diff options
Diffstat (limited to 'include/configs/TOP5200.h')
| -rw-r--r-- | include/configs/TOP5200.h | 405 |
1 files changed, 0 insertions, 405 deletions
diff --git a/include/configs/TOP5200.h b/include/configs/TOP5200.h deleted file mode 100644 index e44dde5424..0000000000 --- a/include/configs/TOP5200.h +++ /dev/null @@ -1,405 +0,0 @@ -/* - * (C) Copyright 2003 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * modified for TOP5200-series by Reinhard Meyer, www.emk-elektronik.de - * - * TOP5200 differences from IceCube: - * 1 FLASH Bank for one Chip only, up to 64 MB in 16 MB Banks - * bank switch controlled by TIMER_6(LSB) and TIMER_7(MSB) Pins - * 1 SDRAM/DDRAM Bank up to 256 MB - * local VPD I2C Bus is software driven and uses - * GPIO_WKUP_6 for SDA, GPIO_WKUP_7 for SCL - * FLASH is re-located at 0xff000000 - * Internal regs are at 0xf0000000 - * Reset jumps to 0x00000100 - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ -#define CONFIG_MPC5200 1 /* More exactly a MPC5200 */ -#define CONFIG_TOP5200 1 /* ... on TOP5200 board - we need this for FEC.C */ - -#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ - -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) -# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/* - * Serial console configuration - */ -#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ -#define CONFIG_BAUDRATE 9600 /* ... at 9600 bps */ -#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - - -#if defined (CONFIG_EVAL5200) || defined (CONFIG_LITE5200) -/* - * PCI Mapping: - * 0x40000000 - 0x4fffffff - PCI Memory - * 0x50000000 - 0x50ffffff - PCI IO Space - */ -# define CONFIG_PCI 1 -# define CONFIG_PCI_PNP 1 -# define CONFIG_PCI_SCAN_SHOW 1 - -# define CONFIG_PCI_MEM_BUS 0x40000000 -# define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS -# define CONFIG_PCI_MEM_SIZE 0x10000000 - -# define CONFIG_PCI_IO_BUS 0x50000000 -# define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS -# define CONFIG_PCI_IO_SIZE 0x01000000 - -# define ADD_PCI_CMD CFG_CMD_PCI - -#else /* no Evaluation board */ - -# define ADD_PCI_CMD 0 /* no CFG_CMD_PCI */ - -#endif - -/* USB */ -#if defined (CONFIG_EVAL5200) || defined (CONFIG_LITE5200) - -# define CONFIG_USB_OHCI -# define CONFIG_USB_CLOCK 0x0001bbbb -# if defined (CONFIG_EVAL5200) -# define CONFIG_USB_CONFIG 0x00005100 -# else -# define CONFIG_USB_CONFIG 0x00001000 -# endif -# define ADD_USB_CMD CFG_CMD_USB | CFG_CMD_FAT -# define CONFIG_DOS_PARTITION -# define CONFIG_USB_STORAGE - -#else - -# define ADD_USB_CMD 0 - -#endif - -/* IDE */ -#if defined (CONFIG_EVAL5200) || defined (CONFIG_LITE5200) - -# define ADD_IDE_CMD CFG_CMD_IDE | CFG_CMD_FAT -# define CONFIG_DOS_PARTITION - -#else - -# define ADD_IDE_CMD 0 - -#endif - -/* - * Supported commands - */ -#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \ - ADD_PCI_CMD | \ - ADD_USB_CMD | \ - ADD_IDE_CMD | \ - CFG_CMD_ASKENV | \ - CFG_CMD_DATE | \ - CFG_CMD_DHCP | \ - CFG_CMD_I2C | \ - CFG_CMD_EEPROM | \ - CFG_CMD_REGINFO | \ - CFG_CMD_IMMAP | \ - CFG_CMD_ELF | \ - CFG_CMD_MII | \ - CFG_CMD_BEDBUG \ - ) - -/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ -#include <cmd_confdefs.h> - -/* - * MUST be