Herobrine board device tree source + * + * Copyright 2021 Google LLC. + */ + +/dts-v1/; + +#include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h> +#include <dt-bindings/iio/qcom,spmi-adc7-pmr735a.h> +#include <dt-bindings/input/gpio-keys.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> + +#include "sc7280.dtsi" + +/* PMICs depend on spmi_bus label and so must come after SoC */ +#include "pm7325.dtsi" +#include "pm8350c.dtsi" +#include "pmk8350.dtsi" + +#include "sc7280-chrome-common.dtsi" + +/ { + model = "Google Herobrine (rev0)"; + compatible = "google,herobrine-rev0", "qcom,sc7280"; +}; + +/ { + aliases { + serial0 = &uart5; + serial1 = &uart7; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + /* FIXED REGULATORS - parents above children */ + + /* This is the top level supply and variable voltage */ + ppvar_sys: ppvar-sys-regulator { + compatible = "regulator-fixed"; + regulator-name = "ppvar_sys"; + regulator-always-on; + regulator-boot-on; + }; + + /* This divides ppvar_sys by 2, so voltage is variable */ + src_vph_pwr: src-vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "src_vph_pwr"; + + /* EC turns on with switchcap_on; always on for AP */ + regulator-always-on; + regulator-boot-on; + + vin-supply = <&ppvar_sys>; + }; + + pp5000_s3: pp5000-s3-regulator { + compatible = "regulator-fixed"; + regulator-name = "pp5000_s3"; + + /* EC turns on with en_pp5000_s3; always on for AP */ + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + vin-supply = <&ppvar_sys>; + }; + + pp3300_z1: pp3300-z1-regulator { + compatible = "regulator-fixed"; + regulator-name = "pp3300_z1"; + + /* EC turns on with en_pp3300_z1; always on for AP */ + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + vin-supply = <&ppvar_sys>; + }; + + pp3300_audio: + pp3300_codec: pp3300-codec-regulator { + compatible = "regulator-fixed"; + regulator-name = "pp3300_codec"; + + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 67 GPIO_ACTIVE_HIGH>; + enable-active-high; + pinctrl-names = "default"; + pinctrl-0 = <&en_pp3300_codec>; + + vin-supply = <&pp3300_z1>; + }; + + pp3300_cam: + pp3300_edp: + pp3300_ts: pp3300-edp-regulator { + compatible = "regulator-fixed"; + regulator-name = "pp3300_edp"; + + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 80 GPIO_ACTIVE_HIGH>; + enable-active-high; + pinctrl-names = "default"; + pinctrl-0 = <&en_pp3300_dx_edp>; + + vin-supply = <&pp3300_z1>; + }; + + pp3300_fp: + pp3300_fp_ls: + pp3300_mcu: pp3300-fp-regulator { + compatible = "regulator-fixed"; + regulator-name = "pp3300_fp"; + + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + regulator-boot-on; + regulator-always-on; + + /* + * WARNING: it is intentional that GPIO 42 isn't listed here. + * The userspace script for updating the fingerprint firmware + * needs to control the FP regulators during a FW update, + * hence the signal can't be owned by the kernel regulator. + */ + + pinctrl-names = "default"; + pinctrl-0 = <&en_fp_rails>; + + vin-supply = <&pp3300_z1>; + }; + + pp3300_hub: pp3300-hub-regulator { + compatible = "regulator-fixed"; + regulator-name = "pp3300_hub"; + + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + regulator-boot-on; + regulator-always-on; + + gpio = <&tlmm 24 GPIO_ACTIVE_HIGH>; + enable-active-high; + pinctrl-names = "default"; + pinctrl-0 = <&en_pp3300_hub>; + + vin-supply = <&pp3300_z1>; + }; + + pp3300_tp: pp3300-tp-regulator { + compatible = "regulator-fixed"; + regulator-name = "pp3300_tp"; + + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + /* AP turns on with PP1800_L18B_S0; always on for AP */ + regulator-always-on; + regulator-boot-on; + + vin-supply = <&pp3300_z1>; + }; + + pp2850_uf_cam: pp2850-uf-cam-regulator { + compatible = "regulator-fixed"; + regulator-name = "pp2850_uf_cam"; + + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + + gpio = <&tlmm 6 GPIO_ACTIVE_HIGH>; + enable-active-high; + pinctrl-names = "default"; + pinctrl-0 = <&uf_cam_en>; + + vin-supply = <&pp3300_cam>; + }; + + pp2850_vcm_wf_cam: pp2850-vcm-wf-cam-regulator { + compatible = "regulator-fixed"; + regulator-name = "pp2850_vcm_wf_cam"; + + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + + gpio = <&tlmm 7 GPIO_ACTIVE_HIGH>; + enable-active-high; + pinctrl-names = "default"; + pinctrl-0 = <&wf_cam_en>; + + vin-supply = <&pp3300_cam>; + }; + + pp2850_wf_cam: pp2850-wf-cam-regulator { + compatible = "regulator-fixed"; + regulator-name = "pp2850_wf_cam"; + + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + + gpio = <&tlmm 7 GPIO_ACTIVE_HIGH>; + enable-active-high; + /* + * The pinconf can only be referenced once so we put it on the + * first regulator and comment it out here. + * + * pinctrl-names = "default"; + * pinctrl-0 = <&wf_cam_en>; + */ + + vin-supply = <&pp3300_cam>; + }; + + pp1800_fp: pp1800-fp-regulator { + compatible = "regulator-fixed"; + regulator-name = "pp1800_fp"; + + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-boot-on; + regulator-always-on; + + /* + * WARNING: it is intentional that GPIO 42 isn't listed here. + * The userspace script for updating the fingerprint firmware + * needs to control the FP regulators during a FW update, + * hence the signal can't be owned by the kernel regulator. + */ + + pinctrl-names = "default"; + pinctrl-0 = <&en_fp_rails>; + + vin-supply = <&pp1800_l18b_s0>; + status = "disabled"; + }; + + pp1800_uf_cam: pp1800-uf-cam-regulator { + compatible = "regulator-fixed"; + regulator-name = "pp1800_uf_cam"; + + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + gpio = <&tlmm 6 GPIO_ACTIVE_HIGH>; + enable-active-high; + /* + * The pinconf can only be referenced once so we put it on the + * first regulator and comment it out here. + * + * pinctrl-names = "default"; + * pinctrl-0 = <&uf_cam_en>; + */ + + vin-supply = <&pp1800_l19b>; + }; + + pp1800_wf_cam: pp1800-wf-cam-regulator { + compatible = "regulator-fixed"; + regulator-name = "pp1800_wf_cam"; + + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + gpio = <&tlmm 7 GPIO_ACTIVE_HIGH>; + enable-active-high; + /* + * The pinconf can only be referenced once so we put it on the + * first regulator and comment it out here. + * + * pinctrl-names = "default"; + * pinctrl-0 = <&wf_cam_en>; + */ + + vin-supply = <&pp1800_l19b>; + }; + + pp1200_wf_cam: pp1200-wf-cam-regulator { + compatible = "regulator-fixed"; + regulator-name = "pp1200_wf_cam"; + + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + + gpio = <&tlmm 7 GPIO_ACTIVE_HIGH>; + enable-active-high; + /* + * The pinconf can only be referenced once so we put it on the + * first regulator and comment it out here. + * + * pinctrl-names = "default"; + * pinctrl-0 = <&wf_cam_en>; + */ + + vin-supply = <&pp1200_l6b>; + }; + + /* BOARD-SPECIFIC TOP LEVEL NODES */ + + gpio_keys: gpio-keys { + compatible = "gpio-keys"; + status = "disabled"; + pinctrl-names = "default"; + pinctrl-0 = <&pen_pdct_l>; + + pen_insert: pen-insert { + label = "Pen Insert"; + + /* Insert = low, eject = high */ + gpios = <&tlmm 39 GPIO_ACTIVE_LOW>; + linux,code = <SW_PEN_INSERTED>; + linux,input-type = <EV_SW>; + wakeup-event-action = <EV_ACT_DEASSERTED>; + wakeup-source; + }; + }; + + pwmleds { + compatible = "pwm-leds"; + status = "disabled"; + keyboard_backlight: keyboard-backlight { + status = "disabled"; + label = "cros_ec::kbd_backlight"; + pwms = <&cros_ec_pwm 0>; + max-brightness = <1023>; + }; + }; +}; + +&apps_rsc { + pm7325-regulators { + compatible = "qcom,pm7325-rpmh-regulators"; + qcom,pmic-id = "b"; + + vdd19_pmu_pcie_i: + vdd19_pmu_rfa_i: + vreg_s1b_wlan: + vreg_s1b: smps1 { + regulator-min-microvolt = <1856000>; + regulator-max-microvolt = <2040000>; + }; + + vdd_pmu_aon_i: + vreg_s7b_wlan: + vreg_s7b: smps7 { + regulator-min-microvolt = <535000>; + regulator-max-microvolt = <1120000>; + }; + + vdd13_pmu_pcie_i: + vdd13_pmu_rfa_i: + vreg_s8b_wlan: + vreg_s8b: smps8 { + regulator-min-microvolt = <1256000>; + regulator-max-microvolt = <1500000>; + }; + + vdda_usb_ss_dp_core: + vreg_l1b: ldo1 { + regulator-min-microvolt = <825000>; + regulator-max-microvolt = <925000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdda_usb_hs0_3p1: + vreg_l2b: ldo2 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3544000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pp1200_l6b: + vdd_ufs_1p2: + vdd_vref: + vdda_csi01_1p2: + vdda_csi23_1p2: + vdda_csi4_1p2: + vdda_dsi0_1p2: + vdda_pcie0_1p2: + vdda_pcie1_1p2: + vdda_usb_ss_dp_1p2: + vdda_qlink0_1p2_ck: + vdda_qlink1_1p2_ck: + vreg_l6b_1p2: + vreg_l6b: ldo6 { + regulator-min-microvolt = <1120000>; + regulator-max-microvolt = <1408000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pp2950_l7b: + vreg_l7b: ldo7 { + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + codec_vcc: + pp1800_l18b_s0: + pp1800_ts: + vdd1: + vddpx_0: + vddpx_3: + vddpx_7: + vreg_l18b: ldo18 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pp1800_l19b: + vddpx_ts: + vddpx_wl4otp: + vreg_l19b: ldo19 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + pm8350c-regulators { + compatible = "qcom,pm8350c-rpmh-regulators"; + qcom,pmic-id = "c"; + + vreg_s1c: smps1 { + regulator-min-microvolt = <2190000>; + regulator-max-microvolt = <2210000>; + }; + + vddpx_1: + vreg_s9c: smps9 { + regulator-min-microvolt = <1010000>; + regulator-max-microvolt = <1170000>; + }; + + pp1800_l1c: + pp1800_pen: + vdd_a_gfx_cs_1p1: + vdd_a_cxo_1p8: + vdd_qfprom: + vdda_apc_cs_1p8: + vdda_qrefs_1p8: + vdda_turing_q6_cs_1p8: + vdda_usb_hs0_1p8: + vreg_l1c: ldo1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1980000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + dmic_vdd: + pp1800_alc5682: + pp1800_l2c: + pp1800_vreg_alc5682: + vreg_l2c: ldo2 { + regulator-min-microvolt = <1620000>; + regulator-max-microvolt = <1980000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pp3300_sar: + pp3300_sensor: + vreg_l3c: ldo3 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <3540000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + ppvar_uim1: + vddpx_5: + vreg_l4c: ldo4 { + regulator-min-microvolt = <1620000>; + regulator-max-microvolt = <3300000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pp2950_l5c: + uim_vcc: + vddpx_6: + vreg_l5c: ldo5 { + regulator-min-microvolt = <1620000>; + regulator-max-microvolt = <3300000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + ppvar_l6c: + vddpx_2: + vreg_l6c: ldo6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7c: ldo7 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3544000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pp1800_prox: + pp1800_sar: + vreg_l8c: ldo8 { + regulator-min-microvolt = <1620000>; + regulator-max-microvolt = <2000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pp2950_l9c: + vreg_l9c: ldo9 { + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdd_a_gnss_0p9: + vdd_ufs_core: + vdd_usb_hs0_core: + vdd_vref_0p9: + vdda_csi01_0p9: + vdda_csi23_0p9: + vdda_csi4_0p9: + vdda_dsi0_pll_0p9: + vdda_dsi0_0p9: + vdda_pcie0_core: + vdda_pcie1_core: + vdda_qlink0_0p9: + vdda_qlink1_0p9: + vdda_qlink0_0p9_ck: + vdda_qlink1_0p9_ck: + vdda_qrefs_0p875: + vreg_l10c_0p8: + vreg_l10c: ldo10 { + regulator-min-microvolt = <720000>; + regulator-max-microvolt = <1050000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pp2800_l11c: + vreg_l11c: ldo11 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <3544000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pp1800_l12c: + vreg_l12c: ldo12 { + regulator-min-microvolt = <1650000>; + regulator-max-microvolt = <2000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pp3300_l13c: + vreg_l13c: ldo13 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3544000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_bob: bob { + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; + }; + }; +}; + +ap_tp_i2c: &i2c1 { + status = "okay"; + clock-frequency = <400000>; + + trackpad: trackpad@15 { + compatible = "elan,ekth3000"; + reg = <0x15>; + pinctrl-names = "default"; + pinctrl-0 = <&tp_int_odl>; + + interrupt-parent = <&tlmm>; + interrupts = <102 IRQ_TYPE_EDGE_FALLING>; + + vcc-supply = <&pp3300_z1>; + + wakeup-source; + }; +}; + +ap_h1_i2c: &i2c12 { + status = "okay"; + clock-frequency = <400000>; + + tpm@50 { + compatible = "google,cr50"; + reg = <0x50>; + + pinctrl-names = "default"; + pinctrl-0 = <&h1_ap_int_odl>; + + interrupt-parent = <&tlmm>; + interrupts = <54 IRQ_TYPE_EDGE_RISING>; + }; +}; + +ap_ts_pen: &i2c13 { + status = "okay"; + clock-frequency = <400000>; + + ap_ts: touchscreen@10 { + compatible = "hid-over-i2c"; + reg = <0x10>; + pinctrl-names = "default"; + pinctrl-0 = <&ts_int_l>, <&ts_reset_l>; + + interrupt-parent = <&tlmm>; + interrupts = <81 IRQ_TYPE_LEVEL_LOW>; + + post-power-on-delay-ms = <20>; + hid-descr-addr = <0x0001>; + + vdd-supply = <&pp3300_ts>; + }; +}; + +&pm7325_gpios { + status = "disabled"; /* No GPIOs are connected */ +}; + +&pmk8350_gpios { + status = "disabled"; /* No GPIOs are connected */ +}; + +&pmk8350_rtc { + status = "disabled"; +}; + +&pmk8350_vadc { + pmk8350_die_temp { + reg = <PMK8350_ADC7_DIE_TEMP>; + label = "pmk8350_die_temp"; + qcom,pre-scaling = <1 1>; + }; + + pmr735a_die_temp { + reg = <PMR735A_ADC7_DIE_TEMP>; + label = "pmr735a_die_temp"; + qcom,pre-scaling = <1 1>; + }; +}; + +&qfprom { + vcc-supply = <&vdd_qfprom>; +}; + +&qupv3_id_0 { + status = "okay"; +}; + +&qupv3_id_1 { + status = "okay"; +}; + +&sdhc_1 { + status = "okay"; + + vmmc-supply = <&pp2950_l7b>; + vqmmc-supply = <&pp1800_l19b>; +}; + +&sdhc_2 { + status = "okay"; + + pinctrl-0 = <&sdc2_clk>, <&sdc2_cmd>, <&sdc2_data>, <&sd_cd>; + pinctrl-1 = <&sdc2_clk_sleep>, <&sdc2_cmd_sleep>, <&sdc2_data_sleep>, <&sd_cd>; + vmmc-supply = <&pp2950_l9c>; + vqmmc-supply = <&ppvar_l6c>; + + cd-gpios = <&tlmm 91 GPIO_ACTIVE_LOW>; +}; + +ap_ec_spi: &spi8 { + status = "okay"; + + pinctrl-0 = <&qup_spi8_data_clk>, <&qup_spi8_cs_gpio_init_high>, <&qup_spi8_cs_gpio>; + cs-gpios = <&tlmm 35 GPIO_ACTIVE_LOW>; + + cros_ec: ec@0 { + compatible = "google,cros-ec-spi"; + reg = <0>; + interrupt-parent = <&tlmm>; + interrupts = <142 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&ap_ec_int_l>; + spi-max-frequency = <3000000>; + + cros_ec_pwm: pwm { + compatible = "google,cros-ec-pwm"; + #pwm-cells = <1>; + }; + + i2c_tunnel: i2c-tunnel { + compatible = "google,cros-ec-i2c-tunnel"; + google,remote-bus = <0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + typec { + compatible = "google,cros-ec-typec"; + #address-cells = <1>; + #size-cells = <0>; + + usb_c0: connector@0 { + compatible = "usb-c-connector"; + reg = <0>; + label = "left"; + power-role = "dual"; + data-role = "host"; + try-power-role = "source"; + }; + + usb_c1: connector@1 { + compatible = "usb-c-connector"; + reg = <1>; + label = "right"; + power-role = "dual"; + data-role = "host"; + try-power-role = "source"; + }; + }; + }; +}; + +#include <arm/cros-ec-keyboard.dtsi> +#include <arm/cros-ec-sbs.dtsi> + +&keyboard_controller { + function-row-physmap = < + MATRIX_KEY(0x00, 0x02, 0) /* T1 */ + MATRIX_KEY(0x03, 0x02, 0) /* T2 */ + MATRIX_KEY(0x02, 0x02, 0) /* T3 */ + MATRIX_KEY(0x01, 0x02, 0) /* T4 */ + MATRIX_KEY(0x03, 0x04, 0) /* T5 */ + MATRIX_KEY(0x02, 0x04, 0) /* T6 */ + MATRIX_KEY(0x01, 0x04, 0) /* T7 */ + MATRIX_KEY(0x02, 0x09, 0) /* T8 */ + MATRIX_KEY(0x01, 0x09, 0) /* T9 */ + MATRIX_KEY(0x00, 0x04, 0) /* T10 */ + >; + linux,keymap = < + MATRIX_KEY(0x00, 0x02, KEY_BACK) + MATRIX_KEY(0x03, 0x02, KEY_REFRESH) + MATRIX_KEY(0x02, 0x02, KEY_ZOOM) + MATRIX_KEY(0x01, 0x02, KEY_SCALE) + MATRIX_KEY(0x03, 0x04, KEY_SYSRQ) + MATRIX_KEY(0x02, 0x04, KEY_BRIGHTNESSDOWN) + MATRIX_KEY(0x01, 0x04, KEY_BRIGHTNESSUP) + MATRIX_KEY(0x02, 0x09, KEY_MUTE) + MATRIX_KEY(0x01, 