diff options
Diffstat (limited to 'dts/src/arm64/xilinx/zynqmp-zcu106-revA.dts')
| -rw-r--r-- | dts/src/arm64/xilinx/zynqmp-zcu106-revA.dts | 65 |
1 files changed, 50 insertions, 15 deletions
diff --git a/dts/src/arm64/xilinx/zynqmp-zcu106-revA.dts b/dts/src/arm64/xilinx/zynqmp-zcu106-revA.dts index 20b7c75bb1..50c384aa25 100644 --- a/dts/src/arm64/xilinx/zynqmp-zcu106-revA.dts +++ b/dts/src/arm64/xilinx/zynqmp-zcu106-revA.dts @@ -2,9 +2,10 @@ /* * dts file for Xilinx ZynqMP ZCU106 * - * (C) Copyright 2016 - 2021, Xilinx, Inc. + * (C) Copyright 2016 - 2022, Xilinx, Inc. + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc. * - * Michal Simek <michal.simek@xilinx.com> + * Michal Simek <michal.simek@amd.com> */ /dts-v1/; @@ -47,7 +48,7 @@ gpio-keys { compatible = "gpio-keys"; autorepeat; - sw19 { + switch-19 { label = "sw19"; gpios = <&gpio 22 GPIO_ACTIVE_HIGH>; linux,code = <KEY_DOWN>; @@ -150,6 +151,18 @@ #clock-cells = <0>; clock-frequency = <114285000>; }; + + dpcon { + compatible = "dp-connector"; + label = "P11"; + type = "full-size"; + + port { + dpcon_in: endpoint { + remote-endpoint = <&dpsub_dp_out>; + }; + }; + }; }; &can1 { @@ -200,12 +213,19 @@ phy-mode = "rgmii-id"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_gem3_default>; - phy0: ethernet-phy@c { - reg = <0xc>; - ti,rx-internal-delay = <0x8>; - ti,tx-internal-delay = <0xa>; - ti,fifo-depth = <0x1>; - ti,dp83867-rxctrl-strap-quirk; + mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@c { + #phy-cells = <1>; + reg = <0xc>; + compatible = "ethernet-phy-id2000.a231"; + ti,rx-internal-delay = <0x8>; + ti,tx-internal-delay = <0xa>; + ti,fifo-depth = <0x1>; + ti,dp83867-rxctrl-strap-quirk; + reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; + }; }; }; @@ -215,14 +235,18 @@ pinctrl-0 = <&pinctrl_gpio_default>; }; +&gpu { + status = "okay"; +}; + &i2c0 { status = "okay"; clock-frequency = <400000>; pinctrl-names = "default", "gpio"; pinctrl-0 = <&pinctrl_i2c0_default>; pinctrl-1 = <&pinctrl_i2c0_gpio>; - scl-gpios = <&gpio 14 GPIO_ACTIVE_HIGH>; - sda-gpios = <&gpio 15 GPIO_ACTIVE_HIGH>; + scl-gpios = <&gpio 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + sda-gpios = <&gpio 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; tca6416_u97: gpio@20 { compatible = "ti,tca6416"; @@ -484,8 +508,8 @@ pinctrl-names = "default", "gpio"; pinctrl-0 = <&pinctrl_i2c1_default>; pinctrl-1 = <&pinctrl_i2c1_gpio>; - scl-gpios = <&gpio 16 GPIO_ACTIVE_HIGH>; - sda-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; + scl-gpios = <&gpio 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + sda-gpios = <&gpio 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; /* PL i2c via PCA9306 - u45 */ i2c-mux@74 { /* u34 */ @@ -770,19 +794,22 @@ conf { groups = "usb0_0_grp"; - slew-rate = <SLEW_RATE_SLOW>; power-source = <IO_STANDARD_LVCMOS18>; }; conf-rx { pins = "MIO52", "MIO53", "MIO55"; bias-high-impedance; + drive-strength = <12>; + slew-rate = <SLEW_RATE_FAST>; }; conf-tx { pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59", "MIO60", "MIO61", "MIO62", "MIO63"; bias-disable; + drive-strength = <4>; + slew-rate = <SLEW_RATE_SLOW>; }; }; @@ -937,7 +964,7 @@ #address-cells = <1>; #size-cells = <1>; reg = <0x0>; - spi-tx-bus-width = <1>; + spi-tx-bus-width = <4>; spi-rx-bus-width = <4>; /* FIXME also DUAL configuration possible */ spi-max-frequency = <108000000>; /* Based on DC1 spec */ }; @@ -1015,4 +1042,12 @@ phy-names = "dp-phy0", "dp-phy1"; phys = <&psgtr 1 PHY_TYPE_DP 0 3>, <&psgtr 0 PHY_TYPE_DP 1 3>; + + ports { + port@5 { + dpsub_dp_out: endpoint { + remote-endpoint = <&dpcon_in>; + }; + }; + }; }; |