diff options
Diffstat (limited to 'dts/src/arm64/qcom/sdm845-xiaomi-beryllium.dts')
| -rw-r--r-- | dts/src/arm64/qcom/sdm845-xiaomi-beryllium.dts | 565 |
1 files changed, 0 insertions, 565 deletions
diff --git a/dts/src/arm64/qcom/sdm845-xiaomi-beryllium.dts b/dts/src/arm64/qcom/sdm845-xiaomi-beryllium.dts deleted file mode 100644 index c60c8c640e..0000000000 --- a/dts/src/arm64/qcom/sdm845-xiaomi-beryllium.dts +++ /dev/null @@ -1,565 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 - -/dts-v1/; - -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> -#include <dt-bindings/regulator/qcom,rpmh-regulator.h> -#include <dt-bindings/sound/qcom,q6afe.h> -#include <dt-bindings/sound/qcom,q6asm.h> -#include "sdm845.dtsi" -#include "pm8998.dtsi" -#include "pmi8998.dtsi" - -/* - * Delete following upstream (sdm845.dtsi) reserved - * memory mappings which are different in this device. - */ -/delete-node/ &tz_mem; -/delete-node/ &adsp_mem; -/delete-node/ &wlan_msa_mem; -/delete-node/ &mpss_region; -/delete-node/ &venus_mem; -/delete-node/ &cdsp_mem; -/delete-node/ &mba_region; -/delete-node/ &slpi_mem; -/delete-node/ &spss_mem; -/delete-node/ &rmtfs_mem; - -/ { - model = "Xiaomi Pocophone F1"; - compatible = "xiaomi,beryllium", "qcom,sdm845"; - - /* required for bootloader to select correct board */ - qcom,board-id = <69 0>; - qcom,msm-id = <321 0x20001>; - - aliases { - hsuart0 = &uart6; - }; - - gpio-keys { - compatible = "gpio-keys"; - autorepeat; - - pinctrl-names = "default"; - pinctrl-0 = <&vol_up_pin_a>; - - vol-up { - label = "Volume Up"; - linux,code = <KEY_VOLUMEUP>; - gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>; - }; - }; - - /* Reserved memory changes from downstream */ - reserved-memory { - tz_mem: memory@86200000 { - reg = <0 0x86200000 0 0x4900000>; - no-map; - }; - - adsp_mem: memory@8c500000 { - reg = <0 0x8c500000 0 0x1e00000>; - no-map; - }; - - wlan_msa_mem: memory@8e300000 { - reg = <0 0x8e300000 0 0x100000>; - no-map; - }; - - mpss_region: memory@8e400000 { - reg = <0 0x8e400000 0 0x7800000>; - no-map; - }; - - venus_mem: memory@95c00000 { - reg = <0 0x95c00000 0 0x500000>; - no-map; - }; - - cdsp_mem: memory@96100000 { - reg = <0 0x96100000 0 0x800000>; - no-map; - }; - - mba_region: memory@96900000 { - reg = <0 0x96900000 0 0x200000>; - no-map; - }; - - slpi_mem: memory@96b00000 { - reg = <0 0x96b00000 0 0x1400000>; - no-map; - }; - - spss_mem: memory@97f00000 { - reg = <0 0x97f00000 0 0x100000>; - no-map; - }; - - rmtfs_mem: memory@f6301000 { - compatible = "qcom,rmtfs-mem"; - reg = <0 0xf6301000 0 0x200000>; - no-map; - - qcom,client-id = <1>; - qcom,vmid = <15>; - }; - }; - - vreg_s4a_1p8: vreg-s4a-1p8 { - compatible = "regulator-fixed"; - regulator-name = "vreg_s4a_1p8"; - - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - }; -}; - -&adsp_pas { - status = "okay"; - firmware-name = "qcom/sdm845/adsp.mdt"; -}; - -&apps_rsc { - pm8998-rpmh-regulators { - compatible = "qcom,pm8998-rpmh-regulators"; - qcom,pmic-id = "a"; - - vreg_l1a_0p875: ldo1 { - regulator-min-microvolt = <880000>; - regulator-max-microvolt = <880000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; - }; - - vreg_l5a_0p8: ldo5 { - regulator-min-microvolt = <800000>; - regulator-max-microvolt = <800000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; - }; - - vreg_l7a_1p8: ldo7 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; - }; - - vreg_l12a_1p8: ldo12 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; - }; - - vreg_l13a_2p95: ldo13 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <2960000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; - }; - - vreg_l14a_1p8: ldo14 