summaryrefslogtreecommitdiffstats
path: root/images
Commit message (Collapse)AuthorAgeFilesLines
...
| * ARM: socfpga: add support for reflex achilles boardSteffen Trumtrar2017-05-041-0/+4
| | | | | | | | | | Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
| * ARM: socfpga: add arria10 supportSteffen Trumtrar2017-05-031-1/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Arria10 is a SoC + FPGA like the Cyclone5 SoCFPGA that is already supported in barebox. Both a the same in some parts, but totaly different in others. Most of the hardware blocks are the same in the SoC parts. The OCRAM is larger on the Arria10 and the SDRAM controller is different. The serial core only supports 32bit accesses (different to the 8bit accesses on the Cyclone5). As Arria10 has 256KB of OCRAM, it is possible to fit a larger barebox (and/or use PBL) instead of the two stage bootprocess used on the Cyclone5 and its 64KB OCRAM. Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* | Merge branch 'for-next/imx'Sascha Hauer2017-05-051-5/+41
|\ \ | |/ |/|
| * ARM: i.MX50: Add support for i.MX50 based Amazon Kindle e-book readersAlexander Kurz2017-04-241-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Kindle Model No. D01100 (Kindle Wi-Fi), D01200 (Kindle Touch) and EY21 (Kindle Paperwhite) are refered as the Kindle 4th and 5th generation. Those models are based on an i.MX50 SoC and use LPDDR1 or LPDDR2 Memory. The devices boot in internal boot mode from a build-in eMMC, alternatively some devices may be set into USB-downloader mode by pressing a specific key at startup. Add support for the i.MX50 based Kindle device and make barebox a drop-in replacement for the factory shipped u-boot image. Notable features: - Support for eMMC, USB, UART, I2C, SPI and Keys (except keyboard). - LPDDR1 and LPDDR2 setup is done via DCD, the same imximage may be used for USB-startup and for installation. - Support for vendor specific ATAGs that are required for the Kindle-System. - usbserial barebox console access by pressing Select button at startup, alternatively full console support on connector J14. Signed-off-by: Alexander Kurz <akurz@blala.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
| * ARM: imx6: add Hummingboard2 supportLucas Stach2017-04-101-5/+25
| | | | | | | | | | | | | | | | This adds support for the Hummingboard2 baseboard for the SolidRun MicroSOM modules. Signed-off-by: Lucas Stach <dev@lynxeye.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* | ARM: at91sam9x5ek: Actually build imageSascha Hauer2017-04-191-2/+2
|/ | | | | | | | The Kconfig variable is named CONFIG_MACH_AT91SAM9X5EK, not MACH_AT91SAM9X5EK. Reported-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* at91sam9x5ek: Convert to mult-image buildAndrey Smirnov2017-03-302-0/+8
| | | | | | | | Convert AT91SAM9X5-EK board code to multi-image build process, similar to how majority of i.MX board code is built. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* Merge branch 'for-next/rpi'Sascha Hauer2017-03-132-0/+12
|\
| * ARM: rpi: switch to DT probe and multi-image buildLucas Stach2017-03-022-0/+12
| | | | | | | | | | | | | | | | This commit switches the RaspberryPi arch over to probe Barebox from the builtin DT and enables multi-image builds. Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* | arm: boards: phytec-som-am335x: Remove 1GB RAM typeDaniel Schultz2017-03-011-6/+0
|/ | | | | | | | | This machine was a prototype and was never shipped to customers. Since it has no dependencies to any image, it can be removed. Signed-off-by: Daniel Schultz <d.schultz@phytec.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* i.MX: vf610: Add support for ZII VF610 Dev FamilyAndrey Smirnov2017-02-071-0/+5
| | | | | | | | | | | | | Add support for ZII VF610 Dev based designs such as: - VF610 Dev, revision B - VF610 Dev, revision C - CFU1, revision A - SPU3, revision A - SCU4 AIB, revision C Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* ARM: i.MX: Add WaRP7 board supportJuergen Borleis2017-01-201-0/+5
| | | | | Signed-off-by Juergen Borleis <jbe@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* ARM: rdu2: support QP variantLucas Stach2017-01-181-0/+5
| | | | | | | | This adds support for the QuadPlus variant of the board as a separate Barebox binary. Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* ARM: imx: Add support for ZII RDU2 boardAndrey Smirnov2017-01-181-0/+5
| | | | | | | | Add support for RDU2 board from Zodiac Inflight Innovations. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* ARCH: ARM: Add support for phytec-phycore-imx6ulChristian Hemp2017-01-101-0/+5