low boot - HIGHBOOT is not supported anymore - */ -#if (TEXT_BASE == 0xFF000000) /* Boot low with 16 MB Flash */ -# define CFG_LOWBOOT 1 -# define CFG_LOWBOOT16 1 -#else -# error "TEXT_BASE must be 0xff000000" -#endif - -/* - * Autobooting - */ -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "flash_nfs=run nfsargs addip;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ - "rootpath=/opt/eldk/ppc_82xx\0" \ - "bootfile=/tftpboot/MPC5200/uImage\0" \ - "" - -#define CONFIG_BOOTCOMMAND "run flash_self" - -/* - * IPB Bus clocking configuration. - */ -#undef CFG_IPBSPEED_133 /* define for 133MHz speed */ - -/* - * I2C configuration - */ -/* - * EEPROM configuration - */ -#define CFG_EEPROM_PAGE_WRITE_BITS 3 -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 70 - -#define CFG_I2C_EEPROM_ADDR_LEN 2 -#define CFG_EEPROM_SIZE 0x2000 - -#define CONFIG_ENV_OVERWRITE -#define CONFIG_MISC_INIT_R - -#undef CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SOFT_I2C 1 /* I2C with softwate support */ - -#if defined (CONFIG_SOFT_I2C) -# define SDA0 0x40 -# define SCL0 0x80 -# define GPIOE0 *((volatile uchar*)(CFG_MBAR+0x0c00)) -# define DDR0 *((volatile uchar*)(CFG_MBAR+0x0c08)) -# define DVO0 *((volatile uchar*)(CFG_MBAR+0x0c0c)) -# define DVI0 *((volatile uchar*)(CFG_MBAR+0x0c20)) -# define ODE0 *((volatile uchar*)(CFG_MBAR+0x0c04)) -# define I2C_INIT {GPIOE0|=(SDA0|SCL0);ODE0|=(SDA0|SCL0);DVO0|=(SDA0|SCL0);DDR0|=(SDA0|SCL0);} -# define I2C_READ ((DVI0&SDA0)?1:0) -# define I2C_SDA(x) {if(x)DVO0|=SDA0;else DVO0&=~SDA0;} -# define I2C_SCL(x) {if(x)DVO0|=SCL0;else DVO0&=~SCL0;} -# define I2C_DELAY {udelay(5);} -# define I2C_ACTIVE {DDR0|=SDA0;} -# define I2C_TRISTATE {DDR0&=~SDA0;} -# define CFG_I2C_SPEED 100000 -# define CFG_I2C_SLAVE 0x7F -#define CFG_I2C_EEPROM_ADDR 0x57 -#define CFG_I2C_FACT_ADDR 0x57 -#endif - -#if defined (CONFIG_HARD_I2C) -# define CFG_I2C_MODULE 2 /* Select I2C module #1 or #2 */ -# define CFG_I2C_SPEED 100000 /* 100 kHz */ -# define CFG_I2C_SLAVE 0x7F -#define CFG_I2C_EEPROM_ADDR 0x54 -#define CFG_I2C_FACT_ADDR 0x54 -#endif - -/* - * Flash configuration, expect one 16 Megabyte Bank at most - */ -#define CFG_FLASH_BASE 0xff000000 -#define CFG_FLASH_SIZE 0x01000000 -#define CFG_MAX_FLASH_BANKS 1 /* max num of memory banks */ -#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0) - -#define CFG_MAX_FLASH_SECT 256 /* max num of sects on one chip */ - -#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ - -#undef CONFIG_FLASH_16BIT /* Flash is 8-bit */ - -/* - * DRAM configuration - will be read from VPD later... TODO! - */ -/* 2x MT48LC16M16A2 - 7.5 ns SDRAMS = 64 MegaBytes Total */ -#define CFG_DRAM_DDR 0 -#define CFG_DRAM_EMODE 0 -#define CFG_DRAM_MODE 0x00CD -#define CFG_DRAM_CONTROL 0x514F0000 -#define CFG_DRAM_CONFIG1 0xD2333A00 -#define CFG_DRAM_CONFIG2 0x8AD70004 -#define CFG_DRAM_TAP_DEL 0x08 -#define CFG_DRAM_RAM_SIZE 0x19 - -/* - * Environment settings - */ -#define CFG_ENV_IS_IN_EEPROM 1 /* turn on EEPROM env feature */ -#define CFG_ENV_OFFSET 0x1000 -#define CFG_ENV_SIZE 0x0700 - -/* - * VPD settings - */ -#define CFG_FACT_OFFSET 0x1800 -#define CFG_FACT_SIZE 0x0800 - -/* - * Memory map - * - * Warning!!! with