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; - regulator-boot-on; - regulator-always-on; - }; - - vreg_l17a_1p3: ldo17 { - regulator-min-microvolt = <1304000>; - regulator-max-microvolt = <1304000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; - }; - - vreg_l20a_2p95: ldo20 { - regulator-min-microvolt = <2960000>; - regulator-max-microvolt = <2968000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; - }; - - vreg_l21a_2p95: ldo21 { - regulator-min-microvolt = <2960000>; - regulator-max-microvolt = <2968000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; - }; - - vreg_l24a_3p075: ldo24 { - regulator-min-microvolt = <3088000>; - regulator-max-microvolt = <3088000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; - }; - - vreg_l25a_3p3: ldo25 { - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3312000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; - }; - - vreg_l26a_1p2: ldo26 { - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; - regulator-boot-on; - }; - }; -}; - -&cdsp_pas { - status = "okay"; - firmware-name = "qcom/sdm845/cdsp.mdt"; -}; - -&dsi0 { - status = "okay"; - vdda-supply = <&vreg_l26a_1p2>; - - #address-cells = <1>; - #size-cells = <0>; - - panel@0 { - compatible = "tianma,fhd-video"; - reg = <0>; - vddi0-supply = <&vreg_l14a_1p8>; - vddpos-supply = <&lab>; - vddneg-supply = <&ibb>; - - #address-cells = <1>; - #size-cells = <0>; - - reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>; - - port { - tianma_nt36672a_in_0: endpoint { - remote-endpoint = <&dsi0_out>; - }; - }; - }; -}; - -&dsi0_out { - remote-endpoint = <&tianma_nt36672a_in_0>; - data-lanes = <0 1 2 3>; -}; - -&dsi0_phy { - status = "okay"; - vdds-supply = <&vreg_l1a_0p875>; -}; - -&gcc { - protected-clocks = <GCC_QSPI_CORE_CLK>, - <GCC_QSPI_CORE_CLK_SRC>, - <GCC_QSPI_CNOC_PERIPH_AHB_CLK>, - <GCC_LPASS_Q6_AXI_CLK>, - <GCC_LPASS_SWAY_CLK>; -}; - -&gpu { - zap-shader { - memory-region = <&gpu_mem>; - firmware-name = "qcom/sdm845/a630_zap.mbn"; - }; -}; - -&ibb { - regulator-min-microvolt = <4600000>; - regulator-max-microvolt = <6000000>; - regulator-over-current-protection; - regulator-pull-down; - regulator-soft-start; - qcom,discharge-resistor-kohms = <300>; -}; - -&lab { - regulator-min-microvolt = <4600000>; - regulator-max-microvolt = <6000000>; - regulator-over-current-protection; - regulator-pull-down; - regulator-soft-start; -}; - -&mdss { - status = "okay"; -}; - -&mdss_mdp { - status = "okay"; -}; - -&mss_pil { - status = "okay"; - firmware-name = "qcom/sdm845/mba.mbn", "qcom/sdm845/modem.mdt"; -}; - -&pm8998_gpio { - vol_up_pin_a: vol-up-active { - pins = "gpio6"; - function = "normal"; - input-enable; - bias-pull-up; - qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; - }; -}; - -&pm8998_pon { - resin { - compatible = "qcom,pm8941-resin"; - interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>; - debounce = <15625>; - bias-pull-up; - linux,code = <KEY_VOLUMEDOWN>; - }; -}; - -/* QUAT I2S Uses 1 I2S SD Line for audio on TAS2559/60 amplifiers */ -&q6afedai { - qi2s@22 { - reg = <22>; - qcom,sd-lines = <0>; - }; -}; - -&q6asmdai { - dai@0 { - reg = <0>; - }; - - dai@1 { - reg = <1>; - }; - - dai@2 { - reg = <2>; - }; -}; - -&qupv3_id_0 { - status = "okay"; -}; - -&sdhc_2 { - status = "okay"; - - pinctrl-names = "default"; - pinctrl-0 = <&sdc2_default_state &sdc2_card_det_n>; - - vmmc-supply = <&vreg_l21a_2p95>; - vqmmc-supply = <&vreg_l13a_2p95>; - - bus-width = <4>; - cd-gpios = <&tlmm 126 GPIO_ACTIVE_HIGH>; -}; - -&sound { - compatible = "qcom,db845c-sndcard"; - pinctrl-0 = <&quat_mi2s_active - &quat_mi2s_sd0_active>; - pinctrl-names = "default"; - model = "Xiaomi Poco