| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
| |
Use stdout-path instead of linux,stdout-path and use &uart format
instead of writing the full path.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
|
|
| |
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
|
|
|
|
|
|
|
|
|
|
| |
tested on i.MX53 START-R :
barebox@Freescale i.MX53 Quick Start-R Board:/ ata0.probe=1
imx-sata 10000000.sata: port 0: SATA link ok
imx-sata 10000000.sata: port 0: Spinning up device...
imx-sata 10000000.sata: port 0: ok.
ata0: registered /dev/ata0
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
- declare the rigth mux for the GPIO used to enable the USB's 5V
- enable USB host controller
tested on i.MX53 START-R :
barebox@Freescale i.MX53 Quick Start-R Board:/ usb -f
USB: scanning bus for devices...
Bus 001 Device 001: ID 0000:0000 EHCI Host Controller
Using index 0 for the new disk
Bus 002 Device 003: ID 0951:1654 DT R500
Bus 002 Device 002: ID 0000:0000 EHCI Host Controller
3 USB Device(s) found
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
|
|
|
|
|
|
|
|
|
|
| |
tested on i.MX53 START-R :
barebox@Freescale i.MX53 Quick Start-R Board:/ ata0.probe=1
imx-sata 10000000.sata: port 0: SATA link ok
imx-sata 10000000.sata: port 0: Spinning up device...
imx-sata 10000000.sata: port 0: ok.
ata0: registered /dev/ata0
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
tested on i.MX53 START-R :
barebox@Freescale i.MX53 Quick Start-R Board:/ usb -f
USB: scanning bus for devices...
Using index 0 for the new disk
Bus 001 Device 002: ID 0951:1654 DT R500
Bus 001 Device 001: ID 0000:0000 EHCI Host Controller
Bus 002 Device 003: ID 0000:0000 EHCI Host Controller
3 USB Device(s) found
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
- declare the rigth mux for the GPIO used to enable the USB's 5V
- enable USB host controller
tested on i.MX53 START-R :
barebox@Freescale i.MX53 Quick Start-R Board:/ usb -f
USB: scanning bus for devices...
Bus 001 Device 001: ID 0000:0000 EHCI Host Controller
Using index 0 for the new disk
Bus 002 Device 003: ID 0951:1654 DT R500
Bus 002 Device 002: ID 0000:0000 EHCI Host Controller
3 USB Device(s) found
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
There are two versions of the i.MX53 LOCO:
- the MCIMX53-START board
- the MCIMX53-START-R board
The MCIMX53-START-R has a mc34708 pmic and is otherwise the similar to the
MCIMX53-START. To prepare for the START-R, move all common nodes to a new
imx53-qsb-common.dtsi
and remove everything but the board name and pmic from the imx53-qsb.dts.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|