diff options
Diffstat (limited to 'dts/src/arm64/qcom/sdm845-cheza.dtsi')
| -rw-r--r-- | dts/src/arm64/qcom/sdm845-cheza.dtsi | 1326 |
1 files changed, 1326 insertions, 0 deletions
diff --git a/dts/src/arm64/qcom/sdm845-cheza.dtsi b/dts/src/arm64/qcom/sdm845-cheza.dtsi new file mode 100644 index 0000000000..1ebbd568df --- /dev/null +++ b/dts/src/arm64/qcom/sdm845-cheza.dtsi @@ -0,0 +1,1326 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Google Cheza device tree source (common between revisions) + * + * Copyright 2018 Google LLC. + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> +#include "sdm845.dtsi" + +/* PMICs depend on spmi_bus label and so must come after SoC */ +#include "pm8005.dtsi" +#include "pm8998.dtsi" + +/ { + aliases { + bluetooth0 = &bluetooth; + hsuart0 = &uart6; + serial0 = &uart9; + wifi0 = &wifi; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&cros_ec_pwm 0>; + enable-gpios = <&tlmm 37 GPIO_ACTIVE_HIGH>; + power-supply = <&ppvar_sys>; + pinctrl-names = "default"; + pinctrl-0 = <&ap_edp_bklten>; + }; + + /* FIXED REGULATORS - parents above children */ + + /* This is the top level supply and variable voltage */ + ppvar_sys: ppvar-sys-regulator { + compatible = "regulator-fixed"; + regulator-name = "ppvar_sys"; + regulator-always-on; + regulator-boot-on; + }; + + /* This divides ppvar_sys by 2, so voltage is variable */ + src_vph_pwr: src-vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "src_vph_pwr"; + + /* EC turns on with switchcap_on_l; always on for AP */ + regulator-always-on; + regulator-boot-on; + + vin-supply = <&ppvar_sys>; + }; + + pp5000_a: pp5000-a-regulator { + compatible = "regulator-fixed"; + regulator-name = "pp5000_a"; + + /* EC turns on with en_pp5000_a; always on for AP */ + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + vin-supply = <&ppvar_sys>; + }; + + src_vreg_bob: src-vreg-bob-regulator { + compatible = "regulator-fixed"; + regulator-name = "src_vreg_bob"; + + /* EC turns on with vbob_en; always on for AP */ + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3600000>; + regulator-max-microvolt = <3600000>; + + vin-supply = <&ppvar_sys>; + }; + + pp3300_dx_edp: pp3300-dx-edp-regulator { + compatible = "regulator-fixed"; + regulator-name = "pp3300_dx_edp"; + + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 43 GPIO_ACTIVE_HIGH>; + enable-active-high; + pinctrl-names = "default"; + pinctrl-0 = <&en_pp3300_dx_edp>; + }; + + /* + * Apparently RPMh does not provide support for PM8998 S4 because it + * is always-on; model it as a fixed regulator. + */ + src_pp1800_s4a: pm8998-smps4 { + compatible = "regulator-fixed"; + regulator-name = "src_pp1800_s4a"; + + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-always-on; + regulator-boot-on; + + vin-supply = <&src_vph_pwr>; + }; + + /* BOARD-SPECIFIC TOP LEVEL NODES */ + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&pen_eject_odl>; + + pen-insert { + label = "Pen Insert"; + /* Insert = low, eject = high */ + gpios = <&tlmm 119 GPIO_ACTIVE_LOW>; + linux,code = <SW_PEN_INSERTED>; + linux,input-type = <EV_SW>; + wakeup-source; + }; + }; + + panel: panel { + compatible ="innolux,p120zdg-bf1"; + power-supply = <&pp3300_dx_edp>; + backlight = <&backlight>; + no-hpd; + + ports { + panel_in: port { + panel_in_edp: endpoint { + remote-endpoint = <&sn65dsi86_out>; + }; + }; + }; + }; +}; + +/* + * Reserved memory changes + * + * Putting this all together (out of order with the rest of the file) to keep + * all modifications to the memory map (from sdm845.dtsi) in one place. + */ + +/* + * Our mpss_region is 8MB bigger than the default one and that conflicts + * with venus_mem and cdsp_mem. + * + * For venus_mem we'll delete and re-create at a different address. + * + * cdsp_mem isn't used on cheza right now so we won't bother re-creating it; but + * that also means we need to delete cdsp_pas. + */ +/delete-node/ &venus_mem; +/delete-node/ &cdsp_mem; +/delete-node/ &cdsp_pas; + +/* Increase the size from 120 MB to 128 MB */ +&mpss_region { + reg = <0 0x8e000000 0 0x8000000>; +}; + +/* Increase the size from 2MB to 8MB */ +&rmtfs_mem { + reg = <0 0x88f00000 0 0x800000>; +}; + +/ { + reserved-memory { + venus_mem: memory@96000000 { + reg = <0 0x96000000 0 0x500000>; + no-map; + }; + }; +}; + +&qspi { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&qspi_clk &qspi_cs0 &qspi_data01>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + + /* + * In theory chip supports up to 104 MHz and controller up + * to 80 MHz, but above 25 MHz wasn't reliable so we'll use + * that for now. b:117440651 + */ + spi-max-frequency = <25000000>; + spi-tx-bus-width = <2>; + spi-rx-bus-width = <2>; + }; +}; + + +&apps_rsc { + pm8998-rpmh-regulators { + compatible = "qcom,pm8998-rpmh-regulators"; + qcom,pmic-id = "a"; + + vdd-s1-supply = <&src_vph_pwr>; + vdd-s2-supply = <&src_vph_pwr>; + vdd-s3-supply = <&src_vph_pwr>; + vdd-s4-supply = <&src_vph_pwr>; + vdd-s5-supply = <&src_vph_pwr>; + vdd-s6-supply = <&src_vph_pwr>; + vdd-s7-supply = <&src_vph_pwr>; + vdd-s8-supply = <&src_vph_pwr>; + vdd-s9-supply = <&src_vph_pwr>; + vdd-s10-supply = <&src_vph_pwr>; + vdd-s11-supply = <&src_vph_pwr>; + vdd-s12-supply = <&src_vph_pwr>; + vdd-s13-supply = <&src_vph_pwr>; + vdd-l1-l27-supply = <&src_pp1025_s7a>; + vdd-l2-l8-l17-supply = <&src_pp1350_s3a>; + vdd-l3-l11-supply = <&src_pp1025_s7a>; + vdd-l4-l5-supply = <&src_pp1025_s7a>; + vdd-l6-supply = <&src_vph_pwr>; + vdd-l7-l12-l14-l15-supply = <&src_pp2040_s5a>; + vdd-l9-supply = <&src_pp2040_s5a>; + vdd-l10-l23-l25-supply = <&src_vreg_bob>; + vdd-l13-l19-l21-supply = <&src_vreg_bob>; + vdd-l16-l28-supply = <&src_vreg_bob>; + vdd-l18-l22-supply = <&src_vreg_bob>; + vdd-l20-l24-supply = <&src_vreg_bob>; + vdd-l26-supply = <&src_pp1350_s3a>; + vin-lvs-1-2-supply = <&src_pp1800_s4a>; + + src_pp1125_s2a: smps2 { + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + }; + + src_pp1350_s3a: smps3 { + regulator-min-microvolt = <1352000>; + regulator-max-microvolt = <1352000>; + }; + + src_pp2040_s5a: smps5 { + regulator-min-microvolt = <1904000>; + regulator-max-microvolt = <2040000>; + }; + + src_pp1025_s7a: smps7 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1028000>; + }; + + vdd_qusb_hs0: + vdda_hp_pcie_core: + vdda_mipi_csi0_0p9: + vdda_mipi_csi1_0p9: + vdda_mipi_csi2_0p9: + vdda_mipi_dsi0_pll: + vdda_mipi_dsi1_pll: + vdda_qlink_lv: + vdda_qlink_lv_ck: + vdda_qrefs_0p875: + vdda_pcie_core: + vdda_pll_cc_ebi01: + vdda_pll_cc_ebi23: + vdda_sp_sensor: + vdda_ufs1_core: + vdda_ufs2_core: + vdda_usb1_ss_core: + vdda_usb2_ss_core: + src_pp875_l1a: ldo1 { + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vddpx_10: + src_pp1200_l2a: ldo2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + + /* TODO: why??? */ + regulator-always-on; + }; + + pp1000_l3a_sdr845: ldo3 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdd_wcss_cx: + vdd_wcss_mx: + vdda_wcss_pll: + src_pp800_l5a: ldo5 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vddpx_13: + src_pp1800_l6a: ldo6 { + regulator-min-microvolt = <1856000>; + regulator-max-microvolt = <1856000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pp1800_l7a_wcn3990: ldo7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + src_pp1200_l8a: ldo8 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1248000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pp1800_dx_pen: + src_pp1800_l9a: ldo9 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + src_pp1800_l10a: ldo10 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pp1000_l11a_sdr845: ldo11 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1048000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdd_qfprom: + vdd_qfprom_sp: + vdda_apc1_cs_1p8: + vdda_gfx_cs_1p8: + vdda_qrefs_1p8: + vdda_qusb_hs0_1p8: + vddpx_11: + src_pp1800_l12a: ldo12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vddpx_2: + src_pp2950_l13a: ldo13 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + src_pp1800_l14a: ldo14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + src_pp1800_l15a: ldo15 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pp2700_l16a: ldo16 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2704000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + src_pp1300_l17a: ldo17 { + regulator-min-microvolt = <1304000>; + regulator-max-microvolt = <1304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pp2700_l18a: ldo18 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + /* + * NOTE: this rail should have been called + * src_pp3300_l19a in the schematic + */ + src_pp3000_l19a: ldo19 { + regulator-min-microvolt = <3304000>; + regulator-max-microvolt = <3304000>; + + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + src_pp2950_l20a: ldo20 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + src_pp2950_l21a: ldo21 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pp3300_hub: + src_pp3300_l22a: ldo22 { + regulator-min-microvolt = <3304000>; + regulator-max-microvolt = <3304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + /* + * HACK: Should add a usb hub node and driver + * to turn this on and off at suspend/resume time + */ + regulator-boot-on; + regulator-always-on; + }; + + pp3300_l23a_ch1_wcn3990: ldo23 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vdda_qusb_hs0_3p1: + src_pp3075_l24a: ldo24 { + regulator-min-microvolt = <3088000>; + regulator-max-microvolt = <3088000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pp3300_l25a_ch0_wcn3990: ldo25 { + regulator-min-microvolt = <3304000>; + regulator-max-microvolt = <3304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pp1200_hub: + vdda_hp_pcie_1p2: + vdda_hv_ebi0: + vdda_hv_ebi1: + vdda_hv_ebi2: + vdda_hv_ebi3: + vdda_mipi_csi_1p25: + vdda_mipi_dsi0_1p2: + vdda_mipi_dsi1_1p2: + vdda_pcie_1p2: + vdda_ufs1_1p2: + vdda_ufs2_1p2: + vdda_usb1_ss_1p2: + vdda_usb2_ss_1p2: + src_pp1200_l26a: ldo26 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + pp3300_dx_pen: + src_pp3300_l28a: ldo28 { + regulator-min-microvolt = <3304000>; + regulator-max-microvolt = <3304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + src_pp1800_lvs1: lvs1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + src_pp1800_lvs2: lvs2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + }; + + pm8005-rpmh-regulators { + compatible = "qcom,pm8005-rpmh-regulators"; + qcom,pmic-id = "c"; + + vdd-s1-supply = <&src_vph_pwr>; + vdd-s2-supply = <&src_vph_pwr>; + vdd-s3-supply = <&src_vph_pwr>; + vdd-s4-supply = <&src_vph_pwr>; + + src_pp600_s3c: smps3 { + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <600000>; + }; + }; +}; + +&dsi0 { + status = "okay"; + vdda-supply = <&vdda_mipi_dsi0_1p2>; + + ports { + port@1 { + endpoint { + remote-endpoint = <&sn65dsi86_in>; + data-lanes = <0 1 2 3>; + }; + }; + }; +}; + +&dsi0_phy { + status = "okay"; + vdds-supply = <&vdda_mipi_dsi0_pll>; +}; + +edp_brij_i2c: &i2c3 { + status = "okay"; + clock-frequency = <400000>; + + sn65dsi86_bridge: bridge@2d { + compatible = "ti,sn65dsi86"; + reg = <0x2d>; + pinctrl-names = "default"; + pinctrl-0 = <&edp_brij_en &edp_brij_irq>; + + interrupt-parent = <&tlmm>; + interrupts = <10 IRQ_TYPE_LEVEL_HIGH>; + + enable-gpios = <&tlmm 102 GPIO_ACTIVE_HIGH>; + + vpll-supply = <&src_pp1800_s4a>; + vccio-supply = <&src_pp1800_s4a>; + vcca-supply = <&src_pp1200_l2a>; + vcc-supply = <&src_pp1200_l2a>; + + clocks = <&rpmhcc RPMH_LN_BB_CLK2>; + clock-names = "refclk"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + sn65dsi86_in: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + + port@1 { + reg = <1>; + sn65dsi86_out: endpoint { + remote-endpoint = <&panel_in_edp>; + }; + }; + }; + }; +}; + +ap_pen_1v8: &i2c11 { + status = "okay"; + clock-frequency = <400000>; + + digitizer@9 { + compatible = "wacom,w9013", "hid-over-i2c"; + reg = <0x9>; + pinctrl-names = "default"; + pinctrl-0 = <&pen_irq_l>, <&pen_pdct_l>, <&pen_rst_l>; + + vdd-supply = <&pp3300_dx_pen>; + vddl-supply = <&pp1800_dx_pen>; + post-power-on-delay-ms = <100>; + + interrupt-parent = <&tlmm>; + interrupts = <24 IRQ_TYPE_LEVEL_LOW>; + + hid-descr-addr = <0x1>; + }; +}; + +amp_i2c: &i2c12 { + status = "okay"; + clock-frequency = <400000>; +}; + +ap_ts_i2c: &i2c14 { + status = "okay"; + clock-frequency = <400000>; + + touchscreen@10 { + compatible = "elan,ekth3500"; + reg = <0x10>; + pinctrl-names = "default"; + pinctrl-0 = <&ts_int_l &ts_reset_l>; + + interrupt-parent = <&tlmm>; + interrupts = <125 IRQ_TYPE_LEVEL_LOW>; + + vcc33-supply = <&src_pp3300_l28a>; + + reset-gpios = <&tlmm 118 GPIO_ACTIVE_LOW>; + }; +}; + +&lpasscc { + status = "okay"; +}; + +&mdss { + status = "okay"; +}; + +&mdss_mdp { + status = "okay"; +}; + +&qupv3_id_0 { + status = "okay"; +}; + +&qupv3_id_1 { + status = "okay"; +}; + +&sdhc_2 