| | | | | | | | | | | Add support for the phycore i.MX6 UltraLite. - 512MB RAM - 512MB NAND - 10/100 Mbit Ethernet Signed-off-by: Christian Hemp <c.hemp@phytec.de> Signed-off-by: Stefan Lengfeld <s.lengfeld@phytec.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* i.MX: Add support for VF610 Tower boardAndrey Smirnov2016-11-111-0/+5
| | | | | | | Add support for VF610 Tower board. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* ARM: imx6: add support for Auvidea H100Lucas Stach2016-10-111-0/+5
| | | | | | | | | | | The Auvidea H100 is a baseboard for the SolidRun MicroSOM, which provides HDMI IN/OUT capabilities. Currently supported is only a combination of the H100 baseboard with a i2eX MicroSOM. Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* Merge branch 'for-next/mvebu'Sascha Hauer2016-10-101-29/+8
|\
| * ARM: mvebu: add support for Netgear RN2120Uwe Kleine-König2016-10-071-0/+8
| | | | | | | | | | Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
| * images: mvebu: don't generate uart imagesUwe Kleine-König2016-10-041-29/+0
| | | | | | | | | | | | | | | | kwboot knows how to work with an image for a different boot medium now. So there is no reason to generate a dedicated UART image any more. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* | Merge branch 'for-next/imx'Sascha Hauer2016-10-101-4/+10
|\ \
| * | ARM: i.MX53 Vincell: Add NAND xload supportSascha Hauer2016-09-221-4/+10
| |/ | | | | | | | | | | | | | | The Vincell boards do the SDRAM setup from board init code, so the image size is limited to the internal SRAM size. To overcome this limitation use the NAND xload support. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* | Add support for Baltos systemsYegor Yefremov2016-10-071-0/+8
| | | | | | | | | | | | | | | | OnRISC Baltos devices are based on a am335x SoC and can be booted either from MMC or NAND. Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* | Add comp_copy function for use with CONFIG_IMAGE_COMPRESSION_NONESascha Hauer2016-09-151-1/+1
|/ | | | | | | | | | The Makefile compression commands all append the size of the uncompressed image. With CONFIG_IMAGE_COMPRESSION_NONE simply 'shipped' is used which does not append the size. Add and use a special comp_copy function which adds the size. This helps us to get the uncompressed image size in the startup code later. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* ARM: Add phyCORE-RK3288 SOM supportWadim Egorov2016-09-011-0/+4
| | | | | | | | | The phyCORE-RK3288 aka PCM-059 is a SoM (System on Module) containing a RK3288 SoC. The module can be connected to different carrier boards. Signed-off-by: Wadim Egorov <w.egorov@phytec.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* ARM: nitrogen: rename to nitrogen6Lucas Stach2016-08-031-15/+15
| | | | | | | | Now that the MAX variant of the board is also supported by the same code, rename the board directory to the more generic nitrogen6. Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* ARM: add support for Nitrogen6MAX QP variantLucas Stach2016-08-031-0/+5
| | | | | Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* ARM: i.MX: karo-tx6: Add support for the 512MiB i.MX6s variantSascha Hauer2016-07-061-0/+5
| | | | | | This adds support for the TX6S-8x35 board variant. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* socfpga: Stop putting 512 byte header on SocFPGA imagesTrent Piepho2016-05-231-1/+1
| | | | | | | | | | | | Since images without the extra header now boot correctly, stop adding it. This makes the image 512 bytes smaller. It also gives the image a correct barebox header. The 512 byte extra header looked like a barebox header (had a "barebox\n" signature) but had incorrect size and text start fields. Signed-off-by: Trent Piepho <tpiepho@kymetacorp.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* Merge branch 'for-next/imx6-phytec'Sascha Hauer2016-05-091-0/+15
|\
| * ARM: phytec-som-imx6: add phyCORE-i.MX6 DualLiteStefan Christ2016-05-021-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add Phytec phyCORE-i.MX6 SOM. Support: - imx6dl-phytec-phycore-som-emmc: - 1GB RAM on 1 Bank with 64Bit - 10/100MBit Ethernet - SPI NOR - eMMC - SD - UART Signed-off-by: Stefan Christ <s.christ@phytec.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
| * ARM: phytec-som-imx6: add phyCORE-i.MX6 Quad 2GiB RAMChristian Hemp2016-05-021-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add new Phytec phyCORE-i.MX6 SOM: Support: - imx6q-phytec-phycore-som-emmc: - 2GiB RAM on 1 Bank with 64Bit - 1GBit Ethernet - SPI NOR - eMMC - SD - UART Signed-off-by: Christian Hemp <c.hemp@phytec.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
