| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This adds support for the Freescale i.MX6sx sabresdb board.
Tested are:
- UART
- The three SD card slots
- USB host
- USB otg (host and device mode)
- FEC (both)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
|
|
|
|
|
|
| |
Add support for phyBOARD-SUBRA which use a phyFLEX-i.MX6 (pfla02) module.
- i.MX6 SOLO with 512MB RAM
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
|
|
|
|
|
|
| |
Add support for phyBOARD-ALCOR which use a phyFLEX-i.MX6 (pfla02) module.
- i.MX6 Quad with 1GB RAM on two banks
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|\ |
|
| |
| |
| |
| |
| |
| |
| |
| | |
This adds xz decompression support from the kernel. Both compressing
the barebox binary with xz and decompressing xz files on the commandline
is supported.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|\ \ |
|
| |/
| |
| |
| |
| |
| |
| | |
The nitrogen6x have variants with 2GB SDRAM. Add support for them. The
imxcfg files are from U-Boot.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| | |
Boards like phyBOARD-WEGA RDK have an phyCORE-AM335x
connected with no SPI NOR flash. Added dts to support this.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|/
|
|
|
|
|
|
|
| |
Add support for PHYTEC's phyFLEX-AM335x.
Signed-off-by: Stefan Müller-Klieser <s.mueller-klieser@phytec.de>
[clean ups]
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|\ |
|
| |
| |
| |
| |
| |
| |
| | |
Added settings for 1GB RAM option.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| | |
Naming is confusing and wrong. Fixed it up.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|\ \ |
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The Karo TX6X family consists of different i.MX6Q/DL based System-on-Modules.
Add support for the TX6u 801x modules, that have an i.MX6DL SoC.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
| |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
For now only the Quad 1GB variant is supported.
Tested:
- starting barebox over USB
- writing barebox to NAND with barebox_update
- starting Linux kernel over TFTP
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|/
|
|
| |
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|\ |
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This commit adds a new Marvell Kirkwood-based board, by following the currently
supported boards.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|/
|
|
|
|
|
|
| |
This fixes various stability issues seen on new boards
with the old setup.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|\ |
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This will add support for Embedsky E9 board.
It is a small board based on i.MX6 Quad with 2G of RAM.
http://en.embedsky.com/product_info.php?cateid=169&id=169
Signed-off-by: Andrey Panov <rockford@yandex.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| | |
This adds support for 256MB and 128MB RAM configurations of the
phyCORE-AM335x. This is done as new images.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|/
|
|
| |
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
|
|
|
|
| |
Add *./mlo and *.mlospi to the clean rule and to .gitignore.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|\
| |
| |
| |
| |
| | |
Conflicts:
arch/arm/boards/Makefile
arch/arm/dts/Makefile
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This converts Marvell Armada XP based PlatHome Openblocks AX3-4
to PBL_MULTI_IMAGES. A DT overlay is added to keep possible
barebox-specific changes separated and added to lowlevel
board init.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This converts Marvell Armada XP based Marvell Armada XP GP
to PBL_MULTI_IMAGES. A DT overlay is added to keep possible
barebox-specific changes separated and added to lowlevel
board init.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This converts Marvell Armada 370 based Globalscale Mirabox
to PBL_MULTI_IMAGES. A DT overlay is added to keep possible
barebox-specific changes separated and added to lowlevel
board init.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
|
| |
| |
| |
| |
| |
| |
| | |
This converts Marvell Kirkwood based USI Topkick to
PBL_MULTI_IMAGES.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
|
| |
| |
| |
| |
| |
| |
| | |
This converts Marvell Kirkwood based Globalscale Guruplug to
PBL_MULTI_IMAGES.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
|
| |
| |
| |
| |
| |
| |
| | |
This reorders images/Makefile.mvebu targets by board to ease integration
of new boards.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The rule in barebox is to name the directories after
the modules. As hummingboard is just one of the
carriers for the MicroSOM module, name the directory
accordingly.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|/
|
|
|
|
|
| |
Tested on the phyCORE-imx27 to boot on NOR and NAND using the
registered update handlers.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
|
|
|
| |
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
|
|
|
|
|
|
| |
Allows to build persistent images for the Tegra124
line of SoCs.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|\ |
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
To make it clear that this image is only suitable
for loading via usbloader. We can't do anything
about this, as there is no upstream BCT available
for AC100.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
| |
| |
| |
| |
| | |
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Six images for the the 256MB and 512MB version with
different boot sources (MMC, NAND [different chips on
pre-/production modules]).
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| | |
Allows to build persistent images for the Tegra30
line of SoCs.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| | |
Allows to build persistent images for the Tegra20
line of SoCs.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|/
|
|
| |
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|\
| |
| |
| |
| |
| |
| |
| | |
Conflicts:
arch/arm/dts/tegra20-colibri.dtsi
arch/arm/dts/tegra20-paz00.dts
arch/arm/dts/tegra20.dtsi
drivers/clk/tegra/clk-periph.c
|
| |
| |
| |
| |
| | |
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|\ \ |
|
| |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
- Add images/Makefile.rockchip
- Allow multiple boards to be selected
- protect initcalls with appropriate of_machine_is_compatible
- rename board specific config to SoC config
- Add dtb file to compilation
- turn barebox_arm_reset_vectorto ENTRY_FUNCTION
- pass dtb to barebox_arm_entry
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Add support for Phytec phyCARD-i.MX6.
- 1GB RAM on two banks
- 1GB RAM on one bank
- 2GB RAM on two banks
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
this board is produced by Embest/Element 14 and is based on i.MX6 Solo
The following features are tested :
- UART2 (console)
- eMMC
- SDCard
- uSDCard
- Ethernet
- USB Host (through 4 ports hub)
- I2C 1/2/3
- 2 LEDs
Boot on eMMC and through USB loader are tested.
For more informations on this board : http://www.riotboard.org/
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|\
| |
| |
| |
| | |
Conflicts:
arch/arm/boards/phytec-phyflex-imx6/board.c
|
| |
| |
| |
| |
| | |
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|