diff options
Diffstat (limited to 'dts/src/arm64/qcom')
57 files changed, 6764 insertions, 892 deletions
diff --git a/dts/src/arm64/qcom/apq8016-sbc.dtsi b/dts/src/arm64/qcom/apq8016-sbc.dtsi index 6aef0c2e4f..f8d8f3e366 100644 --- a/dts/src/arm64/qcom/apq8016-sbc.dtsi +++ b/dts/src/arm64/qcom/apq8016-sbc.dtsi @@ -414,6 +414,7 @@ &funnel0 { status = "okay"; }; &funnel1 { status = "okay"; }; &replicator { status = "okay"; }; +&stm { status = "okay"; }; &tpiu { status = "okay"; }; &smd_rpm_regulators { diff --git a/dts/src/arm64/qcom/apq8096-ifc6640.dts b/dts/src/arm64/qcom/apq8096-ifc6640.dts index 8c7a27e972..a57c60070c 100644 --- a/dts/src/arm64/qcom/apq8096-ifc6640.dts +++ b/dts/src/arm64/qcom/apq8096-ifc6640.dts @@ -92,6 +92,14 @@ status = "okay"; }; +&hdmi { + status = "okay"; +}; + +&hdmi_phy { + status = "okay"; +}; + &mdss { status = "okay"; }; diff --git a/dts/src/arm64/qcom/ipq6018-cp01-c1.dts b/dts/src/arm64/qcom/ipq6018-cp01-c1.dts index 99cefe88f6..5aec183087 100644 --- a/dts/src/arm64/qcom/ipq6018-cp01-c1.dts +++ b/dts/src/arm64/qcom/ipq6018-cp01-c1.dts @@ -78,3 +78,11 @@ nand-bus-width = <8>; }; }; + +&qusb_phy_1 { + status = "ok"; +}; + +&usb2 { + status = "ok"; +}; diff --git a/dts/src/arm64/qcom/ipq6018.dtsi b/dts/src/arm64/qcom/ipq6018.dtsi index 9fa5b028e4..d2fe58e0eb 100644 --- a/dts/src/arm64/qcom/ipq6018.dtsi +++ b/dts/src/arm64/qcom/ipq6018.dtsi @@ -151,7 +151,7 @@ #size-cells = <2>; ranges; - rpm_msg_ram: memory@0x60000 { + rpm_msg_ram: memory@60000 { reg = <0x0 0x60000 0x0 0x6000>; no-map; }; @@ -258,9 +258,9 @@ reg = <0x0 0x01905000 0x0 0x8000>; }; - tcsr_q6: syscon@1945000 { + tcsr: syscon@1937000 { compatible = "syscon"; - reg = <0x0 0x01945000 0x0 0xe000>; + reg = <0x0 0x01937000 0x0 0x21000>; }; blsp_dma: dma-controller@7884000 { @@ -384,6 +384,105 @@ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; }; + pcie_phy: phy@84000 { + compatible = "qcom,ipq6018-qmp-pcie-phy"; + reg = <0x0 0x84000 0x0 0x1bc>; /* Serdes PLL */ + status = "disabled"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + clocks = <&gcc GCC_PCIE0_AUX_CLK>, + <&gcc GCC_PCIE0_AHB_CLK>; + clock-names = "aux", "cfg_ahb"; + + resets = <&gcc GCC_PCIE0_PHY_BCR>, + <&gcc GCC_PCIE0PHY_PHY_BCR>; + reset-names = "phy", + "common"; + + pcie_phy0: lane@84200 { + reg = <0x0 0x84200 0x0 0x16c>, /* Serdes Tx */ + <0x0 0x84400 0x0 0x200>, /* Serdes Rx */ + <0x0 0x84800 0x0 0x4f4>; /* PCS: Lane0, COM, PCIE */ + #phy-cells = <0>; + + clocks = <&gcc GCC_PCIE0_PIPE_CLK>; + clock-names = "pipe0"; + clock-output-names = "gcc_pcie0_pipe_clk_src"; + #clock-cells = <0>; + }; + }; + + pcie0: pci@20000000 { + compatible = "qcom,pcie-ipq6018"; + reg = <0x0 0x20000000 0x0 0xf1d>, + <0x0 0x20000f20 0x0 0xa8>, + <0x0 0x20001000 0x0 0x1000>, + <0x0 0x80000 0x0 0x4000>, + <0x0 0x20100000 0x0 0x1000>; + reg-names = "dbi", "elbi", "atu", "parf", "config"; + + device_type = "pci"; + linux,pci-domain = <0>; + bus-range = <0x00 0xff>; + num-lanes = <1>; + #address-cells = <3>; + #size-cells = <2>; + + phys = <&pcie_phy0>; + phy-names = "pciephy"; + + ranges = <0x81000000 0 0x20200000 0 0x20200000 + 0 0x10000>, /* downstream I/O */ + <0x82000000 0 0x20220000 0 0x20220000 + 0 0xfde0000>; /* non-prefetchable memory */ + + interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "msi"; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc 0 75 + IRQ_TYPE_LEVEL_HIGH>, /* int_a */ + <0 0 0 2 &intc 0 78 + IRQ_TYPE_LEVEL_HIGH>, /* int_b */ + <0 0 0 3 &intc 0 79 + IRQ_TYPE_LEVEL_HIGH>, /* int_c */ + <0 0 0 4 &intc 0 83 + IRQ_TYPE_LEVEL_HIGH>; /* int_d */ + + clocks = <&gcc GCC_SYS_NOC_PCIE0_AXI_CLK>, + <&gcc GCC_PCIE0_AXI_M_CLK>, + <&gcc GCC_PCIE0_AXI_S_CLK>, + <&gcc GCC_PCIE0_AXI_S_BRIDGE_CLK>, + <&gcc PCIE0_RCHNG_CLK>; + clock-names = "iface", + "axi_m", + "axi_s", + "axi_bridge", + "rchng"; + + resets = <&gcc GCC_PCIE0_PIPE_ARES>, + <&gcc GCC_PCIE0_SLEEP_ARES>, + <&gcc GCC_PCIE0_CORE_STICKY_ARES>, + <&gcc GCC_PCIE0_AXI_MASTER_ARES>, + <&gcc GCC_PCIE0_AXI_SLAVE_ARES>, + <&gcc GCC_PCIE0_AHB_ARES>, + <&gcc GCC_PCIE0_AXI_MASTER_STICKY_ARES>, + <&gcc GCC_PCIE0_AXI_SLAVE_STICKY_ARES>; + reset-names = "pipe", + "sleep", + "sticky", + "axi_m", + "axi_s", + "ahb", + "axi_m_sticky", + "axi_s_sticky"; + + status = "disabled"; + }; + watchdog@b017000 { compatible = "qcom,kpss-wdt"; interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>; @@ -477,7 +576,7 @@ }; q6v5_wcss: remoteproc@cd00000 { - compatible = "qcom,ipq8074-wcss-pil"; + compatible = "qcom,ipq6018-wcss-pil"; reg = <0x0 0x0cd00000 0x0 0x4040>, <0x0 0x004ab000 0x0 0x20>; reg-names = "qdsp6", @@ -504,7 +603,7 @@ clocks = <&gcc GCC_PRNG_AHB_CLK>; clock-names = "prng"; - qcom,halt-regs = <&tcsr_q6 0xa000 0xd000 0x0>; + qcom,halt-regs = <&tcsr 0x18000 0x1b000 0xe000>; qcom,smem-states = <&wcss_smp2p_out 0>, <&wcss_smp2p_out 1>; @@ -524,6 +623,54 @@ }; }; + qusb_phy_1: qusb@59000 { + compatible = "qcom,ipq6018-qusb2-phy"; + reg = <0x0 0x059000 0x0 0x180>; + #phy-cells = <0>; + + clocks = <&gcc GCC_USB1_PHY_CFG_AHB_CLK>, + <&xo>; + clock-names = "cfg_ahb", "ref"; + + resets = <&gcc GCC_QUSB2_1_PHY_BCR>; + status = "disabled"; + }; + + usb2: usb2@7000000 { + compatible = "qcom,ipq6018-dwc3", "qcom,dwc3"; + reg = <0x0 0x070F8800 0x0 0x400>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + clocks = <&gcc GCC_USB1_MASTER_CLK>, + <&gcc GCC_USB1_SLEEP_CLK>, + <&gcc GCC_USB1_MOCK_UTMI_CLK>; + clock-names = "master", + "sleep", + "mock_utmi"; + + assigned-clocks = <&gcc GCC_USB1_MASTER_CLK>, + <&gcc GCC_USB1_MOCK_UTMI_CLK>; + assigned-clock-rates = <133330000>, + <24000000>; + resets = <&gcc GCC_USB1_BCR>; + status = "disabled"; + + dwc_1: usb@7000000 { + compatible = "snps,dwc3"; + reg = <0x0 0x7000000 0x0 0xcd00>; + interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; + phys = <&qusb_phy_1>; + phy-names = "usb2-phy"; + tx-fifo-resize; + snps,is-utmi-l1-suspend; + snps,hird-threshold = /bits/ 8 <0x0>; + snps,dis_u2_susphy_quirk; + snps,dis_u3_susphy_quirk; + dr_mode = "host"; + }; + }; + }; wcss: wcss-smp2p { diff --git a/dts/src/arm64/qcom/ipq8074-hk01.dts b/dts/src/arm64/qcom/ipq8074-hk01.dts index e8c37a1693..cc08dc4eb5 100644 --- a/dts/src/arm64/qcom/ipq8074-hk01.dts +++ b/dts/src/arm64/qcom/ipq8074-hk01.dts @@ -20,7 +20,7 @@ stdout-path = "serial0"; }; - memory { + memory@40000000 { device_type = "memory"; reg = <0x0 0x40000000 0x0 0x20000000>; }; diff --git a/dts/src/arm64/qcom/ipq8074.dtsi b/dts/src/arm64/qcom/ipq8074.dtsi index f39bc10cc5..a620ac0d0b 100644 --- a/dts/src/arm64/qcom/ipq8074.dtsi +++ b/dts/src/arm64/qcom/ipq8074.dtsi @@ -76,6 +76,12 @@ method = "smc"; }; + firmware { + scm { + compatible = "qcom,scm-ipq8074", "qcom,scm"; + }; + }; + soc: soc { #address-cells = <0x1>; #size-cells = <0x1>; @@ -198,6 +204,38 @@ status = "disabled"; }; + prng: rng@e3000 { + compatible = "qcom,prng-ee"; + reg = <0x000e3000 0x1000>; + clocks = <&gcc GCC_PRNG_AHB_CLK>; + clock-names = "core"; + status = "disabled"; + }; + + cryptobam: dma@704000 { + compatible = "qcom,bam-v1.7.0"; + reg = <0x00704000 0x20000>; + interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_CRYPTO_AHB_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <1>; + qcom,controlled-remotely = <1>; + status = "disabled"; + }; + + crypto: crypto@73a000 { + compatible = "qcom,crypto-v5.1"; + reg = <0x0073a000 0x6000>; + clocks = <&gcc GCC_CRYPTO_AHB_CLK>, + <&gcc GCC_CRYPTO_AXI_CLK>, + <&gcc GCC_CRYPTO_CLK>; + clock-names = "iface", "bus", "core"; + dmas = <&cryptobam 2>, <&cryptobam 3>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + tlmm: pinctrl@1000000 { compatible = "qcom,ipq8074-pinctrl"; reg = <0x01000000 0x300000>; @@ -583,10 +621,10 @@ pcie1: pci@10000000 { compatible = "qcom,pcie-ipq8074"; - reg = <0x10000000 0xf1d - 0x10000f20 0xa8 - 0x00088000 0x2000 - 0x10100000 0x1000>; + reg = <0x10000000 0xf1d>, + <0x10000f20 0xa8>, + <0x00088000 0x2000>, + <0x10100000 0x1000>; reg-names = "dbi", "elbi", "parf", "config"; device_type = "pci"; linux,pci-domain = <1>; @@ -645,10 +683,10 @@ pcie0: pci@20000000 { compatible = "qcom,pcie-ipq8074"; - reg = <0x20000000 0xf1d - 0x20000f20 0xa8 - 0x00080000 0x2000 - 0x20100000 0x1000>; + reg = <0x20000000 0xf1d>, + <0x20000f20 0xa8>, + <0x00080000 0x2000>, + <0x20100000 0x1000>; reg-names = "dbi", "elbi", "parf", "config"; device_type = "pci"; linux,pci-domain = <0>; diff --git a/dts/src/arm64/qcom/msm8916-mtp.dts b/dts/src/arm64/qcom/msm8916-mtp.dts index c3f8859231..d66c155387 100644 --- a/dts/src/arm64/qcom/msm8916-mtp.dts +++ b/dts/src/arm64/qcom/msm8916-mtp.dts @@ -9,6 +9,5 @@ / { model = "Qualcomm Technologies, Inc. MSM 8916 MTP"; - compatible = "qcom,msm8916-mtp", "qcom,msm8916-mtp/1", - "qcom,msm8916", "qcom,mtp"; + compatible = "qcom,msm8916-mtp", "qcom,msm8916-mtp/1", "qcom,msm8916"; }; diff --git a/dts/src/arm64/qcom/msm8916-wingtech-wt88047.dts b/dts/src/arm64/qcom/msm8916-wingtech-wt88047.dts new file mode 100644 index 0000000000..4e20cc0008 --- /dev/null +++ b/dts/src/arm64/qcom/msm8916-wingtech-wt88047.dts @@ -0,0 +1,313 @@ +// SPDX-License-Identifier: GPL-2.0-only +// Copyright (C) 2020 Stephan Gerhold + +/dts-v1/; + +#include "msm8916-pm8916.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> + +/ { + model = "Xiaomi Redmi 2 (Wingtech WT88047)"; + compatible = "wingtech,wt88047", "qcom,msm8916"; + + aliases { + serial0 = &blsp1_uart2; + }; + + chosen { + stdout-path = "serial0"; + }; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&gpio_keys_default>; + + label = "GPIO Buttons"; + + volume-up { + label = "Volume Up"; + gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + }; + }; + + usb_id: usb-id { + compatible = "linux,extcon-usb-gpio"; + id-gpio = <&msmgpio 110 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&usb_id_default>; + }; +}; + +&blsp_i2c2 { + status = "okay"; + + imu@68 { + compatible = "invensense,mpu6880"; + reg = <0x68>; + + interrupt-parent = <&msmgpio>; + interrupts = <115 IRQ_TYPE_EDGE_RISING>; + + vdd-supply = <&pm8916_l17>; + vddio-supply = <&pm8916_l6>; + + pinctrl-names = "default"; + pinctrl-0 = <&imu_default>; + + mount-matrix = "1", "0", "0", + "0", "-1", "0", + "0", "0", "1"; + }; +}; + +&blsp_i2c5 { + status = "okay"; + + touchscreen@38 { + /* Likely some other model but works just fine with this one */ + compatible = "edt,edt-ft5506"; + reg = <0x38>; + + interrupt-parent = <&msmgpio>; + interrupts = <13 IRQ_TYPE_EDGE_FALLING>; + + reset-gpios = <&msmgpio 12 GPIO_ACTIVE_LOW>; + + vcc-supply = <&pm8916_l17>; + iovcc-supply = <&pm8916_l6>; + + touchscreen-size-x = <720>; + touchscreen-size-y = <1280>; + + pinctrl-names = "default"; + pinctrl-0 = <&touchscreen_default>; + }; +}; + +&blsp_i2c6 { + status = "okay"; + + led-controller@45 { + compatible = "awinic,aw2013"; + reg = <0x45>; + #address-cells = <1>; + #size-cells = <0>; + + vcc-supply = <&pm8916_l16>; + + led@0 { + reg = <0>; + led-max-microamp = <15000>; + function = LED_FUNCTION_INDICATOR; + color = <LED_COLOR_ID_RED>; + }; + + led@1 { + reg = <1>; + led-max-microamp = <15000>; + function = LED_FUNCTION_INDICATOR; + color = <LED_COLOR_ID_GREEN>; + }; + + led@2 { + reg = <2>; + led-max-microamp = <15000>; + function = LED_FUNCTION_INDICATOR; + color = <LED_COLOR_ID_BLUE>; + }; + }; +}; + +&blsp1_uart2 { + status = "okay"; +}; + +&pm8916_resin { + status = "okay"; + linux,code = <KEY_VOLUMEDOWN>; +}; + +&pm8916_vib { + status = "okay"; +}; + +&pronto { + status = "okay"; +}; + +&sdhc_1 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>; + pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>; +}; + +&sdhc_2 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on>; + pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off>; + + non-removable; +}; + +&usb { + status = "okay"; + extcon = <&usb_id>, <&usb_id>; +}; + +&usb_hs_phy { + extcon = <&usb_id>; +}; + +&smd_rpm_regulators { + vdd_l1_l2_l3-supply = <&pm8916_s3>; + vdd_l4_l5_l6-supply = <&pm8916_s4>; + vdd_l7-supply = <&pm8916_s4>; + + s3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1300000>; + }; + + s4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2100000>; + }; + + l1 { + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1225000>; + }; + + l2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + l4 { + regulator-min-microvolt = <2050000>; + regulator-max-microvolt = <2050000>; + }; + + l5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l8 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2900000>; + }; + + l9 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + l10 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2800000>; + }; + + l11 { + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <2950000>; + regulator-allow-set-load; + regulator-system-load = <200000>; + }; + + l12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + }; + + l13 { + regulator-min-microvolt = <3075000>; + regulator-max-microvolt = <3075000>; + }; + + l14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l15 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l16 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <3300000>; + }; + + l17 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + }; + + l18 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + }; +}; + +&msmgpio { + gpio_keys_default: gpio-keys-default { + pins = "gpio107"; + function = "gpio"; + + drive-strength = <2>; + bias-pull-up; + }; + + imu_default: imu-default { + pins = "gpio115"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + touchscreen_default: touchscreen-default { + pins = "gpio13"; + function = "gpio"; + + drive-strength = <2>; + bias-pull-up; + + reset { + pins = "gpio12"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + }; + + usb_id_default: usb-id-default { + pins = "gpio110"; + function = "gpio"; + + drive-strength = <8>; + bias-pull-up; + }; +}; diff --git a/dts/src/arm64/qcom/msm8916.dtsi b/dts/src/arm64/qcom/msm8916.dtsi index 4f06c0a9c4..3f85e34a8c 100644 --- a/dts/src/arm64/qcom/msm8916.dtsi +++ b/dts/src/arm64/qcom/msm8916.dtsi @@ -489,6 +489,26 @@ <&rpmcc RPM_SMD_SNOC_A_CLK>; }; + stm: stm@802000 { + compatible = "arm,coresight-stm", "arm,primecell"; + reg = <0x00802000 0x1000>, + <0x09280000 0x180000>; + reg-names = "stm-base", "stm-stimulus-base"; + + clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>; + clock-names = "apb_pclk", "atclk"; + + status = "disabled"; + + out-ports { + port { + stm_out: endpoint { + remote-endpoint = <&funnel0_in7>; + }; + }; + }; + }; + /* System CTIs */ /* CTI 0 - TMC connections */ cti0: cti@810000 { @@ -562,6 +582,13 @@ remote-endpoint = <&funnel1_out>; }; }; + + port@7 { + reg = <7>; + funnel0_in7: endpoint { + remote-endpoint = <&stm_out>; + }; + }; }; out-ports { diff --git a/dts/src/arm64/qcom/msm8994.dtsi b/dts/src/arm64/qcom/msm8994.dtsi index f9f0b5aa6a..986fe60dec 100644 --- a/dts/src/arm64/qcom/msm8994.dtsi +++ b/dts/src/arm64/qcom/msm8994.dtsi @@ -15,16 +15,18 @@ chosen { }; clocks { - xo_board: xo_board { + xo_board: xo-board { compatible = "fixed-clock"; #clock-cells = <0>; clock-frequency = <19200000>; + clock-output-names = "xo_board"; }; - sleep_clk: sleep_clk { + sleep_clk: sleep-clk { compatible = "fixed-clock"; #clock-cells = <0>; clock-frequency = <32768>; + clock-output-names = "sleep_clk"; }; }; @@ -430,7 +432,7 @@ power-domains = <&gcc USB30_GDSC>; qcom,select-utmi-as-pipe-clk; - dwc3@f9200000 { + usb@f9200000 { compatible = "snps,dwc3"; reg = <0xf9200000 0xcc00>; interrupts = <0 131 IRQ_TYPE_LEVEL_HIGH>; diff --git a/dts/src/arm64/qcom/msm8996-mtp.dtsi b/dts/src/arm64/qcom/msm8996-mtp.dtsi index 1e1514e915..ac43a91f11 100644 --- a/dts/src/arm64/qcom/msm8996-mtp.dtsi +++ b/dts/src/arm64/qcom/msm8996-mtp.dtsi @@ -20,3 +20,11 @@ }; }; }; + +&hdmi { + status = "okay"; +}; + +&hdmi_phy { + status = "okay"; +}; diff --git a/dts/src/arm64/qcom/msm8996-pmi8996-sony-xperia-tone-dora.dts b/dts/src/arm64/qcom/msm8996-pmi8996-sony-xperia-tone-dora.dts new file mode 100644 index 0000000000..b018693600 --- /dev/null +++ b/dts/src/arm64/qcom/msm8996-pmi8996-sony-xperia-tone-dora.dts @@ -0,0 +1,11 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org> + */ + +#include "msm8996-sony-xperia-tone-dora.dts" +#include "pmi8996.dtsi" + +/ { + model = "Sony Xperia X Performance (PMI8996)"; +}; diff --git a/dts/src/arm64/qcom/msm8996-pmi8996-sony-xperia-tone-kagura.dts b/dts/src/arm64/qcom/msm8996-pmi8996-sony-xperia-tone-kagura.dts new file mode 100644 index 0000000000..842ea3cf55 --- /dev/null +++ b/dts/src/arm64/qcom/msm8996-pmi8996-sony-xperia-tone-kagura.dts @@ -0,0 +1,11 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org> + */ + +#include "msm8996-sony-xperia-tone-kagura.dts" +#include "pmi8996.dtsi" + +/ { + model = "Sony Xperia XZ (PMI8996)"; +}; diff --git a/dts/src/arm64/qcom/msm8996-pmi8996-sony-xperia-tone-keyaki.dts b/dts/src/arm64/qcom/msm8996-pmi8996-sony-xperia-tone-keyaki.dts new file mode 100644 index 0000000000..b3f9062da4 --- /dev/null +++ b/dts/src/arm64/qcom/msm8996-pmi8996-sony-xperia-tone-keyaki.dts @@ -0,0 +1,11 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org> + */ + +#include "msm8996-sony-xperia-tone-keyaki.dts" +#include "pmi8996.dtsi" + +/ { + model = "Sony Xperia XZs (PMI8996)"; +}; diff --git a/dts/src/arm64/qcom/msm8996-sony-xperia-tone-dora.dts b/dts/src/arm64/qcom/msm8996-sony-xperia-tone-dora.dts new file mode 100644 index 0000000000..b4cca54dcb --- /dev/null +++ b/dts/src/arm64/qcom/msm8996-sony-xperia-tone-dora.dts @@ -0,0 +1,27 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2021, AngeloGioacchino Del Regno + * <angelogioacchino.delregno@somainline.org> + * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org> + */ + +/dts-v1/; + +#include "msm8996-sony-xperia-tone.dtsi" + +/ { + model = "Sony Xperia X Performance"; + compatible = "sony,dora-row", "qcom,msm8996"; +}; + +/delete-node/ &tof_sensor; +/delete-node/ &pm8994_l11; +/delete-node/ &pm8994_l14; + +&usb_detect { + pins = "gpio24"; +}; + +&usb3_id { + id-gpio = <&tlmm 24 GPIO_ACTIVE_LOW>; +}; diff --git a/dts/src/arm64/qcom/msm8996-sony-xperia-tone-kagura.dts b/dts/src/arm64/qcom/msm8996-sony-xperia-tone-kagura.dts new file mode 100644 index 0000000000..be6ea855fc --- /dev/null +++ b/dts/src/arm64/qcom/msm8996-sony-xperia-tone-kagura.dts @@ -0,0 +1,15 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2021, AngeloGioacchino Del Regno + * <angelogioacchino.delregno@somainline.org> + * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org> + */ + +/dts-v1/; + +#include "msm8996-sony-xperia-tone.dtsi" + +/ { + model = "Sony Xperia XZ"; + compatible = "sony,kagura-row", "qcom,msm8996"; +}; diff --git a/dts/src/arm64/qcom/msm8996-sony-xperia-tone-keyaki.dts b/dts/src/arm64/qcom/msm8996-sony-xperia-tone-keyaki.dts new file mode 100644 index 0000000000..1eee7d0fc1 --- /dev/null +++ b/dts/src/arm64/qcom/msm8996-sony-xperia-tone-keyaki.dts @@ -0,0 +1,26 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2021, AngeloGioacchino Del Regno + * <angelogioacchino.delregno@somainline.org> + * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org> + */ + +/dts-v1/; + +#include "msm8996-sony-xperia-tone.dtsi" + +/ { + model = "Sony Xperia XZs"; + compatible = "sony,keyaki-row", "qcom,msm8996"; +}; + +&pm8994_l19 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; +}; + +&pm8994_l30 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-pull-down; +}; diff --git a/dts/src/arm64/qcom/msm8996-sony-xperia-tone.dtsi b/dts/src/arm64/qcom/msm8996-sony-xperia-tone.dtsi new file mode 100644 index 0000000000..507396c4d2 --- /dev/null +++ b/dts/src/arm64/qcom/msm8996-sony-xperia-tone.dtsi @@ -0,0 +1,956 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2021, AngeloGioacchino Del Regno + * <angelogioacchino.delregno@somainline.org> + * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org> + */ + +#include "msm8996.dtsi" +#include "pm8994.dtsi" +#include "pmi8994.dtsi" +#include <dt-bindings/input/input.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> +#include <dt-bindings/pinctrl/qcom,pmic-mpp.h> + +/delete-node/ &slpi_region; +/delete-node/ &venus_region; +/delete-node/ &zap_shader_region; + +/ { + qcom,msm-id = <246 0x30001>; /* MSM8996 V3.1 (Final) */ + qcom,pmic-id = <0x20009 0x2000a 0 0>; /* PM8994 + PMI8994 */ + qcom,board-id = <8 0>; + + chosen { + /* + * Due to an unknown-for-a-few-years regression, + * SDHCI only works on MSM8996 in PIO (lame) mode. + */ + bootargs = "sdhci.debug_quirks=0x40 sdhci.debug_quirks2=0x4 maxcpus=2"; + }; + + reserved-memory { + ramoops@a7f00000 { + compatible = "ramoops"; + reg = <0 0xa7f00000 0 0x100000>; + record-size = <0x20000>; + console-size = <0x40000>; + ftrace-size = <0x20000>; + pmsg-size = <0x20000>; + ecc-size = <16>; + }; + + cont_splash_mem: memory@83401000 { + reg = <0 0x83401000 0 0x23ff000>; + no-map; + }; + + zap_shader_region: gpu@90400000 { + compatible = "shared-dma-pool"; + reg = <0x0 0x90400000 0x0 0x2000>; + no-map; + }; + + slpi_region: memory@90500000 { + reg = <0 0x90500000 0 0xa00000>; + no-map; + }; + + venus_region: memory@90f00000 { + reg = <0 0x90f00000 0 0x500000>; + no-map; + }; + }; + + panel_tvdd: tvdd-regulator { + compatible = "regulator-fixed"; + regulator-name = "panel_tvdd"; + gpio = <&tlmm 50 GPIO_ACTIVE_LOW>; + pinctrl-0 = <&tp_vddio_en>; + pinctrl-names = "default"; + }; + + usb3_id: usb3-id { + compatible = "linux,extcon-usb-gpio"; + id-gpio = <&tlmm 25 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&usb_detect>; + }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + regulator-name = "vph_pwr"; + regulator-always-on; + regulator-boot-on; + }; + + wlan_en: wlan-en-1-8v { + compatible = "regulator-fixed"; + regulator-name = "wlan-en-regulator"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&tlmm 84 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&wl_reg_on>; + + /* WLAN card specific delay */ + startup-delay-us = <70000>; + enable-active-high; + }; +}; + +&blsp1_i2c3 { + status = "okay"; + clock-frequency = <355000>; + + tof_sensor: vl53l0x@29 { + compatible = "st,vl53l0x"; + reg = <0x29>; + }; +}; + +&blsp1_uart2 { + status = "okay"; +}; + +&blsp2_i2c5 { + status = "okay"; + clock-frequency = <355000>; + + /* FUSB301 USB-C controller */ +}; + +&blsp2_i2c6 { + status = "okay"; + clock-frequency = <355000>; + + synaptics@2c { + compatible = "syna,rmi4-i2c"; + reg = <0x2c>; + interrupt-parent = <&tlmm>; + interrupts = <125 IRQ_TYPE_EDGE_FALLING>; + vdd-supply = <&panel_tvdd>; + + syna,reset-delay-ms = <220>; + syna,startup-delay-ms = <220>; + #address-cells = <1>; + #size-cells = <0>; + + rmi4-f01@1 { + reg = <0x1>; + syna,nosleep-mode = <1>; + }; + + rmi4-f11@11 { + reg = <0x11>; + syna,sensor-type = <1>; + }; + }; +}; + +&blsp2_uart2 { + status = "okay"; +}; + +&camera0_mclk { + drive-strength = <2>; + output-low; +}; + +&camera0_pwdn { + drive-strength = <2>; + output-low; +}; + +&camera0_rst { + pins = "gpio30"; + drive-strength = <2>; + output-low; +}; + +&camera2_mclk { + drive-strength = <2>; + output-low; +}; + +&camera2_rst { + drive-strength = <2>; + output-low; +}; + +&hsusb_phy1 { + status = "okay"; + + vdda-pll-supply = <&pm8994_l12>; + vdda-phy-dpdm-supply = <&pm8994_l24>; +}; + +&mmcc { + vdd-gfx-supply = <&vdd_gfx>; +}; + +&pcie0 { + status = "okay"; + perst-gpio = <&tlmm 35 GPIO_ACTIVE_LOW>; + wake-gpio = <&tlmm 37 GPIO_ACTIVE_HIGH>; + vddpe-3v3-supply = <&wlan_en>; + vdda-supply = <&pm8994_l28>; +}; + +&pcie_phy { + status = "okay"; + + vdda-phy-supply = <&pm8994_l28>; + vdda-pll-supply = <&pm8994_l12>; +}; + +&pm8994_gpios { + pinctrl-names = "default"; + pinctrl-0 = <&pm8994_gpios_defaults>; + gpio-line-names = + "NC", + "VOL_DOWN_N", + "VOL_UP_N", + "SNAPSHOT_N", + "FOCUS_N", + "NC", + "NFC_VEN", + "NC", + "NC", + "NC", + "NC", + "NC", + "EAR_EN", + "NC", + "PM_DIVCLK1", + "PMI_CLK", + "NC", + "WL_SLEEP_CLK", + "NC", + "PMIC_SPON", + "UIM_BATT_ALARM", + "PMK_SLEEP_CLK"; + + /* + * We don't yet know for sure which GPIOs are of our interest, but what + * we do know is that if a vendor sets the pins to a non-default state, there's + * probably a reason for it, and just to be on the safe side, we follow suit. + */ + pm8994_gpios_defaults: pm8994-gpios-default-state { + pm8994-gpio1-nc { + pins = "gpio1"; + function = PMIC_GPIO_FUNC_NORMAL; + drive-push-pull; + bias-high-impedance; + }; + + vol-down-n { + pins = "gpio2"; + function = PMIC_GPIO_FUNC_NORMAL; + drive-push-pull; + input-enable; + bias-pull-up; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; + power-source = <PM8994_GPIO_S4>; + }; + + vol-up-n { + pins = "gpio3"; + function = PMIC_GPIO_FUNC_NORMAL; + drive-push-pull; + input-enable; + bias-pull-up; + power-source = <PM8994_GPIO_S4>; + }; + + camera-snapshot-n { + pins = "gpio4"; + function = PMIC_GPIO_FUNC_NORMAL; + drive-push-pull; + input-enable; + bias-pull-up; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; + power-source = <PM8994_GPIO_S4>; + }; + + camera-focus-n { + pins = "gpio5"; + function = PMIC_GPIO_FUNC_NORMAL; + drive-push-pull; + input-enable; + bias-pull-up; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; + power-source = <PM8994_GPIO_S4>; + }; + + pm8994-gpio6-nc { + pins = "gpio6"; + function = PMIC_GPIO_FUNC_NORMAL; + drive-push-pull; + bias-high-impedance; + power-source = <PM8994_GPIO_VPH>; + }; + + nfc-download { + pins = "gpio7"; + function = PMIC_GPIO_FUNC_NORMAL; + output-low; + drive-push-pull; + bias-disable; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; + power-source = <PM8994_GPIO_S4>; + }; + + pm8994-gpio8-nc { + pins = "gpio8"; + function = PMIC_GPIO_FUNC_NORMAL; + output-low; + drive-push-pull; + bias-high-impedance; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; + power-source = <PM8994_GPIO_VPH>; + }; + + pm8994-gpio9-nc { + pins = "gpio9"; + function = PMIC_GPIO_FUNC_NORMAL; + output-high; + drive-push-pull; + bias-high-impedance; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; + power-source = <PM8994_GPIO_VPH>; + }; + + nfc-clock { + pins = "gpio10"; + function = PMIC_GPIO_FUNC_NORMAL; + input-enable; + drive-push-pull; + bias-pull-down; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; + power-source = <PM8994_GPIO_S4>; + }; + + pm8994-gpio11-nc { + pins = "gpio11"; + function = PMIC_GPIO_FUNC_NORMAL; + drive-push-pull; + bias-high-impedance; + power-source = <PM8994_GPIO_VPH>; + }; + + pm8994-gpio12-nc { + pins = "gpio12"; + function = PMIC_GPIO_FUNC_NORMAL; + drive-push-pull; + bias-high-impedance; + power-source = <PM8994_GPIO_VPH>; + }; + + ear-enable { + pins = "gpio13"; + function = PMIC_GPIO_FUNC_NORMAL; + output-high; + drive-push-pull; + bias-disable; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; + power-source = <PM8994_GPIO_S4>; + }; + + pm8994-gpio14-nc { + pins = "gpio14"; + function = PMIC_GPIO_FUNC_NORMAL; + drive-push-pull; + input-enable; + bias-high-impedance; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; + power-source = <PM8994_GPIO_VPH>; + }; + + pm-divclk1-gpio { + pins = "gpio15"; + function = "func1"; + output-high; + drive-push-pull; + bias-high-impedance; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; + power-source = <PM8994_GPIO_VPH>; + }; + + pmi-clk-gpio { + pins = "gpio16"; + function = PMIC_GPIO_FUNC_NORMAL; + drive-push-pull; + }; + + pm8994-gpio17-nc { + pins = "gpio17"; + function = PMIC_GPIO_FUNC_NORMAL; + drive-push-pull; + bias-high-impedance; + power-source = <PM8994_GPIO_VPH>; + }; + + rome-sleep { + pins = "gpio18"; + function = PMIC_GPIO_FUNC_FUNC2; + output-low; + drive-push-pull; + bias-disable; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_MED>; + power-source = <PM8994_GPIO_S4>; + }; + + pm8994-gpio19-nc { + pins = "gpio19"; + function = PMIC_GPIO_FUNC_NORMAL; + output-low; + drive-push-pull; + bias-high-impedance; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; + power-source = <PM8994_GPIO_VPH>; + }; + + pm8994-gpio22-nc { + pins = "gpio22"; + function = PMIC_GPIO_FUNC_NORMAL; + drive-push-pull; + bias-high-impedance; + power-source = <PM8994_GPIO_VPH>; + }; + }; +}; + +&pm8994_mpps { + pinctrl-names = "default"; + pinctrl-0 = <&pm8994_mpps_defaults>; + + gpio-line-names = + "SDC_UIM_VBIAS", + "LCD_ID_ADC", + "VREF_DACX", + "NC", + "FLASH_THERM", + "NC", + "NC", + "RF_ID"; + + pm8994_mpps_defaults: pm8994-mpps-default-state { + lcd-id_adc-mpp { + pins = "mpp2"; + function = "analog"; + input-enable; + qcom,amux-route = <PMIC_MPP_AMUX_ROUTE_CH6>; + }; + + pm-mpp4-nc { + pins = "mpp4"; + function = "digital"; + bias-high-impedance; + power-source = <PM8994_GPIO_VPH>; + }; + + flash-therm-mpp { + pins = "mpp5"; + function = "analog"; + input-enable; + qcom,amux-route = <PMIC_MPP_AMUX_ROUTE_CH5>; + }; + + mpp6-nc { + pins = "mpp6"; + function = "digital"; + bias-high-impedance; + }; + + rf-id-mpp { + pins = "mpp8"; + function = "analog"; + input-enable; + qcom,amux-route = <PMIC_MPP_AMUX_ROUTE_CH8>; + }; + }; +}; + +&pm8994_resin { + status = "okay"; + linux,code = <KEY_VOLUMEUP>; +}; + +&pmi8994_gpios { + pinctrl-names = "default"; + pinctrl-0 = <&pmi8994_gpios_defaults>; + + gpio-line-names = + "VIB_LDO_EN", + "NC", + "NC", + "NC", + "NC", + "NC", + "NC", + "NC", + "USB_SWITCH_SEL", + "NC"; + + pmi8994_gpios_defaults: pmi8994-gpios-default-state { + vib-ldo-en-gpio { + pins = "gpio1"; + function = PMIC_GPIO_FUNC_NORMAL; + drive-push-pull; + output-low; + bias-disable; + power-source = <PM8994_GPIO_S4>; + }; + + pmi-gpio2-nc { + pins = "gpio2"; + function = PMIC_GPIO_FUNC_NORMAL; + drive-push-pull; + input-enable; + bias-high-impedance; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; + power-source = <PM8994_GPIO_VPH>; + }; + + pmi-gpio3-nc { + pins = "gpio3"; + function = PMIC_GPIO_FUNC_NORMAL; + drive-push-pull; + input-enable; + bias-high-impedance; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; + power-source = <PM8994_GPIO_VPH>; + }; + + pmi-gpio4-nc { + pins = "gpio4"; + function = PMIC_GPIO_FUNC_NORMAL; + drive-push-pull; + output-high; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; + power-source = <PM8994_GPIO_S4>; + }; + + pmi-gpio5-nc { + pins = "gpio5"; + function = PMIC_GPIO_FUNC_NORMAL; + drive-push-pull; + output-high; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; + power-source = <PM8994_GPIO_S4>; + }; + + pmi-gpio6-nc { + pins = "gpio6"; + function = PMIC_GPIO_FUNC_NORMAL; + drive-push-pull; + output-high; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; + power-source = <PM8994_GPIO_S4>; + }; + + pmi-gpio7-nc { + pins = "gpio7"; + function = PMIC_GPIO_FUNC_NORMAL; + drive-push-pull; + output-high; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; + power-source = <PM8994_GPIO_S4>; + }; + + pmi-gpio8-nc { + pins = "gpio8"; + function = PMIC_GPIO_FUNC_NORMAL; + drive-push-pull; + output-high; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; + power-source = <PM8994_GPIO_S4>; + }; + + usb-switch-sel { + pins = "gpio9"; + function = PMIC_GPIO_FUNC_NORMAL; + drive-push-pull; + }; + + pmi-gpio10-nc { + pins = "gpio10"; + function = PMIC_GPIO_FUNC_NORMAL; + output-low; + drive-push-pull; + bias-disable; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; + power-source = <PM8994_GPIO_S4>; + }; + }; +}; + +&pmi8994_spmi_regulators { + qcom,saw-reg = <&saw3>; + + vdd_gfx: + pmi8994_s2: s2 { + /* Pinned to a high value for now to avoid random crashes. */ + regulator-min-microvolt = <1015000>; + regulator-max-microvolt = <1015000>; + regulator-name = "vdd_gfx"; + regulator-always-on; + }; + + pmi8994_s9: s9 { + qcom,saw-slave; + }; + + pmi8994_s10: s10 { + qcom,saw-slave; + }; + + pmi8994_s11: s11 { + qcom,saw-leader; + regulator-always-on; + regulator-min-microvolt = <470000>; + regulator-max-microvolt = <1140000>; + }; +}; + +&pmi8994_wled { + status = "okay"; + default-brightness = <512>; +}; + +&rpm_requests { + pm8994-regulators { + compatible = "qcom,rpm-pm8994-regulators"; + + vdd_s1-supply = <&vph_pwr>; + vdd_s2-supply = <&vph_pwr>; + vdd_s3-supply = <&vph_pwr>; + vdd_s4-supply = <&vph_pwr>; + vdd_s5-supply = <&vph_pwr>; + vdd_s6-supply = <&vph_pwr>; + vdd_s7-supply = <&vph_pwr>; + vdd_s8-supply = <&vph_pwr>; + vdd_s9-supply = <&vph_pwr>; + vdd_s10-supply = <&vph_pwr>; + vdd_s11-supply = <&vph_pwr>; + vdd_s12-supply = <&vph_pwr>; + vdd_l1-supply = <&pm8994_s3>; + vdd_l2_l26_l28-supply = <&pm8994_s3>; + vdd_l3_l11-supply = <&pm8994_s3>; + vdd_l4_l27_l31-supply = <&pm8994_s3>; + vdd_l5_l7-supply = <&pm8994_s5>; + vdd_l6_l12_l32-supply = <&pm8994_s5>; + vdd_l8_l16_l30-supply = <&vph_pwr>; + vdd_l14_l15-supply = <&pm8994_s5>; + vdd_l20_l21-supply = <&pm8994_s5>; + vdd_l25-supply = <&pm8994_s3>; + vdd_lvs1_2-supply = <&pm8994_s4>; + + pm8994_s3: s3 { + regulator-min-microvolt = <1300000>; + regulator-max-microvolt = <1300000>; + }; + + pm8994_s4: s4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-system-load = <325000>; + regulator-always-on; + }; + + pm8994_s5: s5 { + regulator-min-microvolt = <2150000>; + regulator-max-microvolt = <2150000>; + }; + + pm8994_s7: s7 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + }; + + pm8994_l1: l1 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + pm8994_l2: l2 { + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + }; + + pm8994_l3: l3 { + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + }; + + pm8994_l4: l4 { + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1225000>; + }; + + /* L6 and L7 seem unused. */ + + pm8994_l8: l8 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + pm8994_l9: l9 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + pm8994_l10: l10 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + pm8994_l11: l11 { + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + }; + + pm8994_l12: l12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-allow-set-load; + }; + + pm8994_l13: l13 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + regulator-system-load = <22000>; + regulator-allow-set-load; + }; + + pm8994_l14: l14 { + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <1900000>; + }; + + pm8994_l15: l15 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + pm8994_l16: l16 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + }; + + pm8994_l17: l17 { + regulator-min-microvolt = <2200000>; + regulator-max-microvolt = <2500000>; + }; + + pm8994_l18: l18 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + pm8994_l19: l19 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + + pm8994_l20: l20 { + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <2950000>; + regulator-system-load = <570000>; + regulator-allow-set-load; + }; + + pm8994_l21: l21 { + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <2950000>; + regulator-system-load = <800000>; + regulator-allow-set-load; + }; + + pm8994_l22: l22 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + + pm8994_l23: l23 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + }; + + pm8994_l24: l24 { + regulator-min-microvolt = <3075000>; + regulator-max-microvolt = <3075000>; + regulator-allow-set-load; + }; + + pm8994_l25: l25 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-allow-set-load; + }; + + pm8994_l27: l27 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1200000>; + }; + + pm8994_l28: l28 { + regulator-min-microvolt = <925000>; + regulator-max-microvolt = <925000>; + regulator-allow-set-load; + }; + + pm8994_l29: l29 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + }; + + pm8994_l30: l30 { }; + + pm8994_l32: l32 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + }; +}; + +&sdhc1 { + /* eMMC doesn't seem to cooperate even in PIO mode.. */ + status = "disabled"; + + vmmc-supply = <&pm8994_l20>; + vqmmc-supply = <&pm8994_s4>; + mmc-hs400-1_8v; + mmc-hs200-1_8v; +}; + +&sdhc2 { + status = "okay"; + + cd-gpios = <&tlmm 40 GPIO_ACTIVE_HIGH>; + vmmc-supply = <&pm8994_l21>; + vqmmc-supply = <&pm8994_l13>; +}; + +&tlmm { + gpio-reserved-ranges = <0 4>; + pinctrl-0 = <&sw_service_gpio>; + pinctrl-names = "default"; + + disp_reset_n_gpio: disp-reset-n { + pins = "gpio8"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + mdp_vsync_p_gpio: mdp-vsync-p { + pins = "gpio10"; + function = "mdp_vsync"; + drive-strength = <2>; + bias-disable; + }; + + sw_service_gpio: sw-service-gpio { + pins = "gpio16"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + + usb_detect: usb-detect { + pins = "gpio25"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + output-high; + }; + + uim_detect_en: uim-detect-en { + pins = "gpio29"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + output-high; + }; + + tray_det_pin: tray-det { + pins = "gpio40"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + tp_vddio_en: tp-vddio-en { + pins = "gpio50"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + output-high; + }; + + lcd_vddio_en: lcd-vddio-en { + pins = "gpio51"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + output-low; + }; + + wl_host_wake: wl-host-wake { + pins = "gpio79"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + input-high; + }; + + wl_reg_on: wl-reg-on { + pins = "gpio84"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + output-low; + }; + + ts_reset_n: ts-rst-n { + pins = "gpio89"; + function = "gpio"; + drive-strength = <2>; + }; + + touch_int_n: touch-int-n { + pins = "gpio125"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + + touch_int_sleep: touch-int-sleep { + pins = "gpio125"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + }; +}; + +/* + * For reasons that are currently unknown (but probably related to fusb301), USB takes about + * 6 minutes to wake up (nothing interesting in kernel logs), but then it works as it should. + */ +&usb3 { + status = "okay"; + qcom,select-utmi-as-pipe-clk; +}; + +&usb3_dwc3 { + extcon = <&usb3_id>; + dr_mode = "peripheral"; + phys = <&hsusb_phy1>; + phy-names = "usb2-phy"; + snps,hird-threshold = /bits/ 8 <0>; +}; diff --git a/dts/src/arm64/qcom/msm8996-v3.0.dtsi b/dts/src/arm64/qcom/msm8996-v3.0.dtsi new file mode 100644 index 0000000000..5728583af4 --- /dev/null +++ b/dts/src/arm64/qcom/msm8996-v3.0.dtsi @@ -0,0 +1,63 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org> + */ + +#include "msm8996.dtsi" + +/ { + qcom,msm-id = <246 0x30000>; +}; + + /* + * This revision seems to have differ GPU CPR + * parameters, GPU frequencies and some differences + * when it comes to voltage delivery to.. once again + * the GPU. Funnily enough, it's simpler to make it an + * overlay on top of 3.1 (the final one) than vice versa. + * The differences will show here as more and more + * features get enabled upstream. + */ + +gpu_opp_table_3_0: gpu-opp-table-30 { + compatible = "operating-points-v2"; + + opp-624000000 { + opp-hz = /bits/ 64 <624000000>; + opp-level = <7>; + }; + + opp-560000000 { + opp-hz = /bits/ 64 <560000000>; + opp-level = <6>; + }; + + opp-510000000 { + opp-hz = /bits/ 64 <510000000>; + opp-level = <5>; + }; + + opp-401800000 { + opp-hz = /bits/ 64 <401800000>; + opp-level = <4>; + }; + + opp-315000000 { + opp-hz = /bits/ 64 <315000000>; + opp-level = <3>; + }; + + opp-214000000 { + opp-hz = /bits/ 64 <214000000>; + opp-level = <3>; + }; + + opp-133000000 { + opp-hz = /bits/ 64 <133000000>; + opp-level = <3>; + }; +}; + +&gpu { + operating-points-v2 = <&gpu_opp_table_3_0>; +}; diff --git a/dts/src/arm64/qcom/msm8996.dtsi b/dts/src/arm64/qcom/msm8996.dtsi index 78c55ca10b..52df22ab3f 100644 --- a/dts/src/arm64/qcom/msm8996.dtsi +++ b/dts/src/arm64/qcom/msm8996.dtsi @@ -19,14 +19,14 @@ chosen { }; clocks { - xo_board: xo_board { + xo_board: xo-board { compatible = "fixed-clock"; #clock-cells = <0>; clock-frequency = <19200000>; clock-output-names = "xo_board"; }; - sleep_clk: sleep_clk { + sleep_clk: sleep-clk { compatible = "fixed-clock"; #clock-cells = <0>; clock-frequency = <32764>; @@ -368,10 +368,10 @@ #hwlock-cells = <1>; }; - memory { + memory@80000000 { device_type = "memory"; /* We expect the bootloader to fill in the reg */ - reg = <0 0 0 0>; + reg = <0x0 0x80000000 0x0 0x0>; }; psci { @@ -898,6 +898,8 @@ phy-names = "hdmi_phy"; #sound-dai-cells = <1>; + status = "disabled"; + ports { #address-cells = <1>; #size-cells = <0>; @@ -931,6 +933,8 @@ <&gcc GCC_HDMI_CLKREF_CLK>; clock-names = "iface", "ref"; + + status = "disabled"; }; }; @@ -968,6 +972,8 @@ status = "disabled"; + #cooling-cells = <2>; + gpu_opp_table: opp-table { compatible ="operating-points-v2"; @@ -1082,21 +1088,21 @@ camera0_state_on: camera_rear_default: camera-rear-default { - mclk0 { + camera0_mclk: mclk0 { pins = "gpio13"; function = "cam_mclk"; drive-strength = <16>; bias-disable; }; - rst { + camera0_rst: rst { pins = "gpio25"; function = "gpio"; drive-strength = <16>; bias-disable; }; - pwdn { + camera0_pwdn: pwdn { pins = "gpio26"; function = "gpio"; drive-strength = <16>; @@ -1137,14 +1143,14 @@ camera2_state_on: camera_front_default: camera-front-default { - mclk2 { + camera2_mclk: mclk2 { pins = "gpio15"; function = "cam_mclk"; drive-strength = <16>; bias-disable; }; - rst { + camera2_rst: rst { pins = "gpio23"; function = "gpio"; drive-strength = <16>; @@ -2566,7 +2572,7 @@ power-domains = <&gcc USB30_GDSC>; status = "disabled"; - dwc3@6a00000 { + usb3_dwc3: dwc3@6a00000 { compatible = "snps,dwc3"; reg = <0x06a00000 0xcc00>; interrupts = <0 131 IRQ_TYPE_LEVEL_HIGH>; @@ -3205,7 +3211,14 @@ gpu1_alert0: trip-point0 { temperature = <90000>; hysteresis = <2000>; - type = "hot"; + type = "passive"; + }; + }; + + cooling-maps { + map0 { + trip = <&gpu1_alert0>; + cooling-device = <&gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; }; }; }; @@ -3220,7 +3233,14 @@ gpu2_alert0: trip-point0 { temperature = <90000>; hysteresis = <2000>; - type = "hot"; + type = "passive"; + }; + }; + + cooling-maps { + map0 { + trip = <&gpu2_alert0>; + cooling-device = <&gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; }; }; }; diff --git a/dts/src/arm64/qcom/msm8998.dtsi b/dts/src/arm64/qcom/msm8998.dtsi index e9d3ce2993..34039b5c80 100644 --- a/dts/src/arm64/qcom/msm8998.dtsi +++ b/dts/src/arm64/qcom/msm8998.dtsi @@ -18,10 +18,10 @@ chosen { }; - memory { + memory@80000000 { device_type = "memory"; /* We expect the bootloader to fill in the reg */ - reg = <0 0 0 0>; + reg = <0x0 0x80000000 0x0 0x0>; }; reserved-memory { diff --git a/dts/src/arm64/qcom/pm660.dtsi b/dts/src/arm64/qcom/pm660.dtsi index 2e6a6f6c3b..e847d7209a 100644 --- a/dts/src/arm64/qcom/pm660.dtsi +++ b/dts/src/arm64/qcom/pm660.dtsi @@ -3,9 +3,35 @@ * Copyright (c) 2020, Konrad Dybcio */ +#include <dt-bindings/iio/qcom,spmi-vadc.h> #include <dt-bindings/input/linux-event-codes.h> #include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/spmi/spmi.h> +#include <dt-bindings/thermal/thermal.h> + +/ { + thermal-zones { + pm660 { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&pm660_temp>; + + trips { + pm660_alert0: pm660-alert0 { + temperature = <95000>; + hysteresis = <2000>; + type = "passive"; + }; + pm660_crit: pm660-crit { + temperature = <125000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + }; +}; &spmi_bus { @@ -37,6 +63,102 @@ }; + pm660_temp: temp-alarm@2400 { + compatible = "qcom,spmi-temp-alarm"; + reg = <0x2400>; + interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>; + io-channels = <&pm660_adc ADC5_DIE_TEMP>; + io-channel-names = "thermal"; + #thermal-sensor-cells = <0>; + }; + + pm660_adc: adc@3100 { + compatible = "qcom,spmi-adc-rev2"; + reg = <0x3100>; + interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; + #address-cells = <1>; + #size-cells = <0>; + #io-channel-cells = <1>; + + ref_gnd: ref_gnd@0 { + reg = <ADC5_REF_GND>; + qcom,decimation = <1024>; + qcom,pre-scaling = <1 1>; + }; + + vref_1p25: vref_1p25@1 { + reg = <ADC5_1P25VREF>; + qcom,decimation = <1024>; + qcom,pre-scaling = <1 1>; + }; + + die_temp: die_temp@6 { + reg = <ADC5_DIE_TEMP>; + qcom,decimation = <1024>; + qcom,pre-scaling = <1 1>; + }; + + xo_therm: xo_therm@4c { + reg = <ADC5_XO_THERM_100K_PU>; + qcom,pre-scaling = <1 1>; + qcom,decimation = <1024>; + qcom,hw-settle-time = <200>; + qcom,ratiometric; + }; + + msm_therm: msm_therm@4d { + reg = <ADC5_AMUX_THM1_100K_PU>; + qcom,pre-scaling = <1 1>; + qcom,decimation = <1024>; + qcom,hw-settle-time = <200>; + qcom,ratiometric; + }; + + emmc_therm: emmc_therm@4e { + reg = <ADC5_AMUX_THM2_100K_PU>; + qcom,pre-scaling = <1 1>; + qcom,decimation = <1024>; + qcom,hw-settle-time = <200>; + qcom,ratiometric; + }; + + pa_therm0: thermistor0@4f { + reg = <ADC5_AMUX_THM3_100K_PU>; + qcom,pre-scaling = <1 1>; + qcom,decimation = <1024>; + qcom,hw-settle-time = <200>; + qcom,ratiometric; + }; + + pa_therm1: thermistor1@50 { + reg = <ADC5_AMUX_THM4_100K_PU>; + qcom,pre-scaling = <1 1>; + qcom,decimation = <1024>; + qcom,hw-settle-time = <200>; + qcom,ratiometric; + }; + + quiet_therm: quiet_therm@51 { + reg = <ADC5_AMUX_THM5_100K_PU>; + qcom,pre-scaling = <1 1>; + qcom,decimation = <1024>; + qcom,hw-settle-time = <200>; + qcom,ratiometric; + }; + + vadc_vph_pwr: vph_pwr@83 { + reg = <ADC5_VPH_PWR>; + qcom,decimation = <1024>; + qcom,pre-scaling = <1 3>; + }; + + vcoin: vcoin@83 { + reg = <ADC5_VCOIN>; + qcom,decimation = <1024>; + qcom,pre-scaling = <1 3>; + }; + }; + pm660_gpios: gpios@c000 { compatible = "qcom,pm660-gpio"; reg = <0xc000>; @@ -47,4 +169,15 @@ #interrupt-cells = <2>; }; }; + + pmic@1 { + compatible = "qcom,pm660", "qcom,spmi-pmic"; + reg = <0x1 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pm660_spmi_regulators: pm660-regulators { + compatible = "qcom,pm660-regulators"; + }; + }; }; diff --git a/dts/src/arm64/qcom/pm660l.dtsi b/dts/src/arm64/qcom/pm660l.dtsi index edba6de020..05086cbe57 100644 --- a/dts/src/arm64/qcom/pm660l.dtsi +++ b/dts/src/arm64/qcom/pm660l.dtsi @@ -3,9 +3,35 @@ * Copyright (c) 2020, Konrad Dybcio */ +#include <dt-bindings/iio/qcom,spmi-vadc.h> #include <dt-bindings/input/linux-event-codes.h> #include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/spmi/spmi.h> +#include <dt-bindings/thermal/thermal.h> + +/ { + thermal-zones { + pm660l { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&pm660l_temp>; + + trips { + pm660l_alert0: pm660l-alert0 { + temperature = <95000>; + hysteresis = <2000>; + type = "passive"; + }; + pm660l_crit: pm660l-crit { + temperature = <125000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + }; +}; &spmi_bus { @@ -15,6 +41,13 @@ #address-cells = <1>; #size-cells = <0>; + pm660l_temp: temp-alarm@2400 { + compatible = "qcom,spmi-temp-alarm"; + reg = <0x2400>; + interrupts = <0x2 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; + #thermal-sensor-cells = <0>; + }; + pm660l_gpios: gpios@c000 { compatible = "qcom,pm660l-gpio", "qcom,spmi-gpio"; reg = <0xc000>; @@ -31,6 +64,27 @@ reg = <0x3 SPMI_USID>; #address-cells = <1>; #size-cells = <0>; + + pm660l_wled: leds@d800 { + compatible = "qcom,pm660l-wled"; + reg = <0xd800 0xd900>; + interrupts = <0x3 0xd8 0x1 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "ovp"; + label = "backlight"; + + qcom,switching-freq = <800>; + qcom,ovp-millivolt = <29600>; + qcom,current-boost-limit = <970>; + qcom,current-limit-microamp = <20000>; + qcom,num-strings = <2>; + qcom,enabled-strings = <0 1>; + + status = "disabled"; + }; + + pm660l_spmi_regulators: pm660l-regulators { + compatible = "qcom,pm660l-regulators"; + }; }; }; diff --git a/dts/src/arm64/qcom/pm8004.dtsi b/dts/src/arm64/qcom/pm8004.dtsi index 0abd1abe12..532b79acf0 100644 --- a/dts/src/arm64/qcom/pm8004.dtsi +++ b/dts/src/arm64/qcom/pm8004.dtsi @@ -9,7 +9,6 @@ reg = <0x4 SPMI_USID>; #address-cells = <1>; #size-cells = <0>; - status = "disabled"; }; pm8004_lsid5: pmic@5 { @@ -17,7 +16,6 @@ reg = <0x5 SPMI_USID>; #address-cells = <1>; #size-cells = <0>; - status = "disabled"; pm8004_spmi_regulators: regulators { compatible = "qcom,pm8004-regulators"; diff --git a/dts/src/arm64/qcom/pm8150b.dtsi b/dts/src/arm64/qcom/pm8150b.dtsi index b21e56a461..058cc5107c 100644 --- a/dts/src/arm64/qcom/pm8150b.dtsi +++ b/dts/src/arm64/qcom/pm8150b.dtsi @@ -53,6 +53,12 @@ status = "disabled"; }; + pm8150b_vbus: dcdc@1100 { + compatible = "qcom,pm8150b-vbus-reg"; + status = "disabled"; + reg = <0x1100>; + }; + pm8150b_temp: temp-alarm@2400 { compatible = "qcom,spmi-temp-alarm"; reg = <0x2400>; diff --git a/dts/src/arm64/qcom/pmi8996.dtsi b/dts/src/arm64/qcom/pmi8996.dtsi new file mode 100644 index 0000000000..31b47209e2 --- /dev/null +++ b/dts/src/arm64/qcom/pmi8996.dtsi @@ -0,0 +1,15 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org> + */ + + /* + * PMI8996 is a slight modification of PMI8994 with + * some notable changes, like being the first PMIC + * whose the bootloader has to check to continue booting + * and a change to a LABIBB parameter. + */ + +/ { + qcom,pmic-id = <0x20009 0x10013 0 0>; +}; diff --git a/dts/src/arm64/qcom/sa8155p-adp.dts b/dts/src/arm64/qcom/sa8155p-adp.dts index 0da7a3b8d1..5ae2ddc65f 100644 --- a/dts/src/arm64/qcom/sa8155p-adp.dts +++ b/dts/src/arm64/qcom/sa8155p-adp.dts @@ -307,10 +307,6 @@ status = "okay"; }; -&tlmm { - gpio-reserved-ranges = <0 4>; -}; - &uart2 { status = "okay"; }; @@ -337,6 +333,16 @@ vdda-pll-max-microamp = <18300>; }; +&usb_1 { + status = "okay"; +}; + +&usb_1_dwc3 { + dr_mode = "host"; + + pinctrl-names = "default"; + pinctrl-0 = <&usb2phy_ac_en1_default>; +}; &usb_1_hsphy { status = "okay"; @@ -346,15 +352,51 @@ }; &usb_1_qmpphy { + status = "disabled"; +}; + +&usb_2 { status = "okay"; - vdda-phy-supply = <&vreg_l8c_1p2>; - vdda-pll-supply = <&vdda_usb_ss_dp_core_1>; }; -&usb_1 { +&usb_2_dwc3 { + dr_mode = "host"; + + pinctrl-names = "default"; + pinctrl-0 = <&usb2phy_ac_en2_default>; +}; + +&usb_2_hsphy { status = "okay"; + vdda-pll-supply = <&vdd_usb_hs_core>; + vdda33-supply = <&vdda_usb_hs_3p1>; + vdda18-supply = <&vdda_usb_hs_1p8>; }; -&usb_1_dwc3 { - dr_mode = "peripheral"; +&usb_2_qmpphy { + status = "okay"; + vdda-phy-supply = <&vreg_l8c_1p2>; + vdda-pll-supply = <&vdda_usb_ss_dp_core_1>; +}; + +&tlmm { + gpio-reserved-ranges = <0 4>; + + usb2phy_ac_en1_default: usb2phy_ac_en1_default { + mux { + pins = "gpio113"; + function = "usb2phy_ac"; + bias-disable; + drive-strength = <2>; + }; + }; + + usb2phy_ac_en2_default: usb2phy_ac_en2_default { + mux { + pins = "gpio123"; + function = "usb2phy_ac"; + bias-disable; + drive-strength = <2>; + }; + }; }; diff --git a/dts/src/arm64/qcom/sc7180-trogdor-coachz.dtsi b/dts/src/arm64/qcom/sc7180-trogdor-coachz.dtsi index 6f9c071475..a758e4d226 100644 --- a/dts/src/arm64/qcom/sc7180-trogdor-coachz.dtsi +++ b/dts/src/arm64/qcom/sc7180-trogdor-coachz.dtsi @@ -23,7 +23,7 @@ ap_h1_spi: &spi0 {}; adau7002: audio-codec-1 { compatible = "adi,adau7002"; IOVDD-supply = <&pp1800_l15a>; - wakeup-delay-ms = <15>; + wakeup-delay-ms = <80>; #sound-dai-cells = <0>; }; diff --git a/dts/src/arm64/qcom/sc7180-trogdor.dtsi b/dts/src/arm64/qcom/sc7180-trogdor.dtsi index 77ae7561d4..0f2b3c00e4 100644 --- a/dts/src/arm64/qcom/sc7180-trogdor.dtsi +++ b/dts/src/arm64/qcom/sc7180-trogdor.dtsi @@ -247,29 +247,14 @@ }; }; - max98357a: audio-codec-0 { - compatible = "maxim,max98357a"; + max98360a: audio-codec-0 { + compatible = "maxim,max98360a"; pinctrl-names = "default"; pinctrl-0 = <&_en>; sdmode-gpios = <&tlmm 23 GPIO_ACTIVE_HIGH>; #sound-dai-cells = <0>; }; - panel: panel { - /* Compatible will be filled in per-board */ - power-supply = <&pp3300_dx_edp>; - backlight = <&backlight>; - hpd-gpios = <&sn65dsi86_bridge 2 GPIO_ACTIVE_HIGH>; - - ports { - port { - panel_in_edp: endpoint { - remote-endpoint = <&sn65dsi86_out>; - }; - }; - }; - }; - pwmleds { compatible = "pwm-leds"; keyboard_backlight: keyboard-backlight { @@ -288,6 +273,7 @@ "Headphone Jack", "HPOL", "Headphone Jack", "HPOR"; + #sound-dai-cells = <0>; #address-cells = <1>; #size-cells = <0>; @@ -311,7 +297,19 @@ }; sound_multimedia1_codec: codec { - sound-dai = <&max98357a>; + sound-dai = <&max98360a>; + }; + }; + + dai-link@2 { + link-name = "MultiMedia2"; + reg = <2>; + cpu { + sound-dai = <&lpass_cpu 2>; + }; + + codec { + sound-dai = <&mdss_dp>; }; }; }; @@ -666,6 +664,21 @@ edp_brij_i2c: &i2c2 { }; }; }; + + aux-bus { + panel: panel { + /* Compatible will be filled in per-board */ + power-supply = <&pp3300_dx_edp>; + backlight = <&backlight>; + hpd-gpios = <&sn65dsi86_bridge 2 GPIO_ACTIVE_HIGH>; + + port { + panel_in_edp: endpoint { + remote-endpoint = <&sn65dsi86_out>; + }; + }; + }; + }; }; }; @@ -768,6 +781,10 @@ hp_i2c: &i2c9 { reg = <MI2S_SECONDARY>; qcom,playback-sd-lines = <0>; }; + + hdmi-primary@0 { + reg = <LPASS_DP_RX>; + }; }; &mdp { @@ -778,6 +795,15 @@ hp_i2c: &i2c9 { status = "okay"; }; +&mdss_dp { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&dp_hot_plug_det>; + data-lanes = <0 1>; + vdda-1p2-supply = <&vdda_usb_ss_dp_1p2>; + vdda-0p9-supply = <&vdda_usb_ss_dp_core>; +}; + &pm6150_adc { charger-thermistor@4f { reg = <ADC5_AMUX_THM3_100K_PU>; diff --git a/dts/src/arm64/qcom/sc7180.dtsi b/dts/src/arm64/qcom/sc7180.dtsi index a9a052f8c6..c8921e2d64 100644 --- a/dts/src/arm64/qcom/sc7180.dtsi +++ b/dts/src/arm64/qcom/sc7180.dtsi @@ -110,6 +110,11 @@ no-map; }; + ipa_fw_mem: memory@8b700000 { + reg = <0 0x8b700000 0 0x10000>; + no-map; + }; + rmtfs_mem: memory@94600000 { compatible = "qcom,rmtfs-mem"; reg = <0x0 0x94600000 0x0 0x200000>; @@ -668,7 +673,7 @@ qfprom: efuse@784000 { compatible = "qcom,sc7180-qfprom", "qcom,qfprom"; - reg = <0 0x00784000 0 0x8ff>, + reg = <0 0x00784000 0 0x7a0>, <0 0x00780000 0 0x7a0>, <0 0x00782000 0 0x100>, <0 0x00786000 0 0x1fff>; @@ -786,6 +791,8 @@ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; + power-domains = <&rpmhpd SC7180_CX>; + required-opps = <&rpmhpd_opp_low_svs>; status = "disabled"; }; @@ -838,6 +845,8 @@ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; + power-domains = <&rpmhpd SC7180_CX>; + required-opps = <&rpmhpd_opp_low_svs>; status = "disabled"; }; @@ -890,6 +899,8 @@ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; + power-domains = <&rpmhpd SC7180_CX>; + required-opps = <&rpmhpd_opp_low_svs>; status = "disabled"; }; @@ -924,6 +935,8 @@ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; + power-domains = <&rpmhpd SC7180_CX>; + required-opps = <&rpmhpd_opp_low_svs>; status = "disabled"; }; @@ -976,6 +989,8 @@ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; + power-domains = <&rpmhpd SC7180_CX>; + required-opps = <&rpmhpd_opp_low_svs>; status = "disabled"; }; @@ -1010,6 +1025,8 @@ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; + power-domains = <&rpmhpd SC7180_CX>; + required-opps = <&rpmhpd_opp_low_svs>; status = "disabled"; }; @@ -1075,6 +1092,8 @@ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; + power-domains = <&rpmhpd SC7180_CX>; + required-opps = <&rpmhpd_opp_low_svs>; status = "disabled"; }; @@ -1127,6 +1146,8 @@ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; + power-domains = <&rpmhpd SC7180_CX>; + required-opps = <&rpmhpd_opp_low_svs>; status = "disabled"; }; @@ -1161,6 +1182,8 @@ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; + power-domains = <&rpmhpd SC7180_CX>; + required-opps = <&rpmhpd_opp_low_svs>; status = "disabled"; }; @@ -1213,6 +1236,8 @@ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; + power-domains = <&rpmhpd SC7180_CX>; + required-opps = <&rpmhpd_opp_low_svs>; status = "disabled"; }; @@ -1247,6 +1272,8 @@ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; + power-domains = <&rpmhpd SC7180_CX>; + required-opps = <&rpmhpd_opp_low_svs>; status = "disabled"; }; @@ -1299,6 +1326,8 @@ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>; interconnect-names = "qup-core", "qup-config", "qup-memory"; + power-domains = <&rpmhpd SC7180_CX>; + required-opps = <&rpmhpd_opp_low_svs>; status = "disabled"; }; @@ -2928,6 +2957,13 @@ remote-endpoint = <&dsi0_in>; }; }; + + port@2 { + reg = <2>; + dpu_intf0_out: endpoint { + remote-endpoint = <&dp_in>; + }; + }; }; mdp_opp_table: mdp-opp-table { @@ -2977,6 +3013,9 @@ "iface", "bus"; + assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>; + assigned-clock-parents = <&dsi_phy 0>, <&dsi_phy 1>; + operating-points-v2 = <&dsi_opp_table>; power-domains = <&rpmhpd SC7180_CX>; @@ -3044,6 +3083,75 @@ status = "disabled"; }; + + mdss_dp: displayport-controller@ae90000 { + compatible = "qcom,sc7180-dp"; + status = "disabled"; + + reg = <0 0x0ae90000 0 0x1400>; + + interrupt-parent = <&mdss>; + interrupts = <12>; + + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&dispcc DISP_CC_MDSS_DP_AUX_CLK>, + <&dispcc DISP_CC_MDSS_DP_LINK_CLK>, + <&dispcc DISP_CC_MDSS_DP_LINK_INTF_CLK>, + <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK>; + clock-names = "core_iface", "core_aux", "ctrl_link", + "ctrl_link_iface", "stream_pixel"; + #clock-cells = <1>; + assigned-clocks = <&dispcc DISP_CC_MDSS_DP_LINK_CLK_SRC>, + <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK_SRC>; + assigned-clock-parents = <&dp_phy 0>, <&dp_phy 1>; + phys = <&dp_phy>; + phy-names = "dp"; + + operating-points-v2 = <&dp_opp_table>; + power-domains = <&rpmhpd SC7180_CX>; + + #sound-dai-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + dp_in: endpoint { + remote-endpoint = <&dpu_intf0_out>; + }; + }; + + port@1 { + reg = <1>; + dp_out: endpoint { }; + }; + }; + + dp_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-160000000 { + opp-hz = /bits/ 64 <160000000>; + required-opps = <&rpmhpd_opp_low_svs>; + }; + + opp-270000000 { + opp-hz = /bits/ 64 <270000000>; + required-opps = <&rpmhpd_opp_svs>; + }; + + opp-540000000 { + opp-hz = /bits/ 64 <540000000>; + required-opps = <&rpmhpd_opp_svs_l1>; + }; + + opp-810000000 { + opp-hz = /bits/ 64 <810000000>; + required-opps = <&rpmhpd_opp_nom>; + }; + }; + }; }; dispcc: clock-controller@af00000 { @@ -3456,17 +3564,20 @@ #power-domain-cells = <1>; }; - lpass_cpu: lpass@62f00000 { + lpass_cpu: lpass@62d87000 { compatible = "qcom,sc7180-lpass-cpu"; - reg = <0 0x62f00000 0 0x29000>; - reg-names = "lpass-lpaif"; + reg = <0 0x62d87000 0 0x68000>, <0 0x62f00000 0 0x29000>; + reg-names = "lpass-hdmiif", "lpass-lpaif"; iommus = <&apps_smmu 0x1020 0>, - <&apps_smmu 0x1021 0>; + <&apps_smmu 0x1021 0>, + <&apps_smmu 0x1032 0>; power-domains = <&lpass_hm LPASS_CORE_HM_GDSCR>; + status = "disabled"; + clocks = <&gcc GCC_LPASS_CFG_NOC_SWAY_CLK>, <&lpasscc LPASS_AUDIO_CORE_CORE_CLK>, <&lpasscc LPASS_AUDIO_CORE_EXT_MCLK0_CLK>, @@ -3483,8 +3594,9 @@ #address-cells = <1>; #size-cells = <0>; - interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "lpass-irq-lpaif"; + interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "lpass-irq-lpaif", "lpass-irq-hdmi"; }; lpass_hm: clock-controller@63000000 { diff --git a/dts/src/arm64/qcom/sc7280-idp.dts b/dts/src/arm64/qcom/sc7280-idp.dts index 3900cfc095..64fc22aff3 100644 --- a/dts/src/arm64/qcom/sc7280-idp.dts +++ b/dts/src/arm64/qcom/sc7280-idp.dts @@ -8,17 +8,11 @@ /dts-v1/; #include <dt-bindings/iio/qcom,spmi-adc7-pmr735a.h> -#include <dt-bindings/iio/qcom,spmi-adc7-pmr735b.h> -#include <dt-bindings/iio/qcom,spmi-adc7-pm8350.h> -#include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h> -#include "sc7280.dtsi" -#include "pm7325.dtsi" +#include "sc7280-idp.dtsi" #include "pmr735a.dtsi" -#include "pm8350c.dtsi" -#include "pmk8350.dtsi" / { - model = "Qualcomm Technologies, Inc. sc7280 IDP platform"; + model = "Qualcomm Technologies, Inc. sc7280 IDP SKU1 platform"; compatible = "qcom,sc7280-idp", "google,senor", "qcom,sc7280"; aliases { @@ -31,186 +25,6 @@ }; &apps_rsc { - pm7325-regulators { - compatible = "qcom,pm7325-rpmh-regulators"; - qcom,pmic-id = "b"; - - vreg_s1b_1p8: smps1 { - regulator-min-microvolt = <1856000>; - regulator-max-microvolt = <2040000>; - }; - - vreg_s7b_0p9: smps7 { - regulator-min-microvolt = <535000>; - regulator-max-microvolt = <1120000>; - }; - - vreg_s8b_1p2: smps8 { - regulator-min-microvolt = <1256000>; - regulator-max-microvolt = <1500000>; - }; - - vreg_l1b_0p8: ldo1 { - regulator-min-microvolt = <825000>; - regulator-max-microvolt = <925000>; - }; - - vreg_l2b_3p0: ldo2 { - regulator-min-microvolt = <2700000>; - regulator-max-microvolt = <3544000>; - }; - - vreg_l6b_1p2: ldo6 { - regulator-min-microvolt = <1140000>; - regulator-max-microvolt = <1260000>; - }; - - vreg_l7b_2p9: ldo7 { - regulator-min-microvolt = <2960000>; - regulator-max-microvolt = <2960000>; - }; - - vreg_l8b_0p9: ldo8 { - regulator-min-microvolt = <870000>; - regulator-max-microvolt = <970000>; - }; - - vreg_l9b_1p2: ldo9 { - regulator-min-microvolt = <1080000>; - regulator-max-microvolt = <1304000>; - }; - - vreg_l11b_1p7: ldo11 { - regulator-min-microvolt = <1504000>; - regulator-max-microvolt = <2000000>; - }; - - vreg_l12b_0p8: ldo12 { - regulator-min-microvolt = <751000>; - regulator-max-microvolt = <824000>; - }; - - vreg_l13b_0p8: ldo13 { - regulator-min-microvolt = <530000>; - regulator-max-microvolt = <824000>; - }; - - vreg_l14b_1p2: ldo14 { - regulator-min-microvolt = <1080000>; - regulator-max-microvolt = <1304000>; - }; - - vreg_l15b_0p8: ldo15 { - regulator-min-microvolt = <765000>; - regulator-max-microvolt = <1020000>; - }; - - vreg_l16b_1p2: ldo16 { - regulator-min-microvolt = <1100000>; - regulator-max-microvolt = <1300000>; - }; - - vreg_l17b_1p8: ldo17 { - regulator-min-microvolt = <1700000>; - regulator-max-microvolt = <1900000>; - }; - - vreg_l18b_1p8: ldo18 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <2000000>; - }; - - vreg_l19b_1p8: ldo19 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - }; - }; - - pm8350c-regulators { - compatible = "qcom,pm8350c-rpmh-regulators"; - qcom,pmic-id = "c"; - - vreg_s1c_2p2: smps1 { - regulator-min-microvolt = <2190000>; - regulator-max-microvolt = <2210000>; - }; - - vreg_s9c_1p0: smps9 { - regulator-min-microvolt = <1010000>; - regulator-max-microvolt = <1170000>; - }; - - vreg_l1c_1p8: ldo1 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1980000>; - }; - - vreg_l2c_1p8: ldo2 { - regulator-min-microvolt = <1620000>; - regulator-max-microvolt = <1980000>; - }; - - vreg_l3c_3p0: ldo3 { - regulator-min-microvolt = <2800000>; - regulator-max-microvolt = <3540000>; - }; - - vreg_l4c_1p8: ldo4 { - regulator-min-microvolt = <1620000>; - regulator-max-microvolt = <3300000>; - }; - - vreg_l5c_1p8: ldo5 { - regulator-min-microvolt = <1620000>; - regulator-max-microvolt = <3300000>; - }; - - vreg_l6c_2p9: ldo6 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <2950000>; - }; - - vreg_l7c_3p0: ldo7 { - regulator-min-microvolt = <3000000>; - regulator-max-microvolt = <3544000>; - }; - - vreg_l8c_1p8: ldo8 { - regulator-min-microvolt = <1620000>; - regulator-max-microvolt = <2000000>; - }; - - vreg_l9c_2p9: ldo9 { - regulator-min-microvolt = <2960000>; - regulator-max-microvolt = <2960000>; - }; - - vreg_l10c_0p8: ldo10 { - regulator-min-microvolt = <720000>; - regulator-max-microvolt = <1050000>; - }; - - vreg_l11c_2p8: ldo11 { - regulator-min-microvolt = <2800000>; - regulator-max-microvolt = <3544000>; - }; - - vreg_l12c_1p8: ldo12 { - regulator-min-microvolt = <1650000>; - regulator-max-microvolt = <2000000>; - }; - - vreg_l13c_3p0: ldo13 { - regulator-min-microvolt = <2700000>; - regulator-max-microvolt = <3544000>; - }; - - vreg_bob: bob { - regulator-min-microvolt = <3008000>; - regulator-max-microvolt = <3960000>; - }; - }; - pmr735a-regulators { compatible = "qcom,pmr735a-rpmh-regulators"; qcom,pmic-id = "e"; @@ -242,52 +56,15 @@ }; }; -&pmk8350_vadc { - pm8350_die_temp { - reg = <PM8350_ADC7_DIE_TEMP>; - label = "pm8350_die_temp"; - qcom,pre-scaling = <1 1>; - }; - - pmk8350_die_temp { - reg = <PMK8350_ADC7_DIE_TEMP>; - label = "pmk8350_die_temp"; - qcom,pre-scaling = <1 1>; - }; - - pmr735a_die_temp { - reg = <PMR735A_ADC7_DIE_TEMP>; - label = "pmr735a_die_temp"; - qcom,pre-scaling = <1 1>; - }; - - pmr735b_die_temp { - reg = <PMR735B_ADC7_DIE_TEMP>; - label = "pmr735b_die_temp"; - qcom,pre-scaling = <1 1>; - }; -}; - -&qupv3_id_0 { +&ipa { status = "okay"; + modem-init; }; -&uart5 { - status = "okay"; -}; - -/* PINCTRL - additions to nodes defined in sc7280.dtsi */ - -&qup_uart5_default { - tx { - pins = "gpio46"; - drive-strength = <2>; - bias-disable; - }; - - rx { - pins = "gpio47"; - drive-strength = <2>; - bias-pull-up; +&pmk8350_vadc { + pmr735a_die_temp { + reg = <PMR735A_ADC7_DIE_TEMP>; + label = "pmr735a_die_temp"; + qcom,pre-scaling = <1 1>; }; }; diff --git a/dts/src/arm64/qcom/sc7280-idp.dtsi b/dts/src/arm64/qcom/sc7280-idp.dtsi new file mode 100644 index 0000000000..371a2a9dcf --- /dev/null +++ b/dts/src/arm64/qcom/sc7280-idp.dtsi @@ -0,0 +1,341 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * sc7280 IDP board device tree source (common between SKU1 and SKU2) + * + * Copyright (c) 2021, The Linux Foundation. All rights reserved. + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h> +#include "sc7280.dtsi" +#include "pm7325.dtsi" +#include "pm8350c.dtsi" +#include "pmk8350.dtsi" + +&apps_rsc { + pm7325-regulators { + compatible = "qcom,pm7325-rpmh-regulators"; + qcom,pmic-id = "b"; + + vreg_s1b_1p8: smps1 { + regulator-min-microvolt = <1856000>; + regulator-max-microvolt = <2040000>; + }; + + vreg_s7b_0p9: smps7 { + regulator-min-microvolt = <535000>; + regulator-max-microvolt = <1120000>; + }; + + vreg_s8b_1p2: smps8 { + regulator-min-microvolt = <1256000>; + regulator-max-microvolt = <1500000>; + }; + + vreg_l1b_0p8: ldo1 { + regulator-min-microvolt = <825000>; + regulator-max-microvolt = <925000>; + }; + + vreg_l2b_3p0: ldo2 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3544000>; + }; + + vreg_l6b_1p2: ldo6 { + regulator-min-microvolt = <1140000>; + regulator-max-microvolt = <1260000>; + }; + + vreg_l7b_2p9: ldo7 { + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + }; + + vreg_l8b_0p9: ldo8 { + regulator-min-microvolt = <870000>; + regulator-max-microvolt = <970000>; + }; + + vreg_l9b_1p2: ldo9 { + regulator-min-microvolt = <1080000>; + regulator-max-microvolt = <1304000>; + }; + + vreg_l11b_1p7: ldo11 { + regulator-min-microvolt = <1504000>; + regulator-max-microvolt = <2000000>; + }; + + vreg_l12b_0p8: ldo12 { + regulator-min-microvolt = <751000>; + regulator-max-microvolt = <824000>; + }; + + vreg_l13b_0p8: ldo13 { + regulator-min-microvolt = <530000>; + regulator-max-microvolt = <824000>; + }; + + vreg_l14b_1p2: ldo14 { + regulator-min-microvolt = <1080000>; + regulator-max-microvolt = <1304000>; + }; + + vreg_l15b_0p8: ldo15 { + regulator-min-microvolt = <765000>; + regulator-max-microvolt = <1020000>; + }; + + vreg_l16b_1p2: ldo16 { + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1300000>; + }; + + vreg_l17b_1p8: ldo17 { + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <1900000>; + }; + + vreg_l18b_1p8: ldo18 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2000000>; + }; + + vreg_l19b_1p8: ldo19 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + }; + + pm8350c-regulators { + compatible = "qcom,pm8350c-rpmh-regulators"; + qcom,pmic-id = "c"; + + vreg_s1c_2p2: smps1 { + regulator-min-microvolt = <2190000>; + regulator-max-microvolt = <2210000>; + }; + + vreg_s9c_1p0: smps9 { + regulator-min-microvolt = <1010000>; + regulator-max-microvolt = <1170000>; + }; + + vreg_l1c_1p8: ldo1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1980000>; + }; + + vreg_l2c_1p8: ldo2 { + regulator-min-microvolt = <1620000>; + regulator-max-microvolt = <1980000>; + }; + + vreg_l3c_3p0: ldo3 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <3540000>; + }; + + vreg_l4c_1p8: ldo4 { + regulator-min-microvolt = <1620000>; + regulator-max-microvolt = <3300000>; + }; + + vreg_l5c_1p8: ldo5 { + regulator-min-microvolt = <1620000>; + regulator-max-microvolt = <3300000>; + }; + + vreg_l6c_2p9: ldo6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + }; + + vreg_l7c_3p0: ldo7 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3544000>; + }; + + vreg_l8c_1p8: ldo8 { + regulator-min-microvolt = <1620000>; + regulator-max-microvolt = <2000000>; + }; + + vreg_l9c_2p9: ldo9 { + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + }; + + vreg_l10c_0p8: ldo10 { + regulator-min-microvolt = <720000>; + regulator-max-microvolt = <1050000>; + }; + + vreg_l11c_2p8: ldo11 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <3544000>; + }; + + vreg_l12c_1p8: ldo12 { + regulator-min-microvolt = <1650000>; + regulator-max-microvolt = <2000000>; + }; + + vreg_l13c_3p0: ldo13 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3544000>; + }; + + vreg_bob: bob { + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3960000>; + }; + }; +}; + +&ipa { + status = "okay"; + modem-init; +}; + +&pmk8350_vadc { + pmk8350_die_temp { + reg = <PMK8350_ADC7_DIE_TEMP>; + label = "pmk8350_die_temp"; + qcom,pre-scaling = <1 1>; + }; +}; + +&qupv3_id_0 { + status = "okay"; +}; + +&sdhc_1 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc1_on>; + pinctrl-1 = <&sdc1_off>; + + non-removable; + no-sd; + no-sdio; + + vmmc-supply = <&vreg_l7b_2p9>; + vqmmc-supply = <&vreg_l19b_1p8>; +}; + +&sdhc_2 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc2_on>; + pinctrl-1 = <&sdc2_off>; + + vmmc-supply = <&vreg_l9c_2p9>; + vqmmc-supply = <&vreg_l6c_2p9>; + + cd-gpios = <&tlmm 91 GPIO_ACTIVE_LOW>; +}; + +&uart5 { + status = "okay"; +}; + +&usb_1 { + status = "okay"; +}; + +&usb_1_dwc3 { + dr_mode = "host"; +}; + +&usb_1_hsphy { + status = "okay"; + + vdda-pll-supply = <&vreg_l10c_0p8>; + vdda33-supply = <&vreg_l2b_3p0>; + vdda18-supply = <&vreg_l1c_1p8>; +}; + +&usb_1_qmpphy { + status = "okay"; + + vdda-phy-supply = <&vreg_l6b_1p2>; + vdda-pll-supply = <&vreg_l1b_0p8>; +}; + +&usb_2 { + status = "okay"; +}; + +&usb_2_dwc3 { + dr_mode = "peripheral"; +}; + +&usb_2_hsphy { + status = "okay"; + + vdda-pll-supply = <&vreg_l10c_0p8>; + vdda33-supply = <&vreg_l2b_3p0>; + vdda18-supply = <&vreg_l1c_1p8>; +}; + +/* PINCTRL - additions to nodes defined in sc7280.dtsi */ + +&qup_uart5_default { + tx { + pins = "gpio46"; + drive-strength = <2>; + bias-disable; + }; + + rx { + pins = "gpio47"; + drive-strength = <2>; + bias-pull-up; + }; +}; + +&sdc1_on { + clk { + bias-disable; + drive-strength = <16>; + }; + + cmd { + bias-pull-up; + drive-strength = <10>; + }; + + data { + bias-pull-up; + drive-strength = <10>; + }; + + rclk { + bias-pull-down; + }; +}; + +&sdc2_on { + clk { + bias-disable; + drive-strength = <16>; + }; + + cmd { + bias-pull-up; + drive-strength = <10>; + }; + + data { + bias-pull-up; + drive-strength = <10>; + }; + + sd-cd { + bias-pull-up; + }; +}; diff --git a/dts/src/arm64/qcom/sc7280-idp2.dts b/dts/src/arm64/qcom/sc7280-idp2.dts new file mode 100644 index 0000000000..1fc2addc8a --- /dev/null +++ b/dts/src/arm64/qcom/sc7280-idp2.dts @@ -0,0 +1,23 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * sc7280 IDP2 board device tree source + * + * Copyright (c) 2021, The Linux Foundation. All rights reserved. + */ + +/dts-v1/; + +#include "sc7280-idp.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. sc7280 IDP SKU2 platform"; + compatible = "qcom,sc7280-idp2", "google,piglin", "qcom,sc7280"; + + aliases { + serial0 = &uart5; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; diff --git a/dts/src/arm64/qcom/sc7280.dtsi b/dts/src/arm64/qcom/sc7280.dtsi index 188c5768a5..53a21d0861 100644 --- a/dts/src/arm64/qcom/sc7280.dtsi +++ b/dts/src/arm64/qcom/sc7280.dtsi @@ -7,6 +7,7 @@ #include <dt-bindings/clock/qcom,gcc-sc7280.h> #include <dt-bindings/clock/qcom,rpmh.h> +#include <dt-bindings/interconnect/qcom,sc7280.h> #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/mailbox/qcom-ipcc.h> #include <dt-bindings/power/qcom-aoss-qmp.h> @@ -24,6 +25,11 @@ chosen { }; + aliases { + mmc1 = &sdhc_1; + mmc2 = &sdhc_2; + }; + clocks { xo_board: xo-board { compatible = "fixed-clock"; @@ -63,6 +69,11 @@ no-map; reg = <0x0 0x80b00000 0x0 0x100000>; }; + + ipa_fw_mem: memory@8b700000 { + reg = <0 0x8b700000 0 0x10000>; + no-map; + }; }; cpus { @@ -436,6 +447,73 @@ #mbox-cells = <2>; }; + qfprom: efuse@784000 { + compatible = "qcom,sc7280-qfprom", "qcom,qfprom"; + reg = <0 0x00784000 0 0xa20>, + <0 0x00780000 0 0xa20>, + <0 0x00782000 0 0x120>, + <0 0x00786000 0 0x1fff>; + clocks = <&gcc GCC_SEC_CTRL_CLK_SRC>; + clock-names = "core"; + power-domains = <&rpmhpd SC7280_MX>; + #address-cells = <1>; + #size-cells = <1>; + }; + + sdhc_1: sdhci@7c4000 { + compatible = "qcom,sc7280-sdhci", "qcom,sdhci-msm-v5"; + status = "disabled"; + + reg = <0 0x007c4000 0 0x1000>, + <0 0x007c5000 0 0x1000>; + reg-names = "hc", "cqhci"; + + iommus = <&apps_smmu 0xc0 0x0>; + interrupts = <GIC_SPI 652 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 656 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hc_irq", "pwr_irq"; + + clocks = <&gcc GCC_SDCC1_APPS_CLK>, + <&gcc GCC_SDCC1_AHB_CLK>, + <&rpmhcc RPMH_CXO_CLK>; + clock-names = "core", "iface", "xo"; + interconnects = <&aggre1_noc MASTER_SDCC_1 0 &mc_virt SLAVE_EBI1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_SDCC_1 0>; + interconnect-names = "sdhc-ddr","cpu-sdhc"; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&sdhc1_opp_table>; + + bus-width = <8>; + supports-cqe; + + qcom,dll-config = <0x0007642c>; + qcom,ddr-config = <0x80040868>; + + mmc-ddr-1_8v; + mmc-hs200-1_8v; + mmc-hs400-1_8v; + mmc-hs400-enhanced-strobe; + + sdhc1_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-100000000 { + opp-hz = /bits/ 64 <100000000>; + required-opps = <&rpmhpd_opp_low_svs>; + opp-peak-kBps = <1800000 400000>; + opp-avg-kBps = <100000 0>; + }; + + opp-384000000 { + opp-hz = /bits/ 64 <384000000>; + required-opps = <&rpmhpd_opp_nom>; + opp-peak-kBps = <5400000 1600000>; + opp-avg-kBps = <390000 0>; + }; + }; + + }; + qupv3_id_0: geniqup@9c0000 { compatible = "qcom,geni-se-qup"; reg = <0 0x009c0000 0 0x2000>; @@ -508,6 +586,43 @@ qcom,bcm-voters = <&apps_bcm_voter>; }; + ipa: ipa@1e40000 { + compatible = "qcom,sc7280-ipa"; + + iommus = <&apps_smmu 0x480 0x0>, + <&apps_smmu 0x482 0x0>; + reg = <0 0x1e40000 0 0x8000>, + <0 0x1e50000 0 0x4ad0>, + <0 0x1e04000 0 0x23000>; + reg-names = "ipa-reg", + "ipa-shared", + "gsi"; + + interrupts-extended = <&intc 0 654 IRQ_TYPE_EDGE_RISING>, + <&intc 0 432 IRQ_TYPE_LEVEL_HIGH>, + <&ipa_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, + <&ipa_smp2p_in 1 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "ipa", + "gsi", + "ipa-clock-query", + "ipa-setup-ready"; + + clocks = <&rpmhcc RPMH_IPA_CLK>; + clock-names = "core"; + + interconnects = <&aggre2_noc MASTER_IPA 0 &mc_virt SLAVE_EBI1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_IPA_CFG 0>; + interconnect-names = "memory", + "config"; + + qcom,smem-states = <&ipa_smp2p_out 0>, + <&ipa_smp2p_out 1>; + qcom,smem-state-names = "ipa-clock-enabled-valid", + "ipa-clock-enabled"; + + status = "disabled"; + }; + tcsr_mutex: hwlock@1f40000 { compatible = "qcom,tcsr-mutex", "syscon"; reg = <0 0x01f40000 0 0x40000>; @@ -1035,6 +1150,174 @@ }; }; + sdhc_2: sdhci@8804000 { + compatible = "qcom,sc7280-sdhci", "qcom,sdhci-msm-v5"; + status = "disabled"; + + reg = <0 0x08804000 0 0x1000>; + + iommus = <&apps_smmu 0x100 0x0>; + interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hc_irq", "pwr_irq"; + + clocks = <&gcc GCC_SDCC2_APPS_CLK>, + <&gcc GCC_SDCC2_AHB_CLK>, + <&rpmhcc RPMH_CXO_CLK>; + clock-names = "core", "iface", "xo"; + interconnects = <&aggre1_noc MASTER_SDCC_2 0 &mc_virt SLAVE_EBI1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_SDCC_2 0>; + interconnect-names = "sdhc-ddr","cpu-sdhc"; + power-domains = <&rpmhpd SC7280_CX>; + operating-points-v2 = <&sdhc2_opp_table>; + + bus-width = <4>; + + qcom,dll-config = <0x0007642c>; + + sdhc2_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-100000000 { + opp-hz = /bits/ 64 <100000000>; + required-opps = <&rpmhpd_opp_low_svs>; + opp-peak-kBps = <1800000 400000>; + opp-avg-kBps = <100000 0>; + }; + + opp-202000000 { + opp-hz = /bits/ 64 <202000000>; + required-opps = <&rpmhpd_opp_nom>; + opp-peak-kBps = <5400000 1600000>; + opp-avg-kBps = <200000 0>; + }; + }; + + }; + + usb_1_hsphy: phy@88e3000 { + compatible = "qcom,sc7280-usb-hs-phy", + "qcom,usb-snps-hs-7nm-phy"; + reg = <0 0x088e3000 0 0x400>; + status = "disabled"; + #phy-cells = <0>; + + clocks = <&rpmhcc RPMH_CXO_CLK>; + clock-names = "ref"; + + resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>; + }; + + usb_2_hsphy: phy@88e4000 { + compatible = "qcom,sc7280-usb-hs-phy", + "qcom,usb-snps-hs-7nm-phy"; + reg = <0 0x088e4000 0 0x400>; + status = "disabled"; + #phy-cells = <0>; + + clocks = <&rpmhcc RPMH_CXO_CLK>; + clock-names = "ref"; + + resets = <&gcc GCC_QUSB2PHY_SEC_BCR>; + }; + + usb_1_qmpphy: phy-wrapper@88e9000 { + compatible = "qcom,sc7280-qmp-usb3-dp-phy", + "qcom,sm8250-qmp-usb3-dp-phy"; + reg = <0 0x088e9000 0 0x200>, + <0 0x088e8000 0 0x40>, + <0 0x088ea000 0 0x200>; + status = "disabled"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>, + <&rpmhcc RPMH_CXO_CLK>, + <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>; + clock-names = "aux", "ref_clk_src", "com_aux"; + + resets = <&gcc GCC_USB3_DP_PHY_PRIM_BCR>, + <&gcc GCC_USB3_PHY_PRIM_BCR>; + reset-names = "phy", "common"; + + usb_1_ssphy: usb3-phy@88e9200 { + reg = <0 0x088e9200 0 0x200>, + <0 0x088e9400 0 0x200>, + <0 0x088e9c00 0 0x400>, + <0 0x088e9600 0 0x200>, + <0 0x088e9800 0 0x200>, + <0 0x088e9a00 0 0x100>; + #clock-cells = <0>; + #phy-cells = <0>; + clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>; + clock-names = "pipe0"; + clock-output-names = "usb3_phy_pipe_clk_src"; + }; + + dp_phy: dp-phy@88ea200 { + reg = <0 0x088ea200 0 0x200>, + <0 0x088ea400 0 0x200>, + <0 0x088eac00 0 0x400>, + <0 0x088ea600 0 0x200>, + <0 0x088ea800 0 0x200>, + <0 0x088eaa00 0 0x100>; + #phy-cells = <0>; + #clock-cells = <1>; + clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>; + clock-names = "pipe0"; + clock-output-names = "usb3_phy_pipe_clk_src"; + }; + }; + + usb_2: usb@8cf8800 { + compatible = "qcom,sc7280-dwc3", "qcom,dwc3"; + reg = <0 0x08cf8800 0 0x400>; + status = "disabled"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + dma-ranges; + + clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>, + <&gcc GCC_USB30_SEC_MASTER_CLK>, + <&gcc GCC_AGGRE_USB3_SEC_AXI_CLK>, + <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>, + <&gcc GCC_USB30_SEC_SLEEP_CLK>; + clock-names = "cfg_noc", "core", "iface","mock_utmi", + "sleep"; + + assigned-clocks = <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>, + <&gcc GCC_USB30_SEC_MASTER_CLK>; + assigned-clock-rates = <19200000>, <200000000>; + + interrupts-extended = <&intc GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>, + <&pdc 13 IRQ_TYPE_EDGE_RISING>, + <&pdc 12 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "hs_phy_irq", + "dm_hs_phy_irq", "dp_hs_phy_irq"; + + power-domains = <&gcc GCC_USB30_SEC_GDSC>; + + resets = <&gcc GCC_USB30_SEC_BCR>; + + interconnects = <&aggre1_noc MASTER_USB2 0 &mc_virt SLAVE_EBI1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_USB2 0>; + interconnect-names = "usb-ddr", "apps-usb"; + + usb_2_dwc3: usb@8c00000 { + compatible = "snps,dwc3"; + reg = <0 0x08c00000 0 0xe000>; + interrupts = <GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH>; + iommus = <&apps_smmu 0xa0 0x0>; + snps,dis_u2_susphy_quirk; + snps,dis_enblslpm_quirk; + phys = <&usb_2_hsphy>; + phy-names = "usb2-phy"; + maximum-speed = "high-speed"; + }; + }; + dc_noc: interconnect@90e0000 { reg = <0 0x090e0000 0 0x5080>; compatible = "qcom,sc7280-dc-noc"; @@ -1063,6 +1346,55 @@ qcom,bcm-voters = <&apps_bcm_voter>; }; + usb_1: usb@a6f8800 { + compatible = "qcom,sc7280-dwc3", "qcom,dwc3"; + reg = <0 0x0a6f8800 0 0x400>; + status = "disabled"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + dma-ranges; + + clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>, + <&gcc GCC_USB30_PRIM_MASTER_CLK>, + <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>, + <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>, + <&gcc GCC_USB30_PRIM_SLEEP_CLK>; + clock-names = "cfg_noc", "core", "iface", "mock_utmi", + "sleep"; + + assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>, + <&gcc GCC_USB30_PRIM_MASTER_CLK>; + assigned-clock-rates = <19200000>, <200000000>; + + interrupts-extended = <&intc GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>, + <&pdc 14 IRQ_TYPE_EDGE_BOTH>, + <&pdc 15 IRQ_TYPE_EDGE_BOTH>, + <&pdc 17 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hs_phy_irq", "dp_hs_phy_irq", + "dm_hs_phy_irq", "ss_phy_irq"; + + power-domains = <&gcc GCC_USB30_PRIM_GDSC>; + + resets = <&gcc GCC_USB30_PRIM_BCR>; + + interconnects = <&aggre1_noc MASTER_USB3_0 0 &mc_virt SLAVE_EBI1 0>, + <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_USB3_0 0>; + interconnect-names = "usb-ddr", "apps-usb"; + + usb_1_dwc3: usb@a600000 { + compatible = "snps,dwc3"; + reg = <0 0x0a600000 0 0xe000>; + interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; + iommus = <&apps_smmu 0xe0 0x0>; + snps,dis_u2_susphy_quirk; + snps,dis_enblslpm_quirk; + phys = <&usb_1_hsphy>, <&usb_1_ssphy>; + phy-names = "usb2-phy", "usb3-phy"; + maximum-speed = "super-speed"; + }; + }; + videocc: clock-controller@aaf0000 { compatible = "qcom,sc7280-videocc"; reg = <0 0xaaf0000 0 0x10000>; @@ -1185,6 +1517,87 @@ pins = "gpio46", "gpio47"; function = "qup13"; }; + + sdc1_on: sdc1-on { + clk { + pins = "sdc1_clk"; + }; + + cmd { + pins = "sdc1_cmd"; + }; + + data { + pins = "sdc1_data"; + }; + + rclk { + pins = "sdc1_rclk"; + }; + }; + + sdc1_off: sdc1-off { + clk { + pins = "sdc1_clk"; + drive-strength = <2>; + bias-bus-hold; + }; + + cmd { + pins = "sdc1_cmd"; + drive-strength = <2>; + bias-bus-hold; + }; + + data { + pins = "sdc1_data"; + drive-strength = <2>; + bias-bus-hold; + }; + + rclk { + pins = "sdc1_rclk"; + bias-bus-hold; + }; + }; + + sdc2_on: sdc2-on { + clk { + pins = "sdc2_clk"; + }; + + cmd { + pins = "sdc2_cmd"; + }; + + data { + pins = "sdc2_data"; + }; + + sd-cd { + pins = "gpio91"; + }; + }; + + sdc2_off: sdc2-off { + clk { + pins = "sdc2_clk"; + drive-strength = <2>; + bias-bus-hold; + }; + + cmd { + pins ="sdc2_cmd"; + drive-strength = <2>; + bias-bus-hold; + }; + + data { + pins ="sdc2_data"; + drive-strength = <2>; + bias-bus-hold; + }; + }; }; apps_smmu: iommu@15000000 { @@ -1437,9 +1850,9 @@ cpufreq_hw: cpufreq@18591000 { compatible = "qcom,cpufreq-epss"; - reg = <0 0x18591000 0 0x1000>, - <0 0x18592000 0 0x1000>, - <0 0x18593000 0 0x1000>; + reg = <0 0x18591100 0 0x900>, + <0 0x18592100 0 0x900>, + <0 0x18593100 0 0x900>; clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_GPLL0>; clock-names = "xo", "alternate"; #freq-domain-cells = <1>; diff --git a/dts/src/arm64/qcom/sdm630-sony-xperia-ganges-kirin.dts b/dts/src/arm64/qcom/sdm630-sony-xperia-ganges-kirin.dts index 46a7f2b26e..a4e1fb8ca5 100644 --- a/dts/src/arm64/qcom/sdm630-sony-xperia-ganges-kirin.dts +++ b/dts/src/arm64/qcom/sdm630-sony-xperia-ganges-kirin.dts @@ -5,9 +5,21 @@ /dts-v1/; -#include "sdm630-sony-xperia-ganges.dtsi" +#include "sdm630.dtsi" +#include "sdm630-sony-xperia-nile.dtsi" / { model = "Sony Xperia 10"; compatible = "sony,kirin-row", "qcom,sdm630"; + + chosen { + framebuffer@9d400000 { + reg = <0 0x9d400000 0 (2520 * 1080 * 4)>; + height = <2520>; + }; + }; }; + +/* Ganges devices feature a Novatek touchscreen instead. */ +/delete-node/ &touchscreen; +/delete-node/ &vreg_l18a_1v8; diff --git a/dts/src/arm64/qcom/sdm630-sony-xperia-ganges.dtsi b/dts/src/arm64/qcom/sdm630-sony-xperia-ganges.dtsi deleted file mode 100644 index cf2e8b5d60..0000000000 --- a/dts/src/arm64/qcom/sdm630-sony-xperia-ganges.dtsi +++ /dev/null @@ -1,40 +0,0 @@ -// SPDX-License-Identifier: BSD-3-Clause -/* - * Copyright (c) 2020, Martin Botka - */ - -/dts-v1/; - -/* Ganges is very similar to Nile, but - * there are some differences that will need - * to be addresed when more peripherals are - * enabled upstream. Hence the separate DTSI. - */ -#include "sdm630-sony-xperia-nile.dtsi" - -/ { - chosen { - framebuffer@9d400000 { - reg = <0 0x9d400000 0 (2520 * 1080 * 4)>; - height = <2520>; - }; - }; - - /* Yes, this is intentional. - * Ganges devices only use gpio-keys for - * Volume Down, but currently there's an - * issue with it that has to be resolved. - * Until then, let's not make the kernel panic - */ - /delete-node/ gpio-keys; - - soc { - - i2c@c175000 { - status = "okay"; - - /* Novatek touchscreen */ - }; - }; - -}; diff --git a/dts/src/arm64/qcom/sdm630-sony-xperia-nile-discovery.dts b/dts/src/arm64/qcom/sdm630-sony-xperia-nile-discovery.dts index 8fca0b69fa..c574e430ba 100644 --- a/dts/src/arm64/qcom/sdm630-sony-xperia-nile-discovery.dts +++ b/dts/src/arm64/qcom/sdm630-sony-xperia-nile-discovery.dts @@ -5,6 +5,7 @@ /dts-v1/; +#include "sdm630.dtsi" #include "sdm630-sony-xperia-nile.dtsi" / { diff --git a/dts/src/arm64/qcom/sdm630-sony-xperia-nile-pioneer.dts b/dts/src/arm64/qcom/sdm630-sony-xperia-nile-pioneer.dts index 90dcd4ebaa..a93ff3ab1b 100644 --- a/dts/src/arm64/qcom/sdm630-sony-xperia-nile-pioneer.dts +++ b/dts/src/arm64/qcom/sdm630-sony-xperia-nile-pioneer.dts @@ -5,6 +5,7 @@ /dts-v1/; +#include "sdm630.dtsi" #include "sdm630-sony-xperia-nile.dtsi" / { diff --git a/dts/src/arm64/qcom/sdm630-sony-xperia-nile-voyager.dts b/dts/src/arm64/qcom/sdm630-sony-xperia-nile-voyager.dts index fae5f1bb68..59a679c205 100644 --- a/dts/src/arm64/qcom/sdm630-sony-xperia-nile-voyager.dts +++ b/dts/src/arm64/qcom/sdm630-sony-xperia-nile-voyager.dts @@ -5,6 +5,7 @@ /dts-v1/; +#include "sdm630.dtsi" #include "sdm630-sony-xperia-nile.dtsi" / { diff --git a/dts/src/arm64/qcom/sdm630-sony-xperia-nile.dtsi b/dts/src/arm64/qcom/sdm630-sony-xperia-nile.dtsi index 9ba359c848..849900e8b8 100644 --- a/dts/src/arm64/qcom/sdm630-sony-xperia-nile.dtsi +++ b/dts/src/arm64/qcom/sdm630-sony-xperia-nile.dtsi @@ -1,11 +1,10 @@ // SPDX-License-Identifier: BSD-3-Clause /* - * Copyright (c) 2020, Konrad Dybcio + * Copyright (c) 2020, Konrad Dybcio <konrad.dybcio@somainline.org> + * Copyright (c) 2020, AngeloGioacchino Del Regno + * <angelogioacchino.delregno@somainline.org> */ -/dts-v1/; - -#include "sdm630.dtsi" #include "pm660.dtsi" #include "pm660l.dtsi" #include <dt-bindings/gpio/gpio.h> @@ -39,13 +38,61 @@ }; }; + board_vbat: vbat-regulator { + compatible = "regulator-fixed"; + regulator-name = "VBAT"; + + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <4000000>; + regulator-always-on; + regulator-boot-on; + }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "vph_pwr"; + + regulator-always-on; + regulator-boot-on; + }; + + cam_vdig_imx300_219_vreg: cam_vdig_imx300_219_vreg { + compatible = "regulator-fixed"; + regulator-name = "cam_vdig_imx300_219_vreg"; + startup-delay-us = <0>; + enable-active-high; + gpio = <&tlmm 52 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&cam_vdig_default>; + }; + + cam_vana_front_vreg: cam_vana_front_vreg { + compatible = "regulator-fixed"; + regulator-name = "cam_vana_front_vreg"; + startup-delay-us = <0>; + enable-active-high; + gpio = <&tlmm 51 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&imx219_vana_default>; + }; + + cam_vana_rear_vreg: cam_vana_rear_vreg { + compatible = "regulator-fixed"; + regulator-name = "cam_vana_rear_vreg"; + startup-delay-us = <0>; + enable-active-high; + gpio = <&tlmm 50 GPIO_ACTIVE_HIGH>; + regulator-always-on; + pinctrl-names = "default"; + pinctrl-0 = <&imx300_vana_default>; + }; + gpio_keys { status = "okay"; compatible = "gpio-keys"; input-name = "gpio-keys"; #address-cells = <1>; #size-cells = <0>; - autorepeat; camera_focus { label = "Camera Focus"; @@ -100,37 +147,471 @@ }; }; - soc { - sdhci@c0c4000 { - status = "okay"; + /* + * Until we hook up type-c detection, we + * have to stick with this. But it works. + */ + extcon_usb: extcon-usb { + compatible = "linux,extcon-usb-gpio"; + id-gpio = <&tlmm 58 GPIO_ACTIVE_HIGH>; + }; +}; + +&adsp_pil { + firmware-name = "adsp.mdt"; +}; + +&blsp_i2c1 { + status = "okay"; + + touchscreen: synaptics-rmi4-i2c@70 { + compatible = "syna,rmi4-i2c"; + reg = <0x70>; + #address-cells = <1>; + #size-cells = <0>; + interrupts-extended = <&tlmm 45 0x2008>; - mmc-ddr-1_8v; - /* SoMC Nile platform's eMMC doesn't support HS200 mode */ - mmc-hs400-1_8v; + pinctrl-names = "default"; + pinctrl-0 = <&ts_int_active &ts_lcd_id_active>; + + syna,reset-delay-ms = <200>; + syna,startup-delay-ms = <220>; + + rmi4-f01@1 { + reg = <0x01>; + syna,nosleep-mode = <1>; }; - i2c@c175000 { - status = "okay"; + rmi4-f11@11 { + reg = <0x11>; + syna,sensor-type = <1>; + }; + }; +}; + +&blsp_i2c2 { + status = "okay"; + + /* SMB1351 charger */ +}; + +/* I2C3, 4, 5, 7 and 8 are disabled on this board. */ + +&blsp_i2c6 { + status = "okay"; + + /* NXP NFC */ +}; + +&blsp1_uart2 { + status = "okay"; + + /* MSM serial console */ +}; + +&blsp2_uart1 { + status = "okay"; - /* Synaptics touchscreen */ + /* HCI Bluetooth */ +}; + +&pon { + volup { + compatible = "qcom,pm8941-resin"; + interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>; + debounce = <15625>; + bias-pull-up; + linux,code = <KEY_VOLUMEUP>; + }; +}; + +&qusb2phy { + status = "okay"; + + vdd-supply = <&vreg_l1b_0p925>; + vdda-pll-supply = <&vreg_l10a_1p8>; + vdda-phy-dpdm-supply = <&vreg_l7b_3p125>; +}; + +&rpm_requests { + pm660l-regulators { + compatible = "qcom,rpm-pm660l-regulators"; + + vdd_s1-supply = <&vph_pwr>; + vdd_s2-supply = <&vph_pwr>; + vdd_s3_s4-supply = <&vph_pwr>; + vdd_s5-supply = <&vph_pwr>; + vdd_s6-supply = <&vph_pwr>; + + vdd_l1_l9_l10-supply = <&vreg_s2b_1p05>; + vdd_l2-supply = <&vreg_bob>; + vdd_l3_l5_l7_l8-supply = <&vreg_bob>; + vdd_l4_l6-supply = <&vreg_bob>; + vdd_bob-supply = <&vph_pwr>; + + vreg_s1b_1p125: s1 { + regulator-min-microvolt = <1125000>; + regulator-max-microvolt = <1125000>; + regulator-enable-ramp-delay = <200>; + regulator-ramp-delay = <0>; }; - i2c@c176000 { - status = "okay"; + vreg_s2b_1p05: s2 { + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + regulator-enable-ramp-delay = <200>; + regulator-ramp-delay = <0>; + }; + + /* + * At least on Nile's configuration, S3B/S4B (VDD_CX) and + * S5B (VDD_MX) are managed only through RPM Power Domains. + * Trying to set a voltage on the main supply will create + * havoc and freeze the SoC. + * In any case, reference voltages for these regulators are: + * S3B/S4B: 0.870V + * S5B: 0.915V + */ - /* SMB1351 charger */ + /* LDOs */ + vreg_l1b_0p925: l1 { + regulator-min-microvolt = <920000>; + regulator-max-microvolt = <928000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + regulator-allow-set-load; }; - serial@c1af000 { - status = "okay"; + vreg_l2b_2p95: l2 { + /* + * This regulator supports 1.648 - 3.104V on this board + * but we set a max voltage of anything less than 2.7V + * to satisfy a condition in sdhci.c that will disable + * 3.3V SDHCI signaling, which happens to be not really + * supported on the Xperia Nile/Ganges platform. + */ + regulator-min-microvolt = <1648000>; + regulator-max-microvolt = <2696000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + regulator-allow-set-load; }; - /* I2C3, 4, 5, 7 and 8 are disabled on this board. */ + vreg_l3b_3p0: l3 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + regulator-min-microamp = <200>; + regulator-max-microamp = <600000>; + regulator-system-load = <100000>; + regulator-allow-set-load; + }; - i2c@c1b6000 { - status = "okay"; + vreg_l4b_29p5: l4 { + regulator-min-microvolt = <2944000>; + regulator-max-microvolt = <2952000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + + regulator-min-microamp = <200>; + regulator-max-microamp = <600000>; + regulator-system-load = <570000>; + regulator-allow-set-load; + }; + + /* + * Downstream specifies a range of 1721-3600mV, + * but the only assigned consumers are SDHCI2 VMMC + * and Coresight QPDI that both request pinned 2.95V. + * Tighten the range to 1.8-3.328 (closest to 3.3) to + * make the mmc driver happy. + */ + vreg_l5b_29p5: l5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3328000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + regulator-allow-set-load; + regulator-system-load = <800000>; + }; + + vreg_l6b_3p3: l6 { + regulator-min-microvolt = <1704000>; + regulator-max-microvolt = <3312000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + }; + + vreg_l7b_3p125: l7 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <3128000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + }; + + vreg_l8b_3p3: l8 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <3400000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + }; + + /* L9B (870mV) is currently unused */ + /* L10B (915mV) is currently unused */ + + vreg_bob: bob { + regulator-min-microvolt = <3304000>; + regulator-max-microvolt = <3624000>; + regulator-enable-ramp-delay = <500>; + regulator-ramp-delay = <0>; + }; + }; + + pm660-regulators { + compatible = "qcom,rpm-pm660-regulators"; + + vdd_s1-supply = <&vph_pwr>; + vdd_s2-supply = <&vph_pwr>; + vdd_s3-supply = <&vph_pwr>; + vdd_s4-supply = <&vph_pwr>; + vdd_s5-supply = <&vph_pwr>; + vdd_s6-supply = <&vph_pwr>; + + vdd_l1_l6_l7-supply = <&vreg_s5a_1p35>; + vdd_l2_l3-supply = <&vreg_s2b_1p05>; + vdd_l5-supply = <&vreg_s2b_1p05>; + vdd_l8_l9_l10_l11_l12_l13_l14-supply = <&vreg_s4a_2p04>; + vdd_l15_l16_l17_l18_l19-supply = <&vreg_bob>; + + /* + * S1A (FTAPC0), S2A (FTAPC1), S3A (HFAPC1) are managed + * by the Core Power Reduction hardened (CPRh) and the + * Operating State Manager (OSM) HW automatically. + */ + + vreg_s4a_2p04: s4 { + regulator-min-microvolt = <2040000>; + regulator-max-microvolt = <2040000>; + regulator-enable-ramp-delay = <200>; + regulator-ramp-delay = <0>; + regulator-always-on; + }; + + vreg_s5a_1p35: s5 { + regulator-min-microvolt = <1224000>; + regulator-max-microvolt = <1350000>; + regulator-enable-ramp-delay = <200>; + regulator-ramp-delay = <0>; + }; + + vreg_s6a_0p87: s6 { + regulator-min-microvolt = <504000>; + regulator-max-microvolt = <992000>; + regulator-enable-ramp-delay = <150>; + regulator-ramp-delay = <0>; + }; + + /* LDOs */ + vreg_l1a_1p225: l1 { + regulator-min-microvolt = <1226000>; + regulator-max-microvolt = <1250000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + regulator-allow-set-load; + }; + + vreg_l2a_1p0: l2 { + regulator-min-microvolt = <944000>; + regulator-max-microvolt = <1008000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + }; + + vreg_l3a_1p0: l3 { + regulator-min-microvolt = <944000>; + regulator-max-microvolt = <1008000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + }; + + vreg_l5a_0p848: l5 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <952000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + }; + + vreg_l6a_1p3: l6 { + regulator-min-microvolt = <1304000>; + regulator-max-microvolt = <1368000>; + regulator-allow-set-load; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + }; + + vreg_l7a_1p2: l7 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + }; + + vreg_l8a_1p8: l8 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + regulator-system-load = <325000>; + regulator-allow-set-load; + }; + + vreg_l9a_1p8: l9 { + regulator-min-microvolt = <1804000>; + regulator-max-microvolt = <1896000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + regulator-allow-set-load; + }; + + vreg_l10a_1p8: l10 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1944000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + regulator-allow-set-load; + }; + + vreg_l11a_1p8: l11 { + regulator-min-microvolt = <1784000>; + regulator-max-microvolt = <1944000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + }; + + vreg_l12a_1p8: l12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1944000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + }; - /* NXP NFC */ + /* This gives power to the LPDDR4: never turn it off! */ + vreg_l13a_1p8: l13 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1944000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + regulator-boot-on; + regulator-always-on; }; + + vreg_l14a_1p8: l14 { + regulator-min-microvolt = <1710000>; + regulator-max-microvolt = <1904000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + }; + + vreg_l15a_1p8: l15 { + regulator-min-microvolt = <1648000>; + regulator-max-microvolt = <2952000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + }; + + /* L16A (2.70V) is unused */ + + vreg_l17a_1p8: l17 { + regulator-min-microvolt = <1648000>; + regulator-max-microvolt = <2952000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + }; + + vreg_l18a_1v8: l18 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <10>; + regulator-min-microamp = <200>; + regulator-max-microamp = <50000>; + regulator-system-load = <10000>; + regulator-allow-set-load; + }; + + vreg_l19a_3p3: l19 { + regulator-min-microvolt = <3312000>; + regulator-max-microvolt = <3400000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + regulator-allow-set-load; + }; + }; +}; + +&sdhc_1 { + status = "okay"; + supports-cqe; + + /* SoMC Nile platform's eMMC doesn't support HS200 mode */ + mmc-ddr-1_8v; + mmc-hs400-1_8v; + mmc-hs400-enhanced-strobe; + + vmmc-supply = <&vreg_l4b_29p5>; + vqmmc-supply = <&vreg_l8a_1p8>; +}; + +&sdhc_2 { + status = "okay"; + + vmmc-supply = <&vreg_l5b_29p5>; + vqmmc-supply = <&vreg_l2b_2p95>; +}; + +&tlmm { + gpio-reserved-ranges = <8 4>; + + ts_int_active: ts-int-active { + pins = "gpio45"; + drive-strength = <8>; + bias-pull-up; + }; + + ts_lcd_id_active: ts-lcd-id-active { + pins = "gpio56"; + drive-strength = <8>; + bias-disable; + }; + + imx300_vana_default: imx300-vana-default { + pins = "gpio50"; + function = "gpio"; + bias-disable; + drive-strength = <2>; }; + + imx219_vana_default: imx219-vana-default { + pins = "gpio51"; + function = "gpio"; + bias-disable; + drive-strength = <2>; + }; + + cam_vdig_default: cam-vdig-default { + pins = "gpio52"; + function = "gpio"; + bias-disable; + drive-strength = <2>; + }; +}; + +&usb3 { + status = "okay"; +}; + +&usb3_dwc3 { + dr_mode = "peripheral"; + extcon = <&extcon_usb>; }; diff --git a/dts/src/arm64/qcom/sdm630.dtsi b/dts/src/arm64/qcom/sdm630.dtsi index f91a928466..9153e6616b 100644 --- a/dts/src/arm64/qcom/sdm630.dtsi +++ b/dts/src/arm64/qcom/sdm630.dtsi @@ -1,12 +1,17 @@ // SPDX-License-Identifier: BSD-3-Clause /* - * Copyright (c) 2020, Konrad Dybcio + * Copyright (c) 2020, Konrad Dybcio <konradybcio@gmail.com> + * Copyright (c) 2020, AngeloGioacchino Del Regno <kholk11@gmail.com> */ #include <dt-bindings/clock/qcom,gcc-sdm660.h> +#include <dt-bindings/clock/qcom,gpucc-sdm660.h> +#include <dt-bindings/clock/qcom,mmcc-sdm660.h> #include <dt-bindings/clock/qcom,rpmcc.h> +#include <dt-bindings/power/qcom-rpmpd.h> #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/soc/qcom,apr.h> / { interrupt-parent = <&intc>; @@ -17,14 +22,14 @@ chosen { }; clocks { - xo_board: xo_board { + xo_board: xo-board { compatible = "fixed-clock"; #clock-cells = <0>; clock-frequency = <19200000>; clock-output-names = "xo_board"; }; - sleep_clk: sleep_clk { + sleep_clk: sleep-clk { compatible = "fixed-clock"; #clock-cells = <0>; clock-frequency = <32764>; @@ -311,10 +316,10 @@ }; }; - memory { + memory@80000000 { device_type = "memory"; /* We expect the bootloader to fill in the reg */ - reg = <0 0 0 0>; + reg = <0x0 0x80000000 0x0 0x0>; }; pmu { @@ -343,10 +348,19 @@ }; qhee_code: qhee-code@85800000 { - reg = <0x0 0x85800000 0x0 0x3700000>; + reg = <0x0 0x85800000 0x0 0x600000>; no-map; }; + rmtfs_mem: memory@85e00000 { + compatible = "qcom,rmtfs-mem"; + reg = <0x0 0x85e00000 0x0 0x200000>; + no-map; + + qcom,client-id = <1>; + qcom,vmid = <15>; + }; + smem_region: smem-mem@86000000 { reg = <0 0x86000000 0 0x200000>; no-map; @@ -357,58 +371,44 @@ no-map; }; - modem_fw_mem: modem-fw-region@8ac00000 { + mpss_region: mpss@8ac00000 { reg = <0x0 0x8ac00000 0x0 0x7e00000>; no-map; }; - adsp_fw_mem: adsp-fw-region@92a00000 { + adsp_region: adsp@92a00000 { reg = <0x0 0x92a00000 0x0 0x1e00000>; no-map; }; - pil_mba_mem: pil-mba-region@94800000 { + mba_region: mba@94800000 { reg = <0x0 0x94800000 0x0 0x200000>; no-map; }; - buffer_mem: buffer-region@94a00000 { + buffer_mem: tzbuffer@94a00000 { reg = <0x0 0x94a00000 0x0 0x100000>; no-map; }; - venus_fw_mem: venus-fw-region@9f800000 { + venus_region: venus@9f800000 { reg = <0x0 0x9f800000 0x0 0x800000>; no-map; }; - secure_region2: secure-region2@f7c00000 { - reg = <0x0 0xf7c00000 0x0 0x5c00000>; - no-map; - }; - adsp_mem: adsp-region@f6000000 { reg = <0x0 0xf6000000 0x0 0x800000>; no-map; }; - qseecom_ta_mem: qseecom-ta-region@fec00000 { - reg = <0x0 0xfec00000 0x0 0x1000000>; - no-map; - }; - qseecom_mem: qseecom-region@f6800000 { reg = <0x0 0xf6800000 0x0 0x1400000>; no-map; }; - secure_display_memory: secure-region@f5c00000 { - reg = <0x0 0xf5c00000 0x0 0x5c00000>; - no-map; - }; - - cont_splash_mem: cont-splash-region@9d400000 { - reg = <0x0 0x9d400000 0x0 0x23ff000>; + zap_shader_region: gpu@fed00000 { + compatible = "shared-dma-pool"; + reg = <0x0 0xfed00000 0x0 0xa00000>; no-map; }; }; @@ -428,6 +428,52 @@ compatible = "qcom,rpmcc-sdm660", "qcom,rpmcc"; #clock-cells = <1>; }; + + rpmpd: power-controller { + compatible = "qcom,sdm660-rpmpd"; + #power-domain-cells = <1>; + operating-points-v2 = <&rpmpd_opp_table>; + + rpmpd_opp_table: opp-table { + compatible = "operating-points-v2"; + + rpmpd_opp_ret: opp1 { + opp-level = <RPM_SMD_LEVEL_RETENTION>; + }; + + rpmpd_opp_ret_plus: opp2 { + opp-level = <RPM_SMD_LEVEL_RETENTION_PLUS>; + }; + + rpmpd_opp_min_svs: opp3 { + opp-level = <RPM_SMD_LEVEL_MIN_SVS>; + }; + + rpmpd_opp_low_svs: opp4 { + opp-level = <RPM_SMD_LEVEL_LOW_SVS>; + }; + + rpmpd_opp_svs: opp5 { + opp-level = <RPM_SMD_LEVEL_SVS>; + }; + + rpmpd_opp_svs_plus: opp6 { + opp-level = <RPM_SMD_LEVEL_SVS_PLUS>; + }; + + rpmpd_opp_nom: opp7 { + opp-level = <RPM_SMD_LEVEL_NOM>; + }; + + rpmpd_opp_nom_plus: opp8 { + opp-level = <RPM_SMD_LEVEL_NOM_PLUS>; + }; + + rpmpd_opp_turbo: opp9 { + opp-level = <RPM_SMD_LEVEL_TURBO>; + }; + }; + }; }; }; @@ -437,6 +483,46 @@ hwlocks = <&tcsr_mutex 3>; }; + smp2p-adsp { + compatible = "qcom,smp2p"; + qcom,smem = <443>, <429>; + interrupts = <GIC_SPI 158 IRQ_TYPE_EDGE_RISING>; + mboxes = <&apcs_glb 10>; + qcom,local-pid = <0>; + qcom,remote-pid = <2>; + + adsp_smp2p_out: master-kernel { + qcom,entry-name = "master-kernel"; + #qcom,smem-state-cells = <1>; + }; + + adsp_smp2p_in: slave-kernel { + qcom,entry-name = "slave-kernel"; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + + smp2p-mpss { + compatible = "qcom,smp2p"; + qcom,smem = <435>, <428>; + interrupts = <GIC_SPI 451 IRQ_TYPE_EDGE_RISING>; + mboxes = <&apcs_glb 14>; + qcom,local-pid = <0>; + qcom,remote-pid = <1>; + + modem_smp2p_out: master-kernel { + qcom,entry-name = "master-kernel"; + #qcom,smem-state-cells = <1>; + }; + + modem_smp2p_in: slave-kernel { + qcom,entry-name = "slave-kernel"; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + soc { #address-cells = <1>; #size-cells = <1>; @@ -465,6 +551,16 @@ reg = <0x00780000 0x621c>; #address-cells = <1>; #size-cells = <1>; + + qusb2_hstx_trim: hstx-trim@240 { + reg = <0x240 0x1>; + bits = <25 3>; + }; + + gpu_speed_bin: gpu-speed-bin@41a0 { + reg = <0x41a0 0x1>; + bits = <21 7>; + }; }; rng: rng@793000 { @@ -474,17 +570,49 @@ clock-names = "core"; }; + bimc: interconnect@1008000 { + compatible = "qcom,sdm660-bimc"; + reg = <0x01008000 0x78000>; + #interconnect-cells = <1>; + clock-names = "bus", "bus_a"; + clocks = <&rpmcc RPM_SMD_BIMC_CLK>, + <&rpmcc RPM_SMD_BIMC_A_CLK>; + }; + restart@10ac000 { compatible = "qcom,pshold"; reg = <0x010ac000 0x4>; }; + cnoc: interconnect@1500000 { + compatible = "qcom,sdm660-cnoc"; + reg = <0x01500000 0x10000>; + #interconnect-cells = <1>; + clock-names = "bus", "bus_a"; + clocks = <&rpmcc RPM_SMD_CNOC_CLK>, + <&rpmcc RPM_SMD_CNOC_A_CLK>; + }; + + snoc: interconnect@1626000 { + compatible = "qcom,sdm660-snoc"; + reg = <0x01626000 0x7090>; + #interconnect-cells = <1>; + clock-names = "bus", "bus_a"; + clocks = <&rpmcc RPM_SMD_SNOC_CLK>, + <&rpmcc RPM_SMD_SNOC_A_CLK>; + }; + anoc2_smmu: iommu@16c0000 { compatible = "qcom,sdm630-smmu-v2", "qcom,smmu-v2"; reg = <0x016c0000 0x40000>; - #iommu-cells = <1>; + assigned-clocks = <&rpmcc RPM_SMD_AGGR2_NOC_CLK>; + assigned-clock-rates = <1000>; + clocks = <&rpmcc RPM_SMD_AGGR2_NOC_CLK>; + clock-names = "bus"; #global-interrupts = <2>; + #iommu-cells = <1>; + interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>, @@ -522,19 +650,53 @@ status = "disabled"; }; + a2noc: interconnect@1704000 { + compatible = "qcom,sdm660-a2noc"; + reg = <0x01704000 0xc100>; + #interconnect-cells = <1>; + clock-names = "bus", "bus_a"; + clocks = <&rpmcc RPM_SMD_AGGR2_NOC_CLK>, + <&rpmcc RPM_SMD_AGGR2_NOC_A_CLK>; + }; + + mnoc: interconnect@1745000 { + compatible = "qcom,sdm660-mnoc"; + reg = <0x01745000 0xA010>; + #interconnect-cells = <1>; + clock-names = "bus", "bus_a", "iface"; + clocks = <&rpmcc RPM_SMD_MMSSNOC_AXI_CLK>, + <&rpmcc RPM_SMD_MMSSNOC_AXI_CLK_A>, + <&mmcc AHB_CLK_SRC>; + }; + + tsens: thermal-sensor@10ae000 { + compatible = "qcom,sdm630-tsens", "qcom,tsens-v2"; + reg = <0x010ae000 0x1000>, /* TM */ + <0x010ad000 0x1000>; /* SROT */ + #qcom,sensors = <12>; + interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 430 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "uplow", "critical"; + #thermal-sensor-cells = <1>; + }; + tcsr_mutex_regs: syscon@1f40000 { compatible = "syscon"; - reg = <0x01f40000 0x20000>; + reg = <0x01f40000 0x40000>; }; - tlmm: pinctrl@3000000 { + tlmm: pinctrl@3100000 { compatible = "qcom,sdm630-pinctrl"; - reg = <0x03000000 0xc00000>; + reg = <0x03100000 0x400000>, + <0x03500000 0x400000>, + <0x03900000 0x400000>; + reg-names = "south", "center", "north"; interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; - #gpio-cells = <0x2>; + gpio-ranges = <&tlmm 0 0 114>; + #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <0x2>; + #interrupt-cells = <2>; blsp1_uart1_default: blsp1-uart1-default { pins = "gpio0", "gpio1", "gpio2", "gpio3"; @@ -554,191 +716,392 @@ bias-disable; }; - blsp2_uart1_tx_active: blsp2-uart1-tx-active { - pins = "gpio16"; - drive-strength = <2>; - bias-disable; - }; - - blsp2_uart1_tx_sleep: blsp2-uart1-tx-sleep { - pins = "gpio16"; - drive-strength = <2>; - bias-pull-up; - }; + blsp2_uart1_default: blsp2-uart1-active { + tx-rts { + pins = "gpio16", "gpio19"; + function = "blsp_uart5"; + drive-strength = <2>; + bias-disable; + }; - blsp2_uart1_rxcts_active: blsp2-uart1-rxcts-active { - pins = "gpio17", "gpio18"; - drive-strength = <2>; - bias-disable; - }; + rx { + /* + * Avoid garbage data while BT module + * is powered off or not driving signal + */ + pins = "gpio17"; + function = "blsp_uart5"; + drive-strength = <2>; + bias-pull-up; + }; - blsp2_uart1_rxcts_sleep: blsp2-uart1-rxcts-sleep { - pins = "gpio17", "gpio18"; - drive-strength = <2>; - bias-no-pull; + cts { + /* Match the pull of the BT module */ + pins = "gpio18"; + function = "blsp_uart5"; + drive-strength = <2>; + bias-pull-down; + }; }; - blsp2_uart1_rfr_active: blsp2-uart1-rfr-active { - pins = "gpio19"; - drive-strength = <2>; - bias-disable; - }; + blsp2_uart1_sleep: blsp2-uart1-sleep { + tx { + pins = "gpio16"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; - blsp2_uart1_rfr_sleep: blsp2-uart1-rfr-sleep { - pins = "gpio19"; - drive-strength = <2>; - bias-no-pull; + rx-cts-rts { + pins = "gpio17", "gpio18", "gpio19"; + function = "gpio"; + drive-strength = <2>; + bias-no-pull; + }; }; i2c1_default: i2c1-default { pins = "gpio2", "gpio3"; + function = "blsp_i2c1"; drive-strength = <2>; bias-disable; }; i2c1_sleep: i2c1-sleep { pins = "gpio2", "gpio3"; + function = "blsp_i2c1"; drive-strength = <2>; bias-pull-up; }; i2c2_default: i2c2-default { pins = "gpio6", "gpio7"; + function = "blsp_i2c2"; drive-strength = <2>; bias-disable; }; i2c2_sleep: i2c2-sleep { pins = "gpio6", "gpio7"; + function = "blsp_i2c2"; drive-strength = <2>; bias-pull-up; }; i2c3_default: i2c3-default { pins = "gpio10", "gpio11"; + function = "blsp_i2c3"; drive-strength = <2>; bias-disable; }; i2c3_sleep: i2c3-sleep { pins = "gpio10", "gpio11"; + function = "blsp_i2c3"; drive-strength = <2>; bias-pull-up; }; i2c4_default: i2c4-default { pins = "gpio14", "gpio15"; + function = "blsp_i2c4"; drive-strength = <2>; bias-disable; }; i2c4_sleep: i2c4-sleep { pins = "gpio14", "gpio15"; + function = "blsp_i2c4"; drive-strength = <2>; bias-pull-up; }; i2c5_default: i2c5-default { pins = "gpio18", "gpio19"; + function = "blsp_i2c5"; drive-strength = <2>; bias-disable; }; i2c5_sleep: i2c5-sleep { pins = "gpio18", "gpio19"; + function = "blsp_i2c5"; drive-strength = <2>; bias-pull-up; }; i2c6_default: i2c6-default { pins = "gpio22", "gpio23"; + function = "blsp_i2c6"; drive-strength = <2>; bias-disable; }; i2c6_sleep: i2c6-sleep { pins = "gpio22", "gpio23"; + function = "blsp_i2c6"; drive-strength = <2>; bias-pull-up; }; i2c7_default: i2c7-default { pins = "gpio26", "gpio27"; + function = "blsp_i2c7"; drive-strength = <2>; bias-disable; }; i2c7_sleep: i2c7-sleep { pins = "gpio26", "gpio27"; + function = "blsp_i2c7"; drive-strength = <2>; bias-pull-up; }; i2c8_default: i2c8-default { pins = "gpio30", "gpio31"; + function = "blsp_i2c8"; drive-strength = <2>; bias-disable; }; i2c8_sleep: i2c8-sleep { pins = "gpio30", "gpio31"; + function = "blsp_i2c8"; drive-strength = <2>; bias-pull-up; }; - sdc1_clk_on: sdc1-clk-on { - pins = "sdc1_clk"; - bias-disable; - drive-strength = <16>; - }; + cci0_default: cci0_default { + pinmux { + pins = "gpio36","gpio37"; + function = "cci_i2c"; + }; - sdc1_clk_off: sdc1-clk-off { - pins = "sdc1_clk"; - bias-disable; - drive-strength = <2>; + pinconf { + pins = "gpio36","gpio37"; + bias-pull-up; + drive-strength = <2>; + }; }; - sdc1_cmd_on: sdc1-cmd-on { - pins = "sdc1_cmd"; - bias-pull-up; - drive-strength = <10>; + cci1_default: cci1_default { + pinmux { + pins = "gpio38","gpio39"; + function = "cci_i2c"; + }; + + pinconf { + pins = "gpio38","gpio39"; + bias-pull-up; + drive-strength = <2>; + }; }; - sdc1_cmd_off: sdc1-cmd-off { - pins = "sdc1_cmd"; - bias-pull-up; - drive-strength = <2>; + sdc1_state_on: sdc1-on { + clk { + pins = "sdc1_clk"; + bias-disable; + drive-strength = <16>; + }; + + cmd { + pins = "sdc1_cmd"; + bias-pull-up; + drive-strength = <10>; + }; + + data { + pins = "sdc1_data"; + bias-pull-up; + drive-strength = <10>; + }; + + rclk { + pins = "sdc1_rclk"; + bias-pull-down; + }; }; - sdc1_data_on: sdc1-data-on { - pins = "sdc1_data"; - bias-pull-up; - drive-strength = <8>; + sdc1_state_off: sdc1-off { + clk { + pins = "sdc1_clk"; + bias-disable; + drive-strength = <2>; + }; + + cmd { + pins = "sdc1_cmd"; + bias-pull-up; + drive-strength = <2>; + }; + + data { + pins = "sdc1_data"; + bias-pull-up; + drive-strength = <2>; + }; + + rclk { + pins = "sdc1_rclk"; + bias-pull-down; + }; }; - sdc1_data_off: sdc1-data-off { - pins = "sdc1_data"; - bias-pull-up; - drive-strength = <2>; + sdc2_state_on: sdc2-on { + clk { + pins = "sdc2_clk"; + bias-disable; + drive-strength = <16>; + }; + + cmd { + pins = "sdc2_cmd"; + bias-pull-up; + drive-strength = <10>; + }; + + data { + pins = "sdc2_data"; + bias-pull-up; + drive-strength = <10>; + }; + + sd-cd { + pins = "gpio54"; + bias-pull-up; + drive-strength = <2>; + }; }; - sdc1_rclk_on: sdc1-rclk-on { - pins = "sdc1_rclk"; - bias-pull-down; + sdc2_state_off: sdc2-off { + clk { + pins = "sdc2_clk"; + bias-disable; + drive-strength = <2>; + }; + + cmd { + pins = "sdc2_cmd"; + bias-pull-up; + drive-strength = <2>; + }; + + data { + pins = "sdc2_data"; + bias-pull-up; + drive-strength = <2>; + }; + + sd-cd { + pins = "gpio54"; + bias-disable; + drive-strength = <2>; + }; }; + }; + + adreno_gpu: gpu@5000000 { + compatible = "qcom,adreno-508.0", "qcom,adreno"; + #stream-id-cells = <16>; + + reg = <0x05000000 0x40000>; + reg-names = "kgsl_3d0_reg_memory"; - sdc1_rclk_off: sdc1-rclk-off { - pins = "sdc1_rclk"; - bias-pull-down; + interrupts = <0 300 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_GPU_CFG_AHB_CLK>, + <&gpucc GPUCC_RBBMTIMER_CLK>, + <&gcc GCC_BIMC_GFX_CLK>, + <&gcc GCC_GPU_BIMC_GFX_CLK>, + <&gpucc GPUCC_RBCPR_CLK>, + <&gpucc GPUCC_GFX3D_CLK>; + + clock-names = "iface", + "rbbmtimer", + "mem", + "mem_iface", + "rbcpr", + "core"; + + power-domains = <&rpmpd SDM660_VDDMX>; + iommus = <&kgsl_smmu 0>; + + nvmem-cells = <&gpu_speed_bin>; + nvmem-cell-names = "speed_bin"; + + interconnects = <&gnoc 1 &bimc 5>; + interconnect-names = "gfx-mem"; + + operating-points-v2 = <&gpu_sdm630_opp_table>; + + gpu_sdm630_opp_table: opp-table { + compatible = "operating-points-v2"; + opp-775000000 { + opp-hz = /bits/ 64 <775000000>; + opp-level = <RPM_SMD_LEVEL_TURBO>; + opp-peak-kBps = <5412000>; + opp-supported-hw = <0xA2>; + }; + opp-647000000 { + opp-hz = /bits/ 64 <647000000>; + opp-level = <RPM_SMD_LEVEL_NOM_PLUS>; + opp-peak-kBps = <4068000>; + opp-supported-hw = <0xFF>; + }; + opp-588000000 { + opp-hz = /bits/ 64 <588000000>; + opp-level = <RPM_SMD_LEVEL_NOM>; + opp-peak-kBps = <3072000>; + opp-supported-hw = <0xFF>; + }; + opp-465000000 { + opp-hz = /bits/ 64 <465000000>; + opp-level = <RPM_SMD_LEVEL_SVS_PLUS>; + opp-peak-kBps = <2724000>; + opp-supported-hw = <0xFF>; + }; + opp-370000000 { + opp-hz = /bits/ 64 <370000000>; + opp-level = <RPM_SMD_LEVEL_SVS>; + opp-peak-kBps = <2188000>; + opp-supported-hw = <0xFF>; + }; + opp-240000000 { + opp-hz = /bits/ 64 <240000000>; + opp-level = <RPM_SMD_LEVEL_LOW_SVS>; + opp-peak-kBps = <1648000>; + opp-supported-hw = <0xFF>; + }; + opp-160000000 { + opp-hz = /bits/ 64 <160000000>; + opp-level = <RPM_SMD_LEVEL_MIN_SVS>; + opp-peak-kBps = <1200000>; + opp-supported-hw = <0xFF>; + }; }; }; kgsl_smmu: iommu@5040000 { - compatible = "qcom,sdm630-smmu-v2", "qcom,smmu-v2"; + compatible = "qcom,sdm630-smmu-v2", + "qcom,adreno-smmu", "qcom,smmu-v2"; reg = <0x05040000 0x10000>; - #iommu-cells = <1>; + /* + * GX GDSC parent is CX. We need to bring up CX for SMMU + * but we need both up for Adreno. On the other hand, we + * need to manage the GX rpmpd domain in the adreno driver. + * Enable CX/GX GDSCs here so that we can manage just the GX + * RPM Power Domain in the Adreno driver. + */ + power-domains = <&gpucc GPU_GX_GDSC>; + clocks = <&gcc GCC_GPU_CFG_AHB_CLK>, + <&gcc GCC_BIMC_GFX_CLK>, + <&gcc GCC_GPU_BIMC_GFX_CLK>; + clock-names = "iface", "mem", "mem_iface"; #global-interrupts = <2>; + #iommu-cells = <1>; + interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>, @@ -755,6 +1118,22 @@ status = "disabled"; }; + gpucc: clock-controller@5065000 { + compatible = "qcom,gpucc-sdm630"; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + reg = <0x05065000 0x9038>; + + clocks = <&xo_board>, + <&gcc GCC_GPU_GPLL0_CLK>, + <&gcc GCC_GPU_GPLL0_DIV_CLK>; + clock-names = "xo", + "gcc_gpu_gpll0_clk", + "gcc_gpu_gpll0_div_clk"; + status = "disabled"; + }; + lpass_smmu: iommu@5100000 { compatible = "qcom,sdm630-smmu-v2", "qcom,smmu-v2"; reg = <0x05100000 0x40000>; @@ -805,6 +1184,120 @@ cell-index = <0>; }; + usb3: usb@a8f8800 { + compatible = "qcom,sdm660-dwc3", "qcom,dwc3"; + reg = <0x0a8f8800 0x400>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + clocks = <&gcc GCC_CFG_NOC_USB3_AXI_CLK>, + <&gcc GCC_USB30_MASTER_CLK>, + <&gcc GCC_AGGRE2_USB3_AXI_CLK>, + <&rpmcc RPM_SMD_AGGR2_NOC_CLK>, + <&gcc GCC_USB30_MOCK_UTMI_CLK>, + <&gcc GCC_USB30_SLEEP_CLK>; + clock-names = "cfg_noc", "core", "iface", "bus", + "mock_utmi", "sleep"; + + assigned-clocks = <&gcc GCC_USB30_MOCK_UTMI_CLK>, + <&gcc GCC_USB30_MASTER_CLK>, + <&rpmcc RPM_SMD_AGGR2_NOC_CLK>; + assigned-clock-rates = <19200000>, <120000000>, + <19200000>; + + interrupts = <GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hs_phy_irq", "ss_phy_irq"; + + power-domains = <&gcc USB_30_GDSC>; + qcom,select-utmi-as-pipe-clk; + + resets = <&gcc GCC_USB_30_BCR>; + + usb3_dwc3: usb@a800000 { + compatible = "snps,dwc3"; + reg = <0x0a800000 0xc8d0>; + interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>; + snps,dis_u2_susphy_quirk; + snps,dis_enblslpm_quirk; + + /* + * SDM630 technically supports USB3 but I + * haven't seen any devices making use of it. + */ + maximum-speed = "high-speed"; + phys = <&qusb2phy>; + phy-names = "usb2-phy"; + snps,hird-threshold = /bits/ 8 <0>; + }; + }; + + qusb2phy: phy@c012000 { + compatible = "qcom,sdm660-qusb2-phy"; + reg = <0x0c012000 0x180>; + #phy-cells = <0>; + + clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>, + <&gcc GCC_RX1_USB2_CLKREF_CLK>; + clock-names = "cfg_ahb", "ref"; + + resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>; + nvmem-cells = <&qusb2_hstx_trim>; + status = "disabled"; + }; + + sdhc_2: sdhci@c084000 { + compatible = "qcom,sdm630-sdhci", "qcom,sdhci-msm-v5"; + reg = <0x0c084000 0x1000>; + reg-names = "hc"; + + interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hc_irq", "pwr_irq"; + + bus-width = <4>; + clocks = <&gcc GCC_SDCC2_APPS_CLK>, + <&gcc GCC_SDCC2_AHB_CLK>, + <&xo_board>; + clock-names = "core", "iface", "xo"; + + interconnects = <&a2noc 3 &a2noc 10>, + <&gnoc 0 &cnoc 28>; + operating-points-v2 = <&sdhc2_opp_table>; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc2_state_on>; + pinctrl-1 = <&sdc2_state_off>; + power-domains = <&rpmpd SDM660_VDDCX>; + + status = "disabled"; + + sdhc2_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-50000000 { + opp-hz = /bits/ 64 <50000000>; + required-opps = <&rpmpd_opp_low_svs>; + opp-peak-kBps = <200000 140000>; + opp-avg-kBps = <130718 133320>; + }; + opp-100000000 { + opp-hz = /bits/ 64 <100000000>; + required-opps = <&rpmpd_opp_svs>; + opp-peak-kBps = <250000 160000>; + opp-avg-kBps = <196078 150000>; + }; + opp-200000000 { + opp-hz = /bits/ 64 <200000000>; + required-opps = <&rpmpd_opp_nom>; + opp-peak-kBps = <4096000 4096000>; + opp-avg-kBps = <1338562 1338562>; + }; + }; + }; + sdhc_1: sdhci@c0c4000 { compatible = "qcom,sdm630-sdhci", "qcom,sdhci-msm-v5"; reg = <0x0c0c4000 0x1000>, @@ -822,14 +1315,264 @@ <&gcc GCC_SDCC1_ICE_CORE_CLK>; clock-names = "core", "iface", "xo", "ice"; + interconnects = <&a2noc 2 &a2noc 10>, + <&gnoc 0 &cnoc 27>; + interconnect-names = "sdhc1-ddr", "cpu-sdhc1"; + operating-points-v2 = <&sdhc1_opp_table>; pinctrl-names = "default", "sleep"; - pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on &sdc1_rclk_on>; - pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off &sdc1_rclk_off>; + pinctrl-0 = <&sdc1_state_on>; + pinctrl-1 = <&sdc1_state_off>; + power-domains = <&rpmpd SDM660_VDDCX>; bus-width = <8>; non-removable; status = "disabled"; + + sdhc1_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-50000000 { + opp-hz = /bits/ 64 <50000000>; + required-opps = <&rpmpd_opp_low_svs>; + opp-peak-kBps = <200000 140000>; + opp-avg-kBps = <130718 133320>; + }; + opp-100000000 { + opp-hz = /bits/ 64 <100000000>; + required-opps = <&rpmpd_opp_svs>; + opp-peak-kBps = <250000 160000>; + opp-avg-kBps = <196078 150000>; + }; + opp-384000000 { + opp-hz = /bits/ 64 <384000000>; + required-opps = <&rpmpd_opp_nom>; + opp-peak-kBps = <4096000 4096000>; + opp-avg-kBps = <1338562 1338562>; + }; + }; + }; + + mmcc: clock-controller@c8c0000 { + compatible = "qcom,mmcc-sdm630"; + reg = <0x0c8c0000 0x40000>; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + clock-names = "xo", + "sleep_clk", + "gpll0", + "gpll0_div", + "dsi0pll", + "dsi0pllbyte", + "dsi1pll", + "dsi1pllbyte", + "dp_link_2x_clk_divsel_five", + "dp_vco_divided_clk_src_mux"; + clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>, + <&sleep_clk>, + <&gcc GCC_MMSS_GPLL0_CLK>, + <&gcc GCC_MMSS_GPLL0_DIV_CLK>, + <&dsi0_phy 1>, + <&dsi0_phy 0>, + <0>, + <0>, + <0>, + <0>; + }; + + dsi_opp_table: dsi-opp-table { + compatible = "operating-points-v2"; + + opp-131250000 { + opp-hz = /bits/ 64 <131250000>; + required-opps = <&rpmpd_opp_svs>; + }; + + opp-210000000 { + opp-hz = /bits/ 64 <210000000>; + required-opps = <&rpmpd_opp_svs_plus>; + }; + + opp-262500000 { + opp-hz = /bits/ 64 <262500000>; + required-opps = <&rpmpd_opp_nom>; + }; + }; + + mdss: mdss@c900000 { + compatible = "qcom,mdss"; + reg = <0x0c900000 0x1000>, + <0x0c9b0000 0x1040>; + reg-names = "mdss_phys", "vbif_phys"; + + power-domains = <&mmcc MDSS_GDSC>; + + clocks = <&mmcc MDSS_AHB_CLK>, + <&mmcc MDSS_AXI_CLK>, + <&mmcc MDSS_VSYNC_CLK>, + <&mmcc MDSS_MDP_CLK>; + clock-names = "iface", + "bus", + "vsync", + "core"; + + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + + interrupt-controller; + #interrupt-cells = <1>; + + #address-cells = <1>; + #size-cells = <1>; + ranges; + status = "disabled"; + + mdp: mdp@c901000 { + compatible = "qcom,mdp5"; + reg = <0x0c901000 0x89000>; + reg-names = "mdp_phys"; + + interrupt-parent = <&mdss>; + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; + + assigned-clocks = <&mmcc MDSS_MDP_CLK>, + <&mmcc MDSS_VSYNC_CLK>; + assigned-clock-rates = <300000000>, + <19200000>; + clocks = <&mmcc MDSS_AHB_CLK>, + <&mmcc MDSS_AXI_CLK>, + <&mmcc MDSS_MDP_CLK>, + <&mmcc MDSS_VSYNC_CLK>; + clock-names = "iface", + "bus", + "core", + "vsync"; + + interconnects = <&mnoc 2 &bimc 5>, + <&mnoc 3 &bimc 5>, + <&gnoc 0 &mnoc 17>; + interconnect-names = "mdp0-mem", + "mdp1-mem", + "rotator-mem"; + iommus = <&mmss_smmu 0>; + operating-points-v2 = <&mdp_opp_table>; + power-domains = <&rpmpd SDM660_VDDCX>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + mdp5_intf1_out: endpoint { + remote-endpoint = <&dsi0_in>; + }; + }; + }; + + mdp_opp_table: mdp-opp { + compatible = "operating-points-v2"; + + opp-150000000 { + opp-hz = /bits/ 64 <150000000>; + opp-peak-kBps = <320000 320000 76800>; + required-opps = <&rpmpd_opp_low_svs>; + }; + opp-275000000 { + opp-hz = /bits/ 64 <275000000>; + opp-peak-kBps = <6400000 6400000 160000>; + required-opps = <&rpmpd_opp_svs>; + }; + opp-300000000 { + opp-hz = /bits/ 64 <300000000>; + opp-peak-kBps = <6400000 6400000 190000>; + required-opps = <&rpmpd_opp_svs_plus>; + }; + opp-330000000 { + opp-hz = /bits/ 64 <330000000>; + opp-peak-kBps = <6400000 6400000 240000>; + required-opps = <&rpmpd_opp_nom>; + }; + opp-412500000 { + opp-hz = /bits/ 64 <412500000>; + opp-peak-kBps = <6400000 6400000 320000>; + required-opps = <&rpmpd_opp_turbo>; + }; + }; + }; + + dsi0: dsi@c994000 { + compatible = "qcom,mdss-dsi-ctrl"; + reg = <0x0c994000 0x400>; + reg-names = "dsi_ctrl"; + + operating-points-v2 = <&dsi_opp_table>; + power-domains = <&rpmpd SDM660_VDDCX>; + + interrupt-parent = <&mdss>; + interrupts = <4 IRQ_TYPE_LEVEL_HIGH>; + + assigned-clocks = <&mmcc BYTE0_CLK_SRC>, + <&mmcc PCLK0_CLK_SRC>; + assigned-clock-parents = <&dsi0_phy 0>, + <&dsi0_phy 1>; + + clocks = <&mmcc MDSS_MDP_CLK>, + <&mmcc MDSS_BYTE0_CLK>, + <&mmcc MDSS_BYTE0_INTF_CLK>, + <&mmcc MNOC_AHB_CLK>, + <&mmcc MDSS_AHB_CLK>, + <&mmcc MDSS_AXI_CLK>, + <&mmcc MISC_AHB_CLK>, + <&mmcc MDSS_PCLK0_CLK>, + <&mmcc MDSS_ESC0_CLK>; + clock-names = "mdp_core", + "byte", + "byte_intf", + "mnoc", + "iface", + "bus", + "core_mmss", + "pixel", + "core"; + + phys = <&dsi0_phy>; + phy-names = "dsi"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dsi0_in: endpoint { + remote-endpoint = <&mdp5_intf1_out>; + }; + }; + + port@1 { + reg = <1>; + dsi0_out: endpoint { + }; + }; + }; + }; + + dsi0_phy: dsi-phy@c994400 { + compatible = "qcom,dsi-phy-14nm-660"; + reg = <0x0c994400 0x100>, + <0x0c994500 0x300>, + <0x0c994800 0x188>; + reg-names = "dsi_phy", + "dsi_phy_lane", + "dsi_pll"; + + #clock-cells = <1>; + #phy-cells = <0>; + + clocks = <&mmcc MDSS_AHB_CLK>, <&xo_board>; + clock-names = "iface", "ref"; + }; }; blsp1_dma: dma-controller@c144000 { @@ -883,6 +1626,8 @@ <&gcc GCC_BLSP1_AHB_CLK>; clock-names = "core", "iface"; clock-frequency = <400000>; + dmas = <&blsp1_dma 4>, <&blsp1_dma 5>; + dma-names = "tx", "rx"; pinctrl-names = "default", "sleep"; pinctrl-0 = <&i2c1_default>; @@ -901,6 +1646,8 @@ <&gcc GCC_BLSP1_AHB_CLK>; clock-names = "core", "iface"; clock-frequency = <400000>; + dmas = <&blsp1_dma 6>, <&blsp1_dma 7>; + dma-names = "tx", "rx"; pinctrl-names = "default", "sleep"; pinctrl-0 = <&i2c2_default>; @@ -919,6 +1666,8 @@ <&gcc GCC_BLSP1_AHB_CLK>; clock-names = "core", "iface"; clock-frequency = <400000>; + dmas = <&blsp1_dma 8>, <&blsp1_dma 9>; + dma-names = "tx", "rx"; pinctrl-names = "default", "sleep"; pinctrl-0 = <&i2c3_default>; @@ -937,6 +1686,8 @@ <&gcc GCC_BLSP1_AHB_CLK>; clock-names = "core", "iface"; clock-frequency = <400000>; + dmas = <&blsp1_dma 10>, <&blsp1_dma 11>; + dma-names = "tx", "rx"; pinctrl-names = "default", "sleep"; pinctrl-0 = <&i2c4_default>; @@ -969,10 +1720,8 @@ dmas = <&blsp2_dma 0>, <&blsp2_dma 1>; dma-names = "tx", "rx"; pinctrl-names = "default", "sleep"; - pinctrl-0 = <&blsp2_uart1_tx_active &blsp2_uart1_rxcts_active - &blsp2_uart1_rfr_active>; - pinctrl-1 = <&blsp2_uart1_tx_sleep &blsp2_uart1_rxcts_sleep - &blsp2_uart1_rfr_sleep>; + pinctrl-0 = <&blsp2_uart1_default>; + pinctrl-1 = <&blsp2_uart1_sleep>; status = "disabled"; }; @@ -985,6 +1734,8 @@ <&gcc GCC_BLSP2_AHB_CLK>; clock-names = "core", "iface"; clock-frequency = <400000>; + dmas = <&blsp2_dma 4>, <&blsp2_dma 5>; + dma-names = "tx", "rx"; pinctrl-names = "default", "sleep"; pinctrl-0 = <&i2c5_default>; @@ -1003,6 +1754,8 @@ <&gcc GCC_BLSP2_AHB_CLK>; clock-names = "core", "iface"; clock-frequency = <400000>; + dmas = <&blsp2_dma 6>, <&blsp2_dma 7>; + dma-names = "tx", "rx"; pinctrl-names = "default", "sleep"; pinctrl-0 = <&i2c6_default>; @@ -1021,6 +1774,8 @@ <&gcc GCC_BLSP2_AHB_CLK>; clock-names = "core", "iface"; clock-frequency = <400000>; + dmas = <&blsp2_dma 8>, <&blsp2_dma 9>; + dma-names = "tx", "rx"; pinctrl-names = "default", "sleep"; pinctrl-0 = <&i2c7_default>; @@ -1039,6 +1794,8 @@ <&gcc GCC_BLSP2_AHB_CLK>; clock-names = "core", "iface"; clock-frequency = <400000>; + dmas = <&blsp2_dma 10>, <&blsp2_dma 11>; + dma-names = "tx", "rx"; pinctrl-names = "default", "sleep"; pinctrl-0 = <&i2c8_default>; @@ -1048,12 +1805,223 @@ status = "disabled"; }; + imem@146bf000 { + compatible = "simple-mfd"; + reg = <0x146bf000 0x1000>; + + #address-cells = <1>; + #size-cells = <1>; + + ranges = <0 0x146bf000 0x1000>; + + pil-reloc@94c { + compatible = "qcom,pil-reloc-info"; + reg = <0x94c 0xc8>; + }; + }; + + camss: camss@ca00000 { + compatible = "qcom,sdm660-camss"; + reg = <0x0c824000 0x1000>, + <0x0ca00120 0x4>, + <0x0c825000 0x1000>, + <0x0ca00124 0x4>, + <0x0c826000 0x1000>, + <0x0ca00128 0x4>, + <0x0ca30000 0x100>, + <0x0ca30400 0x100>, + <0x0ca30800 0x100>, + <0x0ca30c00 0x100>, + <0x0ca31000 0x500>, + <0x0ca00020 0x10>, + <0x0ca10000 0x1000>, + <0x0ca14000 0x1000>; + reg-names = "csiphy0", + "csiphy0_clk_mux", + "csiphy1", + "csiphy1_clk_mux", + "csiphy2", + "csiphy2_clk_mux", + "csid0", + "csid1", + "csid2", + "csid3", + "ispif", + "csi_clk_mux", + "vfe0", + "vfe1"; + interrupts = <GIC_SPI 78 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 79 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 80 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 296 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 297 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 298 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 299 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 309 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 314 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 315 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "csiphy0", + "csiphy1", + "csiphy2", + "csid0", + "csid1", + "csid2", + "csid3", + "ispif", + "vfe0", + "vfe1"; + clocks = <&mmcc CAMSS_TOP_AHB_CLK>, + <&mmcc THROTTLE_CAMSS_AXI_CLK>, + <&mmcc CAMSS_ISPIF_AHB_CLK>, + <&mmcc CAMSS_CSI0PHYTIMER_CLK>, + <&mmcc CAMSS_CSI1PHYTIMER_CLK>, + <&mmcc CAMSS_CSI2PHYTIMER_CLK>, + <&mmcc CAMSS_CSI0_AHB_CLK>, + <&mmcc CAMSS_CSI0_CLK>, + <&mmcc CAMSS_CPHY_CSID0_CLK>, + <&mmcc CAMSS_CSI0PIX_CLK>, + <&mmcc CAMSS_CSI0RDI_CLK>, + <&mmcc CAMSS_CSI1_AHB_CLK>, + <&mmcc CAMSS_CSI1_CLK>, + <&mmcc CAMSS_CPHY_CSID1_CLK>, + <&mmcc CAMSS_CSI1PIX_CLK>, + <&mmcc CAMSS_CSI1RDI_CLK>, + <&mmcc CAMSS_CSI2_AHB_CLK>, + <&mmcc CAMSS_CSI2_CLK>, + <&mmcc CAMSS_CPHY_CSID2_CLK>, + <&mmcc CAMSS_CSI2PIX_CLK>, + <&mmcc CAMSS_CSI2RDI_CLK>, + <&mmcc CAMSS_CSI3_AHB_CLK>, + <&mmcc CAMSS_CSI3_CLK>, + <&mmcc CAMSS_CPHY_CSID3_CLK>, + <&mmcc CAMSS_CSI3PIX_CLK>, + <&mmcc CAMSS_CSI3RDI_CLK>, + <&mmcc CAMSS_AHB_CLK>, + <&mmcc CAMSS_VFE0_CLK>, + <&mmcc CAMSS_CSI_VFE0_CLK>, + <&mmcc CAMSS_VFE0_AHB_CLK>, + <&mmcc CAMSS_VFE0_STREAM_CLK>, + <&mmcc CAMSS_VFE1_CLK>, + <&mmcc CAMSS_CSI_VFE1_CLK>, + <&mmcc CAMSS_VFE1_AHB_CLK>, + <&mmcc CAMSS_VFE1_STREAM_CLK>, + <&mmcc CAMSS_VFE_VBIF_AHB_CLK>, + <&mmcc CAMSS_VFE_VBIF_AXI_CLK>, + <&mmcc CSIPHY_AHB2CRIF_CLK>, + <&mmcc CAMSS_CPHY_CSID0_CLK>, + <&mmcc CAMSS_CPHY_CSID1_CLK>, + <&mmcc CAMSS_CPHY_CSID2_CLK>, + <&mmcc CAMSS_CPHY_CSID3_CLK>; + clock-names = "top_ahb", + "throttle_axi", + "ispif_ahb", + "csiphy0_timer", + "csiphy1_timer", + "csiphy2_timer", + "csi0_ahb", + "csi0", + "csi0_phy", + "csi0_pix", + "csi0_rdi", + "csi1_ahb", + "csi1", + "csi1_phy", + "csi1_pix", + "csi1_rdi", + "csi2_ahb", + "csi2", + "csi2_phy", + "csi2_pix", + "csi2_rdi", + "csi3_ahb", + "csi3", + "csi3_phy", + "csi3_pix", + "csi3_rdi", + "ahb", + "vfe0", + "csi_vfe0", + "vfe0_ahb", + "vfe0_stream", + "vfe1", + "csi_vfe1", + "vfe1_ahb", + "vfe1_stream", + "vfe_ahb", + "vfe_axi", + "csiphy_ahb2crif", + "cphy_csid0", + "cphy_csid1", + "cphy_csid2", + "cphy_csid3"; + interconnects = <&mnoc 5 &bimc 5>; + interconnect-names = "vfe-mem"; + iommus = <&mmss_smmu 0xc00>, + <&mmss_smmu 0xc01>, + <&mmss_smmu 0xc02>, + <&mmss_smmu 0xc03>; + power-domains = <&mmcc CAMSS_VFE0_GDSC>, + <&mmcc CAMSS_VFE1_GDSC>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + cci: cci@ca0c000 { + compatible = "qcom,msm8996-cci"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0ca0c000 0x1000>; + interrupts = <GIC_SPI 295 IRQ_TYPE_EDGE_RISING>; + + assigned-clocks = <&mmcc CAMSS_CCI_AHB_CLK>, + <&mmcc CAMSS_CCI_CLK>; + assigned-clock-rates = <80800000>, <37500000>; + clocks = <&mmcc CAMSS_TOP_AHB_CLK>, + <&mmcc CAMSS_CCI_AHB_CLK>, + <&mmcc CAMSS_CCI_CLK>, + <&mmcc CAMSS_AHB_CLK>; + clock-names = "camss_top_ahb", + "cci_ahb", + "cci", + "camss_ahb"; + + pinctrl-names = "default"; + pinctrl-0 = <&cci0_default &cci1_default>; + power-domains = <&mmcc CAMSS_TOP_GDSC>; + status = "disabled"; + + cci_i2c0: i2c-bus@0 { + reg = <0>; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; + }; + + cci_i2c1: i2c-bus@1 { + reg = <1>; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; + }; + }; + mmss_smmu: iommu@cd00000 { compatible = "qcom,sdm630-smmu-v2", "qcom,smmu-v2"; reg = <0x0cd00000 0x40000>; - #iommu-cells = <1>; + clocks = <&mmcc MNOC_AHB_CLK>, + <&mmcc BIMC_SMMU_AHB_CLK>, + <&rpmcc RPM_SMD_MMSSNOC_AXI_CLK>, + <&mmcc BIMC_SMMU_AXI_CLK>; + clock-names = "iface-mm", "iface-smmu", + "bus-mm", "bus-smmu"; #global-interrupts = <2>; + #iommu-cells = <1>; + interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>, @@ -1086,6 +2054,97 @@ status = "disabled"; }; + adsp_pil: remoteproc@15700000 { + compatible = "qcom,sdm660-adsp-pas"; + reg = <0x15700000 0x4040>; + + interrupts-extended = + <&intc GIC_SPI 162 IRQ_TYPE_EDGE_RISING>, + <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, + <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>, + <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>, + <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "wdog", "fatal", "ready", + "handover", "stop-ack"; + + clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>; + clock-names = "xo"; + + memory-region = <&adsp_region>; + power-domains = <&rpmpd SDM660_VDDCX>; + power-domain-names = "cx"; + + qcom,smem-states = <&adsp_smp2p_out 0>; + qcom,smem-state-names = "stop"; + + glink-edge { + interrupts = <GIC_SPI 157 IRQ_TYPE_EDGE_RISING>; + + label = "lpass"; + mboxes = <&apcs_glb 9>; + qcom,remote-pid = <2>; + #address-cells = <1>; + #size-cells = <0>; + + apr { + compatible = "qcom,apr-v2"; + qcom,glink-channels = "apr_audio_svc"; + qcom,apr-domain = <APR_DOMAIN_ADSP>; + #address-cells = <1>; + #size-cells = <0>; + + q6core { + reg = <APR_SVC_ADSP_CORE>; + compatible = "qcom,q6core"; + }; + + q6afe: apr-service@4 { + compatible = "qcom,q6afe"; + reg = <APR_SVC_AFE>; + q6afedai: dais { + compatible = "qcom,q6afe-dais"; + #address-cells = <1>; + #size-cells = <0>; + #sound-dai-cells = <1>; + }; + }; + + q6asm: apr-service@7 { + compatible = "qcom,q6asm"; + reg = <APR_SVC_ASM>; + q6asmdai: dais { + compatible = "qcom,q6asm-dais"; + #address-cells = <1>; + #size-cells = <0>; + #sound-dai-cells = <1>; + iommus = <&lpass_smmu 1>; + }; + }; + + q6adm: apr-service@8 { + compatible = "qcom,q6adm"; + reg = <APR_SVC_ADM>; + q6routing: routing { + compatible = "qcom,q6adm-routing"; + #sound-dai-cells = <0>; + }; + }; + }; + }; + }; + + gnoc: interconnect@17900000 { + compatible = "qcom,sdm660-gnoc"; + reg = <0x17900000 0xe000>; + #interconnect-cells = <1>; + /* + * This one apparently features no clocks, + * so let's not mess with the driver needlessly + */ + clock-names = "bus", "bus_a"; + clocks = <&xo_board>, <&xo_board>; + }; + apcs_glb: mailbox@17911000 { compatible = "qcom,sdm660-apcs-hmss-global"; reg = <0x17911000 0x1000>; @@ -1173,6 +2232,182 @@ #hwlock-cells = <1>; }; + sound: sound { + }; + + thermal-zones { + aoss-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 0>; + + trips { + aoss_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <1000>; + type = "hot"; + }; + }; + }; + + cpuss0-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 1>; + + trips { + cpuss0_alert0: trip-point0 { + temperature = <125000>; + hysteresis = <1000>; + type = "hot"; + }; + }; + }; + + cpuss1-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 2>; + + trips { + cpuss1_alert0: trip-point0 { + temperature = <125000>; + hysteresis = <1000>; + type = "hot"; + }; + }; + }; + + cpu0-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 3>; + + trips { + cpu0_alert0: trip-point0 { + temperature = <70000>; + hysteresis = <1000>; + type = "passive"; + }; + + cpu0_crit: cpu_crit { + temperature = <110000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + }; + + cpu1-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 4>; + + trips { + cpu1_alert0: trip-point0 { + temperature = <70000>; + hysteresis = <1000>; + type = "passive"; + }; + + cpu1_crit: cpu_crit { + temperature = <110000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + }; + + cpu2-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 5>; + + trips { + cpu2_alert0: trip-point0 { + temperature = <70000>; + hysteresis = <1000>; + type = "passive"; + }; + + cpu2_crit: cpu_crit { + temperature = <110000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + }; + + cpu3-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 6>; + + trips { + cpu3_alert0: trip-point0 { + temperature = <70000>; + hysteresis = <1000>; + type = "passive"; + }; + + cpu3_crit: cpu_crit { + temperature = <110000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + }; + + /* + * According to what downstream DTS says, + * the entire power efficient cluster has + * only a single thermal sensor. + */ + + pwr-cluster-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 7>; + + trips { + pwr_cluster_alert0: trip-point0 { + temperature = <70000>; + hysteresis = <1000>; + type = "passive"; + }; + + pwr_cluster_crit: cpu_crit { + temperature = <110000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + }; + + gpu-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 8>; + + trips { + gpu_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <1000>; + type = "hot"; + }; + }; + }; + }; + timer { compatible = "arm,armv8-timer"; interrupts = <GIC_PPI 1 0xf08>, diff --git a/dts/src/arm64/qcom/sdm636-sony-xperia-ganges-mermaid.dts b/dts/src/arm64/qcom/sdm636-sony-xperia-ganges-mermaid.dts index 7c0830e6a4..bba1c2bce2 100644 --- a/dts/src/arm64/qcom/sdm636-sony-xperia-ganges-mermaid.dts +++ b/dts/src/arm64/qcom/sdm636-sony-xperia-ganges-mermaid.dts @@ -5,16 +5,20 @@ /dts-v1/; -/* Mermaid uses sdm636, but it's different ever so slightly - * that we can ignore it for the time being. Sony also commonizes - * the Ganges platform as a whole in downstream kernels. - */ -#include "sdm630-sony-xperia-ganges.dtsi" +#include "sdm630-sony-xperia-ganges-kirin.dts" +#include "sdm636.dtsi" / { model = "Sony Xperia 10 Plus"; compatible = "sony,mermaid-row", "qcom,sdm636"; + /* SDM636 v1 */ qcom,msm-id = <345 0>; qcom,pmic-id = <0x1001b 0x101011a 0x00 0x00 0x1001b 0x201011a 0x00 0x00 0x1001b 0x102001a 0x00 0x00>; }; + +&sdc2_state_on { + pinconf-clk { + drive-strength = <14>; + }; +}; diff --git a/dts/src/arm64/qcom/sdm636.dtsi b/dts/src/arm64/qcom/sdm636.dtsi new file mode 100644 index 0000000000..ae15d81fa3 --- /dev/null +++ b/dts/src/arm64/qcom/sdm636.dtsi @@ -0,0 +1,23 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2020, AngeloGioacchino Del Regno <kholk11@gmail.com> + * Copyright (c) 2020, Konrad Dybcio <konradybcio@gmail.com> + * Copyright (c) 2020, Martin Botka <martin.botka1@gmail.com> + */ + +#include "sdm660.dtsi" + +/* + * According to the downstream DTS, + * 636 is basically a 660 except for + * different CPU frequencies, Adreno + * 509 instead of 512 and lack of + * turing IP. These differences will + * be addressed when the aforementioned + * peripherals will be enabled upstream. + */ + +&adreno_gpu { + compatible = "qcom,adreno-509.0", "qcom,adreno"; + /* Adreno 509 shares the frequency table with 512 */ +}; diff --git a/dts/src/arm64/qcom/sdm660-xiaomi-lavender.dts b/dts/src/arm64/qcom/sdm660-xiaomi-lavender.dts index 76533e8b20..3e677fb7cf 100644 --- a/dts/src/arm64/qcom/sdm660-xiaomi-lavender.dts +++ b/dts/src/arm64/qcom/sdm660-xiaomi-lavender.dts @@ -37,8 +37,6 @@ &blsp1_uart2 { status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&uart_console_active>; }; &tlmm { diff --git a/dts/src/arm64/qcom/sdm660.dtsi b/dts/src/arm64/qcom/sdm660.dtsi index 4abbdd03d1..eccf6fde16 100644 --- a/dts/src/arm64/qcom/sdm660.dtsi +++ b/dts/src/arm64/qcom/sdm660.dtsi @@ -2,371 +2,250 @@ /* * Copyright (c) 2018, Craig Tatlor. * Copyright (c) 2020, Alexey Minnekhanov <alexey.min@gmail.com> + * Copyright (c) 2020, AngeloGioacchino Del Regno <kholk11@gmail.com> + * Copyright (c) 2020, Konrad Dybcio <konradybcio@gmail.com> + * Copyright (c) 2020, Martin Botka <martin.botka1@gmail.com> */ -#include <dt-bindings/interrupt-controller/arm-gic.h> -#include <dt-bindings/clock/qcom,gcc-sdm660.h> +#include "sdm630.dtsi" -/ { - interrupt-parent = <&intc>; +&adreno_gpu { + compatible = "qcom,adreno-512.0", "qcom,adreno"; + operating-points-v2 = <&gpu_sdm660_opp_table>; - #address-cells = <2>; - #size-cells = <2>; + gpu_sdm660_opp_table: opp-table { + compatible = "operating-points-v2"; - chosen { }; + /* + * 775MHz is only available on the highest speed bin + * Though it cannot be used for now due to interconnect + * framework not supporting multiple frequencies + * at the same opp-level - clocks { - xo_board: xo_board { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <19200000>; - clock-output-names = "xo_board"; + opp-750000000 { + opp-hz = /bits/ 64 <750000000>; + opp-level = <RPM_SMD_LEVEL_TURBO>; + opp-peak-kBps = <5412000>; + opp-supported-hw = <0xCHECKME>; }; - sleep_clk: sleep_clk { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <32764>; - clock-output-names = "sleep_clk"; - }; - }; + * These OPPs are correct, but we are lacking support for the + * GPU regulator. Hence, disable them for now to prevent the + * platform from hanging on high graphics loads. - cpus { - #address-cells = <2>; - #size-cells = <0>; - - CPU0: cpu@100 { - device_type = "cpu"; - compatible = "qcom,kryo260"; - reg = <0x0 0x100>; - enable-method = "psci"; - capacity-dmips-mhz = <1024>; - next-level-cache = <&L2_1>; - L2_1: l2-cache { - compatible = "cache"; - cache-level = <2>; - }; - L1_I_100: l1-icache { - compatible = "cache"; - }; - L1_D_100: l1-dcache { - compatible = "cache"; - }; + opp-700000000 { + opp-hz = /bits/ 64 <700000000>; + opp-level = <RPM_SMD_LEVEL_TURBO>; + opp-peak-kBps = <5184000>; + opp-supported-hw = <0xFF>; }; - CPU1: cpu@101 { - device_type = "cpu"; - compatible = "qcom,kryo260"; - reg = <0x0 0x101>; - enable-method = "psci"; - capacity-dmips-mhz = <1024>; - next-level-cache = <&L2_1>; - L1_I_101: l1-icache { - compatible = "cache"; - }; - L1_D_101: l1-dcache { - compatible = "cache"; - }; + opp-647000000 { + opp-hz = /bits/ 64 <647000000>; + opp-level = <RPM_SMD_LEVEL_NOM_PLUS>; + opp-peak-kBps = <4068000>; + opp-supported-hw = <0xFF>; }; - CPU2: cpu@102 { - device_type = "cpu"; - compatible = "qcom,kryo260"; - reg = <0x0 0x102>; - enable-method = "psci"; - capacity-dmips-mhz = <1024>; - next-level-cache = <&L2_1>; - L1_I_102: l1-icache { - compatible = "cache"; - }; - L1_D_102: l1-dcache { - compatible = "cache"; - }; + opp-588000000 { + opp-hz = /bits/ 64 <588000000>; + opp-level = <RPM_SMD_LEVEL_NOM>; + opp-peak-kBps = <3072000>; + opp-supported-hw = <0xFF>; }; - CPU3: cpu@103 { - device_type = "cpu"; - compatible = "qcom,kryo260"; - reg = <0x0 0x103>; - enable-method = "psci"; - capacity-dmips-mhz = <1024>; - next-level-cache = <&L2_1>; - L1_I_103: l1-icache { - compatible = "cache"; - }; - L1_D_103: l1-dcache { - compatible = "cache"; - }; + opp-465000000 { + opp-hz = /bits/ 64 <465000000>; + opp-level = <RPM_SMD_LEVEL_SVS_PLUS>; + opp-peak-kBps = <2724000>; + opp-supported-hw = <0xFF>; }; - CPU4: cpu@0 { - device_type = "cpu"; - compatible = "qcom,kryo260"; - reg = <0x0 0x0>; - enable-method = "psci"; - capacity-dmips-mhz = <640>; - next-level-cache = <&L2_0>; - L2_0: l2-cache { - compatible = "cache"; - cache-level = <2>; - }; - L1_I_0: l1-icache { - compatible = "cache"; - }; - L1_D_0: l1-dcache { - compatible = "cache"; - }; + opp-370000000 { + opp-hz = /bits/ 64 <370000000>; + opp-level = <RPM_SMD_LEVEL_SVS>; + opp-peak-kBps = <2188000>; + opp-supported-hw = <0xFF>; }; + */ - CPU5: cpu@1 { - device_type = "cpu"; - compatible = "qcom,kryo260"; - reg = <0x0 0x1>; - enable-method = "psci"; - capacity-dmips-mhz = <640>; - next-level-cache = <&L2_0>; - L1_I_1: l1-icache { - compatible = "cache"; - }; - L1_D_1: l1-dcache { - compatible = "cache"; - }; + opp-266000000 { + opp-hz = /bits/ 64 <266000000>; + opp-level = <RPM_SMD_LEVEL_LOW_SVS>; + opp-peak-kBps = <1648000>; + opp-supported-hw = <0xFF>; }; - CPU6: cpu@2 { - device_type = "cpu"; - compatible = "qcom,kryo260"; - reg = <0x0 0x2>; - enable-method = "psci"; - capacity-dmips-mhz = <640>; - next-level-cache = <&L2_0>; - L1_I_2: l1-icache { - compatible = "cache"; - }; - L1_D_2: l1-dcache { - compatible = "cache"; - }; + opp-160000000 { + opp-hz = /bits/ 64 <160000000>; + opp-level = <RPM_SMD_LEVEL_MIN_SVS>; + opp-peak-kBps = <1200000>; + opp-supported-hw = <0xFF>; }; + }; +}; - CPU7: cpu@3 { - device_type = "cpu"; - compatible = "qcom,kryo260"; - reg = <0x0 0x3>; - enable-method = "psci"; - capacity-dmips-mhz = <640>; - next-level-cache = <&L2_0>; - L1_I_3: l1-icache { - compatible = "cache"; - }; - L1_D_3: l1-dcache { - compatible = "cache"; - }; - }; - - cpu-map { - cluster0 { - core0 { - cpu = <&CPU4>; - }; - - core1 { - cpu = <&CPU5>; - }; - - core2 { - cpu = <&CPU6>; - }; - - core3 { - cpu = <&CPU7>; - }; - }; - - cluster1 { - core0 { - cpu = <&CPU0>; - }; +&CPU0 { + compatible = "qcom,kryo260"; + capacity-dmips-mhz = <1024>; + /delete-property/ operating-points-v2; +}; - core1 { - cpu = <&CPU1>; - }; +&CPU1 { + compatible = "qcom,kryo260"; + capacity-dmips-mhz = <1024>; + /delete-property/ operating-points-v2; +}; - core2 { - cpu = <&CPU2>; - }; +&CPU2 { + compatible = "qcom,kryo260"; + capacity-dmips-mhz = <1024>; + /delete-property/ operating-points-v2; +}; - core3 { - cpu = <&CPU3>; - }; - }; - }; - }; +&CPU3 { + compatible = "qcom,kryo260"; + capacity-dmips-mhz = <1024>; + /delete-property/ operating-points-v2; +}; - firmware { - scm { - compatible = "qcom,scm"; - }; - }; +&CPU4 { + compatible = "qcom,kryo260"; + capacity-dmips-mhz = <640>; + /delete-property/ operating-points-v2; +}; - memory { - device_type = "memory"; - /* We expect the bootloader to fill in the reg */ - reg = <0 0 0 0>; - }; +&CPU5 { + compatible = "qcom,kryo260"; + capacity-dmips-mhz = <640>; + /delete-property/ operating-points-v2; +}; - psci { - compatible = "arm,psci-1.0"; - method = "smc"; - }; +&CPU6 { + compatible = "qcom,kryo260"; + capacity-dmips-mhz = <640>; + /delete-property/ operating-points-v2; +}; - timer { - compatible = "arm,armv8-timer"; - interrupts = <GIC_PPI 1 IRQ_TYPE_LEVEL_LOW>, - <GIC_PPI 2 IRQ_TYPE_LEVEL_LOW>, - <GIC_PPI 3 IRQ_TYPE_LEVEL_LOW>, - <GIC_PPI 0 IRQ_TYPE_LEVEL_LOW>; - }; +&CPU7 { + compatible = "qcom,kryo260"; + capacity-dmips-mhz = <640>; + /delete-property/ operating-points-v2; +}; - soc: soc { - #address-cells = <1>; - #size-cells = <1>; - ranges = <0 0 0 0xffffffff>; - compatible = "simple-bus"; - - gcc: clock-controller@100000 { - compatible = "qcom,gcc-sdm660"; - #clock-cells = <1>; - #reset-cells = <1>; - #power-domain-cells = <1>; - reg = <0x00100000 0x94000>; - }; +&gcc { + compatible = "qcom,gcc-sdm660"; +}; - tlmm: pinctrl@3100000 { - compatible = "qcom,sdm660-pinctrl"; - reg = <0x03100000 0x400000>, - <0x03500000 0x400000>, - <0x03900000 0x400000>; - reg-names = "south", "center", "north"; - interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; - gpio-controller; - gpio-ranges = <&tlmm 0 0 114>; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - - uart_console_active: uart_console_active { - pinmux { - pins = "gpio4", "gpio5"; - function = "blsp_uart2"; - }; +&gpucc { + compatible = "qcom,gpucc-sdm660"; +}; - pinconf { - pins = "gpio4", "gpio5"; - drive-strength = <2>; - bias-disable; - }; +&mdp { + ports { + port@1 { + reg = <1>; + mdp5_intf2_out: endpoint { + remote-endpoint = <&dsi1_in>; }; }; + }; +}; - spmi_bus: spmi@800f000 { - compatible = "qcom,spmi-pmic-arb"; - reg = <0x0800f000 0x1000>, - <0x08400000 0x1000000>, - <0x09400000 0x1000000>, - <0x0a400000 0x220000>, - <0x0800a000 0x3000>; - reg-names = "core", "chnls", "obsrvr", "intr", "cnfg"; - interrupt-names = "periph_irq"; - interrupts = <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>; - qcom,ee = <0>; - qcom,channel = <0>; - #address-cells = <2>; +&mdss { + dsi1: dsi@c996000 { + compatible = "qcom,mdss-dsi-ctrl"; + reg = <0x0c996000 0x400>; + reg-names = "dsi_ctrl"; + + /* DSI1 shares the OPP table with DSI0 */ + operating-points-v2 = <&dsi_opp_table>; + power-domains = <&rpmpd SDM660_VDDCX>; + + interrupt-parent = <&mdss>; + interrupts = <5 IRQ_TYPE_LEVEL_HIGH>; + + assigned-clocks = <&mmcc BYTE1_CLK_SRC>, + <&mmcc PCLK1_CLK_SRC>; + assigned-clock-parents = <&dsi1_phy 0>, + <&dsi1_phy 1>; + + clocks = <&mmcc MDSS_MDP_CLK>, + <&mmcc MDSS_BYTE1_CLK>, + <&mmcc MDSS_BYTE1_INTF_CLK>, + <&mmcc MNOC_AHB_CLK>, + <&mmcc MDSS_AHB_CLK>, + <&mmcc MDSS_AXI_CLK>, + <&mmcc MISC_AHB_CLK>, + <&mmcc MDSS_PCLK1_CLK>, + <&mmcc MDSS_ESC1_CLK>; + clock-names = "mdp_core", + "byte", + "byte_intf", + "mnoc", + "iface", + "bus", + "core_mmss", + "pixel", + "core"; + + phys = <&dsi1_phy>; + phy-names = "dsi"; + + ports { + #address-cells = <1>; #size-cells = <0>; - interrupt-controller; - #interrupt-cells = <4>; - cell-index = <0>; - }; - blsp1_uart2: serial@c170000 { - compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; - reg = <0x0c170000 0x1000>; - interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, - <&gcc GCC_BLSP1_AHB_CLK>; - clock-names = "core", "iface"; - status = "disabled"; - }; - - timer@17920000 { - #address-cells = <1>; - #size-cells = <1>; - ranges; - compatible = "arm,armv7-timer-mem"; - reg = <0x17920000 0x1000>; - - frame@17921000 { - frame-number = <0>; - interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; - reg = <0x17921000 0x1000>, - <0x17922000 0x1000>; + port@0 { + reg = <0>; + dsi1_in: endpoint { + remote-endpoint = <&mdp5_intf2_out>; + }; }; - frame@17923000 { - frame-number = <1>; - interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; - reg = <0x17923000 0x1000>; - status = "disabled"; + port@1 { + reg = <1>; + dsi1_out: endpoint { + }; }; + }; + }; - frame@17924000 { - frame-number = <2>; - interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; - reg = <0x17924000 0x1000>; - status = "disabled"; - }; + dsi1_phy: dsi-phy@c996400 { + compatible = "qcom,dsi-phy-14nm-660"; + reg = <0x0c996400 0x100>, + <0x0c996500 0x300>, + <0x0c996800 0x188>; + reg-names = "dsi_phy", + "dsi_phy_lane", + "dsi_pll"; - frame@17925000 { - frame-number = <3>; - interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; - reg = <0x17925000 0x1000>; - status = "disabled"; - }; + #clock-cells = <1>; + #phy-cells = <0>; - frame@17926000 { - frame-number = <4>; - interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; - reg = <0x17926000 0x1000>; - status = "disabled"; - }; + clocks = <&mmcc MDSS_AHB_CLK>, <&rpmcc RPM_SMD_XO_CLK_SRC>; + clock-names = "iface", "ref"; + }; +}; - frame@17927000 { - frame-number = <5>; - interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; - reg = <0x17927000 0x1000>; - status = "disabled"; - }; +&mmcc { + compatible = "qcom,mmcc-sdm660"; + clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>, + <&sleep_clk>, + <&gcc GCC_MMSS_GPLL0_CLK>, + <&gcc GCC_MMSS_GPLL0_DIV_CLK>, + <&dsi0_phy 1>, + <&dsi0_phy 0>, + <&dsi1_phy 1>, + <&dsi1_phy 0>, + <0>, + <0>; +}; - frame@17928000 { - frame-number = <6>; - interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; - reg = <0x17928000 0x1000>; - status = "disabled"; - }; - }; +&tlmm { + compatible = "qcom,sdm660-pinctrl"; +}; - intc: interrupt-controller@17a00000 { - compatible = "arm,gic-v3"; - reg = <0x17a00000 0x10000>, - <0x17b00000 0x100000>; - #interrupt-cells = <3>; - #address-cells = <1>; - #size-cells = <1>; - ranges; - interrupt-controller; - #redistributor-regions = <1>; - redistributor-stride = <0x0 0x20000>; - interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; - }; - }; +&tsens { + #qcom,sensors = <14>; }; diff --git a/dts/src/arm64/qcom/sdm845-mtp.dts b/dts/src/arm64/qcom/sdm845-mtp.dts index 91ede9296a..52dd7a8582 100644 --- a/dts/src/arm64/qcom/sdm845-mtp.dts +++ b/dts/src/arm64/qcom/sdm845-mtp.dts @@ -413,6 +413,9 @@ qcom,dual-dsi-mode; + /* DSI1 is slave, so use DSI0 clocks */ + assigned-clock-parents = <&dsi0_phy 0>, <&dsi0_phy 1>; + ports { port@1 { endpoint { diff --git a/dts/src/arm64/qcom/sdm845-oneplus-common.dtsi b/dts/src/arm64/qcom/sdm845-oneplus-common.dtsi index eb6b1d1529..d435552237 100644 --- a/dts/src/arm64/qcom/sdm845-oneplus-common.dtsi +++ b/dts/src/arm64/qcom/sdm845-oneplus-common.dtsi @@ -19,9 +19,14 @@ / { aliases { + serial0 = &uart9; hsuart0 = &uart6; }; + chosen { + stdout-path = "serial0:115200n8"; + }; + gpio-keys { compatible = "gpio-keys"; label = "Volume keys"; @@ -403,6 +408,7 @@ status = "okay"; memory-region = <&ipa_fw_mem>; + firmware-name = "qcom/sdm845/oneplus6/ipa_fws.mbn"; }; &mdss { @@ -526,6 +532,11 @@ }; }; +&uart9 { + label = "LS-UART1"; + status = "okay"; +}; + &ufs_mem_hc { status = "okay"; diff --git a/dts/src/arm64/qcom/sdm845.dtsi b/dts/src/arm64/qcom/sdm845.dtsi index 0a86fe71a6..6d7172e6f4 100644 --- a/dts/src/arm64/qcom/sdm845.dtsi +++ b/dts/src/arm64/qcom/sdm845.dtsi @@ -128,28 +128,23 @@ no-map; }; - ipa_fw_mem: memory@8c400000 { - reg = <0 0x8c400000 0 0x10000>; + wlan_msa_mem: memory@8c400000 { + reg = <0 0x8c400000 0 0x100000>; no-map; }; - ipa_gsi_mem: memory@8c410000 { - reg = <0 0x8c410000 0 0x5000>; + gpu_mem: memory@8c515000 { + reg = <0 0x8c515000 0 0x2000>; no-map; }; - gpu_mem: memory@8c415000 { - reg = <0 0x8c415000 0 0x2000>; + ipa_fw_mem: memory@8c517000 { + reg = <0 0x8c517000 0 0x5a000>; no-map; }; - adsp_mem: memory@8c500000 { - reg = <0 0x8c500000 0 0x1a00000>; - no-map; - }; - - wlan_msa_mem: memory@8df00000 { - reg = <0 0x8df00000 0 0x100000>; + adsp_mem: memory@8c600000 { + reg = <0 0x8c600000 0 0x1a00000>; no-map; }; @@ -4148,9 +4143,8 @@ power-domains = <&dispcc MDSS_GDSC>; clocks = <&gcc GCC_DISP_AHB_CLK>, - <&gcc GCC_DISP_AXI_CLK>, <&dispcc DISP_CC_MDSS_MDP_CLK>; - clock-names = "iface", "bus", "core"; + clock-names = "iface", "core"; assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>; assigned-clock-rates = <300000000>; @@ -4178,11 +4172,12 @@ <0 0x0aeb0000 0 0x2008>; reg-names = "mdp", "vbif"; - clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, + clocks = <&gcc GCC_DISP_AXI_CLK>, + <&dispcc DISP_CC_MDSS_AHB_CLK>, <&dispcc DISP_CC_MDSS_AXI_CLK>, <&dispcc DISP_CC_MDSS_MDP_CLK>, <&dispcc DISP_CC_MDSS_VSYNC_CLK>; - clock-names = "iface", "bus", "core", "vsync"; + clock-names = "gcc-bus", "iface", "bus", "core", "vsync"; assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>, <&dispcc DISP_CC_MDSS_VSYNC_CLK>; @@ -4260,6 +4255,9 @@ "core", "iface", "bus"; + assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>; + assigned-clock-parents = <&dsi0_phy 0>, <&dsi0_phy 1>; + operating-points-v2 = <&dsi_opp_table>; power-domains = <&rpmhpd SDM845_CX>; @@ -4326,6 +4324,9 @@ "core", "iface", "bus"; + assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK1_CLK_SRC>; + assigned-clock-parents = <&dsi1_phy 0>, <&dsi1_phy 1>; + operating-points-v2 = <&dsi_opp_table>; power-domains = <&rpmhpd SDM845_CX>; diff --git a/dts/src/arm64/qcom/sdm850-lenovo-yoga-c630.dts b/dts/src/arm64/qcom/sdm850-lenovo-yoga-c630.dts index d7591a4621..385e502943 100644 --- a/dts/src/arm64/qcom/sdm850-lenovo-yoga-c630.dts +++ b/dts/src/arm64/qcom/sdm850-lenovo-yoga-c630.dts @@ -415,6 +415,11 @@ }; }; +&ipa { + status = "okay"; + memory-region = <&ipa_fw_mem>; +}; + &mdss { status = "okay"; }; diff --git a/dts/src/arm64/qcom/sm6125-sony-xperia-seine-pdx201.dts b/dts/src/arm64/qcom/sm6125-sony-xperia-seine-pdx201.dts new file mode 100644 index 0000000000..58b6b2742d --- /dev/null +++ b/dts/src/arm64/qcom/sm6125-sony-xperia-seine-pdx201.dts @@ -0,0 +1,139 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2021, Martin Botka <martin.botka@somainline.org> + */ + +/dts-v1/; + +#include "sm6125.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/input/gpio-keys.h> + +/ { + /* required for bootloader to select correct board */ + qcom,msm-id = <394 0x10000>; /* sm6125 v1 */ + qcom,board-id = <34 0>; + + model = "Sony Xperia 10 II"; + compatible = "sony,pdx201", "qcom,sm6125"; + + chosen { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + framebuffer0: framebuffer@5c000000 { + compatible = "simple-framebuffer"; + reg = <0 0x5c000000 0 (2520 * 1080 * 4)>; + width = <1080>; + height = <2520>; + stride = <(1080 * 4)>; + format = "a8r8g8b8"; + }; + }; + + extcon_usb: extcon-usb { + compatible = "linux,extcon-usb-gpio"; + id-gpio = <&tlmm 102 GPIO_ACTIVE_HIGH>; + }; + + gpio-keys { + status = "okay"; + compatible = "gpio-keys"; + input-name = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + autorepeat; + + vol-dn { + label = "Volume Down"; + gpios = <&tlmm 47 GPIO_ACTIVE_LOW>; + linux,input-type = <1>; + linux,code = <KEY_VOLUMEDOWN>; + gpio-key,wakeup; + debounce-interval = <15>; + }; + }; + + reserved_memory { + #address-cells = <2>; + #size-cells = <2>; + debug_mem: memory@ffb00000 { + reg = <0x0 0xffb00000 0x0 0xc0000>; + no-map; + }; + + last_log_mem: memory@ffbc0000 { + reg = <0x0 0xffbc0000 0x0 0x80000>; + no-map; + }; + + pstore_mem: ramoops@ffc00000 { + compatible = "ramoops"; + reg = <0x0 0xffc40000 0x0 0xc0000>; + record-size = <0x1000>; + console-size = <0x40000>; + msg-size = <0x20000 0x20000>; + }; + + cmdline_mem: memory@ffd00000 { + reg = <0x0 0xffd40000 0x0 0x1000>; + no-map; + }; + }; +}; + +&hsusb_phy1 { + status = "okay"; +}; + +&sdc2_state_off { + sd-cd { + pins = "gpio98"; + bias-disable; + drive-strength = <2>; + }; +}; + +&sdhc_1 { + status = "okay"; +}; + +&tlmm { + gpio-reserved-ranges = <22 2>, <28 6>; + + sdc2_state_on: sdc2-on { + clk { + pins = "sdc2_clk"; + bias-disable; + drive-strength = <16>; + }; + + cmd { + pins = "sdc2_cmd"; + bias-pull-up; + drive-strength = <10>; + }; + + data { + pins = "sdc2_data"; + bias-pull-up; + drive-strength = <10>; + }; + + sd-cd { + pins = "gpio98"; + bias-pull-up; + drive-strength = <2>; + }; + }; +}; + +&usb3 { + status = "okay"; +}; + +&usb3_dwc3 { + extcon = <&extcon_usb>; +}; diff --git a/dts/src/arm64/qcom/sm6125.dtsi b/dts/src/arm64/qcom/sm6125.dtsi new file mode 100644 index 0000000000..2b37ce6a9f --- /dev/null +++ b/dts/src/arm64/qcom/sm6125.dtsi @@ -0,0 +1,566 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2021, Martin Botka <martin.botka@somainline.org> + */ + +#include <dt-bindings/clock/qcom,gcc-sm6125.h> +#include <dt-bindings/clock/qcom,rpmcc.