0x09, KEY_VOLUMEDOWN) + MATRIX_KEY(0x00, 0x04, KEY_VOLUMEUP) + + CROS_STD_MAIN_KEYMAP + >; +}; + +&uart5 { + compatible = "qcom,geni-debug-uart"; + status = "okay"; +}; + +&uart7 { + status = "okay"; +}; + +&usb_1 { + status = "okay"; +}; + +&usb_1_dwc3 { + dr_mode = "host"; +}; + +&usb_1_hsphy { + status = "okay"; + + vdda-pll-supply = <&vdd_usb_hs0_core>; + vdda33-supply = <&vdda_usb_hs0_3p1>; + vdda18-supply = <&vdda_usb_hs0_1p8>; +}; + +&usb_1_qmpphy { + status = "okay"; + + vdda-phy-supply = <&vdda_usb_ss_dp_1p2>; + vdda-pll-supply = <&vdda_usb_ss_dp_core>; +}; + +&usb_2 { + status = "okay"; +}; + +&usb_2_dwc3 { + dr_mode = "host"; +}; + +&usb_2_hsphy { + status = "okay"; + + vdda-pll-supply = <&vdd_usb_hs0_core>; + vdda33-supply = <&vdda_usb_hs0_3p1>; + vdda18-supply = <&vdda_usb_hs0_1p8>; +}; + +/* PINCTRL - additions to nodes defined in sc7280.dtsi */ + +&dp_hot_plug_det { + bias-disable; +}; + +&pcie1_clkreq_n { + bias-pull-up; + drive-strength = <2>; +}; + +&qspi_cs0 { + bias-disable; +}; + +&qspi_clk { + bias-disable; +}; + +&qspi_data01 { + /* High-Z when no transfers; nice to park the lines */ + bias-pull-up; +}; + +&qup_uart5_rx { + drive-strength = <2>; + bias-pull-up; +}; + +&qup_uart5_tx { + drive-strength = <2>; + bias-disable; +}; + +&qup_uart7_cts { + /* + * Configure a pull-down on CTS to match the pull of + * the Bluetooth module. + */ + bias-pull-down; +}; + +&qup_uart7_rts { + /* We'll drive RTS, so no pull */ + drive-strength = <2>; + bias-disable; +}; + +&qup_uart7_tx { + /* We'll drive TX, so no pull */ + drive-strength = <2>; + bias-disable; +}; + +&qup_uart7_rx { + /* + * Configure a pull-up on RX. This is needed to avoid + * garbage data when the TX pin of the Bluetooth module is + * in tri-state (module powered off or not driving the + * signal yet). + */ + bias-pull-up; +}; + +&sdc1_clk { + bias-disable; + drive-strength = <16>; +}; + +&sdc1_cmd { + bias-pull-up; + drive-strength = <10>; +}; + +&sdc1_data { + bias-pull-up; + drive-strength = <10>; +}; + +&sdc1_rclk { + bias-pull-down; +}; + +&sdc2_clk { + bias-disable; + drive-strength = <16>; +}; + +&sdc2_cmd { + bias-pull-up; + drive-strength = <10>; +}; + +&sdc2_data { + bias-pull-up; + drive-strength = <10>; +}; + +/* PINCTRL - board-specific pinctrl */ + +&pm8350c_gpios { + gpio-line-names = "AP_SUSPEND", + "", + "", + "AP_BL_EN", + "", + "SD_CD_ODL", + "", + "", + "AP_BL_PWM"; + + ap_bl_en: ap-bl-en { + pins = "gpio4"; + function = "normal"; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; + bias-disable; + + /* Force backlight to be disabled to match state at boot. */ + output-low; + }; +}; + +&tlmm { + gpio-line-names = "HP_I2C_SDA", /* 0 */ + "HP_I2C_SCL", + "SSD_RST_L", + "PE_WAKE_ODL", + "AP_TP_I2C_SDA", + "AP_TP_I2C_SCL", + "UF_CAM_EN", + "WF_CAM_EN", + "AP_SAR_SENSOR_SDA", + "AP_SAR_SENSOR_SCL", + + "", /* 10 */ + "", + "AP_SPI_MOSI", + "AP_SPI_MISO", + "AP_SPI_CLK", + "AP_SPI_CS0_L", + "", + "", + "EDP_HPD", + "", + + "UF_CAM_RST_L", /* 20 */ + "WF_CAM_RST_L", + "UART_AP_TX_DBG_RX", + "UART_DBG_TX_AP_RX", + "EN_PP3300_HUB", + "", + "HOST2WLAN_SOL", + "WLAN2HOST_SOL", + "BT_UART_CTS", + "BT_UART_RTS", + + "BT_UART_TXD", /* 