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&sdc2_clk &sdc2_cmd &sdc2_data &sd_cd_odl>; + + vmmc-supply = <&src_pp2950_l21a>; + vqmmc-supply = <&vddpx_2>; + + cd-gpios = <&tlmm 44 GPIO_ACTIVE_LOW>; +}; + +&spi0 { + status = "okay"; +}; + +&spi10 { + status = "okay"; + + cros_ec: ec@0 { + compatible = "google,cros-ec-spi"; + reg = <0>; + interrupt-parent = <&tlmm>; + interrupts = <122 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&ec_ap_int_l>; + spi-max-frequency = <3000000>; + + cros_ec_pwm: ec-pwm { + compatible = "google,cros-ec-pwm"; + #pwm-cells = <1>; + }; + + i2c_tunnel: i2c-tunnel { + compatible = "google,cros-ec-i2c-tunnel"; + google,remote-bus = <0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + pdupdate { + compatible = "google,cros-ec-pd-update"; + }; + }; +}; + +#include <arm/cros-ec-keyboard.dtsi> +#include <arm/cros-ec-sbs.dtsi> + +&uart6 { + status = "okay"; + + bluetooth: wcn3990-bt { + compatible = "qcom,wcn3990-bt"; + vddio-supply = <&src_pp1800_s4a>; + vddxo-supply = <&pp1800_l7a_wcn3990>; + vddrf-supply = <&src_pp1300_l17a>; + vddch0-supply = <&pp3300_l25a_ch0_wcn3990>; + max-speed = <3200000>; + }; +}; + +&uart9 { + status = "okay"; +}; + +&ufs_mem_hc { + status = "okay"; + pinctrl-names = "init", "default"; + pinctrl-0 = <&ufs_dev_reset_assert>; + pinctrl-1 = <&ufs_dev_reset_deassert>; + + vcc-supply = <&src_pp2950_l20a>; + vcc-max-microamp = <600000>; +}; + +&ufs_mem_phy { + status = "okay"; + + vdda-phy-supply = <&vdda_ufs1_core>; + vdda-pll-supply = <&vdda_ufs1_1p2>; +}; + +&usb_1 { + status = "okay"; + + /* We'll use this as USB 2.0 only */ + qcom,select-utmi-as-pipe-clk; +}; + +&usb_1_dwc3 { + /* + * The hardware design intends this port to be hooked up in peripheral + * mode, so we'll hardcode it here. Some details: + * - SDM845 expects only a single Type C connector so it has only one + * native Type C port but cheza has two Type C connectors. + * - The only source of DP is the single native Type C port. + * - On cheza we want to be able to hook DP up to _either_ of the + * two Type C connectors and want to be able to achieve 4 lanes of DP. + * - When you configure a Type C port for 4 lanes of DP you lose USB3. + * - In order to make everything work, the native Type C port is always + * configured as 4-lanes DP so it's always available. + * - The extra USB3 port on SDM845 goes to a USB 3 hub which is then + * sent to the two Type C connectors. + * - The extra USB2 lines from the native Type C port are always + * setup as "peripheral" so that we can mux them over to one connector + * or the other if someone needs the connector configured as a gadget + * (but they only get USB2 speeds). + * + * All the hardware muxes would allow us to hook things up in different + * ways to some potential benefit for static configurations (you could + * achieve extra USB2 bandwidth by using two different ports for the + * two conenctors or possibly even get USB3 peripheral mode), but in + * each case you end up forcing to disconnect/reconnect an in-use + * USB session in some cases depending on what you hotplug into the + * other connector. Thus hardcoding this as peripheral makes sense. + */ + dr_mode = "peripheral"; + + /* + * We