the current BestComm Task, MBAR MUST BE set to 0xf0000000 - */ -#define CFG_MBAR 0xf0000000 /* DO NOT CHANGE this */ -#define CFG_SDRAM_BASE 0x00000000 -#define CFG_DEFAULT_MBAR 0x80000000 - -/* Use SRAM until RAM will be available */ -#define CFG_INIT_RAM_ADDR MPC5XXX_SRAM -#define CFG_INIT_RAM_END MPC5XXX_SRAM_SIZE /* End of used area in DPRAM */ - - -#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET - -#define CFG_MONITOR_BASE TEXT_BASE -#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) -# define CFG_RAMBOOT 1 -#endif - -#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Ethernet configuration - */ -#define CONFIG_MPC5xxx_FEC 1 -#define CONFIG_FEC_10MBIT 1 /* Workaround for FEC 100Mbit problem */ -#define CONFIG_PHY_ADDR 0x1f -#define CONFIG_PHY_TYPE 0x79c874 -/* - * GPIO configuration: - * PSC1,2,3 predefined as UART - * PCI disabled - * Ethernet 100 with MD - */ -#define CFG_GPS_PORT_CONFIG 0x00058044 - -/* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) -# define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -# define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x00100000 /* memtest works on */ -#define CFG_MEMTEST_END 0x01f00000 /* 1 ... 31 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x200000 /* default load address */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#ifdef CONFIG_EVAL5200 /* M48T08 is available with the Evaluation board only */ - #define CONFIG_RTC_MK48T59 1 /* use M48T08 on EVAL5200 */ - #define RTC(reg) (0xf0010000+reg) - /* setup CS2 for M48T08. Must MAP 64kB */ - #define CFG_CS2_START RTC(0) - #define CFG_CS2_SIZE 0x10000 - /* setup CS2 configuration register: */ - /* WaitP = 0, WaitX = 4, MX=0, AL=1, AA=1, CE=1 */ - /* AS=2, DS=0, Bank=0, WTyp=0, WS=0, RS=0, WO=0, RO=0 */ - #define CFG_CS2_CFG 0x00047800 -#else - #define CONFIG_RTC_MPC5200 1 /* use internal MPC5200 RTC */ -#endif - -/* - * Various low-level settings - */ -#define CFG_HID0_INIT HID0_ICE | HID0_ICFI -#define CFG_HID0_FINAL HID0_ICE - -#define CFG_BOOTCS_START CFG_FLASH_BASE -#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE -#define CFG_BOOTCS_CFG 0x00047801 -#define CFG_CS0_START CFG_FLASH_BASE -#define CFG_CS0_SIZE CFG_FLASH_SIZE - -#define CFG_CS_BURST 0x00000000 -#define CFG_CS_DEADCYCLE 0x33333333 - -#define CFG_RESET_ADDRESS 0x7f000000 - -/*----------------------------------------------------------------------- - * IDE/ATA stuff Supports IDE harddisk - *----------------------------------------------------------------------- - */ - -#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ - -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_LED /* LED for ide not supported */ - -#define CONFIG_IDE_RESET 1 -#define CONFIG_IDE_PREINIT - -#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ - -#define CFG_ATA_IDE0_OFFSET 0x0000 - -#define CFG_ATA_BASE_ADDR MPC5XXX_ATA - -/* Offset for data I/O */ -#define CFG_ATA_DATA_OFFSET (0x0060) - -/* Offset for normal register accesses */ -#define CFG_ATA_REG_OFFSET (CFG_ATA_DATA_OFFSET) - -/* Offset for alternate registers */ -#define CFG_ATA_ALT_OFFSET (0x005c) - -/* Interval between registers */ -#define CFG_ATA_STRIDE 4 - -#endif /* __CONFIG_H */ |