F1"; - audio-routing = - "RX_BIAS", "MCLK", - "AMIC1", "MIC BIAS1", - "AMIC2", "MIC BIAS2", - "AMIC3", "MIC BIAS3"; - - mm1-dai-link { - link-name = "MultiMedia1"; - cpu { - sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>; - }; - }; - - mm2-dai-link { - link-name = "MultiMedia2"; - cpu { - sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>; - }; - }; - - mm3-dai-link { - link-name = "MultiMedia3"; - cpu { - sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>; - }; - }; - - slim-dai-link { - link-name = "SLIM Playback"; - cpu { - sound-dai = <&q6afedai SLIMBUS_0_RX>; - }; - - platform { - sound-dai = <&q6routing>; - }; - - codec { - sound-dai = <&wcd9340 0>; - }; - }; - - slimcap-dai-link { - link-name = "SLIM Capture"; - cpu { - sound-dai = <&q6afedai SLIMBUS_0_TX>; - }; - - platform { - sound-dai = <&q6routing>; - }; - - codec { - sound-dai = <&wcd9340 1>; - }; - }; -}; - -&tlmm { - gpio-reserved-ranges = <0 4>, <81 4>; - - sdc2_default_state: sdc2-default { - clk { - pins = "sdc2_clk"; - bias-disable; - drive-strength = <16>; - }; - - cmd { - pins = "sdc2_cmd"; - bias-pull-up; - drive-strength = <10>; - }; - - data { - pins = "sdc2_data"; - bias-pull-up; - drive-strength = <10>; - }; - }; - - sdc2_card_det_n: sd-card-det-n { - pins = "gpio126"; - function = "gpio"; - bias-pull-up; - }; - - wcd_intr_default: wcd_intr_default { - pins = <54>; - function = "gpio"; - - input-enable; - bias-pull-down; - drive-strength = <2>; - }; -}; - -&uart6 { - status = "okay"; - - bluetooth { - compatible = "qcom,wcn3990-bt"; - - vddio-supply = <&vreg_s4a_1p8>; - vddxo-supply = <&vreg_l7a_1p8>; - vddrf-supply = <&vreg_l17a_1p3>; - vddch0-supply = <&vreg_l25a_3p3>; - max-speed = <3200000>; - }; -}; - -&ufs_mem_hc { - status = "okay"; - - reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>; - - vcc-supply = <&vreg_l20a_2p95>; - vcc-max-microamp = <800000>; -}; - -&ufs_mem_phy { - status = "okay"; - - vdda-phy-supply = <&vreg_l1a_0p875>; - vdda-pll-supply = <&vreg_l26a_1p2>; -}; - -&usb_1 { - status = "okay"; -}; - -&usb_1_dwc3 { - dr_mode = "peripheral"; -}; - -&usb_1_hsphy { - status = "okay"; - - vdd-supply = <&vreg_l1a_0p875>; - vdda-pll-supply = <&vreg_l12a_1p8>; - vdda-phy-dpdm-supply = <&vreg_l24a_3p075>; - - qcom,imp-res-offset-value = <8>; - qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>; - qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>; - qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>; -}; - -&usb_1_qmpphy { - status = "okay"; - - vdda-phy-supply = <&vreg_l26a_1p2>; - vdda-pll-supply = <&vreg_l1a_0p875>; -}; - -&wcd9340{ - pinctrl-0 = <&wcd_intr_default>; - pinctrl-names = "default"; - clock-names = "extclk"; - clocks = <&rpmhcc RPMH_LN_BB_CLK2>; - reset-gpios = <&tlmm 64 0>; - vdd-buck-supply = <&vreg_s4a_1p8>; - vdd-buck-sido-supply = <&vreg_s4a_1p8>; - vdd-tx-supply = <&vreg_s4a_1p8>; - vdd-rx-supply = <&vreg_s4a_1p8>; - vdd-io-supply = <&vreg_s4a_1p8>; - qcom,micbias1-microvolt = <2700000>; - qcom,micbias2-microvolt = <1800000>; - qcom,micbias3-microvolt = <2700000>; - qcom,micbias4-microvolt = <2700000>; -}; - -&wifi { - status = "okay"; - - vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>; - vdd-1.8-xo-supply = <&vreg_l7a_1p8>; - vdd-1.3-rfa-supply = <&vreg_l17a_1p3>; - vdd-3.3-ch0-supply = <&vreg_l25a_3p3>; -}; - -/* PINCTRL - additions to nodes defined in sdm845.dtsi */ - -&qup_uart6_default { - pinmux { - pins = "gpio45", "gpio46", "gpio47", "gpio48"; - function = "qup6"; - }; - - cts { - pins = "gpio45"; - bias-disable; - }; - - rts-tx { - pins = "gpio46", "gpio47"; - drive-strength = <2>; - bias-disable; - }; - - rx { - pins = "gpio48"; - bias-pull-up; - }; -}; |