always need the high speed pins as 4-lanes DP in case someone + * hotplugs a DP peripheral. Thus limit this port to a max of high + * speed. + */ + maximum-speed = "high-speed"; + + /* + * We don't need the usb3-phy since we run in highspeed mode always, so + * re-define these properties removing the superspeed USB PHY reference. + */ + phys = <&usb_1_hsphy>; + phy-names = "usb2-phy"; +}; + +&usb_1_hsphy { + status = "okay"; + + vdd-supply = <&vdda_usb1_ss_core>; + vdda-pll-supply = <&vdda_qusb_hs0_1p8>; + vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>; + + qcom,imp-res-offset-value = <8>; + qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>; + qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>; + qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>; +}; + +&usb_2 { + status = "okay"; +}; + +&usb_2_dwc3 { + /* We have this hooked up to a hub and we always use in host mode */ + dr_mode = "host"; +}; + +&usb_2_hsphy { + status = "okay"; + + vdd-supply = <&vdda_usb2_ss_core>; + vdda-pll-supply = <&vdda_qusb_hs0_1p8>; + vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>; + + qcom,imp-res-offset-value = <8>; + qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_22_8_MA>; +}; + +&usb_2_qmpphy { + status = "okay"; + + vdda-phy-supply = <&vdda_usb2_ss_1p2>; + vdda-pll-supply = <&vdda_usb2_ss_core>; +}; + +&wifi { + status = "okay"; + + vdd-0.8-cx-mx-supply = <&src_pp800_l5a >; + vdd-1.8-xo-supply = <&pp1800_l7a_wcn3990>; + vdd-1.3-rfa-supply = <&src_pp1300_l17a>; + vdd-3.3-ch0-supply = <&pp3300_l25a_ch0_wcn3990>; +}; + +/* PINCTRL - additions to nodes defined in sdm845.dtsi */ + +&qspi_cs0 { + pinconf { + pins = "gpio90"; + bias-disable; + }; +}; + +&qspi_clk { + pinconf { + pins = "gpio95"; + bias-disable; + }; +}; + +&qspi_data01 { + pinconf { + pins = "gpio91", "gpio92"; + + /* High-Z when no transfers; nice to park the lines */ + bias-pull-up; + }; +}; + +&qup_i2c3_default { + pinconf { + pins = "gpio41", "gpio42"; + drive-strength = <2>; + + /* Has external pullup */ + bias-disable; + }; +}; + +&qup_i2c11_default { + pinconf { + pins = "gpio31", "gpio32"; + drive-strength = <2>; + + /* Has external pullup */ + bias-disable; + }; +}; + +&qup_i2c12_default { + pinconf { + pins = "gpio49", "gpio50"; + drive-strength = <2>; + + /* Has external pullup */ + bias-disable; + }; +}; + +&qup_i2c14_default { + pinconf { + pins = "gpio33", "gpio34"; + drive-strength = <2>; + + /* Has external pullup */ + bias-disable; + }; +}; + +&qup_spi0_default { + pinconf { + pins = "gpio0", "gpio1", "gpio2", "gpio3"; + drive-strength = <2>; + bias-disable; + }; +}; + +&qup_spi5_default { + pinconf { + pins = "gpio85", "gpio86", "gpio87", "gpio88"; + drive-strength = <2>; + bias-disable; + }; +}; + +&qup_spi10_default { + pinconf { + pins = "gpio53", "gpio54", "gpio55", "gpio56"; + drive-strength = <2>; + bias-disable; + }; +}; + +&qup_uart6_default { + /* Change pinmux to all 4 pins since CTS and RTS are connected */ + pinmux { + pins = "gpio45", "gpio46", + "gpio47", "gpio48"; + }; + + pinconf-cts { + /* + * Configure a pull-down on 45 (CTS) to match the pull of + * the Bluetooth module. + */ + pins = "gpio45"; + bias-pull-down; + }; + + pinconf-rts-tx { + /* We'll drive 46 (RTS) and 47 (TX), so no pull */ + pins = "gpio46", "gpio47"; + drive-strength = <2>; + bias-disable; + }; + + pinconf-rx { + /* + * Configure a pull-up on 48 (RX). This is needed to avoid + * garbage data when the TX pin of the Bluetooth module is + * in tri-state (module powered off or not driving the + * signal yet). + */ + pins = "gpio48"; + bias-pull-up; + }; +}; + +&qup_uart9_default { + pinconf-tx { + pins = "gpio4"; + drive-strength = <2>; + bias-disable; + }; + + pinconf-rx { + pins = "gpio5"; + drive-strength = <2>; + bias-pull-up; + }; +}; + +/* PINCTRL - board-specific pinctrl */ +&pm8005_gpio { + gpio-line-names = "", + "", + "SLB", + ""; +}; + +&pm8998_adc { + adc-chan@ADC5_AMUX_THM1_100K_PU { + reg = <ADC5_AMUX_THM1_100K_PU>; + label = "sdm_temp"; + }; + + adc-chan@ADC5_AMUX_THM2_100K_PU { + reg = <ADC5_AMUX_THM2_100K_PU>; + label = "quiet_temp"; + }; + + adc-chan@ADC5_AMUX_THM3_100K_PU { + reg = <ADC5_AMUX_THM3_100K_PU>; + label = "lte_temp_1"; + }; + + adc-chan@ADC5_AMUX_THM4_100K_PU { + reg = <ADC5_AMUX_THM4_100K_PU>; + label = "lte_temp_2"; + }; + + adc-chan@ADC5_AMUX_THM5_100K_PU { + reg = <ADC5_AMUX_THM5_100K_PU>; + label = "charger_temp"; + }; +}; + +&pm8998_gpio { + gpio-line-names = "", + "", + "SW_CTRL", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "CFG_OPT1", + "WCSS_PWR_REQ", + "", + "CFG_OPT2", + "SLB"; +}; + +&tlmm { + /* + * pinctrl settings for pins that have no real owners. + */ + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&bios_flash_wp_r_l>, + <&ap_suspend_l_deassert>; + + pinctrl-1 = <&bios_flash_wp_r_l>, + <&ap_suspend_l_assert>; + + /* + * Hogs prevent usermode from changing the value. A GPIO can be both + * here and in the pinctrl section. + */ + ap-suspend-l-hog { + gpio-hog; + gpios = <126 GPIO_ACTIVE_LOW>; + output-low; + }; + + ap_edp_bklten: ap-edp-bklten { + pinmux { + pins = "gpio37"; + function = "gpio"; + }; + + pinconf { + pins = "gpio37"; + drive-strength = <2>; + bias-disable; + }; + }; + + bios_flash_wp_r_l: bios-flash-wp-r-l { + pinmux { + pins = "gpio128"; + function = "gpio"; + input-enable; + }; + + pinconf { + pins = "gpio128"; + bias-disable; + }; + }; + + ec_ap_int_l: ec-ap-int-l { + pinmux { + pins = "gpio122"; + function = "gpio"; + input-enable; + }; + + pinconf { + pins = "gpio122"; + bias-pull-up; + }; + }; + + edp_brij_en: edp-brij-en { + pinmux { + pins = "gpio102"; + function = "gpio"; + }; + + pinconf { + pins = "gpio102"; + drive-strength = <2>; + bias-disable; + }; + }; + + edp_brij_irq: edp-brij-irq { + pinmux { + pins = "gpio10"; + function = "gpio"; + }; + + pinconf { + pins = "gpio10"; + drive-strength = <2>; + bias-pull-down; + }; + }; + + en_pp3300_dx_edp: en-pp3300-dx-edp { + pinmux { + pins = "gpio43"; + function = "gpio"; + }; + + pinconf { + pins = "gpio43"; + drive-strength = <2>; + bias-disable; + }; + }; + + h1_ap_int_odl: h1-ap-int-odl { + pinmux { + pins = "gpio129"; + function = "gpio"; + input-enable; + }; + + pinconf { + pins = "gpio129"; + bias-pull-up; + }; + }; + + pen_eject_odl: pen-eject-odl { + pinmux { + pins = "gpio119"; + function = "gpio"; + bias-pull-up; + }; + }; + + pen_irq_l: pen-irq-l { + pinmux { + pins = "gpio24"; + function = "gpio"; + }; + + pinconf { + pins = "gpio24"; + + /* Has external pullup */ + bias-disable; + }; + }; + + pen_pdct_l: pen-pdct-l { + pinmux { + pins = "gpio63"; + function = "gpio"; + }; + + pinconf { + pins = "gpio63"; + + /* Has external pullup */ + bias-disable; + }; + }; + + pen_rst_l: pen-rst-l { + pinmux { + pins = "gpio23"; + function = "gpio"; + }; + + pinconf { + pins = "gpio23"; + bias-disable; + drive-strength = <2>; + + /* + * The pen driver doesn't currently support + * driving this reset line. By specifying + * output-high here we're relying on the fact + * that this pin has a default pulldown at boot + * (which makes sure the pen was in reset if it + * was powered) and then we set it high here to + * take it out of reset. Better would be if the + * pen driver could control this and we could + * remove "output-high" here. + */ + output-high; + }; + }; + + sdc2_clk: sdc2-clk { + pinconf { + pins = "sdc2_clk"; + bias-disable; + + /* + * It seems that mmc_test reports errors if drive + * strength is not 16. + */ + drive-strength = <16>; + }; + }; + + sdc2_cmd: sdc2-cmd { + pinconf { + pins = "sdc2_cmd"; + bias-pull-up; + drive-strength = <16>; + }; + }; + + sdc2_data: sdc2-data { + pinconf { + pins = "sdc2_data"; + bias-pull-up; + drive-strength = <16>; + }; + }; + + sd_cd_odl: sd-cd-odl { + pinmux { + pins = "gpio44"; + function = "gpio"; + }; + + pinconf { + pins = "gpio44"; + bias-pull-up; + }; + }; + + ts_int_l: ts-int-l { + pinmux { + pins = "gpio125"; + function = "gpio"; + }; + + pinconf { + pins = "gpio125"; + bias-pull-up; + }; + }; + + ts_reset_l: ts-reset-l { + pinmux { + pins = "gpio118"; + function = "gpio"; + }; + + pinconf { + pins = "gpio118"; + bias-disable; + drive-strength = <2>; + }; + }; + + ufs_dev_reset_assert: ufs_dev_reset_assert { + config { + pins = "ufs_reset"; + bias-pull-down; /* default: pull down */ + /* + * UFS_RESET driver strengths are having + * different values/steps compared to typical + * GPIO drive strengths. + * + * Following table clarifies: + * + * HDRV value | UFS_RESET | Typical GPIO + * (dec) | (mA) | (mA) + * 0 | 0.8 | 2 + * 1 | 1.55 | 4 + * 2 | 2.35 | 6 + * 3 | 3.1 | 8 + * 4 | 3.9 | 10 + * 5 | 4.65 | 12 + * 6 | 5.4 | 14 + * 7 | 6.15 | 16 + * + * POR value for UFS_RESET HDRV is 3 which means + * 3.1mA and we want to use that. Hence just + * specify 8mA to "drive-strength" binding and + * that should result into writing 3 to HDRV + * field. + */ + drive-strength = <8>; /* default: 3.1 mA */ + output-low; /* active low reset */ + }; + }; + + ufs_dev_reset_deassert: ufs_dev_reset_deassert { + config { + pins = "ufs_reset"; + bias-pull-down; /* default: pull down */ + /* + * default: 3.1 mA + * check comments under ufs_dev_reset_assert + */ + drive-strength = <8>; + output-high; /* active low reset */ + }; + }; + + ap_suspend_l_assert: ap_suspend_l_assert { + config { + pins = "gpio126"; + function = "gpio"; + bias-no-pull; + drive-strength = <2>; + output-low; + }; + }; + + ap_suspend_l_deassert: ap_suspend_l_deassert { + config { + pins = "gpio126"; + function = "gpio"; + bias-no-pull; + drive-strength = <2>; + output-high; + }; + }; +}; |