diff options
Diffstat (limited to 'dts/src/arm64/xilinx/zynqmp-zcu104-revA.dts')
-rw-r--r-- | dts/src/arm64/xilinx/zynqmp-zcu104-revA.dts | 292 |
1 files changed, 282 insertions, 10 deletions
diff --git a/dts/src/arm64/xilinx/zynqmp-zcu104-revA.dts b/dts/src/arm64/xilinx/zynqmp-zcu104-revA.dts index 5637e1c17f..bd8f20f322 100644 --- a/dts/src/arm64/xilinx/zynqmp-zcu104-revA.dts +++ b/dts/src/arm64/xilinx/zynqmp-zcu104-revA.dts @@ -2,7 +2,7 @@ /* * dts file for Xilinx ZynqMP ZCU104 * - * (C) Copyright 2017 - 2019, Xilinx, Inc. + * (C) Copyright 2017 - 2021, Xilinx, Inc. * * Michal Simek <michal.simek@xilinx.com> */ @@ -12,6 +12,7 @@ #include "zynqmp.dtsi" #include "zynqmp-clk-ccf.dtsi" #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/pinctrl/pinctrl-zynqmp.h> #include <dt-bindings/phy/phy.h> / { @@ -22,10 +23,13 @@ ethernet0 = &gem3; i2c0 = &i2c1; mmc0 = &sdhci1; + nvmem0 = &eeprom; rtc0 = &rtc; serial0 = &uart0; serial1 = &uart1; serial2 = &dcc; + spi0 = &qspi; + usb0 = &usb0; }; chosen { @@ -59,16 +63,52 @@ &can1 { status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can1_default>; }; &dcc { status = "okay"; }; +&fpd_dma_chan1 { + status = "okay"; +}; + +&fpd_dma_chan2 { + status = "okay"; +}; + +&fpd_dma_chan3 { + status = "okay"; +}; + +&fpd_dma_chan4 { + status = "okay"; +}; + +&fpd_dma_chan5 { + status = "okay"; +}; + +&fpd_dma_chan6 { + status = "okay"; +}; + +&fpd_dma_chan7 { + status = "okay"; +}; + +&fpd_dma_chan8 { + status = "okay"; +}; + &gem3 { status = "okay"; phy-handle = <&phy0>; phy-mode = "rgmii-id"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gem3_default>; phy0: ethernet-phy@c { reg = <0xc>; ti,rx-internal-delay = <0x8>; @@ -85,6 +125,11 @@ &i2c1 { status = "okay"; clock-frequency = <400000>; + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&pinctrl_i2c1_default>; + pinctrl-1 = <&pinctrl_i2c1_gpio>; + scl-gpios = <&gpio 16 GPIO_ACTIVE_HIGH>; + sda-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; /* Another connection to this bus via PL i2c via PCA9306 - u45 */ i2c-mux@74 { /* u34 */ @@ -104,7 +149,7 @@ * 512B - 768B address 0x56 * 768B - 1024B address 0x57 */ - eeprom@54 { /* u23 */ + eeprom: eeprom@54 { /* u23 */ compatible = "atmel,24c08"; reg = <0x54>; #address-cells = <1>; @@ -116,20 +161,20 @@ #address-cells = <1>; #size-cells = <0>; reg = <1>; - clock_8t49n287: clock-generator@6c { /* 8T49N287 - u182 */ - reg = <0x6c>; - }; + /* 8T49N287 - u182 */ }; i2c@2 { #address-cells = <1>; #size-cells = <0>; reg = <2>; - irps5401_43: irps54012@43 { /* IRPS5401 - u175 */ - reg = <0x43>; + irps5401_43: irps5401@43 { /* IRPS5401 - u175 */ + compatible = "infineon,irps5401"; + reg = <0x43>; /* pmbus / i2c 0x13 */ }; - irps5401_4d: irps54012@4d { /* IRPS5401 - u180 */ - reg = <0x4d>; + irps5401_44: irps5401@44 { /* IRPS5401 - u180 */ + compatible = "infineon,irps5401"; + reg = <0x44>; /* pmbus / i2c 0x14 */ }; }; @@ -173,8 +218,202 @@ }; }; -&rtc { +&pinctrl0 { status = "okay"; + + pinctrl_can1_default: can1-default { + mux { + function = "can1"; + groups = "can1_6_grp"; + }; + + conf { + groups = "can1_6_grp"; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + drive-strength = <12>; + }; + + conf-rx { + pins = "MIO25"; + bias-high-impedance; + }; + + conf-tx { + pins = "MIO24"; + bias-disable; + }; + }; + + pinctrl_i2c1_default: i2c1-default { + mux { + groups = "i2c1_4_grp"; + function = "i2c1"; + }; + + conf { + groups = "i2c1_4_grp"; + bias-pull-up; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + drive-strength = <12>; + }; + }; + + pinctrl_i2c1_gpio: i2c1-gpio { + mux { + groups = "gpio0_16_grp", "gpio0_17_grp"; + function = "gpio0"; + }; + + conf { + groups = "gpio0_16_grp", "gpio0_17_grp"; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + drive-strength = <12>; + }; + }; + + pinctrl_gem3_default: gem3-default { + mux { + function = "ethernet3"; + groups = "ethernet3_0_grp"; + }; + + conf { + groups = "ethernet3_0_grp"; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + drive-strength = <12>; + }; + + conf-rx { + pins = "MIO70", "MIO71", "MIO72", "MIO73", "MIO74", + "MIO75"; + bias-high-impedance; + low-power-disable; + }; + + conf-tx { + pins = "MIO64", "MIO65", "MIO66", "MIO67", "MIO68", + "MIO69"; + bias-disable; + low-power-enable; + }; + + mux-mdio { + function = "mdio3"; + groups = "mdio3_0_grp"; + }; + + conf-mdio { + groups = "mdio3_0_grp"; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + bias-disable; + }; + }; + + pinctrl_sdhci1_default: sdhci1-default { + mux { + groups = "sdio1_0_grp"; + function = "sdio1"; + }; + + conf { + groups = "sdio1_0_grp"; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + bias-disable; + drive-strength = <12>; + }; + + mux-cd { + groups = "sdio1_cd_0_grp"; + function = "sdio1_cd"; + }; + + conf-cd { + groups = "sdio1_cd_0_grp"; + bias-high-impedance; + bias-pull-up; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + }; + }; + + pinctrl_uart0_default: uart0-default { + mux { + groups = "uart0_4_grp"; + function = "uart0"; + }; + + conf { + groups = "uart0_4_grp"; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + drive-strength = <12>; + }; + + conf-rx { + pins = "MIO18"; + bias-high-impedance; + }; + + conf-tx { + pins = "MIO19"; + bias-disable; + }; + }; + + pinctrl_uart1_default: uart1-default { + mux { + groups = "uart1_5_grp"; + function = "uart1"; + }; + + conf { + groups = "uart1_5_grp"; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + drive-strength = <12>; + }; + + conf-rx { + pins = "MIO21"; + bias-high-impedance; + }; + + conf-tx { + pins = "MIO20"; + bias-disable; + }; + }; + + pinctrl_usb0_default: usb0-default { + mux { + groups = "usb0_0_grp"; + function = "usb0"; + }; + + conf { + groups = "usb0_0_grp"; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + drive-strength = <12>; + }; + + conf-rx { + pins = "MIO52", "MIO53", "MIO55"; + bias-high-impedance; + }; + + conf-tx { + pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59", + "MIO60", "MIO61", "MIO62", "MIO63"; + bias-disable; + }; + }; }; &psgtr { @@ -184,6 +423,23 @@ clock-names = "ref1", "ref2", "ref3"; }; +&qspi { + status = "okay"; + flash@0 { + compatible = "m25p80", "jedec,spi-nor"; /* n25q512a 128MiB */ + #address-cells = <1>; + #size-cells = <1>; + reg = <0x0>; + spi-tx-bus-width = <1>; + spi-rx-bus-width = <4>; + spi-max-frequency = <108000000>; /* Based on DC1 spec */ + }; +}; + +&rtc { + status = "okay"; +}; + &sata { status = "okay"; /* SATA OOB timing settings */ @@ -203,22 +459,38 @@ &sdhci1 { status = "okay"; no-1-8-v; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sdhci1_default>; xlnx,mio-bank = <1>; disable-wp; }; &uart0 { status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart0_default>; }; &uart1 { status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1_default>; }; /* ULPI SMSC USB3320 */ &usb0 { status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb0_default>; + phy-names = "usb3-phy"; + phys = <&psgtr 2 PHY_TYPE_USB3 0 2>; +}; + +&dwc3_0 { + status = "okay"; dr_mode = "host"; + snps,usb3_lpm_capable; + maximum-speed = "super-speed"; }; &watchdog0 { |