| * ARM: imx6q: add support for phyBOARD-SUBRA-i.MX6 QuadStefan Christ2016-05-021-0/+5
| | | | | | | | | | | | | | | | | | Add support for phyBOARD-SUBRA-i.MX6 with phyFLEX-i.MX6 Quad 1GiB on one bank. This patch factors out the common device tree nodes for the Quad and Solo variant into 'imx6qdl-phytec-phyboard-subra.dtsi'. Signed-off-by: Stefan Christ <s.christ@phytec.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* | Merge branch 'for-next/imx'Sascha Hauer2016-05-091-0/+5
|\ \
| * | ARM: i.MX: karo-tx6: Add support for the 2GiB i.MX6q+ board variantSascha Hauer2016-04-281-0/+5
| |/ | | | | | | | | | | Different SDRAM setup, but same board otherwise. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* | images: Makefile.socfpga: fix typoUlrich Ölmann2016-04-271-1/+1
| | | | | | | | | | Signed-off-by: Ulrich Ölmann <u.oelmann@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* | ARM: board: phytec-som-am335x: RAM timings for phycore-r2 1GBTeresa Remmet2016-04-191-0/+6
|/ | | | | | | | Add new RAM Timings for phyCORE R2 with MT41K512M16HA-125IT 1024MB mounted. Signed-off-by: Teresa Remmet <t.remmet@phytec.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* Merge branch 'for-next/imx'Sascha Hauer2016-03-111-0/+5
|\
| * ARM: i.MX: karo-tx6: Add support for the i.MX6q 1GiB variantSascha Hauer2016-03-021-0/+5
| | | | | | | | | | | | | | The i.MX6q variant is basically the same as the i.MX6dl variant, just with another SoC and the usual i.MX6q/i.MX6dl adjustments. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* | Merge branch 'for-next/arm'Sascha Hauer2016-03-111-1/+9
|\ \
| * | ARM: socfpga: socdk: Fix typo in MakefileSascha Hauer2016-03-011-1/+1
| | | | | | | | | | | | Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
| * | Terasic DE0-Nano-SoC: add supportTim Sander2016-03-011-0/+8
| |/ | | | | | | | | | | | | | | | | | | | | | | v7: eof whitespace fixes A Patch for supporting the Terasic DE0 NANO-SoC with barebox. The pretty similar Socrates Board was taken as a starting point with pulling in the memory timings/pinmux from http://rocketboards.org/foswiki/view/Documentation/AtlasSoCCompileHardwareDesign Signed-off-by: Tim Sander <tim@krieglstein.org> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* | ARM: boards: phytec-som-am335x: New RAM Timings for phyCORE-AM335x-R2Teresa Remmet2016-02-171-0/+6
| | | | | | | | | | | | | | Add RAM timings for phyCORE-AM335x-R2 256MB RAM. Signed-off-by: Teresa Remmet <t.remmet@phytec.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* | ARM: board: phytec-som-am335x: RAM timings for phyCORE-AM335x-R2Arnd Beuscher2016-02-171-0/+6
|/ | | | | | | | | Add RAM Timings for new phyCORE-AM335x-R2 SoM with 512MB (MT41K256M16TW107IT). Signed-off-by: Arnd Beuscher <a.beuscher@phytec.de> Sigend-off-by: Teresa Remmet <t.remmet@phytec.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* Merge branch 'for-next/hab'Sascha Hauer2016-02-083-52/+10
|\
| * images: imx: Add targets for signed images and signed usb imagesSascha Hauer2016-02-042-1/+8
| | | | | | | | | | | | | | Add .simximg target for signed images and .usimximg for signed images suitable for USB upload Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
| * Make: i.MX: Allow to pass config file to cmd_imx_imageSascha Hauer2016-02-041-2/+2
| | | | | | | | | | | | | | | | Pass the config file to cmd_imx_image as arguments to make it more flexible. Also add the possibility for another arg containing additional options. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
| * scripts: imx: Generate signed images with imx-imageSascha Hauer2016-02-042-49/+0
| | | | | | | | | | | | | | | | | | | | | | The imx-image tool can now generate signed images itself, so we can switch to this mechanism: - Move the CSF templates to header files which can be included by the flash config files - remove images/Makefile.imxhabv4 which is no longer necessary. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* | Add initial support for Netgear ReadyNAS 104Uwe Kleine-König2016-01-221-0/+11
|/ | | | | | | | | | | | | | | Currently only second stage booting from the vendor U-Boot is tested. I don't want to flash barebox into NAND yet because UART-booting for recovery doesn't work for me. Working so far are: - UART - networking - nand flash Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* ARM: mx6sx-sabresdb: set proper hostnameLucas Stach2015-11-301-0/+10
| | | | | | | | Also move the initcall to the level matching the name of the function. Signed-off-by: Lucas Stach <dev@lynxeye.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
generated by cgit v1.2.3 (git 2.39.1) at 2024-05-21 06:45:24 +0000