30 */ + "BT_UART_RXD", + "AP_EC_SPI_MISO", + "AP_EC_SPI_MOSI", + "AP_EC_SPI_CLK", + "AP_EC_SPI_CS_L", + "", + "", + "", + "PEN_PDCT_L", + + "IO_BRD_ID0", /* 40 */ + "IO_BRD_ID1", + "EN_FP_RAILS", + "PEN_IRQ_L", + "AP_SPI_FP_MISO", + "AP_SPI_FP_MOSI", + "AP_SPI_FP_CLK", + "AP_SPI_FP_CS_L", + "AP_H1_SPI_MISO", + "AP_H1_SPI_MOSI", + + "AP_H1_SPI_CLK", /* 50 */ + "AP_H1_SPI_CS_L", + "AP_TS_PEN_I2C_SDA", + "AP_TS_PEN_I2C_SCL", + "H1_AP_INT_ODL", + "", + "LCM_RST_1V8_L", + "AMP_EN", + "", + "DP_HOT_PLUG_DET", + + "HUB_RST_L", /* 60 */ + "FP_TO_AP_IRQ_L", + "", + "", + "UF_CAM_MCLK", + "WF_CAM_MCLK", + "IO_BRD_ID2", + "EN_PP3300_CODEC", + "EC_IN_RW_ODL", + "UF_CAM_SDA", + + "UF_CAM_SCL", /* 70 */ + "WF_CAM_SDA", + "WF_CAM_SCL", + "AP_BRD_ID0", + "AP_BRD_ID1", + "AP_BRD_ID2", + "", + "FPMCU_BOOT0", + "FP_RST_L", + "PE_CLKREQ_ODL", + + "EN_EDP_PP3300", /* 80 */ + "TS_INT_L", + "FORCE_USB_BOOT", + "WCD_RST_L", + "WLAN_EN", + "BT_EN", + "WLAN_SW_CTRL", + "PCIE0_RESET_L", + "PCIE0_CLK_REQ_L", + "PCIE0_WAKE_L", + + "AS_EN", /* 90 */ + "SD_CD_ODL", + "", + /* + * AP_FLASH_WP_L is crossystem ABI. Schematics + * call it BIOS_FLASH_WP_L. + */ + "AP_FLASH_WP_L", + "BT_WLAN_SB_CLK", + "BT_WLAN_SB_DATA", + "HP_MCLK", + "HP_BCLK", + "HP_DOUT", + "HP_DIN", + + "HP_LRCLK", /* 100 */ + "HP_IRQ", + "TP_INT_ODL", + "", + "IO_SKU_ID2", + "TS_RESET_L", + "AMP_BCLK", + "AMP_DIN", + "AMP_LRCLK", + "UIM2_DATA", + + "UIM2_CLK", /* 110 */ + "UIM2_RST", + "UIM2_PRESENT", + "UIM1_DATA", + "UIM1_CLK", + "UIM1_RST", + "", + "RFFE0_CLK", + "RFFE0_DATA/BOOT_CONFIG_0", + "RFFE1_CLK", + + "RFFE1_DATA/BOOT_CONFIG_1", /* 120 */ + "RFFE2_CLK", + "RFFE2_DATA/BOOT_CONFIG_2", + "RFFE3_CLK", + "RFFE3_DATA/BOOT_CONFIG_3", + "RFFE4_CLK", + "RFFE4_DATA", + "WCI2_LTE_COEX_RXD", + "WCI2_LTE_COEX_TXD", + "IO_SKU_ID0", + + "IO_SKU_ID1", /* 130 */ + "", + "", + "QLINK0_REQ", + "QLINK0_EN", + "QLINK0_WMSS_RESET_L", + "QLINK1_REQ", + "QLINK1_EN", + "QLINK1_WMSS_RESET_L", + "FORCED_USB_BOOT_POL", + + "", /* 140 */ + "P_SENSOR_INT_L", + "AP_EC_INT_L", + "", + "WCD_SWR_TX_CLK", + "WCD_SWR_TX_DATA_0", + "WCD_SWR_TX_DATA_1", + "WCD_SWR_RX_CLK", + "WCD_SWR_RX_DATA_0", + "WCD_SWR_RX_DATA_1", + + "", /* 150 */ + "", + "", + "", + "", + "", + "", + "", + "WCD_SWR_TX_DATA_2", + "", + + "", /* 160 */ + "", + "", + "", + "", + "", + "", + "", + "", + "", + + "", /* 170 */ + "SENS_UART_TXD", + "SENS_UART_RXD", + "", + "", + ""; + + /* + * pinctrl settings for pins that have no real owners. + */ + pinctrl-names = "default"; + pinctrl-0 = <&bios_flash_wp_l>; + + amp_en: amp-en { + pins = "gpio57"; + function = "gpio"; + bias-pull-down; + }; + + ap_ec_int_l: ap-ec-int-l { + pins = "gpio142"; + input-enable; + bias-pull-up; + }; + + bios_flash_wp_l: bios-flash-wp-l { + pins = "gpio93"; + function = "gpio"; + input-enable; + bias-disable; + }; + + bt_en: bt-en { + pins = "gpio85"; + function = "gpio"; + drive-strength = <2>; + output-low; + bias-pull-down; + }; + + en_fp_rails: en-fp-rails { + pins = "gpio42"; + drive-strength = <2>; + output-high; + bias-disable; + }; + + en_pp3300_codec: en-pp3300-codec { + pins = "gpio67"; + drive-strength = <2>; + bias-disable; + }; + + en_pp3300_dx_edp: en-pp3300-dx-edp { + pins = "gpio80"; + function = "gpio"; + drive-strength = <2>; + /* Has external pulldown */ + bias-disable; + }; + + en_pp3300_hub: en-pp3300-hub { + pins = "gpio24"; + function = "gpio"; + drive-strength = <2>; + /* Has external pulldown */ + bias-disable; + }; + + fp_to_ap_irq_l: fp-to-ap-irq-l { + pins = "gpio61"; + function = "gpio"; + input-enable; + /* Has external pullup */ + bias-disable; + }; + + h1_ap_int_odl: h1-ap-int-odl { + pins = "gpio54"; + function = "gpio"; + input-enable; + bias-pull-up; + }; + + hp_irq: hp-irq { + pins = "gpio101"; + function = "gpio"; + bias-pull-up; + }; + + p_sensor_int_l: p-sensor-int-l { + pins = "gpio141"; + function = "gpio"; + input-enable; + bias-pull-up; + }; + + pen_irq_l: pen-irq-l { + pins = "gpio43"; + function = "gpio"; + /* Has external pullup */ + bias-disable; + }; + + pen_pdct_l: pen-pdct-l { + pins = "gpio39"; + function = "gpio"; + /* Has external pullup */ + bias-disable; + }; + + qup_spi8_cs_gpio_init_high: qup-spi8-cs-gpio-init-high { + pins = "gpio35"; + output-high; + }; + + qup_spi11_cs_gpio_init_high: qup-spi11-cs-gpio-init-high { + pins = "gpio47"; + output-high; + }; + + qup_spi12_cs_gpio_init_high: qup-spi12-cs-gpio-init-high { + pins = "gpio51"; + output-high; + }; + + qup_uart7_sleep_cts: qup-uart7-sleep-cts { + pins = "gpio28"; + function = "gpio"; + /* + * Configure a pull-down on CTS to match the pull of + * the Bluetooth module. + */ + bias-pull-down; + }; + + qup_uart7_sleep_rts: qup-uart7-sleep-rts { + pins = "gpio29"; + function = "gpio"; + /* + * Configure pull-down on RTS. As RTS is active low + * signal, pull it low to indicate the BT SoC that it + * can wakeup the system anytime from suspend state by + * pulling RX low (by sending wakeup bytes). + */ + bias-pull-down; + }; + + qup_uart7_sleep_rx: qup-uart7-sleep-rx { + pins = "gpio31"; + function = "gpio"; + /* + * Configure a pull-up on RX. This is needed to avoid + * garbage data when the TX pin of the Bluetooth module + * is floating which may cause spurious wakeups. + */ + bias-pull-up; + }; + + qup_uart7_sleep_tx: qup-uart7-sleep-tx { + pins = "gpio30"; + function = "gpio"; + /* + * Configure pull-up on TX when it isn't actively driven + * to prevent BT SoC from receiving garbage during sleep. + */ + bias-pull-up; + }; + + sd_cd: sd-cd { + pins = "gpio91"; + function = "gpio"; + bias-pull-up; + }; + + tp_int_odl: tp-int-odl { + pins = "gpio102"; + function = "gpio"; + /* Has external pullup */ + bias-disable; + }; + + ts_int_l: ts-int-l { + pins = "gpio81"; + function = "gpio"; + /* Has external pullup */ + bias-pull-up; + }; + + ts_reset_l: ts-reset-l { + pins = "gpio105"; + function = "gpio"; + /* Has external pullup */ + bias-disable; + drive-strength = <2>; + }; + + uf_cam_en: uf-cam-en { + pins = "gpio6"; + function = "gpio"; + drive-strength = <2>; + /* Has external pulldown */ + bias-disable; + }; + + wf_cam_en: wf-cam-en { + pins = "gpio7"; + function = "gpio"; + drive-strength = <2>; + /* Has external pulldown */ + bias-disable; + }; +}; |