| Commit message (Collapse) | Author | Age | Files | Lines |
|\ |
|
| |
| |
| |
| |
| |
| |
| |
| | |
The STPMIC1 is the ST Microelectronics PMIC designed for use with
STM32MP. Enable it and its cell drivers by default in the defconfig.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| | |
We've had some new drivers added for the STM32MP since the defconfig was
first added. Include the newcomers.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|/
|
|
|
|
|
|
| |
The Arria10 DTS uses the state framework.
Enable the driver so it gets probed.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|\ |
|
| |
| |
| |
| |
| |
| |
| | |
Merge the defconfigs for the i.MX23 boards into a common
imx23_defconfig.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| | |
Merge the defconfigs for the i.MX28 boards into a common
imx28_defconfig.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|\ \ |
|
| |/
| |
| |
| |
| |
| |
| | |
Have it compile as part of the defconfig, to improve coverage.
Signed-off-by: Ahmad Fatoum <ahmad@a3f.at>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| | |
We can build multiple DTBs into the binary and board code can select
which one to use. Drop the single builtin DTB and let the boards using
it pass the correct one.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| | |
NETX support has been removed from the Kernel, so there's no point in
supporting it in barebox any longer. Remove the architecture.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| | |
The TX53STK5 is covered by the imx_v7_defconfig, so remove the board
specific config file.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| | |
The TQMA53 is covered by the imx_v7_defconfig, so remove the board
specific config file.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| | |
The edm-qmx6 is covered by the imx_v7_defconfig, so remove the board
specific config.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|/
|
|
|
|
|
| |
The vincell Board is covered by the imx_v7_defconfig. Remove the board
specific config.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
|
|
|
|
|
|
|
| |
- switch the i.MX1 based scb9328 board to device tree
- Remove scb9328_defconfig and enable scb9328 board support in
imx_defconfig
- Remove old environment and switch to new default environment
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
|
|
|
| |
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|\ |
|
| |
| |
| |
| |
| |
| |
| |
| | |
Now with pinctrl/GPIO support, enable some useful GPIO-related
drivers and commands.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| | |
With the IWDG driver implemented in barebox, have it be part of the
default configuration.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| | |
This saves 23K with my configuration (from 250K to 227K).
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Serial and clk driver both depend on CONFIG_ARCH_STM32MP1,
so either the Kconfig symbol or their depend needs to change.
Patches posted by the vendor to Linux, U-Boot and their BSP
Yocto-Layer speak of a STM32MP-Family of which the STM32MP1
is the first series, thus rename the arch by dropping the 1.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Update defconfig files with the following script.
for a in arch/*; do
arch=$(basename $a)
for c in $a/configs/*; do
config=$(basename $c)
export ARCH=$arch
make $config && make savedefconfig && mv defconfig $c
done
done
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
|
|
|
|
|
|
|
|
|
| |
The "Primary Protected Application" (PPA) is a PSCI compliant firmware
distributed by NXP. It is needed to start the secondary cores on
Layerscape SoCs. Without it Linux will be started in EL3 and doesn't
work properly. The precompiled firmware images can be found on
https://github.com/NXP/qoriq-ppa-binary and are not included in
barebox.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|\ |
|
| |
| |
| |
| |
| |
| | |
Enable remaining boards and enable some more features.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|\ \ |
|
| |/
| |
| |
| |
| | |
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|/
|
|
|
|
|
|
| |
The TQMLS1046a has an i2c mux and a i2c gpio expander. Add support for
it and also disable early debugging as these are for a single board
only.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|\ |
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This adds initial STMicroelectronics MP1 support along with support
for the DK2 devel board. Only very basic support:
- UART
- SDRAM memory base/size
- No 1st stage support
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|\ \ |
|
| |/
| |
| |
| | |
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The current defaultenv-kindle-mx50 requires MCI_STARTUP to boot the installed
linux. CMD_LOADY is mentioned in the doc for barebox update purposes.
FS_EXT4, FS_FAT and FS_FAT_WRITE gives users file system access. Also enable
CMD_MEMTEST, CMD_CLK, CMD_REGULATOR and CMD_EDIT for interested users.
The extended image will consume 195kB of available 253kB.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|/
|
|
|
|
|
| |
With the MMU enabled, a memtest runs 14 times faster.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|\ |
|
| |
| |
| |
| |
| |
| | |
Required for emmc pin function switching on Raspberry Pi 3.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
| |
| |
| |
| | |
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|\ \ |
|
| |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
For platforms such as the at91, the boot ROM imposes an upper limit
on barebox file size. Prior to 5a1a5ed253 ("ARM: images: use piggydata"),
BAREBOX_MAX_PBLX_SIZE seems to have been the way to go for limiting
the size of the final barebox binary when using the PBL.
With pblx removed, this variable is of no use, so have the existing
BAREBOX_MAX_IMAGE_SIZE replace its functionality.
Currently BAREBOX_MAX_IMAGE_SIZE is only checked against in the non-PBL
case, so add a check in the PBL case as well.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|/
|
|
|
|
|
|
|
|
|
|
|
|
| |
The phyCORE-i.MX8M aka PCL-066 is a SoM containing a i.MX8M SoC.
phyCORE-i.MX8M:
- 1GB LPDDR4 RAM
- eMMC
- microSD
- Ethernet
Signed-off-by: Christian Hemp <christian.hemp@posteo.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|\ |
|
| |
| |
| |
| |
| |
| |
| |
| | |
Since the 16550 driver now supports the RPI3 miniuart, enable it in the default
config.
Signed-off-by: Rouven Czerwinski <r.czerwinski@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|\ \ |
|
| |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Add support for the following ZII i.MX8MQ based boards:
- ZII i.MX8MQ RMB3
- ZII i.MX8MQ Zest
Most of the basic peripherals are supported by this patch. More
advanced features such as PCIe, display support, etc, are planned to
be added later.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
| |
| |
| |
| |
| | |
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|/
|
|
|
| |
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|\ |
|
| |
| |
| |
| |
| | |
Signed-off-by: Thomas Haemmerle <thomas.haemmerle@wolfvision.net>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Add support for the Xilinx Zynq Ultrascale+ MPSoC architecture (ZynqMP)
and the Xilinx ZCU104 board.
Barebox is booted as BL33 in EL-1 and expects that a BL2 (i.e. the FSBL)
already took care of initializing the RAM. Also for debug_ll, the UART
is expected to be already setup correctly. Thus, you have to add the
Barebox binary to a boot image as described in "Chapter 11: Boot and
Configuration" of "Zynq Ultrascale+ Device Technical Reference Manual".
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|