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/power/qcom-rpmpd.h> + +/ { + interrupt-parent = <&intc>; + #address-cells = <2>; + #size-cells = <2>; + + chosen { }; + + clocks { + xo_board: xo-board { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <19200000>; + clock-output-names = "xo_board"; + }; + + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32000>; + clock-output-names = "sleep_clk"; + }; + }; + + cpus { + #address-cells = <2>; + #size-cells = <0>; + + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "qcom,kryo260"; + reg = <0x0 0x0>; + enable-method = "psci"; + capacity-dmips-mhz = <1024>; + next-level-cache = <&L2_0>; + L2_0: l2-cache { + compatible = "cache"; + }; + }; + + CPU1: cpu@1 { + device_type = "cpu"; + compatible = "qcom,kryo260"; + reg = <0x0 0x1>; + enable-method = "psci"; + capacity-dmips-mhz = <1024>; + next-level-cache = <&L2_0>; + }; + + CPU2: cpu@2 { + device_type = "cpu"; + compatible = "qcom,kryo260"; + reg = <0x0 0x2>; + enable-method = "psci"; + capacity-dmips-mhz = <1024>; + next-level-cache = <&L2_0>; + }; + + CPU3: cpu@3 { + device_type = "cpu"; + compatible = "qcom,kryo260"; + reg = <0x0 0x3>; + enable-method = "psci"; + capacity-dmips-mhz = <1024>; + next-level-cache = <&L2_0>; + }; + + CPU4: cpu@100 { + device_type = "cpu"; + compatible = "qcom,kryo260"; + reg = <0x0 0x100>; + enable-method = "psci"; + capacity-dmips-mhz = <1638>; + next-level-cache = <&L2_1>; + L2_1: l2-cache { + compatible = "cache"; + }; + }; + + CPU5: cpu@101 { + device_type = "cpu"; + compatible = "qcom,kryo260"; + reg = <0x0 0x101>; + enable-method = "psci"; + capacity-dmips-mhz = <1638>; + next-level-cache = <&L2_1>; + }; + + CPU6: cpu@102 { + device_type = "cpu"; + compatible = "qcom,kryo260"; + reg = <0x0 0x102>; + enable-method = "psci"; + capacity-dmips-mhz = <1638>; + next-level-cache = <&L2_1>; + }; + + CPU7: cpu@103 { + device_type = "cpu"; + compatible = "qcom,kryo260"; + reg = <0x0 0x103>; + enable-method = "psci"; + capacity-dmips-mhz = <1638>; + next-level-cache = <&L2_1>; + }; + + cpu-map { + cluster0 { + core0 { + cpu = <&CPU0>; + }; + + core1 { + cpu = <&CPU1>; + }; + + core2 { + cpu = <&CPU2>; + }; + + core3 { + cpu = <&CPU3>; + }; + }; + + cluster1 { + core0 { + cpu = <&CPU4>; + }; + + core1 { + cpu = <&CPU5>; + }; + + core2 { + cpu = <&CPU6>; + }; + + core3 { + cpu = <&CPU7>; + }; + }; + }; + }; + + firmware { + scm: scm { + compatible = "qcom,scm-sm6125", "qcom,scm"; + #reset-cells = <1>; + }; + }; + + memory@40000000 { + /* We expect the bootloader to fill in the size */ + reg = <0x0 0x40000000 0x0 0x0>; + device_type = "memory"; + }; + + pmu { + compatible = "arm,armv8-pmuv3"; + interrupts = <GIC_PPI 6 IRQ_TYPE_LEVEL_HIGH>; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + reserved_memory: reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + hyp_mem: memory@45700000 { + reg = <0x0 0x45700000 0x0 0x600000>; + no-map; + }; + + xbl_aop_mem: memory@45e00000 { + reg = <0x0 0x45e00000 0x0 0x140000>; + no-map; + }; + + sec_apps_mem: memory@45fff000 { + reg = <0x0 0x45fff000 0x0 0x1000>; + no-map; + }; + + smem_mem: memory@46000000 { + reg = <0x0 0x46000000 0x0 0x200000>; + no-map; + }; + + reserved_mem1: memory@46200000 { + reg = <0x0 0x46200000 0x0 0x2d00000>; + no-map; + }; + + camera_mem: memory@4ab00000 { + reg = <0x0 0x4ab00000 0x0 0x500000>; + no-map; + }; + + modem_mem: memory@4b000000 { + reg = <0x0 0x4b000000 0x0 0x7e00000>; + no-map; + }; + + venus_mem: memory@52e00000 { + reg = <0x0 0x52e00000 0x0 0x500000>; + no-map; + }; + + wlan_msa_mem: memory@53300000 { + reg = <0x0 0x53300000 0x0 0x200000>; + no-map; + }; + + cdsp_mem: memory@53500000 { + reg = <0x0 0x53500000 0x0 0x1e00000>; + no-map; + }; + + adsp_pil_mem: memory@55300000 { + reg = <0x0 0x55300000 0x0 0x1e00000>; + no-map; + }; + + ipa_fw_mem: memory@57100000 { + reg = <0x0 0x57100000 0x0 0x10000>; + no-map; + }; + + ipa_gsi_mem: memory@57110000 { + reg = <0x0 0x57110000 0x0 0x5000>; + no-map; + }; + + gpu_mem: memory@57115000 { + reg = <0x0 0x57115000 0x0 0x2000>; + no-map; + }; + + cont_splash_mem: memory@5c000000 { + reg = <0x0 0x5c000000 0x0 0x00f00000>; + no-map; + }; + + dfps_data_mem: memory@5cf00000 { + reg = <0x0 0x5cf00000 0x0 0x0100000>; + no-map; + }; + + cdsp_sec_mem: memory@5f800000 { + reg = <0x0 0x5f800000 0x0 0x1e00000>; + no-map; + }; + + qseecom_mem: memory@5e400000 { + reg = <0x0 0x5e400000 0x0 0x1400000>; + no-map; + }; + + sdsp_mem: memory@f3000000 { + reg = <0x0 0xf3000000 0x0 0x400000>; + no-map; + }; + + adsp_mem: memory@f3400000 { + reg = <0x0 0xf3400000 0x0 0x800000>; + no-map; + }; + + qseecom_ta_mem: memory@13fc00000 { + reg = <0x1 0x3fc00000 0x0 0x400000>; + no-map; + }; + }; + + rpm-glink { + compatible = "qcom,glink-rpm"; + + interrupts = <GIC_SPI 194 IRQ_TYPE_EDGE_RISING>; + qcom,rpm-msg-ram = <&rpm_msg_ram>; + mboxes = <&apcs_glb 0>; + + rpm_requests: rpm-requests { + compatible = "qcom,rpm-sm6125"; + qcom,glink-channels = "rpm_requests"; + + rpmcc: clock-controller { + compatible = "qcom,rpmcc-sm6125", "qcom,rpmcc"; + #clock-cells = <1>; + }; + }; + }; + + smem: smem { + compatible = "qcom,smem"; + memory-region = <&smem_mem>; + hwlocks = <&tcsr_mutex 3>; + }; + + soc { + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x00 0x00 0x00 0xffffffff>; + compatible = "simple-bus"; + + tcsr_mutex: hwlock@340000 { + compatible = "qcom,tcsr-mutex"; + reg = <0x00340000 0x20000>; + #hwlock-cells = <1>; + }; + + tlmm: pinctrl@500000 { + compatible = "qcom,sm6125-tlmm"; + reg = <0x00500000 0x400000>, + <0x00900000 0x400000>, + <0x00d00000 0x400000>; + reg-names = "west", "south", "east"; + interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + gpio-ranges = <&tlmm 0 0 134>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + + sdc2_state_off: sdc2-off { + clk { + pins = "sdc2_clk"; + bias-disable; + drive-strength = <2>; + }; + + cmd { + pins = "sdc2_cmd"; + bias-pull-up; + drive-strength = <2>; + }; + + data { + pins = "sdc2_data"; + bias-pull-up; + drive-strength = <2>; + }; + }; + }; + + gcc: clock-controller@1400000 { + compatible = "qcom,gcc-sm6125"; + reg = <0x01400000 0x1f0000>; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + clock-names = "bi_tcxo", "sleep_clk"; + clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>, <&sleep_clk>; + }; + + hsusb_phy1: phy@1613000 { + compatible = "qcom,msm8996-qusb2-phy"; + reg = <0x01613000 0x180>; + #phy-cells = <0>; + + clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>, + <&gcc GCC_AHB2PHY_USB_CLK>; + clock-names = "ref", "cfg_ahb"; + + resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>; + status = "disabled"; + }; + + rpm_msg_ram: memory@45f0000 { + compatible = "qcom,rpm-msg-ram"; + reg = <0x045f0000 0x7000>; + }; + + sdhc_1: sdhci@4744000 { + compatible = "qcom,sm6125-sdhci", "qcom,sdhci-msm-v5"; + reg = <0x04744000 0x1000>, <0x04745000 0x1000>; + reg-names = "hc", "core"; + + interrupts = <GIC_SPI 348 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hc_irq", "pwr_irq"; + + clocks = <&gcc GCC_SDCC1_AHB_CLK>, + <&gcc GCC_SDCC1_APPS_CLK>, + <&xo_board>; + clock-names = "iface", "core", "xo"; + bus-width = <8>; + non-removable; + status = "disabled"; + }; + + sdhc_2: sdhci@4784000 { + compatible = "qcom,sm6125-sdhci", "qcom,sdhci-msm-v5"; + reg = <0x04784000 0x1000>; + reg-names = "hc"; + + interrupts = <GIC_SPI 350 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hc_irq", "pwr_irq"; + + clocks = <&gcc GCC_SDCC2_AHB_CLK>, + <&gcc GCC_SDCC2_APPS_CLK>, + <&xo_board>; + clock-names = "iface", "core", "xo"; + + pinctrl-0 = <&sdc2_state_on>; + pinctrl-1 = <&sdc2_state_off>; + pinctrl-names = "default", "sleep"; + + bus-width = <4>; + status = "disabled"; + }; + + usb3: usb@4ef8800 { + compatible = "qcom,msm8996-dwc3", "qcom,dwc3"; + reg = <0x04ef8800 0x400>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + clocks = <&gcc GCC_USB30_PRIM_MASTER_CLK>, + <&gcc GCC_SYS_NOC_USB3_PRIM_AXI_CLK>, + <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>, + <&gcc GCC_USB3_PRIM_CLKREF_CLK>, + <&gcc GCC_USB30_PRIM_SLEEP_CLK>, + <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>; + + assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>, + <&gcc GCC_USB30_PRIM_MASTER_CLK>; + assigned-clock-rates = <19200000>, <66666667>; + + power-domains = <&gcc USB30_PRIM_GDSC>; + qcom,select-utmi-as-pipe-clk; + status = "disabled"; + + usb3_dwc3: usb@4e00000 { + compatible = "snps,dwc3"; + reg = <0x04e00000 0xcd00>; + interrupts = <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>; + phys = <&hsusb_phy1>; + phy-names = "usb2-phy"; + snps,dis_u2_susphy_quirk; + snps,dis_enblslpm_quirk; + maximum-speed = "high-speed"; + dr_mode = "peripheral"; + }; + }; + + spmi_bus: spmi@1c40000 { + compatible = "qcom,spmi-pmic-arb"; + reg = <0x01c40000 0x1100>, + <0x01e00000 0x2000000>, + <0x03e00000 0x100000>, + <0x03f00000 0xa0000>, + <0x01c0a000 0x26000>; + reg-names = "core", "chnls", "obsrvr", "intr", "cnfg"; + interrupt-names = "periph_irq"; + interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>; + qcom,ee = <0>; + qcom,channel = <0>; + #address-cells = <2>; + #size-cells = <0>; + interrupt-controller; + #interrupt-cells = <4>; + cell-index = <0>; + }; + + apcs_glb: mailbox@f111000 { + compatible = "qcom,sm6125-apcs-hmss-global"; + reg = <0x0f111000 0x1000>; + + #mbox-cells = <1>; + }; + + timer@f120000 { + compatible = "arm,armv7-timer-mem"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + reg = <0x0f120000 0x1000>; + clock-frequency = <19200000>; + + frame@0f121000 { + frame-number = <0>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0f121000 0x1000>, + <0x0f122000 0x1000>; + }; + + frame@0f123000 { + frame-number = <1>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0f123000 0x1000>; + status = "disabled"; + }; + + frame@0f124000 { + frame-number = <2>; + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0f124000 0x1000>; + status = "disabled"; + }; + + frame@f125000 { + frame-number = <3>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0f125000 0x1000>; + status = "disabled"; + }; + + frame@f126000 { + frame-number = <4>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0f126000 0x1000>; + status = "disabled"; + }; + + frame@f127000 { + frame-number = <5>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0f127000 0x1000>; + status = "disabled"; + }; + + frame@f128000 { + frame-number = <6>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0f128000 0x1000>; + status = "disabled"; + }; + }; + + intc: interrupt-controller@f200000 { + compatible = "arm,gic-v3"; + reg = <0x0f200000 0x20000>, + <0x0f300000 0x100000>; + #interrupt-cells = <3>; + interrupt-controller; + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 1 0xf08 + GIC_PPI 2 0xf08 + GIC_PPI 3 0xf08 + GIC_PPI 0 0xf08>; + clock-frequency = <19200000>; + }; +}; diff --git a/dts/src/arm64/qcom/sm8150-mtp.dts b/dts/src/arm64/qcom/sm8150-mtp.dts index 53edf75411..b484371a60 100644 --- a/dts/src/arm64/qcom/sm8150-mtp.dts +++ b/dts/src/arm64/qcom/sm8150-mtp.dts @@ -15,7 +15,7 @@ / { model = "Qualcomm Technologies, Inc. SM8150 MTP"; - compatible = "qcom,sm8150-mtp"; + compatible = "qcom,sm8150-mtp", "qcom,sm8150"; aliases { serial0 = &uart2; diff --git a/dts/src/arm64/qcom/sm8150.dtsi b/dts/src/arm64/qcom/sm8150.dtsi index eef9d79157..ef0232c2cf 100644 --- a/dts/src/arm64/qcom/sm8150.dtsi +++ b/dts/src/arm64/qcom/sm8150.dtsi @@ -13,6 +13,7 @@ #include <dt-bindings/clock/qcom,gcc-sm8150.h> #include <dt-bindings/clock/qcom,gpucc-sm8150.h> #include <dt-bindings/interconnect/qcom,osm-l3.h> +#include <dt-bindings/interconnect/qcom,sm8150.h> #include <dt-bindings/thermal/thermal.h> / { @@ -52,6 +53,9 @@ dynamic-power-coefficient = <232>; next-level-cache = <&L2_0>; qcom,freq-domain = <&cpufreq_hw 0>; + operating-points-v2 = <&cpu0_opp_table>; + interconnects = <&gem_noc MASTER_AMPSS_M0 &mc_virt SLAVE_EBI_CH0>, + <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>; power-domains = <&CPU_PD0>; power-domain-names = "psci"; #cooling-cells = <2>; @@ -73,6 +77,9 @@ dynamic-power-coefficient = <232>; next-level-cache = <&L2_100>; qcom,freq-domain = <&cpufreq_hw 0>; + operating-points-v2 = <&cpu0_opp_table>; + interconnects = <&gem_noc MASTER_AMPSS_M0 &mc_virt SLAVE_EBI_CH0>, + <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>; power-domains = <&CPU_PD1>; power-domain-names = "psci"; #cooling-cells = <2>; @@ -92,6 +99,9 @@ dynamic-power-coefficient = <232>; next-level-cache = <&L2_200>; qcom,freq-domain = <&cpufreq_hw 0>; + operating-points-v2 = <&cpu0_opp_table>; + interconnects = <&gem_noc MASTER_AMPSS_M0 &mc_virt SLAVE_EBI_CH0>, + <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>; power-domains = <&CPU_PD2>; power-domain-names = "psci"; #cooling-cells = <2>; @@ -110,6 +120,9 @@ dynamic-power-coefficient = <232>; next-level-cache = <&L2_300>; qcom,freq-domain = <&cpufreq_hw 0>; + operating-points-v2 = <&cpu0_opp_table>; + interconnects = <&gem_noc MASTER_AMPSS_M0 &mc_virt SLAVE_EBI_CH0>, + <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>; power-domains = <&CPU_PD3>; power-domain-names = "psci"; #cooling-cells = <2>; @@ -128,6 +141,9 @@ dynamic-power-coefficient = <369>; next-level-cache = <&L2_400>; qcom,freq-domain = <&cpufreq_hw 1>; + operating-points-v2 = <&cpu4_opp_table>; + interconnects = <&gem_noc MASTER_AMPSS_M0 &mc_virt SLAVE_EBI_CH0>, + <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>; power-domains = <&CPU_PD4>; power-domain-names = "psci"; #cooling-cells = <2>; @@ -146,6 +162,9 @@ dynamic-power-coefficient = <369>; next-level-cache = <&L2_500>; qcom,freq-domain = <&cpufreq_hw 1>; + operating-points-v2 = <&cpu4_opp_table>; + interconnects = <&gem_noc MASTER_AMPSS_M0 &mc_virt SLAVE_EBI_CH0>, + <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>; power-domains = <&CPU_PD5>; power-domain-names = "psci"; #cooling-cells = <2>; @@ -164,6 +183,9 @@ dynamic-power-coefficient = <369>; next-level-cache = <&L2_600>; qcom,freq-domain = <&cpufreq_hw 1>; + operating-points-v2 = <&cpu4_opp_table>; + interconnects = <&gem_noc MASTER_AMPSS_M0 &mc_virt SLAVE_EBI_CH0>, + <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>; power-domains = <&CPU_PD6>; power-domain-names = "psci"; #cooling-cells = <2>; @@ -182,6 +204,9 @@ dynamic-power-coefficient = <421>; next-level-cache = <&L2_700>; qcom,freq-domain = <&cpufreq_hw 2>; + operating-points-v2 = <&cpu7_opp_table>; + interconnects = <&gem_noc MASTER_AMPSS_M0 &mc_virt SLAVE_EBI_CH0>, + <&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>; power-domains = <&CPU_PD7>; power-domain-names = "psci"; #cooling-cells = <2>; @@ -264,6 +289,296 @@ }; }; + cpu0_opp_table: cpu0_opp_table { + compatible = "operating-points-v2"; + opp-shared; + + cpu0_opp1: opp-300000000 { + opp-hz = /bits/ 64 <300000000>; + opp-peak-kBps = <800000 9600000>; + }; + + cpu0_opp2: opp-403200000 { + opp-hz = /bits/ 64 <403200000>; + opp-peak-kBps = <800000 9600000>; + }; + + cpu0_opp3: opp-499200000 { + opp-hz = /bits/ 64 <499200000>; + opp-peak-kBps = <800000 12902400>; + }; + + cpu0_opp4: opp-576000000 { + opp-hz = /bits/ 64 <576000000>; + opp-peak-kBps = <800000 12902400>; + }; + + cpu0_opp5: opp-672000000 { + opp-hz = /bits/ 64 <672000000>; + opp-peak-kBps = <800000 15974400>; + }; + + cpu0_opp6: opp-768000000 { + opp-hz = /bits/ 64 <768000000>; + opp-peak-kBps = <1804000 19660800>; + }; + + cpu0_opp7: opp-844800000 { + opp-hz = /bits/ 64 <844800000>; + opp-peak-kBps = <1804000 19660800>; + }; + + cpu0_opp8: opp-940800000 { + opp-hz = /bits/ 64 <940800000>; + opp-peak-kBps = <1804000 22732800>; + }; + + cpu0_opp9: opp-1036800000 { + opp-hz = /bits/ 64 <1036800000>; + opp-peak-kBps = <1804000 22732800>; + }; + + cpu0_opp10: opp-1113600000 { + opp-hz = /bits/ 64 <1113600000>; + opp-peak-kBps = <2188000 25804800>; + }; + + cpu0_opp11: opp-1209600000 { + opp-hz = /bits/ 64 <1209600000>; + opp-peak-kBps = <2188000 31948800>; + }; + + cpu0_opp12: opp-1305600000 { + opp-hz = /bits/ 64 <1305600000>; + opp-peak-kBps = <3072000 31948800>; + }; + + cpu0_opp13: opp-1382400000 { + opp-hz = /bits/ 64 <1382400000>; + opp-peak-kBps = <3072000 31948800>; + }; + + cpu0_opp14: opp-1478400000 { + opp-hz = /bits/ 64 <1478400000>; + opp-peak-kBps = <3072000 31948800>; + }; + + cpu0_opp15: opp-1555200000 { + opp-hz = /bits/ 64 <1555200000>; + opp-peak-kBps = <3072000 40550400>; + }; + + cpu0_opp16: opp-1632000000 { + opp-hz = /bits/ 64 <1632000000>; + opp-peak-kBps = <3072000 40550400>; + }; + + cpu0_opp17: opp-1708800000 { + opp-hz = /bits/ 64 <1708800000>; + opp-peak-kBps = <3072000 43008000>; + }; + + cpu0_opp18: opp-1785600000 { + opp-hz = /bits/ 64 <1785600000>; + opp-peak-kBps = <3072000 43008000>; + }; + }; + + cpu4_opp_table: cpu4_opp_table { + compatible = "operating-points-v2"; + opp-shared; + + cpu4_opp1: opp-710400000 { + opp-hz = /bits/ 64 <710400000>; + opp-peak-kBps = <1804000 15974400>; + }; + + cpu4_opp2: opp-825600000 { + opp-hz = /bits/ 64 <825600000>; + opp-peak-kBps = <2188000 19660800>; + }; + + cpu4_opp3: opp-940800000 { + opp-hz = /bits/ 64 <940800000>; + opp-peak-kBps = <2188000 22732800>; + }; + + cpu4_opp4: opp-1056000000 { + opp-hz = /bits/ 64 <1056000000>; + opp-peak-kBps = <3072000 25804800>; + }; + + cpu4_opp5: opp-1171200000 { + opp-hz = /bits/ 64 <1171200000>; + opp-peak-kBps = <3072000 31948800>; + }; + + cpu4_opp6: opp-1286400000 { + opp-hz = /bits/ 64 <1286400000>; + opp-peak-kBps = <4068000 31948800>; + }; + + cpu4_opp7: opp-1401600000 { + opp-hz = /bits/ 64 <1401600000>; + opp-peak-kBps = <4068000 31948800>; + }; + + cpu4_opp8: opp-1497600000 { + opp-hz = /bits/ 64 <1497600000>; + opp-peak-kBps = <4068000 40550400>; + }; + + cpu4_opp9: opp-1612800000 { + opp-hz = /bits/ 64 <1612800000>; + opp-peak-kBps = <4068000 40550400>; + }; + + cpu4_opp10: opp-1708800000 { + opp-hz = /bits/ 64 <1708800000>; + opp-peak-kBps = <4068000 43008000>; + }; + + cpu4_opp11: opp-1804800000 { + opp-hz = /bits/ 64 <1804800000>; + opp-peak-kBps = <6220000 43008000>; + }; + + cpu4_opp12: opp-1920000000 { + opp-hz = /bits/ 64 <1920000000>; + opp-peak-kBps = <6220000 49152000>; + }; + + cpu4_opp13: opp-2016000000 { + opp-hz = /bits/ 64 <2016000000>; + opp-peak-kBps = <7216000 49152000>; + }; + + cpu4_opp14: opp-2131200000 { + opp-hz = /bits/ 64 <2131200000>; + opp-peak-kBps = <8368000 49152000>; + }; + + cpu4_opp15: opp-2227200000 { + opp-hz = /bits/ 64 <2227200000>; + opp-peak-kBps = <8368000 51609600>; + }; + + cpu4_opp16: opp-2323200000 { + opp-hz = /bits/ 64 <2323200000>; + opp-peak-kBps = <8368000 51609600>; + }; + + cpu4_opp17: opp-2419200000 { + opp-hz = /bits/ 64 <2419200000>; + opp-peak-kBps = <8368000 51609600>; + }; + }; + + cpu7_opp_table: cpu7_opp_table { + compatible = "operating-points-v2"; + opp-shared; + + cpu7_opp1: opp-825600000 { + opp-hz = /bits/ 64 <825600000>; + opp-peak-kBps = <2188000 19660800>; + }; + + cpu7_opp2: opp-940800000 { + opp-hz = /bits/ 64 <940800000>; + opp-peak-kBps = <2188000 22732800>; + }; + + cpu7_opp3: opp-1056000000 { + opp-hz = /bits/ 64 <1056000000>; + opp-peak-kBps = <3072000 25804800>; + }; + + cpu7_opp4: opp-1171200000 { + opp-hz = /bits/ 64 <1171200000>; + opp-peak-kBps = <3072000 31948800>; + }; + + cpu7_opp5: opp-1286400000 { + opp-hz = /bits/ 64 <1286400000>; + opp-peak-kBps = <4068000 31948800>; + }; + + cpu7_opp6: opp-1401600000 { + opp-hz = /bits/ 64 <1401600000>; + opp-peak-kBps = <4068000 31948800>; + }; + + cpu7_opp7: opp-1497600000 { + opp-hz = /bits/ 64 <1497600000>; + opp-peak-kBps = <4068000 40550400>; + }; + + cpu7_opp8: opp-1612800000 { + opp-hz = /bits/ 64 <1612800000>; + opp-peak-kBps = <4068000 40550400>; + }; + + cpu7_opp9: opp-1708800000 { + opp-hz = /bits/ 64 <1708800000>; + opp-peak-kBps = <4068000 43008000>; + }; + + cpu7_opp10: opp-1804800000 { + opp-hz = /bits/ 64 <1804800000>; + opp-peak-kBps = <6220000 43008000>; + }; + + cpu7_opp11: opp-1920000000 { + opp-hz = /bits/ 64 <1920000000>; + opp-peak-kBps = <6220000 49152000>; + }; + + cpu7_opp12: opp-2016000000 { + opp-hz = /bits/ 64 <2016000000>; + opp-peak-kBps = <7216000 49152000>; + }; + + cpu7_opp13: opp-2131200000 { + opp-hz = /bits/ 64 <2131200000>; + opp-peak-kBps = <8368000 49152000>; + }; + + cpu7_opp14: opp-2227200000 { + opp-hz = /bits/ 64 <2227200000>; + opp-peak-kBps = <8368000 51609600>; + }; + + cpu7_opp15: opp-2323200000 { + opp-hz = /bits/ 64 <2323200000>; + opp-peak-kBps = <8368000 51609600>; + }; + + cpu7_opp16: opp-2419200000 { + opp-hz = /bits/ 64 <2419200000>; + opp-peak-kBps = <8368000 51609600>; + }; + + cpu7_opp17: opp-2534400000 { + opp-hz = /bits/ 64 <2534400000>; + opp-peak-kBps = <8368000 51609600>; + }; + + cpu7_opp18: opp-2649600000 { + opp-hz = /bits/ 64 <2649600000>; + opp-peak-kBps = <8368000 51609600>; + }; + + cpu7_opp19: opp-2745600000 { + opp-hz = /bits/ 64 <2745600000>; + opp-peak-kBps = <8368000 51609600>; + }; + + cpu7_opp20: opp-2841600000 { + opp-hz = /bits/ 64 <2841600000>; + opp-peak-kBps = <8368000 51609600>; + }; + }; + firmware { scm: scm { compatible = "qcom,scm-sm8150", "qcom,scm"; @@ -626,6 +941,21 @@ status = "disabled"; }; + spi0: spi@880000 { + compatible = "qcom,geni-spi"; + reg = <0 0x880000 0 0x4000>; + reg-names = "se"; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi0_default>; + interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>; + spi-max-frequency = <50000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + i2c1: i2c@884000 { compatible = "qcom,geni-i2c"; reg = <0 0x00884000 0 0x4000>; @@ -639,6 +969,21 @@ status = "disabled"; }; + spi1: spi@884000 { + compatible = "qcom,geni-spi"; + reg = <0 0x884000 0 0x4000>; + reg-names = "se"; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi1_default>; + interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>; + spi-max-frequency = <50000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + i2c2: i2c@888000 { compatible = "qcom,geni-i2c"; reg = <0 0x00888000 0 0x4000>; @@ -652,6 +997,21 @@ status = "disabled"; }; + spi2: spi@888000 { + compatible = "qcom,geni-spi"; + reg = <0 0x888000 0 0x4000>; + reg-names = "se"; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi2_default>; + interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>; + spi-max-frequency = <50000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + i2c3: i2c@88c000 { compatible = "qcom,geni-i2c"; reg = <0 0x0088c000 0 0x4000>; @@ -665,6 +1025,21 @@ status = "disabled"; }; + spi3: spi@88c000 { + compatible = "qcom,geni-spi"; + reg = <0 0x88c000 0 0x4000>; + reg-names = "se"; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi3_default>; + interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>; + spi-max-frequency = <50000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + i2c4: i2c@890000 { compatible = "qcom,geni-i2c"; reg = <0 0x00890000 0 0x4000>; @@ -678,6 +1053,21 @@ status = "disabled"; }; + spi4: spi@890000 { + compatible = "qcom,geni-spi"; + reg = <0 0x890000 0 0x4000>; + reg-names = "se"; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi4_default>; + interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>; + spi-max-frequency = <50000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + i2c5: i2c@894000 { compatible = "qcom,geni-i2c"; reg = <0 0x00894000 0 0x4000>; @@ -691,6 +1081,21 @@ status = "disabled"; }; + spi5: spi@894000 { + compatible = "qcom,geni-spi"; + reg = <0 0x894000 0 0x4000>; + reg-names = "se"; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi5_default>; + interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>; + spi-max-frequency = <50000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + i2c6: i2c@898000 { compatible = "qcom,geni-i2c"; reg = <0 0x00898000 0 0x4000>; @@ -704,6 +1109,21 @@ status = "disabled"; }; + spi6: spi@898000 { + compatible = "qcom,geni-spi"; + reg = <0 0x898000 0 0x4000>; + reg-names = "se"; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi6_default>; + interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>; + spi-max-frequency = <50000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + i2c7: i2c@89c000 { compatible = "qcom,geni-i2c"; reg = <0 0x0089c000 0 0x4000>; @@ -717,6 +1137,20 @@ status = "disabled"; }; + spi7: spi@89c000 { + compatible = "qcom,geni-spi"; + reg = <0 0x89c000 0 0x4000>; + reg-names = "se"; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi7_default>; + interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>; + spi-max-frequency = <50000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; }; gpi_dma1: dma-controller@a00000 { @@ -767,6 +1201,21 @@ status = "disabled"; }; + spi8: spi@a80000 { + compatible = "qcom,geni-spi"; + reg = <0 0xa80000 0 0x4000>; + reg-names = "se"; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi8_default>; + interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>; + spi-max-frequency = <50000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + i2c9: i2c@a84000 { compatible = "qcom,geni-i2c"; reg = <0 0x00a84000 0 0x4000>; @@ -780,6 +1229,21 @@ status = "disabled"; }; + spi9: spi@a84000 { + compatible = "qcom,geni-spi"; + reg = <0 0xa84000 0 0x4000>; + reg-names = "se"; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi9_default>; + interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>; + spi-max-frequency = <50000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + i2c10: i2c@a88000 { compatible = "qcom,geni-i2c"; reg = <0 0x00a88000 0 0x4000>; @@ -793,6 +1257,21 @@ status = "disabled"; }; + spi10: spi@a88000 { + compatible = "qcom,geni-spi"; + reg = <0 0xa88000 0 0x4000>; + reg-names = "se"; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi10_default>; + interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>; + spi-max-frequency = <50000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + i2c11: i2c@a8c000 { compatible = "qcom,geni-i2c"; reg = <0 0x00a8c000 0 0x4000>; @@ -806,6 +1285,21 @@ status = "disabled"; }; + spi11: spi@a8c000 { + compatible = "qcom,geni-spi"; + reg = <0 0xa8c000 0 0x4000>; + reg-names = "se"; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi11_default>; + interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>; + spi-max-frequency = <50000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + uart2: serial@a90000 { compatible = "qcom,geni-debug-uart"; reg = <0x0 0x00a90000 0x0 0x4000>; @@ -828,6 +1322,21 @@ status = "disabled"; }; + spi12: spi@a90000 { + compatible = "qcom,geni-spi"; + reg = <0 0xa90000 0 0x4000>; + reg-names = "se"; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi12_default>; + interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>; + spi-max-frequency = <50000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + i2c16: i2c@94000 { compatible = "qcom,geni-i2c"; reg = <0 0x0094000 0 0x4000>; @@ -840,6 +1349,21 @@ #size-cells = <0>; status = "disabled"; }; + + spi16: spi@a94000 { + compatible = "qcom,geni-spi"; + reg = <0 0xa94000 0 0x4000>; + reg-names = "se"; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi16_default>; + interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>; + spi-max-frequency = <50000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; }; gpi_dma2: dma-controller@c00000 { @@ -891,6 +1415,21 @@ status = "disabled"; }; + spi17: spi@c80000 { + compatible = "qcom,geni-spi"; + reg = <0 0xc80000 0 0x4000>; + reg-names = "se"; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi17_default>; + interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>; + spi-max-frequency = <50000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + i2c18: i2c@c84000 { compatible = "qcom,geni-i2c"; reg = <0 0x00c84000 0 0x4000>; @@ -904,6 +1443,21 @@ status = "disabled"; }; + spi18: spi@c84000 { + compatible = "qcom,geni-spi"; + reg = <0 0xc84000 0 0x4000>; + reg-names = "se"; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi18_default>; + interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>; + spi-max-frequency = <50000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + i2c19: i2c@c88000 { compatible = "qcom,geni-i2c"; reg = <0 0x00c88000 0 0x4000>; @@ -917,6 +1471,21 @@ status = "disabled"; }; + spi19: spi@c88000 { + compatible = "qcom,geni-spi"; + reg = <0 0xc88000 0 0x4000>; + reg-names = "se"; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi19_default>; + interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>; + spi-max-frequency = <50000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + i2c13: i2c@c8c000 { compatible = "qcom,geni-i2c"; reg = <0 0x00c8c000 0 0x4000>; @@ -930,6 +1499,21 @@ status = "disabled"; }; + spi13: spi@c8c000 { + compatible = "qcom,geni-spi"; + reg = <0 0xc8c000 0 0x4000>; + reg-names = "se"; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi13_default>; + interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>; + spi-max-frequency = <50000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + i2c14: i2c@c90000 { compatible = "qcom,geni-i2c"; reg = <0 0x00c90000 0 0x4000>; @@ -943,6 +1527,21 @@ status = "disabled"; }; + spi14: spi@c90000 { + compatible = "qcom,geni-spi"; + reg = <0 0xc90000 0 0x4000>; + reg-names = "se"; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi14_default>; + interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>; + spi-max-frequency = <50000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + i2c15: i2c@c94000 { compatible = "qcom,geni-i2c"; reg = <0 0x00c94000 0 0x4000>; @@ -955,6 +1554,21 @@ #size-cells = <0>; status = "disabled"; }; + + spi15: spi@c94000 { + compatible = "qcom,geni-spi"; + reg = <0 0xc94000 0 0x4000>; + reg-names = "se"; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi15_default>; + interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>; + spi-max-frequency = <50000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; }; config_noc: interconnect@1500000 { @@ -1016,7 +1630,9 @@ ufs_mem_hc: ufshc@1d84000 { compatible = "qcom,sm8150-ufshc", "qcom,ufshc", "jedec,ufs-2.0"; - reg = <0 0x01d84000 0 0x2500>; + reg = <0 0x01d84000 0 0x2500>, + <0 0x01d90000 0 0x8000>; + reg-names = "std", "ice"; interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>; phys = <&ufs_mem_phy_lanes>; phy-names = "ufsphy"; @@ -1035,7 +1651,8 @@ "ref_clk", "tx_lane0_sync_clk", "rx_lane0_sync_clk", - "rx_lane1_sync_clk"; + "rx_lane1_sync_clk", + "ice_core_clk"; clocks = <&gcc GCC_UFS_PHY_AXI_CLK>, <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>, @@ -1044,7 +1661,8 @@ <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>, <&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>, - <&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>; + <&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>, + <&gcc GCC_UFS_PHY_ICE_CORE_CLK>; freq-table-hz = <37500000 300000000>, <0 0>, @@ -1053,7 +1671,8 @@ <0 0>, <0 0>, <0 0>, - <0 0>; + <0 0>, + <0 300000000>; status = "disabled"; }; @@ -1296,6 +1915,13 @@ }; }; + qup_spi0_default: qup-spi0-default { + pins = "gpio0", "gpio1", "gpio2", "gpio3"; + function = "qup0"; + drive-strength = <6>; + bias-disable; + }; + qup_i2c1_default: qup-i2c1-default { mux { pins = "gpio114", "gpio115"; @@ -1309,6 +1935,13 @@ }; }; + qup_spi1_default: qup-spi1-default { + pins = "gpio114", "gpio115", "gpio116", "gpio117"; + function = "qup1"; + drive-strength = <6>; + bias-disable; + }; + qup_i2c2_default: qup-i2c2-default { mux { pins = "gpio126", "gpio127"; @@ -1322,6 +1955,13 @@ }; }; + qup_spi2_default: qup-spi2-default { + pins = "gpio126", "gpio127", "gpio128", "gpio129"; + function = "qup2"; + drive-strength = <6>; + bias-disable; + }; + qup_i2c3_default: qup-i2c3-default { mux { pins = "gpio144", "gpio145"; @@ -1335,6 +1975,13 @@ }; }; + qup_spi3_default: qup-spi3-default { + pins = "gpio144", "gpio145", "gpio146", "gpio147"; + function = "qup3"; + drive-strength = <6>; + bias-disable; + }; + qup_i2c4_default: qup-i2c4-default { mux { pins = "gpio51", "gpio52"; @@ -1348,6 +1995,13 @@ }; }; + qup_spi4_default: qup-spi4-default { + pins = "gpio51", "gpio52", "gpio53", "gpio54"; + function = "qup4"; + drive-strength = <6>; + bias-disable; + }; + qup_i2c5_default: qup-i2c5-default { mux { pins = "gpio121", "gpio122"; @@ -1361,6 +2015,13 @@ }; }; + qup_spi5_default: qup-spi5-default { + pins = "gpio119", "gpio120", "gpio121", "gpio122"; + function = "qup5"; + drive-strength = <6>; + bias-disable; + }; + qup_i2c6_default: qup-i2c6-default { mux { pins = "gpio6", "gpio7"; @@ -1374,6 +2035,13 @@ }; }; + qup_spi6_default: qup-spi6_default { + pins = "gpio4", "gpio5", "gpio6", "gpio7"; + function = "qup6"; + drive-strength = <6>; + bias-disable; + }; + qup_i2c7_default: qup-i2c7-default { mux { pins = "gpio98", "gpio99"; @@ -1387,6 +2055,13 @@ }; }; + qup_spi7_default: qup-spi7_default { + pins = "gpio98", "gpio99", "gpio100", "gpio101"; + function = "qup7"; + drive-strength = <6>; + bias-disable; + }; + qup_i2c8_default: qup-i2c8-default { mux { pins = "gpio88", "gpio89"; @@ -1400,6 +2075,13 @@ }; }; + qup_spi8_default: qup-spi8-default { + pins = "gpio88", "gpio89", "gpio90", "gpio91"; + function = "qup8"; + drive-strength = <6>; + bias-disable; + }; + qup_i2c9_default: qup-i2c9-default { mux { pins = "gpio39", "gpio40"; @@ -1413,6 +2095,13 @@ }; }; + qup_spi9_default: qup-spi9-default { + pins = "gpio39", "gpio40", "gpio41", "gpio42"; + function = "qup9"; + drive-strength = <6>; + bias-disable; + }; + qup_i2c10_default: qup-i2c10-default { mux { pins = "gpio9", "gpio10"; @@ -1426,6 +2115,13 @@ }; }; + qup_spi10_default: qup-spi10-default { + pins = "gpio9", "gpio10", "gpio11", "gpio12"; + function = "qup10"; + drive-strength = <6>; + bias-disable; + }; + qup_i2c11_default: qup-i2c11-default { mux { pins = "gpio94", "gpio95"; @@ -1439,6 +2135,13 @@ }; }; + qup_spi11_default: qup-spi11-default { + pins = "gpio92", "gpio93", "gpio94", "gpio95"; + function = "qup11"; + drive-strength = <6>; + bias-disable; + }; + qup_i2c12_default: qup-i2c12-default { mux { pins = "gpio83", "gpio84"; @@ -1452,6 +2155,13 @@ }; }; + qup_spi12_default: qup-spi12-default { + pins = "gpio83", "gpio84", "gpio85", "gpio86"; + function = "qup12"; + drive-strength = <6>; + bias-disable; + }; + qup_i2c13_default: qup-i2c13-default { mux { pins = "gpio43", "gpio44"; @@ -1465,6 +2175,13 @@ }; }; + qup_spi13_default: qup-spi13-default { + pins = "gpio43", "gpio44", "gpio45", "gpio46"; + function = "qup13"; + drive-strength = <6>; + bias-disable; + }; + qup_i2c14_default: qup-i2c14-default { mux { pins = "gpio47", "gpio48"; @@ -1478,6 +2195,13 @@ }; }; + qup_spi14_default: qup-spi14-default { + pins = "gpio47", "gpio48", "gpio49", "gpio50"; + function = "qup14"; + drive-strength = <6>; + bias-disable; + }; + qup_i2c15_default: qup-i2c15-default { mux { pins = "gpio27", "gpio28"; @@ -1491,6 +2215,13 @@ }; }; + qup_spi15_default: qup-spi15-default { + pins = "gpio27", "gpio28", "gpio29", "gpio30"; + function = "qup15"; + drive-strength = <6>; + bias-disable; + }; + qup_i2c16_default: qup-i2c16-default { mux { pins = "gpio86", "gpio85"; @@ -1504,6 +2235,13 @@ }; }; + qup_spi16_default: qup-spi16-default { + pins = "gpio83", "gpio84", "gpio85", "gpio86"; + function = "qup16"; + drive-strength = <6>; + bias-disable; + }; + qup_i2c17_default: qup-i2c17-default { mux { pins = "gpio55", "gpio56"; @@ -1517,6 +2255,13 @@ }; }; + qup_spi17_default: qup-spi17-default { + pins = "gpio55", "gpio56", "gpio57", "gpio58"; + function = "qup17"; + drive-strength = <6>; + bias-disable; + }; + qup_i2c18_default: qup-i2c18-default { mux { pins = "gpio23", "gpio24"; @@ -1530,6 +2275,13 @@ }; }; + qup_spi18_default: qup-spi18-default { + pins = "gpio23", "gpio24", "gpio25", "gpio26"; + function = "qup18"; + drive-strength = <6>; + bias-disable; + }; + qup_i2c19_default: qup-i2c19-default { mux { pins = "gpio57", "gpio58"; @@ -1542,6 +2294,13 @@ bias-disable; }; }; + + qup_spi19_default: qup-spi19-default { + pins = "gpio55", "gpio56", "gpio57", "gpio58"; + function = "qup19"; + drive-strength = <6>; + bias-disable; + }; }; remoteproc_mpss: remoteproc@4080000 { @@ -2266,20 +3025,6 @@ }; }; - dc_noc: interconnect@9160000 { - compatible = "qcom,sm8150-dc-noc"; - reg = <0 0x09160000 0 0x3200>; - #interconnect-cells = <1>; - qcom,bcm-voters = <&apps_bcm_voter>; - }; - - gem_noc: interconnect@9680000 { - compatible = "qcom,sm8150-gem-noc"; - reg = <0 0x09680000 0 0x3e200>; - #interconnect-cells = <1>; - qcom,bcm-voters = <&apps_bcm_voter>; - }; - usb_2_qmpphy: phy@88eb000 { compatible = "qcom,sm8150-qmp-usb3-uni-phy"; reg = <0 0x088eb000 0 0x200>; @@ -2311,6 +3056,20 @@ }; }; + dc_noc: interconnect@9160000 { + compatible = "qcom,sm8150-dc-noc"; + reg = <0 0x09160000 0 0x3200>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + gem_noc: interconnect@9680000 { + compatible = "qcom,sm8150-gem-noc"; + reg = <0 0x09680000 0 0x3e200>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + usb_1: usb@a6f8800 { compatible = "qcom,sm8150-dwc3", "qcom,dwc3"; reg = <0 0x0a6f8800 0 0x400>; @@ -2389,7 +3148,7 @@ resets = <&gcc GCC_USB30_SEC_BCR>; - usb_2_dwc3: dwc3@a800000 { + usb_2_dwc3: usb@a800000 { compatible = "snps,dwc3"; reg = <0 0x0a800000 0 0xcd00>; interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; diff --git a/dts/src/arm64/qcom/sm8250.dtsi b/dts/src/arm64/qcom/sm8250.dtsi index 4798368b02..8c15d9fed0 100644 --- a/dts/src/arm64/qcom/sm8250.dtsi +++ b/dts/src/arm64/qcom/sm8250.dtsi @@ -561,6 +561,9 @@ pinctrl-names = "default"; pinctrl-0 = <&qup_i2c14_default>; interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&gpi_dma2 0 0 QCOM_GPI_I2C>, + <&gpi_dma2 1 0 QCOM_GPI_I2C>; + dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -572,10 +575,13 @@ clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>; interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; + dmas = <&gpi_dma2 0 0 QCOM_GPI_SPI>, + <&gpi_dma2 1 0 QCOM_GPI_SPI>; + dma-names = "tx", "rx"; power-domains = <&rpmhpd SM8250_CX>; operating-points-v2 = <&qup_opp_table>; + #address-cells = <1>; + #size-cells = <0>; status = "disabled"; }; @@ -587,6 +593,9 @@ pinctrl-names = "default"; pinctrl-0 = <&qup_i2c15_default>; interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&gpi_dma2 0 1 QCOM_GPI_I2C>, + <&gpi_dma2 1 1 QCOM_GPI_I2C>; + dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -598,10 +607,13 @@ clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>; interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; + dmas = <&gpi_dma2 0 1 QCOM_GPI_SPI>, + <&gpi_dma2 1 1 QCOM_GPI_SPI>; + dma-names = "tx", "rx"; power-domains = <&rpmhpd SM8250_CX>; operating-points-v2 = <&qup_opp_table>; + #address-cells = <1>; + #size-cells = <0>; status = "disabled"; }; @@ -613,6 +625,9 @@ pinctrl-names = "default"; pinctrl-0 = <&qup_i2c16_default>; interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&gpi_dma2 0 2 QCOM_GPI_I2C>, + <&gpi_dma2 1 2 QCOM_GPI_I2C>; + dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -624,10 +639,13 @@ clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>; interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; + dmas = <&gpi_dma2 0 2 QCOM_GPI_SPI>, + <&gpi_dma2 1 2 QCOM_GPI_SPI>; + dma-names = "tx", "rx"; power-domains = <&rpmhpd SM8250_CX>; operating-points-v2 = <&qup_opp_table>; + #address-cells = <1>; + #size-cells = <0>; status = "disabled"; }; @@ -639,6 +657,9 @@ pinctrl-names = "default"; pinctrl-0 = <&qup_i2c17_default>; interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&gpi_dma2 0 3 QCOM_GPI_I2C>, + <&gpi_dma2 1 3 QCOM_GPI_I2C>; + dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -650,10 +671,13 @@ clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>; interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; + dmas = <&gpi_dma2 0 3 QCOM_GPI_SPI>, + <&gpi_dma2 1 3 QCOM_GPI_SPI>; + dma-names = "tx", "rx"; power-domains = <&rpmhpd SM8250_CX>; operating-points-v2 = <&qup_opp_table>; + #address-cells = <1>; + #size-cells = <0>; status = "disabled"; }; @@ -678,6 +702,9 @@ pinctrl-names = "default"; pinctrl-0 = <&qup_i2c18_default>; interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&gpi_dma2 0 4 QCOM_GPI_I2C>, + <&gpi_dma2 1 4 QCOM_GPI_I2C>; + dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -689,10 +716,13 @@ clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>; interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; + dmas = <&gpi_dma2 0 4 QCOM_GPI_SPI>, + <&gpi_dma2 1 4 QCOM_GPI_SPI>; + dma-names = "tx", "rx"; power-domains = <&rpmhpd SM8250_CX>; operating-points-v2 = <&qup_opp_table>; + #address-cells = <1>; + #size-cells = <0>; status = "disabled"; }; @@ -717,6 +747,9 @@ pinctrl-names = "default"; pinctrl-0 = <&qup_i2c19_default>; interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&gpi_dma2 0 5 QCOM_GPI_I2C>, + <&gpi_dma2 1 5 QCOM_GPI_I2C>; + dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -728,10 +761,13 @@ clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>; interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; + dmas = <&gpi_dma2 0 5 QCOM_GPI_SPI>, + <&gpi_dma2 1 5 QCOM_GPI_SPI>; + dma-names = "tx", "rx"; power-domains = <&rpmhpd SM8250_CX>; operating-points-v2 = <&qup_opp_table>; + #address-cells = <1>; + #size-cells = <0>; status = "disabled"; }; }; @@ -779,6 +815,9 @@ pinctrl-names = "default"; pinctrl-0 = <&qup_i2c0_default>; interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>, + <&gpi_dma0 1 0 QCOM_GPI_I2C>; + dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -790,10 +829,13 @@ clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>; interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; + dmas = <&gpi_dma0 0 0 QCOM_GPI_SPI>, + <&gpi_dma0 1 0 QCOM_GPI_SPI>; + dma-names = "tx", "rx"; power-domains = <&rpmhpd SM8250_CX>; operating-points-v2 = <&qup_opp_table>; + #address-cells = <1>; + #size-cells = <0>; status = "disabled"; }; @@ -805,6 +847,9 @@ pinctrl-names = "default"; pinctrl-0 = <&qup_i2c1_default>; interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>, + <&gpi_dma0 1 1 QCOM_GPI_I2C>; + dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -816,10 +861,13 @@ clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>; interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; + dmas = <&gpi_dma0 0 1 QCOM_GPI_SPI>, + <&gpi_dma0 1 1 QCOM_GPI_SPI>; + dma-names = "tx", "rx"; power-domains = <&rpmhpd SM8250_CX>; operating-points-v2 = <&qup_opp_table>; + #address-cells = <1>; + #size-cells = <0>; status = "disabled"; }; @@ -831,6 +879,9 @@ pinctrl-names = "default"; pinctrl-0 = <&qup_i2c2_default>; interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>, + <&gpi_dma0 1 2 QCOM_GPI_I2C>; + dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -842,10 +893,13 @@ clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>; interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; + dmas = <&gpi_dma0 0 2 QCOM_GPI_SPI>, + <&gpi_dma0 1 2 QCOM_GPI_SPI>; + dma-names = "tx", "rx"; power-domains = <&rpmhpd SM8250_CX>; operating-points-v2 = <&qup_opp_table>; + #address-cells = <1>; + #size-cells = <0>; status = "disabled"; }; @@ -870,6 +924,9 @@ pinctrl-names = "default"; pinctrl-0 = <&qup_i2c3_default>; interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&gpi_dma0 0 3 QCOM_GPI_I2C>, + <&gpi_dma0 1 3 QCOM_GPI_I2C>; + dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -881,10 +938,13 @@ clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>; interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; + dmas = <&gpi_dma0 0 3 QCOM_GPI_SPI>, + <&gpi_dma0 1 3 QCOM_GPI_SPI>; + dma-names = "tx", "rx"; power-domains = <&rpmhpd SM8250_CX>; operating-points-v2 = <&qup_opp_table>; + #address-cells = <1>; + #size-cells = <0>; status = "disabled"; }; @@ -896,6 +956,9 @@ pinctrl-names = "default"; pinctrl-0 = <&qup_i2c4_default>; interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&gpi_dma0 0 4 QCOM_GPI_I2C>, + <&gpi_dma0 1 4 QCOM_GPI_I2C>; + dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -907,10 +970,13 @@ clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>; interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; + dmas = <&gpi_dma0 0 4 QCOM_GPI_SPI>, + <&gpi_dma0 1 4 QCOM_GPI_SPI>; + dma-names = "tx", "rx"; power-domains = <&rpmhpd SM8250_CX>; operating-points-v2 = <&qup_opp_table>; + #address-cells = <1>; + #size-cells = <0>; status = "disabled"; }; @@ -922,6 +988,9 @@ pinctrl-names = "default"; pinctrl-0 = <&qup_i2c5_default>; interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&gpi_dma0 0 5 QCOM_GPI_I2C>, + <&gpi_dma0 1 5 QCOM_GPI_I2C>; + dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -933,10 +1002,13 @@ clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>; interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; + dmas = <&gpi_dma0 0 5 QCOM_GPI_SPI>, + <&gpi_dma0 1 5 QCOM_GPI_SPI>; + dma-names = "tx", "rx"; power-domains = <&rpmhpd SM8250_CX>; operating-points-v2 = <&qup_opp_table>; + #address-cells = <1>; + #size-cells = <0>; status = "disabled"; }; @@ -948,6 +1020,9 @@ pinctrl-names = "default"; pinctrl-0 = <&qup_i2c6_default>; interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&gpi_dma0 0 6 QCOM_GPI_I2C>, + <&gpi_dma0 1 6 QCOM_GPI_I2C>; + dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -959,10 +1034,13 @@ clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>; interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; + dmas = <&gpi_dma0 0 6 QCOM_GPI_SPI>, + <&gpi_dma0 1 6 QCOM_GPI_SPI>; + dma-names = "tx", "rx"; power-domains = <&rpmhpd SM8250_CX>; operating-points-v2 = <&qup_opp_table>; + #address-cells = <1>; + #size-cells = <0>; status = "disabled"; }; @@ -987,6 +1065,9 @@ pinctrl-names = "default"; pinctrl-0 = <&qup_i2c7_default>; interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&gpi_dma0 0 7 QCOM_GPI_I2C>, + <&gpi_dma0 1 7 QCOM_GPI_I2C>; + dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -998,10 +1079,13 @@ clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>; interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; + dmas = <&gpi_dma0 0 7 QCOM_GPI_SPI>, + <&gpi_dma0 1 7 QCOM_GPI_SPI>; + dma-names = "tx", "rx"; power-domains = <&rpmhpd SM8250_CX>; operating-points-v2 = <&qup_opp_table>; + #address-cells = <1>; + #size-cells = <0>; status = "disabled"; }; }; @@ -1046,6 +1130,9 @@ pinctrl-names = "default"; pinctrl-0 = <&qup_i2c8_default>; interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&gpi_dma1 0 0 QCOM_GPI_I2C>, + <&gpi_dma1 1 0 QCOM_GPI_I2C>; + dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -1057,10 +1144,13 @@ clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>; interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; + dmas = <&gpi_dma1 0 0 QCOM_GPI_SPI>, + <&gpi_dma1 1 0 QCOM_GPI_SPI>; + dma-names = "tx", "rx"; power-domains = <&rpmhpd SM8250_CX>; operating-points-v2 = <&qup_opp_table>; + #address-cells = <1>; + #size-cells = <0>; status = "disabled"; }; @@ -1072,6 +1162,9 @@ pinctrl-names = "default"; pinctrl-0 = <&qup_i2c9_default>; interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&gpi_dma1 0 1 QCOM_GPI_I2C>, + <&gpi_dma1 1 1 QCOM_GPI_I2C>; + dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -1083,10 +1176,13 @@ clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>; interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; + dmas = <&gpi_dma1 0 1 QCOM_GPI_SPI>, + <&gpi_dma1 1 1 QCOM_GPI_SPI>; + dma-names = "tx", "rx"; power-domains = <&rpmhpd SM8250_CX>; operating-points-v2 = <&qup_opp_table>; + #address-cells = <1>; + #size-cells = <0>; status = "disabled"; }; @@ -1098,6 +1194,9 @@ pinctrl-names = "default"; pinctrl-0 = <&qup_i2c10_default>; interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&gpi_dma1 0 2 QCOM_GPI_I2C>, + <&gpi_dma1 1 2 QCOM_GPI_I2C>; + dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -1109,10 +1208,13 @@ clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>; interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; + dmas = <&gpi_dma1 0 2 QCOM_GPI_SPI>, + <&gpi_dma1 1 2 QCOM_GPI_SPI>; + dma-names = "tx", "rx"; power-domains = <&rpmhpd SM8250_CX>; operating-points-v2 = <&qup_opp_table>; + #address-cells = <1>; + #size-cells = <0>; status = "disabled"; }; @@ -1124,6 +1226,9 @@ pinctrl-names = "default"; pinctrl-0 = <&qup_i2c11_default>; interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&gpi_dma1 0 3 QCOM_GPI_I2C>, + <&gpi_dma1 1 3 QCOM_GPI_I2C>; + dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -1135,10 +1240,13 @@ clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>; interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; + dmas = <&gpi_dma1 0 3 QCOM_GPI_SPI>, + <&gpi_dma1 1 3 QCOM_GPI_SPI>; + dma-names = "tx", "rx"; power-domains = <&rpmhpd SM8250_CX>; operating-points-v2 = <&qup_opp_table>; + #address-cells = <1>; + #size-cells = <0>; status = "disabled"; }; @@ -1150,6 +1258,9 @@ pinctrl-names = "default"; pinctrl-0 = <&qup_i2c12_default>; interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&gpi_dma1 0 4 QCOM_GPI_I2C>, + <&gpi_dma1 1 4 QCOM_GPI_I2C>; + dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -1161,10 +1272,13 @@ clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>; interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; + dmas = <&gpi_dma1 0 4 QCOM_GPI_SPI>, + <&gpi_dma1 1 4 QCOM_GPI_SPI>; + dma-names = "tx", "rx"; power-domains = <&rpmhpd SM8250_CX>; operating-points-v2 = <&qup_opp_table>; + #address-cells = <1>; + #size-cells = <0>; status = "disabled"; }; @@ -1189,6 +1303,9 @@ pinctrl-names = "default"; pinctrl-0 = <&qup_i2c13_default>; interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&gpi_dma1 0 5 QCOM_GPI_I2C>, + <&gpi_dma1 1 5 QCOM_GPI_I2C>; + dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -1200,10 +1317,13 @@ clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>; interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; + dmas = <&gpi_dma1 0 5 QCOM_GPI_SPI>, + <&gpi_dma1 1 5 QCOM_GPI_SPI>; + dma-names = "tx", "rx"; power-domains = <&rpmhpd SM8250_CX>; operating-points-v2 = <&qup_opp_table>; + #address-cells = <1>; + #size-cells = <0>; status = "disabled"; }; }; @@ -2210,7 +2330,7 @@ <&gcc GCC_USB3_PHY_SEC_BCR>; reset-names = "phy", "common"; - usb_2_ssphy: lane@88eb200 { + usb_2_ssphy: lanes@88eb200 { reg = <0 0x088eb200 0 0x200>, <0 0x088eb400 0 0x200>, <0 0x088eb800 0 0x800>; @@ -2321,7 +2441,7 @@ resets = <&gcc GCC_USB30_PRIM_BCR>; - usb_1_dwc3: dwc3@a600000 { + usb_1_dwc3: usb@a600000 { compatible = "snps,dwc3"; reg = <0 0x0a600000 0 0xcd00>; interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; @@ -2372,7 +2492,7 @@ resets = <&gcc GCC_USB30_SEC_BCR>; - usb_2_dwc3: dwc3@a800000 { + usb_2_dwc3: usb@a800000 { compatible = "snps,dwc3"; reg = <0 0x0a800000 0 0xcd00>; interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; @@ -2470,10 +2590,9 @@ power-domains = <&dispcc MDSS_GDSC>; clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, - <&gcc GCC_DISP_HF_AXI_CLK>, <&gcc GCC_DISP_SF_AXI_CLK>, <&dispcc DISP_CC_MDSS_MDP_CLK>; - clock-names = "iface", "bus", "nrt_bus", "core"; + clock-names = "iface", "nrt_bus", "core"; assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>; assigned-clock-rates = <460000000>; @@ -2578,6 +2697,9 @@ "iface", "bus"; + assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>; + assigned-clock-parents = <&dsi0_phy 0>, <&dsi0_phy 1>; + operating-points-v2 = <&dsi_opp_table>; power-domains = <&rpmhpd SM8250_MMCX>; @@ -2648,6 +2770,9 @@ "iface", "bus"; + assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK1_CLK_SRC>; + assigned-clock-parents = <&dsi1_phy 0>, <&dsi1_phy 1>; + operating-points-v2 = <&dsi_opp_table>; power-domains = <&rpmhpd SM8250_MMCX>; @@ -3955,7 +4080,7 @@ }; }; - epss_l3: interconnect@18591000 { + epss_l3: interconnect@18590000 { compatible = "qcom,sm8250-epss-l3"; reg = <0 0x18590000 0 0x1000>; diff --git a/dts/src/arm64/qcom/sm8350-hdk.dts b/dts/src/arm64/qcom/sm8350-hdk.dts index f23a0cf3f7..56093e260d 100644 --- a/dts/src/arm64/qcom/sm8350-hdk.dts +++ b/dts/src/arm64/qcom/sm8350-hdk.dts @@ -219,7 +219,7 @@ firmware-name = "qcom/sm8350/modem.mbn"; }; -&qupv3_id_1 { +&qupv3_id_0 { status = "okay"; }; diff --git a/dts/src/arm64/qcom/sm8350-mtp.dts b/dts/src/arm64/qcom/sm8350-mtp.dts index 93740444dd..bd95009c18 100644 --- a/dts/src/arm64/qcom/sm8350-mtp.dts +++ b/dts/src/arm64/qcom/sm8350-mtp.dts @@ -286,7 +286,7 @@ firmware-name = "qcom/sm8350/modem.mbn"; }; -&qupv3_id_1 { +&qupv3_id_0 { status = "okay"; }; diff --git a/dts/src/arm64/qcom/sm8350.dtsi b/dts/src/arm64/qcom/sm8350.dtsi index 0d16392bb9..e91cd8a5e5 100644 --- a/dts/src/arm64/qcom/sm8350.dtsi +++ b/dts/src/arm64/qcom/sm8350.dtsi @@ -456,7 +456,7 @@ #mbox-cells = <2>; }; - qupv3_id_1: geniqup@9c0000 { + qupv3_id_0: geniqup@9c0000 { compatible = "qcom,geni-se-qup"; reg = <0x0 0x009c0000 0x0 0x6000>; clock-names = "m-ahb", "s-ahb"; @@ -481,6 +481,31 @@ }; }; + qupv3_id_1: geniqup@ac0000 { + compatible = "qcom,geni-se-qup"; + reg = <0x0 0x00ac0000 0x0 0x6000>; + clock-names = "m-ahb", "s-ahb"; + clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>, + <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + status = "disabled"; + + i2c13: i2c@a94000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00a94000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c13_default_state>; + interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + }; + apps_smmu: iommu@15000000 { compatible = "qcom,sm8350-smmu-500", "arm,mmu-500"; reg = <0 0x15000000 0 0x100000>; @@ -666,12 +691,10 @@ clocks = <&rpmhcc RPMH_IPA_CLK>; clock-names = "core"; - interconnects = <&aggre2_noc MASTER_IPA &gem_noc SLAVE_LLCC>, - <&mc_virt MASTER_LLCC &mc_virt SLAVE_EBI1>, + interconnects = <&aggre2_noc MASTER_IPA &mc_virt SLAVE_EBI1>, <&gem_noc MASTER_APPSS_PROC &config_noc SLAVE_IPA_CFG>; - interconnect-names = "ipa_to_llcc", - "llcc_to_ebi1", - "appss_to_ipa"; + interconnect-names = "memory", + "config"; qcom,smem-states = <&ipa_smp2p_out 0>, <&ipa_smp2p_out 1>; @@ -801,6 +824,7 @@ interrupt-controller; #interrupt-cells = <2>; gpio-ranges = <&tlmm 0 0 204>; + wakeup-parent = <&pdc>; qup_uart3_default_state: qup-uart3-default-state { rx { @@ -812,6 +836,19 @@ function = "qup3"; }; }; + + qup_i2c13_default_state: qup-i2c13-default-state { + mux { + pins = "gpio0", "gpio1"; + function = "qup13"; + }; + + config { + pins = "gpio0", "gpio1"; + drive-strength = <2>; + bias-pull-up; + }; + }; }; rng: rng@10d3000 { @@ -1273,7 +1310,7 @@ resets = <&gcc GCC_USB30_PRIM_BCR>; - usb_1_dwc3: dwc3@a600000 { + usb_1_dwc3: usb@a600000 { compatible = "snps,dwc3"; reg = <0 0x0a600000 0 0xcd00>; interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; @@ -1317,7 +1354,7 @@ resets = <&gcc GCC_USB30_SEC_BCR>; - usb_2_dwc3: dwc3@a800000 { + usb_2_dwc3: usb@a800000 { compatible = "snps,dwc3"; reg = <0 0x0a800000 0 0xcd00>; interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; |